Digital Projection 8K Series User manual

Rev A October 2018
INSIGHT Laser 8K Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICK-START GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
119-535A

page i
Digital Projection INSIGHT Laser 8K Series
Rev A October 2018
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the
instructions are closely followed.
LIGHT HAZARD WARNING: this symbol indicates that there is a danger of exposure to intensive light that may result in
personal injury unless the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2018 Digital Projection Ltd. All rights reserved.
Notes

page ii
Digital Projection INSIGHT Laser 8K Series
Rev A October 2018
Laser Information
The outlined section of the product label above provides information about the laser light sources used within the projector.
Caution-useofcontrolsoradjustmentsorperformanceofproceduresotherthanthosespeciedhereinmayresultin
hazardous radiation exposure.
Notes

page iii
Digital Projection INSIGHT Laser 8K Series
Rev A October 2018
Risk Group 3 Information
Light hazard warning
Failure to comply with the following may result in serious injury:
•No direct exposure to the beam is permitted, RG3 IEC 62471-5:2015.
•Operatorscontrolaccesstothebeamwithinthehazarddistanceorinstalltheprojectoratsu󰀩cientheighttoprevent
exposures of spectators’ eyes within the hazard distance.
The hazard distance (Fig. 1) is the distance measured from the projection lens at which the intensity or energy per unit of surface is lower
than the applicable exposure limit on the cornea or skin. If the person is within the hazard distance, the beam is considered unsafe for
exposure.
The hazard distance for this projector is 12m.
Notes
Fig. 1: hazard distance

page iv
Digital Projection INSIGHT Laser 8K Series
Rev A October 2018
Light hazard labels on the body of the projector
Light hazard labelling is part of the product label.
1Product label
2Risk Group 3 label
3Not For Home Use logo
4Hazard Warning symbol
Notes
1 3
4
2

page v
Digital Projection INSIGHT Laser 8K Series
Rev A October 2018
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• 8K (7680 x 4320) resolution up to 60 fps.
• Dual laser light source for long-life low-maintenance operation.
• 16x3G-SDI or 4x12G-SDI input capability.
• Colour management includes Colourmax.
• HDR and HLG management.
• Blanking control for custom input window sizing.
• Built-in web served control application.
• Control via LAN and RS232.
• Motorised lens mount.
A serial number is located on the product label. Record it here:
Notes

page vi
Digital Projection INSIGHT Laser 8K Series
Rev A October 2018
CONTENTS
INSTALLATION AND QUICK-START GUIDE..........................1
CONNECTING THE POWER SUPPLY........................................... 3
PROJECTOR OVERVIEW ............................................................. 4
Front and rear views ............................................................................. 4
Keypad.................................................................................................. 5
Keypad references................................................................................. 5
Keypad indicators .................................................................................. 6
Remote control...................................................................................... 7
POSITIONING THE SCREEN AND PROJECTOR ....................... 10
Tilt ....................................................................................................... 11
ESSENTIAL MAINTENANCE ...................................................... 12
Fitting the lens..................................................................................... 12
Fitting a lens hood............................................................................... 13
Replacing the lters............................................................................. 15
OPERATING THE PROJECTOR ................................................. 16
Switching the projector on................................................................... 16
Switching the projector o󰀨................................................................... 16
Selecting an input signal ..................................................................... 16
Adjusting the lens................................................................................ 17
Orientation ......................................................................................... 17
Picture .............................................................................................. 17
CONNECTION GUIDE..........................................................................18
SIGNAL INPUTS ......................................................................... 20
CONTROL CONNECTIONS......................................................... 21
OPERATING GUIDE ..............................................................................23
MAIN MENU ................................................................................ 25
INPUT MENU .............................................................................. 26
Input Select ......................................................................................... 26
Format Select...................................................................................... 27
Transfer Format .................................................................................. 27
Colour Space ...................................................................................... 28
TEST PATTERN .......................................................................... 29
LENS MENU................................................................................ 30
Lens Lock............................................................................................ 30
Lens Memory ...................................................................................... 31
IMAGE MENU.............................................................................. 32
Gamma SDR / HDR............................................................................ 32
Gain and Lift........................................................................................ 33
COLOR MENU............................................................................. 34
ColorMax............................................................................................. 34
Manual Color Matching ....................................................................... 34
ALIGNMENT MENU .................................................................... 36
Blanking .............................................................................................. 36
LASER MENU ............................................................................. 37
Power Mode........................................................................................ 37
SETUP MENU ............................................................................. 38
ColorMax........................................................................................... 39
Power On/O...................................................................................... 40
OSD Settings...................................................................................... 40
Memory............................................................................................. 41
NETWORK MENU ....................................................................... 42

