Digital Projection SHOWlite 3000sx User manual

The SHOWLITE range of
SUPER-HIGH-BRIGHTNESS DIGITAL VIDEO PROJECTORS
USER MANUAL
Revision A - 11/01/2002

Please read this manual carefully before using your Showlite projector and keep the
manual handy for future reference.
Your serial number is located on the bottom of your projector. Record it here:
CAUTION: To turn off main power, be sure to remove plug from power outlet.
The outlet socket should be located as near to the equipment as possible, and be
easily accessible.
CAUTION: To prevent electrical shock. Do not open the cabinet. No user
serviceable parts inside. Refer servicing to qualified service personnel.
WARNING: To prevent fire or shock, do not expose this unit to rain or moisture.
WARNING: Do not use this unit’s grounded plug with an extension cord or in a
power outlet unless all three prongs can be fully inserted.
WARNING: Do not open the cabinet. There are high-voltage components inside.
All servicing must be done by qualified service personnel.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
3. GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO
7779.
Important Information
LBV00073; Revision A - 11/01/2002

RF Interference
The Federal Communications Commission does not allow any modifications or
changes to the unit EXCEPT those specified in this manual. Failure to comply with
this government regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
i) Re-orient or relocate the receiving antenna.
ii) Increase the separation between the equipment and the receiver.
iii) Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
iv) Consult the dealer or an experienced radio/television technician for help.
LBV00073; Revision A - 11/01/2002

Veuillez lire ce manuel avec attention avant d’utiliser votre projecteur et gardez ce
manuel à portée de main afin de pouvoir y recourir facilement. Votre numéro de
série est situé sur le fond de votre projecteur. Reportez le ici:
ATTENTION: Pour couper complètement l’alimentation, retirez la prise du
secteur. La prise du secteur doit être accessible et installée le plus près possible de
l’appareil.
ATTENTION: Pour éviter tout choc électronique, n’ouvrez pas le boîtier. Les
piéces internes ne sont pas réparables par l’utilisateur. Pour toute réparation,
adressez-vous à un réparateur agrée Digital Projection.
AVERTISSEMENT: Afin de prevenier tout Risque d’incendie ou de choc
électrique, n’exposez pas cet appareil à la pluie ou à l’humidité.
AVERTISSEMENT: N’utilisez pas la prise avec terre de a’ppareil avec une
rallonge ou une autre prise, a moins que les trois brouches puissent être
completement insérées.
AVERTISSEMENT: N’ouvrez pas le boîtier. A l’intérieur se trouvent des
composants à haute tension. Toute réparation doit être faite par du personnel
agrée Digital Projection.
DOC avis de Conformation
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le Matériel Brouilleur du Canada.
3. Réglement sur les informations concernant les nuisances
acoustiques GSGV
Le niveau de pression sonore est inférieur à 70 dB (A) conformément à la norme
ISO 3744 ou ISO 7779.
Informations Importantes
LBV00073; Revision A - 11/01/2002

Directives covered by this Declaration
89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC & 93/68/EEC.
73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC.
Products covered by this Directive
Large Screen Projector type: .
Basis on which Conformity is being declared
The product identified above comply with the protection requirements of the above EU
directives, and the manufacturer has applied the following standards:-
EN 55022:1998 - Limits and Methods of Measurements of Radio Disturbance Characteristics
Information Technology Equipment.
EN 55024:1998 - Limits and Methods of Immunity Characteristics of Information
Technology Equipment.
EN 61000-3-2:1998 - Harmonic Current Emissions.
EN 61000-3-3:1998 - Immunity to Voltage Fluctuations and Flicker.
The technical documentation required to demonstrate that the product met the requirements
of the Low Voltage directive has been compiled by the signatory below and is available for
inspection by the relevant enforcement authorities. The CE mark was first applied in May
2001.
Signed:
Authority: D.J. Quinn, Product Development Director
Date: 14th September 2001
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and
limitations to use which must be observed when these products are taken into service to
maintain compliance with the above directives. Details of these special measures are
available on request, and are also contained in the product manuals.
Declaration of Conformity
LBV00073; Revision A - 11/01/2002

