Digital Projection HIGHlite Laser 3D Series User manual

Rev C February 2015
HIGHlite Laser 3D Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICK-START GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
114-913C

page i
Digital Projection HIGHlite Laser 3D Series
Rev C February 2015
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2015 Digital Projection Ltd. All rights reserved.
Notes

page ii
Digital Projection HIGHlite Laser 3D Series
Rev C February 2015
Laser Information
Caution-useofcontrolsoradjustmentsorperformanceofproceduresotherthanthosespeciedhereinmayresultin
hazardous radiation exposure.
Notes
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
455-470nm <13Watts
CLASSIFIED EN/IEC 60825-1 2007

page iii
Digital Projection HIGHlite Laser 3D Series
Rev C February 2015
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• Support for most 3D formats.
• HDBaseT® for transmission of uncompressed High Denition Video up to 100 m from the source.
• 3G-SDI with loop-through.
• Edge Blend.
• Blanking control for custom input window sizing.
• Cornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.
• Control via LAN and RS232.
• Motorised lens mount.
A serial number is located on the side of the projector. Record it here:
Notes

page iv
Digital Projection HIGHlite Laser 3D Series
Rev C February 2015
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
WHAT’S IN THE BOX? ................................................................... 3
CONNECTING THE POWER SUPPLY ............................................. 4
PROJECTOR OVERVIEW ............................................................... 5
Front and rear views ............................................................................. 5
Control panel......................................................................................... 6
REMOTE CONTROL....................................................................... 7
Infrared reception................................................................................ 10
POSITIONING THE SCREEN AND PROJECTOR........................... 11
Roll and pitch ...................................................................................... 12
CHANGING THE LENS................................................................. 13
The lens hood ..................................................................................... 13
Inserting a new lens ............................................................................ 14
Removing the lens .............................................................................. 15
CHANGING THE FILTERS ............................................................ 16
OPERATING THE PROJECTOR.................................................... 17
Switching the projector on................................................................... 17
Switching the projector off................................................................... 17
Selecting an input signal or test pattern.............................................. 18
Input signal ........................................................................................ 18
Test pattern ........................................................................................ 18
Adjusting the lens................................................................................ 19
Lens menu......................................................................................... 19
Remote control.................................................................................... 19
Adjusting the image............................................................................. 20
Orientation ......................................................................................... 20
Keystone ........................................................................................... 20
Picture .............................................................................................. 20
CONNECTION GUIDE ............................................................................21
SIGNAL INPUTS .......................................................................... 23
Digital inputs and outputs.................................................................... 23
Analog inputs ...................................................................................... 24
EDID on the DVI and VGA inputs........................................................ 25
Using HDMI/DVI switchers with the projector ..................................... 25
3D connections ................................................................................... 26
3D sources up to 60Hz requiring frame doubling and left/right interleaving.......... 26
Frame sequential 3D sources up to 120Hz ................................................. 26
Dual Pipe 3D ...................................................................................... 26
3D Sync............................................................................................... 27
3D Sync in ......................................................................................... 27
3D Sync out ....................................................................................... 27
CONTROL CONNECTIONS........................................................... 28
LAN connection examples .................................................................. 29
RS232 connection example ................................................................ 30