page vii
Digital Projection INSIGHT Laser 8K Series
Rev A October 2018
INFORMATION MENU................................................................. 43
Input Status......................................................................................... 44
Thermal Status.................................................................................... 44
System Status..................................................................................... 45
Factory Reset...................................................................................... 45
REFERENCE GUIDE..............................................................................46
CHOOSING A LENS.................................................................... 48
Throw Ratios for 8K or 4K-UHD.......................................................... 48
Throw Ratios for 4K ............................................................................ 48
SCREEN REQUIREMENTS......................................................... 49
Fitting the image to the DMD™........................................................... 49
POSITIONING THE IMAGE......................................................... 50
Maximum o󰀨set range......................................................................... 52
Oset for 8K or 4K-UHD ........................................................................ 52
Oset for 4K....................................................................................... 52
ASPECT RATIOS EXPLAINED ................................................... 53
APPENDIX A: LENS PART NUMBERS ....................................... 54
Lens Parts for 8K or 4K-UHD.............................................................. 54
Lens Parts for 4K ................................................................................ 55
APPENDIX C: SUPPORTED SIGNAL INPUT MODES ................ 56
APPENDIX D: WIRING DETAILS ............................................... 57
Signal inputs........................................................................................ 57
3G-SDI or 12G-SDI In, 3G-SDI or 12G-SDI Out........................................... 57
Control connections ............................................................................ 57
LAN ................................................................................................. 57
RS232 .............................................................................................. 57
APPENDIX E: GLOSSARY OF TERMS ....................................... 58
CONTENTS (continued)

Rev A October 2018
INSIGHT Laser 8K Series
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE
4

Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
IN THIS GUIDE
Rev A October 2018
IN THIS GUIDE
Connecting The Power Supply........................................................................ 3
Projector Overview............................................................................................. 4
Front and rear views ...................................................................................................4
Keypad .........................................................................................................................5
Keypad references............................................................................................................ 5
Keypad indicators ............................................................................................................. 6
Remote control............................................................................................................7
Positioning The Screen And Projector....................................................... 10
Tilt...............................................................................................................................11
Essential Maintenance.................................................................................... 12
Fitting the lens...........................................................................................................12
Fitting a lens hood ....................................................................................................13
Replacingthelters..................................................................................................15
Operating The Projector ................................................................................. 16
Switching the projector on.......................................................................................16
Switchingtheprojectoro󰀨.......................................................................................16
Selecting an input signal..........................................................................................16
Adjusting the lens .....................................................................................................17
Orientation ......................................................................................................................17
Picture.............................................................................................................................17

page 3
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Rev A October 2018
Connecting The Power Supply
Rest of the world:
1Firmly push the mains connector into the socket.
USA only:
2Firmly push the mains connector into the socket.
Rotate the connector 20° clockwise to lock it in place
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
2
1

page 4
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2018
Projector Overview
Front and rear views
1Front IR window
2Inputs
3Air inlet
An identical air inlet is located at the bottom of the projector,
right below this one.
4Lens
5Air inlets
6Mains plug with switch and voltage meter
7Keypad
8Air outlet
9Top stacking point
There are four top stacking points: one in each corner.
10 Lifting ring
There are four lifting rings: one in each corner.
11 Rear IR window
12 Air inlet
13 Air inlet
14 Air outlet
15 Adjustable foot
There are four adjustable feet: one in each corner.
16 Bottom stacking point
There are four bottom stacking points: one in each corner.
Notes
The air inlet at the bottom of
the projector can be seen in the
illustration at the beginning of
Positioning The Screen And
Projector further in this guide.
Rear view
9 11 1210
15 1613 14
Front view
4
2 3
85 6
1
7