Directives covered by this Declaration
89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC & 93/68/EEC.
73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC.
Products covered by this Directive
Large Screen Projector type: .
Basis on which Conformity is being declared
The product identified above comply with the protection requirements of the above EU
directives, and the manufacturer has applied the following standards:-
EN 55022:1998 - Limits and Methods of Measurements of Radio Disturbance Characteristics
Information Technology Equipment.
EN 55024:1998 - Limits and Methods of Immunity Characteristics of Information
Technology Equipment.
EN 61000-3-2:1998 - Harmonic Current Emissions.
EN 61000-3-3:1998 - Immunity to Voltage Fluctuations and Flicker.
The technical documentation required to demonstrate that the product met the requirements
of the Low Voltage directive has been compiled by the signatory below and is available for
inspection by the relevant enforcement authorities. The CE mark was first applied in May
2001.
Signed:
Authority: D.J. Quinn, Product Development Director
Date: 14th September 2001
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and
limitations to use which must be observed when these products are taken into service to
maintain compliance with the above directives. Details of these special measures are
available on request, and are also contained in the product manuals.
LBV00073; Revision A - 11/01/2002

From time to time revisions will be issued to this manual. To maintain a correct and
up to date copy of the manual it is important that the instructions given in revision
notices are carried out.
The person carrying out the revision should complete the table below.
Revision No Revision Details Date Revised
Revision Record
LBV00073; Revision A - 11/01/2002

Overview
OVERVIEW
LBV00073; Revision A - 11/01/2002

The and are the finest, most technically advanced
projectors available today. The projectors enable you to project exceptionally
bright, precise images up to 300 inches across (measured diagonally) from your PC
or Macintosh computer, VCR, document camera, laser disc player, DVD player and
even an HD VCR or HD laser disc player.
Please read the following before proceeding
An Outline of Contents is given overleaf which provides an overview of the five
sections, A to E, in this manual and lists all the major topics covered along with
their location. This outline allows the user to direct themselves to the appropriate
section of this manual where a detailed contents page will provide the exact location
of the topic required. Section identifiers are also provided on the outside edge of the
pages to allow the quick location of individual sections.
The user is strongly recommended to read Section A: Overview before unpacking
or switching on the projector, paying particular attention to the safety warnings
provided.
Disclaimer Digital Projection makes a sincere effort to ensure accuracy and quality of it's published materials;
however, no warranty, expressed or implied, is provided. Digital Projection disclaims any direct or indirect damages
resulting from the use of any information in this manual.
Introduction
Introduction
INTRODUCTION
LBV00073; Revision A - 11/01/2002

Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Office: As Above
Tel: [phone]
Fax:[phone]
E-Mail:[email protected], [email protected]
Web Site:www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel: (USA) 770 420 1350
Fax: (USA) 770 420 1360
E-Mail: [email protected]
Web Site: www.digitalprojection.com
Introduction
INTRODUCTION
LBV00073; Revision A - 11/01/2002

Section A: Overview
Packaging .................................................................. A—1
Safety Advice ............................................................. A—3
Components ............................................................... A—6
Section B: System Installation
Installation Guidelines................................................. B—1
Installation .................................................................. B—8
Basic Operation ......................................................... B—11
Input Source Connections ......................................... B—14
Section C: System Operation
Remote Control Overview .......................................... C—1
Menu System Overview ............................................. C—8
Menu Operation - SHOWlite 3000sx ......................... C—10
Advance Menu - SHOWlite 3000sx .......................... C—14
Source Select - SHOWlite 3000sx .............................. C—15
Adjust (Source) - SHOWlite 3000sx ............................ C—19
Volume - SHOWlite 3000sx ....................................... C—27
Ref Adj - SHOWlite 3000sx ........................................ C—27
Factory Default - SHOWlite 3000sx ........................... C—29
Projector Options - SHOWlite 3000sx ........................ C—30
Help - SHOWlite 3000sx ............................................ C—43
Test Pattern - SHOWlite 3000sx ................................. C—45
Menu Operation - SHOWlite 4000gv ........................ C—46
Advance Menu - SHOWlite 4000gv ......................... C—50
Source Select - SHOWlite 4000gv .............................. C—51
Introduction
Outline of Contents
INTRODUCTION
LBV00073; Revision A - 11/01/2002