page v
Digital Projection HIGHlite Laser 3D Series
Rev C February 2015
OPERATING GUIDE ................................................................................31
USING THE MENUS ..................................................................... 33
Opening the OSD................................................................................ 33
Opening a menu.................................................................................. 33
Exiting menus and closing the OSD.................................................... 33
Inside a menu...................................................................................... 34
Accessing sub-menus........................................................................... 34
Executing commands............................................................................ 34
Editing projector settings..................................................................... 35
Choosing a value from a list ................................................................... 35
Changing the value without viewing the list................................................. 35
Using a slider to set a value.................................................................... 35
USING THE PROJECTOR............................................................. 36
Main menu .......................................................................................... 36
Lens menu .......................................................................................... 37
Lens Control....................................................................................... 37
Lens Center ....................................................................................... 37
Image menu ........................................................................................ 38
Brightness and Contrast ........................................................................ 38
Gamma............................................................................................. 39
Adaptive Contrast ................................................................................ 39
Saturation, Hue, Sharpness and Noise Reduction ........................................ 39
Position and Phase .............................................................................. 40
Resync ............................................................................................. 40
Color menu.......................................................................................... 41
Color Space ....................................................................................... 41
Color Temperature ............................................................................... 42
Gamut .............................................................................................. 43
User Gamut........................................................................................ 44
RGB Lift and Gain................................................................................ 46
Geometry menu .................................................................................. 47
Aspect Ratio....................................................................................... 47
Overscan........................................................................................... 48
Keystone ........................................................................................... 49
Rotation ............................................................................................ 51
Pincushion / Barrel............................................................................... 52
Corners............................................................................................. 53
Reset................................................................................................ 54
Blanking ............................................................................................ 55
Edge Blend menu................................................................................ 56
Blend Width........................................................................................ 57
Black Level Uplift ................................................................................. 58
Possible Geometry and Edge Blend combinations............................. 59
3D menu.............................................................................................. 60
3D types............................................................................................ 61
Some 3D settings explained ................................................................... 62
Frame rate multiplication in 3D images ...................................................... 63
Laser menu ......................................................................................... 64
Setup menu......................................................................................... 65
Infrared Remote .................................................................................. 66
Network ............................................................................................ 67
On Screen Display ............................................................................... 68
Presets ............................................................................................. 69
Information menu ................................................................................ 70
Factory Reset ..................................................................................... 70
CONTENTS (continued)

page vi
Digital Projection HIGHlite Laser 3D Series
Rev C February 2015
REFERENCE GUIDE................................................................................71
THE DMD™.................................................................................. 74
CHOOSING A LENS ..................................................................... 76
Basic calculation ................................................................................. 77
Basic calculation example................................................................... 78
Full lens calculation............................................................................. 79
Introducing TRC .................................................................................. 79
Calculating TRC .................................................................................. 80
Calculating the throw ratio with TRC ......................................................... 81
Full lens calculation example .............................................................. 82
SCREEN REQUIREMENTS........................................................... 83
Fitting the image to the DMD™........................................................... 83
WUXGA images displayed full width ......................................................... 83
WUXGA images displayed with a height of 1080 pixels.................................. 84
WUXGA images displayed full height ........................................................ 85
Diagonal screen sizes......................................................................... 86
Fitting the image to the screen............................................................ 87
Positioning the screen and projector................................................... 88
POSITIONING THE IMAGE........................................................... 89
Maximum offset range......................................................................... 91
ASPECT RATIOS EXPLAINED...................................................... 92
Aspect ratio examples......................................................................... 93
FRAME RATES AND PULLDOWNS EXPLAINED........................... 95
Interlaced and progressive scan ......................................................... 95
Frame rates of image sources ............................................................ 95
Pulldowns - conversion into destination formats................................. 96
2:3 (normal) pulldown ........................................................................... 96
2:3:3:2 (advanced) pulldown................................................................... 97
APPENDIX A: LENS PART NUMBERS.......................................... 98
APPENDIX B: LENS CHARTS ...................................................... 99
How to use the lens charts ..................................................................... 99
TRC values applied in the charts ........................................................... 100
Full DMD™ width images..................................................................... 101
1.25:1 images ................................................................................... 102
1.33:1 images ................................................................................... 103
APPENDIX C: SUPPORTED SIGNAL INPUT MODES .................. 104
2D input modes................................................................................. 104
3D input modes................................................................................. 106
APPENDIX D: MENU MAP.......................................................... 107
APPENDIX E: WIRING DETAILS..................................................113
Signal inputs and outputs.................................................................. 113
VGA ............................................................................................... 113
HDMI 1 and 2 ................................................................................... 114
DVI ................................................................................................ 115
3G-SDI In, 3G-SDI Out........................................................................ 116
Component 1.................................................................................... 116
Component 2.................................................................................... 116
Control connections .......................................................................... 117
LAN ............................................................................................... 117
RS232 ............................................................................................ 117
Trigger 1 & Trigger 2 ........................................................................... 118
IR input ........................................................................................... 118
USB ............................................................................................... 118
3D Sync IN and 3D Sync OUT .............................................................. 118
CONTENTS (continued)