page 5
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2018
Keypad
Keypad references
1POWER
Switches the projector on and o󰀨 (STANDBY).
2INPUT
Switches to the next input source.
3INFORMATION
Displays .
4TEST PATTERN
Cycles through the test patterns ...O, White, Black, Red, Green, Blue,
CheckerBoard, Grid, ColorBars, Cyan, Yellow, Magenta, Ramp...
5CENTER LENS
Centers the lens.
6PIC MUTE
Switches the laser o󰀨/on.
7MENU
Displays and exits the OSD.
8Arrow buttons & ENTER
Navigation buttons used to highlight menu entries in the OSD.
Press ENTER to open or execute the highlighted menu entry.
9EXIT
Exits the current OSD page and enters the level above.
10 LENS SHIFT arrow buttons
Each of these buttons moves the lens in the specied direction.
11 FOCUS plus and minus buttons
Used to move the focus in and out.
12 ZOOM plus and minus buttons
Used to zoom in and out.
Notes
1 2 3 4 5 6
7 8 9 10 11 12

page 6
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2018
Keypad indicators
1ERROR
A red indicator that shows the following patterns:
O󰀨 = No Error
Single ash followed by a pause = Lamp abnormality
Double ash followed by a pause = Uncovered lamp cover
Triple ash followed by a pause = Fan abnormality
Four ashes followed by a pause = Overheat
A continuous light = System abnormality
2STANDBY
A green indicator that shows a continuous light when standby mode is activated
3RUN
A blue indicator that shows the following patterns:
O󰀨 = Power is o󰀨
Flashing = Projector is cooling down during power o󰀨, or warming up during power on
A continuous light = Power is on
Notes
1
2
3

page 7
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2018
Remote control
1Power ON/OFF
Turns the projector on and o󰀨.
To turn the projector o󰀨, press the OFF button twice within ve seconds.
2Pic Mute OPEN / CLOSE
Shows and hides the projected image.
3OSD ON / OFF
Enables and disables screen timeout messages and showing the OSD during
projection.
4MENU
Access the projector OSD (on-screen display). If the OSD is open, press this button to
go back to the previous menu.
5Navigation (arrows and OK)
Navigate through the menus with the arrows, conrm your choice with OK.
In lens adjustment modes, the arrows are used to move, zoom or focus the lens. See
11 below.
In lens adjustment modes, or when the OSD is not showing, the OK button switches
between modes: Shift Adjustment and Zoom / Focus Adjustment.
6EXIT
Close the current OSD page and return to the level above.
7FREEZE
Freeze the current frame.
8DEFAULT
Restore default settings.
9INFO
Access information about the projector.
10 RE-SYNC
Re-synchronise with the current input signal.
Notes
Not all keys are used on this
projector.
You can use the remote control with
a standard TRS cable connected to
the Wired Remote In connector.
Pic Mute
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
OPEN CLOSE
1
2
5
6
8
4
9
7
3
10

page 8
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2018
Remote control continued
11 LENS adjustment
FOCUS IN / OUT: adjust focus.
SHIFT: press and hold this button, then use the Navigation arrow buttons to move
the lens.
ZOOM IN / OUT: adjust zoom.
12 USER PRESET A, B, C, D
Load user presets.
13 ALT
Press and hold this button to access alternative functions for all buttons with a green
label.
14 DVI / DisplayPort2 / numeric input 3
There is no DVI or DisplayPort2 input on this projector.
15 HDMI 2 / HDMI 4 / numeric input 2
There is no HDMI 2 or HDMI 4 input on this projector.
16 HDMI 1 / HDMI 3 / numeric input 1
There is no HDMI 1 or HDMI 3 input on this projector.
17 TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...O, White, Black, Red, Green, Blue, CheckerBoard, Grid, ColorBars, Cyan,
Yellow, Magenta, Ramp...
Notes
Not all keys are used on this
projector. The unused keys are
grayed out.
You can use the remote control
wirelessly or with a standard TRS
cable connected to the Wired
Remote In connector.
When adjusting focus or zoom,
UP and LEFT will focus/zoom
in, DOWN and RIGHT will zoom
out. When adjusting shift, each
arrow key moves the image in the
corresponding direction.
This projector does not use the
following options on the remote:
HDMI1, HDMI2, HDMI3, HDMI4,
DVI, DisplayPort2, DisplayPort1,
HD-T, SDI, VGA, 3D, COMP 1, EYE
and COMP 2.
Pic Mute
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
HD-T
VGA COMP1 COMP2 TEST
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
OPEN CLOSE
HDMI3 HDMI4
DisplayPort2
DisplayPort1
SDI
13
11
12
14
15
16
17