Section C: System Operation (Cont.)
Picture - SHOWlite 4000gv ........................................ C—54
Volume - SHOWlite 4000gv ...................................... C—54
Image Options - SHOWlite 4000gv ........................... C—55
Projector Options - SHOWlite 4000gv ........................ C—63
Tools - SHOWlite 4000gv ........................................... C—75
Help - SHOWlite 4000gv ........................................... C—77
Test Pattern - SHOWlite 4000gv ................................ C—79
PC Card Viewer - SHOWlite 4000gv ......................... C—80
PC Card Viewer Utility Software - SHOWlite 4000gv ... C—86
Section D: Advanced User Information
Screen Illuminance ..................................................... D—1
Projector Orientation ................................................... D—2
Multiple Projection Operation .................................... D—2
Link Mode Menu Items ............................................... D—8
External Connections ................................................. D—10
Projector Dimensions ................................................ D—15
Technical Specification ............................................. D—16
Section E: Maintenance
Lamp Replacement .................................................... E—1
Cleaning/Replacing the Filter ..................................... E—4
Trouble Shooting ......................................................... E—5
Appendix
Glossary.............................................................................. i
Introduction
INTRODUCTION
LBV00073; Revision A - 11/01/2002

Packaging ........................................................................ A—1
Projector Packaging.................................................... A—1
Lens Packaging........................................................... A—2
Safety Advice ................................................................... A—3
Fire and Shock Precautions......................................... A—3
Lamp Precautions ....................................................... A—3
Power Supply ............................................................. A—4
Installation Advice ..................................................... A—5
Components ..................................................................... A—6
Part Names ................................................................. A—6
Control Panel ............................................................. A—8
Left Terminal Panel - SHOWlite 3000sx .................... A—10
Left Terminal Panel - SHOWlite 4000gv ................... A—12
PC Card Viewer - SHOWlite 4000gv ......................... A—14
Right Terminal Panel - SHOWlite 3000sx .................. A—15
Right Terminal Panel - SHOWlite 4000gv ................. A—17
Remote Control ........................................................ A—19
Overview
Section A: Overview
OVERVIEW
LBV00073; Revision A - 11/01/2002

LBV00073; Revision A - 11/01/2002

Projector Packaging
The following components should be contained within the projector packaging.
Should any of the components be absent, please contact the dealer who supplied the
projector, or Digital Projection Limited for all countries excluding North America
or Digital Projection Inc. for North American Customers.
1 x Projector. 1 x Remote Control Unit with 2 x AAA Batteries.
1 x Lens Cap
1 x RGB Signal Cable 1 x Remote Control Cable
(supplied with 4000gv only)
1 x String and Rivet
A—1
Overview
Packaging
OVERVIEW
LBV00073; Revision A - 11/01/2002
R
M
E
N
U
E
N
T
E
R
C
A
N
C
E L
SELECT
LENS SHIFT
LEFT
ZOOMFOCUS
UP
DOWN
RIGHT
AUTO
ADJUST
LAMP STATUS POWER
ON/STAND BY
SOURCE

3 x AC Power Cables
(1 x 220-240V - Europe, 1 x 120V - North America and 1 x 100V - Japan)
1 x CD ROM 1 x Ferrite Clamp Core 1 x User Manual
(supplied with 4000gv only)
All packaging should be retained to provide maximum protection during future
shipping of the projector.
Lens Packaging
Lenses are supplied as individual items and the packaging may differ depending on
the version ordered. Please refer to the instructions supplied with your lens.
A—2
Overview
OVERVIEW
LBV00073; Revision A - 11/01/2002

