Digital Projection HIGHlite 660 Series User manual

Rev E November 2012
USER GUIDES
INSTALLATION AND QUICK-START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REFERENCE GUIDE
112-668E
HIGHlite 660 Series
High Brightness Digital Video Projector

Digital Projection HIGHlite 660 Series
Rev E November 2012
About These Guides
Please keep these Guides handy for future reference.
A serial number is located on the back of the projector. Record it here:
Symbols used in these Guides
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2012 Digital Projection Ltd. All rights reserved.
Notes

Rev E November 2012
HIGHlite 660 Series
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE

Digital Projection HIGHlite 660 Series CONTENTS Installation and Quick-Start Guide
Rev E November 2012
CONTENTS
What’s In The Box? ..............................................................................Inst 1
Getting To Know The Projector ..................................................Inst 2
Front and rear views ..............................................................................Inst 2
Remote control.......................................................................................Inst 2
Control panel and indicators.................................................................Inst 3
Positioning The Screen And Projector...................................Inst 4
Fitting The Lens .....................................................................................Inst 5
Operating The Projector ..................................................................Inst 6
Switching the projector on....................................................................Inst 6
Selecting an input signal or test pattern..............................................Inst 6
Input signal.....................................................................................Inst 6
Test pattern ....................................................................................Inst 6
Adjusting the lens ..................................................................................Inst 7
Zoom..............................................................................................Inst 7
Focus .............................................................................................Inst 7
Shift................................................................................................Inst 7
Adjusting the image...............................................................................Inst 7
Orientation and On-Screen Display settings..................................Inst 7
Keystone ........................................................................................Inst 7
Picture............................................................................................Inst 7
Switching the projector off....................................................................Inst 8

Digital Projection HIGHlite 660 Series WHAT’S IN THE BOX? Installation and Quick-Start Guide
Inst 1
Rev E November 2012
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
(105-023)
4x AAA batteries
Power cable, United Kingdom
(102-180)
User Guides on CD
(111-975)
Important Information (111-971)
Power cable, Europe
(102-163)
Power cable, North America
(102-165)
Projector

Digital Projection HIGHlite 660 Series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Inst 2
Rev E November 2012
Getting To Know The Projector
Front and rear views
Notes
The projector uses the standard
Digital Projection infra-red remote
control.
Only the controls shown highlighted
are used on this projector.
For full details of how to use the
controls and the menu system, see
the Operating Guide.
Remote control
Lens
Air
outlet
Front
infra-red
window
Transmit
indicator
Remote
control
backlight
On/Off
40°
40°
Infra-red
reception
Connection
panel
Rear
infra-red
window
Adjustable
feet
Mains
input
Control
panel
Air
inlet

Digital Projection HIGHlite 660 Series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Inst 3
Rev E November 2012
Control panel and indicators
The indicators on the control panel are as follows:
Power off = NO POWER
green = normal RUNNING mode amber = STANDBY mode
Shutter amber = CLOSED green = OPEN
Error off = NO ERROR
ashing = ERROR (temperature) steady = ERROR (voltage)
IR blue ash = Remote control command received
Lamp 1 off = OFF
ashing red = LAMP ERROR green = ON (100%) amber = (85 - 99%)
ashing green = LAMP WARM-UP ashing amber = COOL-DOWN
Lamp 2 off = OFF
ashing red = LAMP ERROR green = ON (100%) amber = (85 - 99%)
ashing green = LAMP WARM-UP ashing amber = COOL-DOWN
Notes
Only the controls shown highlighted
are used on this projector.
For full details of how to use the
controls and the menu system, see
the Operating Guide.

Digital Projection HIGHlite 660 Series POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
Inst 4
Rev E November 2012
Positioning The Screen And Projector
• Install the screen, ensuring that it is in the best position for viewing by your audience.
• Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the sceen.
• The dimension drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling mounting.
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least
30cm (12in) of space between the
ventilation outlets and any wall,
and 10cm (4in) on all other sides.
Do not stack more than 3
projectors.
Do not tilt the projector more than
±12° from side to side when in
use, as this may cause serious
lamp failure, damage the lamp
module and cause extra cost on
replacement.
±12° 360°
All dimensions are in mm.

Digital Projection HIGHlite 660 Series FITTING THE LENS Installation and Quick-Start Guide
Inst 5
Rev E November 2012
Fitting The Lens
• Remove the six screws securing the front cover to the body of the projector.
• Remove the front cover from the projector.
• Push down the lens holder tab.
• Hold down the tab, and insert the lens into the lens aperture, making sure that the plug on the zoom drive mechanism lines up with the
socket on the right of the lens aperture.
• Still holding down the tab, push the lens in rmly as far as it will go.
• Rotate the lens clockwise as far as it will go.
• Release the lens holder tab.
• Replace the front cover and secure it with the six screws.
Fixing
screws
Lens
holder
tab
Socket
Lens
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector

Digital Projection HIGHlite 660 Series OPERATING THE PROJECTOR Installation and Quick-Start Guide
Inst 6
Rev E November 2012
Operating The Projector
Switching the projector on
• Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
• Wait until the self-test has completed and the standby indicator on the projector control panel shows amber. The lamp will be off and the
projector will be in STANDBY mode.
• Press on the remote control or the control panel and hold for 3 seconds, to switch the projector ON. The power indicator on the
control panel will show green, the lamp will light and the shutter will open.
Selecting an input signal or test pattern
Input signal
• Connect an image source to the projector. The signal should be automatically detected by the projector,
and should be displayed within two or three seconds.
If more than one signal is connected, then select the image you want to display:
• Press one of the Input buttons, to on the remote control, or
• Open the On-screen display (OSD) by pressing .
• Select an input signal from the Input Selection menu, using the and buttons.
Test pattern
If you have no image source connected to the projector, then you can display a test pattern instead:
• Open the OSD by pressing .
• Select Test Pattern from the Input Selection menu, using the and buttons.
• Select a pattern from the Test Pattern menu, using the and buttons.
• Close the OSD by pressing again.
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.