page 9
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2018
Remote control continued
18 DisplayPort1 /R/ numeric input 4
There is no DisplayPort1 input on this projector.
19 HD-T /G/ numeric input 5
There is no HDBaseT input on this projector.
20 SDI /B/ numeric input 6
There is no SDI input on this projector.
21 VGA /3D/ numeric input 7
There is no VGA input on this projector.
There is no 3D function on this projector.
22 COMP1 /EYE/ numeric input 8
There is no COMP1 input on this projector.
There is no EYE function on this projector.
23 COMP2 /PIP/ numeric input 9
There is no COMP2 input on this projector.
There is no PIP function on this projector.
24 ADDR / ALL
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until the indicator starts ashing.
2. Release this button and while the indicator is still ashing, enter a two-digit
address using the numeric input buttons. The indicator will ash three times
quickly to conrm the change.
To unassign an address and return to the default address 00,
• Press and hold ALT and this button simultaneously until the indicator ashes to
conrm the change.
Notes
Not all keys are used on this
projector. The unused keys are
grayed out.
You can use the remote control
wirelessly or with a standard TRS
cable connected to the Wired
Remote In connector.
This projector does not use the
following options on the remote:
HDMI1, HDMI2, HDMI3, HDMI4,
DVI, DisplayPort2, DisplayPort1,
HD-T, SDI, VGA, 3D, COMP 1, EYE
and COMP 2.
Pic Mute
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
HD-T
VGA COMP1 COMP2 TEST
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
OPEN CLOSE
HDMI3 HDMI4
DisplayPort2
DisplayPort1
SDI
24
19
20
18
21
22
23

page 10
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev A October 2018
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best
position for viewing by your audience.
2. Mount the projector, ensuring that it is at a
suitable distance from the screen for the image
to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the
screen.
The drawings below shows the feet for table
mounting, and the xing holes for ceiling mounting.
Also shown is one of four rings each located in the
top corners. These can be used for lifting a single
projector.
1Four stacking points
2Four adjustable feet
3Four M10 holes for ceiling mount
The screws should not penetrate
more than 18 mm into the body of
the projector.
4Stacking point at the top of the
projector
5Lifting ring (for handling a single
projector)
The rings can be removed to reveal
M10 x 18 deep holes for ceiling
mounting.
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 30
cm (12 in) of space between the
ventilation outlets and any wall,
and 10 cm (4 in) on all other
sides.
Bottom view of the projector Top corner (detail)
1
2
1
1
1
2
2
2
3
3
3
3
4
5

page 11
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev A October 2018
Tilt
The projector can be operated in numerous positions.
It is recommended to position the projector in portrait mode with inputs facing upward, as shown in the diagram:
1Recommended positions, inputs side up
2Also possible
Notes
Pitch
360° 2
330° 2
30° 1
Roll

page 12
Digital Projection INSIGHT Laser 8K Series
Installation and Quick-Start Guide
ESSENTIAL MAINTENANCE
Rev A October 2018
Essential Maintenance
Fitting the lens
1. Insert the lens into the mount.
Engage the three locating studs 1into the corresponding
slots 2on the mount.
2. Rotate the lens clockwise 3until the studs slide all the way
into the slots.
3. Tighten the two xing screws 4on the lens collar.
To remove the lens, reverse the above procedure.
43
21
Notes
Before changing the lens,
always make sure the projector
isswitchedo󰀨andfully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.
The projector will not power on
without the lens tted.
Before turning on the projector,
please ensure the protective caps
are removed from the front and rear
of the lens.
Thetwoxingscrewsmustbe
tightened to at least a torque
of 0.5 N-m using a screwdriver.
Loose screws might lead to the
lensfallingo󰀨.