The safety instructions provided in this manual are to ensure the long life of your
projector and to prevent fire and shock. Please read them carefully and heed all
warnings.
Fire and Shock Precautions
Ensure that there is sufficient ventilation and that vents are unobstructed to prevent
potentially dangerous concentrations of ozone and the build-up of heat inside your
projector. Allow at least 10cm (3”) of space between your projector and a wall.
Ensure that nothing can be spilled on, or dropped inside the projector. If this does
happen, switch off and unplug the mains supply immediately. Do not operate the
projector again until it has been checked by qualified service personnel.
Do not insert any metal objects such as a wire or screwdriver into your projector.
Lamp Precautions
Due to the lamp being sealed in a pressurised environment, there is a small risk of
explosion, if not operated correctly. There is minimal risk involved, if the unit is in
proper working order, but if damaged or operated beyond the recommended 1500
hours, the risk of explosion increases.
The projector has a warning system that displays the following message when you
reach 1500 hours of operation - ‘The Lamp has reached the end of its usable life.
Please replace the lamp’. When you see this message please contact your Digital
Projection dealer for a replacement lamp.
If the lamp does explode, it may shatter and pieces of glass could be scattered inside
the lamp housing. In such an event, please contact your dealer.
A—3
Overview
Safety Advice
OVERVIEW
LBV00073; Revision A - 11/01/2002

WARNING: Do not look into the lens while the projector is on. Serious damage to
your eyes could result.
CAUTION: The high pressure lamp may explode if improperly handled. Refer all
servicing to qualified service personnel.
Power Supply
The projector is designed to operate on a power supply of 100-120VAC or 200-
240VAC 50/60Hz. Ensure that your power supply fits this requirement before
attempting to use your projector.
Handle the power cable carefully and avoid excessive bending. A damaged cord can
cause electric shock or fire.
If the projector is not be used for an extended period of time, disconnect the plug
from the power outlet. Do not unplug the power cable from the wall outlet under the
following circumstances, doing so may cause damage to the projector:
a) Immediately after the power cable is plugged into the wall outlet (the POWER
indicator has not changed to a steady amber glow).
b) Immediately after the lamp has been switched off. After the projector is turned
off with the POWER OFF button the cooling fan continues to operate for 1
minute.
c) While the hour glass icon or the message ‘Please wait a moment’ is being
displayed.
A—4
Overview
OVERVIEW
LBV00073; Revision A - 11/01/2002

Installation Advice
The projector should be placed on a flat, level surface and in a dry area free from
dust and moisture and out of direct sunlight. Exposure to direct sunlight, moisture,
smoke or steam could harm internal components.
Do not place the projector in near heaters or heat radiating appliances and ensure
there is adequate ventilation around the projector so heat can dissipate.
The projector should always be handled with care. Dropping or jarring the projector
could damage internal components.
Do not place heavy objects on the projector.
If you wish to have the projector installed on the ceiling do not attempt to install the
projector yourself. The projector must be installed in accordance with any local
building codes by qualified technicians in order to ensure proper operation and
reduce the risk of bodily injury.
The ceiling must be strong enough to support the weight of the projector.
Do not attempt to stack projectors on the ceiling.
Do not use the projector where temperatures vary greatly. The 4000gv projector
must be used at temperatures between 0° to 40°C. The 3000sx projector must be
used at temperatures between 0° to 35°C.
A—5
Overview
OVERVIEW
LBV00073; Revision A - 11/01/2002
✍
✍
✍
✍

Part Names
A—6
Overview
Components
OVERVIEW
LBV00073; Revision A - 11/01/2002
REMOTE 1
PC CONTROL
REMOTE
2
AC IN
SC, TRIGGER
OUT OUT
IN IN
DVI L/MONO
L/MONO
RGB 1
RGB 2
VIDEO 1
VIDEO 2
S-VIDEO AUDIO OUT
R/Cr G/Y B/Cb
VH/HV
MONITOR OUT
R
L/MONO R
L/MONO R L/MONO R
R
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
LENS SHIFT
LEFT
ZOOMFOCUS
UP
DOWN
RIGHT
AUTO
ADJUST
LAMP STATUS POWER
ON/STAND BY
SOURCE
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
LENS SHIFT
LEFT
ZOOMFOCUS
UP
DOWN
RIGHT
AUTO
ADJUST
LAMP STATUS POWER
ON/STAND BY
SOURCE
Lens Hood
Remote Sensor
Left Terminal
Panel
AC Input
Lens
Lens Hood Cap
Right Terminal
Panel
Foot
Built-in
Security Slot
Ventilation Outlet
Remote Sensor
PC Card Slot
(4000gv Only)
Controls
Remote
Sensor
Carrying
Handle
Lamp Cover
Right Speaker
Left Speaker
Remote Sensor
Depression for Foot