page vii
Digital Projection HIGHlite Laser 3D Series
Rev C February 2015
APPENDIX F: GLOSSARY OF TERMS.........................................119
TECHNICAL SPECIFICATIONS .................................................. 130
Models............................................................................................... 130
Inputs and outputs............................................................................. 131
Bandwidth ......................................................................................... 131
Remote control and keypad .............................................................. 131
Automation control ............................................................................ 131
Color temperature ............................................................................. 131
Lenses............................................................................................... 132
Lens mount ....................................................................................... 132
Mechanical mounting ........................................................................ 132
Orientation......................................................................................... 132
Electrical and physical specications................................................ 133
Safety & EMC regulations................................................................. 133
CONTENTS (continued)

Rev C February 2015
HIGHlite Laser 3D Series
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE
4

Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
IN THIS GUIDE
Rev C February 2015
IN THIS GUIDE
What’s In The Box?............................................................................................. 3
Connecting The Power Supply........................................................................ 4
Projector Overview............................................................................................. 5
Front and rear views ...................................................................................................5
Control panel ...............................................................................................................6
Remote Control.................................................................................................... 7
Infrared reception......................................................................................................10
Positioning The Screen And Projector....................................................... 11
Roll and pitch ............................................................................................................12
Changing The Lens........................................................................................... 13
The lens hood............................................................................................................13
Inserting a new lens..................................................................................................14
Removing the lens ....................................................................................................15
Changing The Filters........................................................................................ 16
Operating The Projector................................................................................. 17
Switching the projector on.......................................................................................17
Switching the projector off.......................................................................................17
Selecting an input signal or test pattern.................................................................18
Input signal......................................................................................................................18
Test pattern .....................................................................................................................18
Adjusting the lens .....................................................................................................19
Lens menu ......................................................................................................................19
Remote control................................................................................................................19
Adjusting the image..................................................................................................20
Orientation ......................................................................................................................20
Keystone .........................................................................................................................20
Picture.............................................................................................................................20

page 3
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
Rev C February 2015
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
Only one remote will be supplied
with the projector. For more
information, see Remote Control
further in this guide.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Do not use the short lens hood
with the long throw lens.
For further information about using
the right lens and hood, see The
lens hood further in this guide.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
(116-088)
2x AAA batteries
User Manual on disc
(115-759)
Important Information (114-914)
Power cable, Europe
(112-001)
Power cable, North America
(112-002)
Projector
Power cable, United Kingdom
(112-000)
VGA cable
SHUTTER
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT
HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR

page 4
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Rev C February 2015
Connecting The Power Supply
Lift the cable lock up, push the mains connector in rmly and
push the lock down to secure the cable.
1AC mains inlet with cable lock
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
1

page 5
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C February 2015
Projector Overview
Front and rear views
1Control panel
2Connection panel
3Air outlet
4Lens hood
5Front infrared window
6Power switch and power connection
7Air outlet
8Rear infrared window
9Air inlet
10 Adjustable feet
Notes
Do not use the short lens hood
with the long throw lens.
For further information about using
the right lens and hood, see The
lens hood further in this guide.
Front view
4 5
3
12
6
Rear view
7 8
10
9

page 6
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C February 2015
Control panel
1ON indicator (green)
Behavior Meaning
Off The projector is switched off.
Flashing The projector is warming up or cooling down.
On The projector is switched on (Normal mode).
2ERROR indicator (red)
Behavior Meaning
Flash three times, then pause Fan failure.
Flash four times, then pause Over temperature.
Flash ve times, then pause Filter failure.
On System error.
3ENTER button
Conrm your choice when navigating the OSD.
Access the Lens Control setting: shift the lens, zoom and focus the image.
4Arrow buttons
Navigate the OSD, edit settings.
5STANDBY indicator (blue)
Behavior Meaning
On The projector is in STANDBY mode.
6MENU button
Access the projector OSD (on-screen display).
7INPUT button
Select input source.
8STBY button
Switch the projector on and off (in STANDBY mode)
ENTER
ON
STANDBY
MENU
INPUT
STBY
ERROR
1
6
2
4
57
8
3
Notes
During startup all LEDs light up
at the same time to indicate the
projector is carrying out a self-test.

page 7
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C February 2015
Remote Control
1Power ON / OFF
2Shutter OPEN / CLOSE
3MENU
Access the projector OSD (on-screen display). If the OSD is open, press this button to
go back to the previous menu.
4Navigation
Navigate through the menus with the arrows, conrm your choice with OK.
In LENS SHIFT mode the arrows are used to move the lens. See 7below.
5EXIT
Close the OSD.
6Focus IN / OUT
Adjust focus.
7SHIFT
Press and hold this button, then press the Navigation arrow buttons to move the lens.
8INFO
Access information about the projector.
9Zoom IN / OUT
Adjust zoom.
continues on next page...
Notes
Remote control
SHUTTER
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR
1
2
4
5
9
3
8
6
7

page 8
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C February 2015
10 ALT
Press and hold this button to access alternative functions for all
buttons with a green label.
11 HDMI 1 / BRI / numeric input 1
Select the HDMI 1 input.
Use with ALT to bring up the Brightness control, then adjust the
value with the LEFT and RIGHT arrow buttons.
12 HDMI 2 / CON / numeric input 2
Select the HDMI 1 input.
Use with ALT to bring up the Contrast control, then adjust the value
with the LEFT and RIGHT arrow buttons.
13 DVI / GAMMA / numeric input 3
Select the DVI input.
Use with ALT to switch to the next Gamma value:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
14 DISPLAYPORT / R / numeric input 4
Use with ALT to switch the red DMD on and off. This functionality is
disabled when the projector is showing a test pattern.
15 HD-T / G / numeric input 5
Select the HDBaseT input.
Use with ALT to switch the green DMD on and off. This functionality is
disabled when the projector is showing a test pattern.
16 3GSDI / B / numeric input 6
Select the 3G-SDI input.
Use with ALT to switch the blue DMD on and off. This functionality is
disabled when the projector is showing a test pattern.
continues on next page...
Notes
DISPLAYPORT is not available on
this projector.
Remote control
SHUTTER
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR
16
12
15
14
10
13
11

page 9
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C February 2015
17 VGA / 3D / numeric input 7
Select the VGA input.
Use with ALT to toggle the 3D Format setting between Off and Auto.
18 COMP1 / EYE / numeric input 8
Select the Component 1 input.
Use with ALT to switch between left and right eye 3D dominance.
19 COMP2 / PIP / numeric input 9
Select the Component 2 input.
20 TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, CheckerBoard,
CrossHatch, V Burst, H Burst, ColorBar...
21 ADDR / ALL
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until the indicator starts ashing.
2. Release this button and while the indicator is still ashing, enter
a two-digit address using the numeric input buttons. The indicator
will ash three times quickly to conrm the change.
To unassign an address and return to the default address 00,
• Press and hold ALT and this button simultaneously until the
indicator ashes to conrm the change.
Remote control
SHUTTER
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR
21
18
19
17
20
Notes
PIP and SWAP are not available on
this projector.

page 10
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C February 2015
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of
acceptance when trying to control the projector.
40°
40°
Infrared reception
Notes

page 11
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev C February 2015
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling mounting.
1Four adjustable feet
2Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm into
the body of the projector.
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 30
cm (12 in) of space between the
ventilation outlets and any wall,
and 10 cm (4 in) on all other
sides.
Do not stack more than 3
projectors.
1
2
1
1
1
2
2
2
2
2

page 12
Digital Projection HIGHlite Laser 3D Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev C February 2015
Roll and pitch
The projector can be operated in numerous positions.
The only non-workable angle is in portrait mode with inputs facing upward, as shown in the diagram.
1Non-workable angle
2Workable angles
Notes
360° 2
Pitch
30°
330° 2
1
Roll