Digital Projection INSIGHT 4K Dual LED Series User manual

Rev A October 2017
INSIGHT Dual Laser 4K Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICK-START GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
118-536A

page i
Digital Projection INSIGHT Dual Laser 4K Series
Rev A October 2017
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the
instructions are closely followed.
LIGHT HAZARD WARNING: this symbol indicates that there is a danger of exposure to intensive light that may result in
personal injury unless the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2017 Digital Projection Ltd. All rights reserved.
Notes

page ii
Digital Projection INSIGHT Dual Laser 4K Series
Rev A October 2017
Laser Information
The outlined section of the product label above provides information about the laser light sources used within the projector.
Caution-useofcontrolsoradjustmentsorperformanceofproceduresotherthanthosespeciedhereinmayresultin
hazardous radiation exposure.
Notes
118-790B
IDL
Made in UKGreenside Way, Manchester, UK, M24 1XX
Digital Projection Limited Name of Product : Projector
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions : (1) This device may not cause harmful interference. (2) This device must
accept any interference recieved, including interference that may cause undesired operation.
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.
Complies with 21 CFR 1040.10
and 1040.11 except for
deviations pursuant to
Laser notice No.50,
Dated June 24, 2007
Laser Radiation
Avoid direct eye exposure
Class 3R Laser product
Wave length : 455-470nm
Max output : 330mW
IEC/EN 60825-1:2007
Rayonnement Laser
Èvitez d’exposer directement les yeux
Produit Laser de classe 3R
Longueur d’onde : 455-470nm
Sortie maximale : 330mW
IEC/EN 60825-1:2007
Risk Group 3
Warning!
Do not look into the beam.
No direct eye exposure to the beam is permitted.
RG3 IEC EN 62471-5:2015
Hazard Distance : Refer to Manual
Groupe de Risque 3
Attention!
Ne pas regarder dans le faisceau.
Pas d'exposition directe des yeux au faisceau est autorisée.
RG3 IEC EN 62471-5:2015
Distance de danger : Se reporter au manuel
WARNING
200-240VAC 50/60Hz 20A
MODEL
Part No.
Serial No.
Power
For Oce Use
Isolate mains before removing cover.

page iii
Digital Projection INSIGHT Dual Laser 4K Series
Rev A October 2017
Risk Group 3 Information
Light hazard warning
Failure to comply with the following may result in serious injury:
• No direct exposure to the beam is permitted, RG3 IEC 62471-5:2015.
• Operatorscontrolaccesstothebeamwithinthehazarddistanceorinstalltheprojectoratsufcientheighttoprevent
exposures of spectators’ eyes within the hazard distance.
The hazard distance (Fig. 1) is the distance measured from the projection lens at which the intensity or energy per unit of surface is lower
than the applicable exposure limit on the cornea or skin. If the person is within the hazard distance, the beam is considered unsafe for
exposure.
The table below shows hazard distances for the different lenses used with the projector:
Projection Lens Part Number Hazard Distance
0.93 xed 117-310 4.5 m
1.13 - 1.72 : 1 zoom 115-627 6.2 m
1.65 - 2.60 : 1 zoom 115-630 8.0 m
2.53 - 4.98 : 1 zoom 115-632 9.0 m
Notes
Fig. 1: hazard distance

page iv
Digital Projection INSIGHT Dual Laser 4K Series
Rev A October 2017
Light hazard labels on the body of the projector
Light hazard labelling is part of the product label.
1Product label
2Risk Group 3 label
3Not For Home Use logo
4Hazard Warning symbol
Notes
118-790B
IDL
Made in UKGreenside Way, Manchester, UK, M24 1XX
Digital Projection Limited Name of Product : Projector
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions : (1) This device may not cause harmful interference. (2) This device must
accept any interference recieved, including interference that may cause undesired operation.
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.
Complies with 21 CFR 1040.10
and 1040.11 except for
deviations pursuant to
Laser notice No.50,
Dated June 24, 2007
Laser Radiation
Avoid direct eye exposure
Class 3R Laser product
Wave length : 455-470nm
Max output : 330mW
IEC/EN 60825-1:2007
Rayonnement Laser
Èvitez d’exposer directement les yeux
Produit Laser de classe 3R
Longueur d’onde : 455-470nm
Sortie maximale : 330mW
IEC/EN 60825-1:2007
Risk Group 3
Warning!
Do not look into the beam.
No direct eye exposure to the beam is permitted.
RG3 IEC EN 62471-5:2015
Hazard Distance : Refer to Manual
Groupe de Risque 3
Attention!
Ne pas regarder dans le faisceau.
Pas d'exposition directe des yeux au faisceau est autorisée.
RG3 IEC EN 62471-5:2015
Distance de danger : Se reporter au manuel
WARNING
200-240VAC 50/60Hz 20A
MODEL
Part No.
Serial No.
Power
For Oce Use
Isolate mains before removing cover.
118-790B
IDL
Made in UKGreenside Way, Manchester, UK, M24 1XX
Digital Projection Limited Name of Product : Projector
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions : (1) This device may not cause harmful interference. (2) This device must
accept any interference recieved, including interference that may cause undesired operation.
To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.
Complies with 21 CFR 1040.10
and 1040.11 except for
deviations pursuant to
Laser notice No.50,
Dated June 24, 2007
Laser Radiation
Avoid direct eye exposure
Class 3R Laser product
Wave length : 455-470nm
Max output : 330mW
IEC/EN 60825-1:2007
Rayonnement Laser
Èvitez d’exposer directement les yeux
Produit Laser de classe 3R
Longueur d’onde : 455-470nm
Sortie maximale : 330mW
IEC/EN 60825-1:2007
Risk Group 3
Warning!
Do not look into the beam.
No direct eye exposure to the beam is permitted.
RG3 IEC EN 62471-5:2015
Hazard Distance : Refer to Manual
Groupe de Risque 3
Attention!
Ne pas regarder dans le faisceau.
Pas d'exposition directe des yeux au faisceau est autorisée.
RG3 IEC EN 62471-5:2015
Distance de danger : Se reporter au manuel
WARNING
200-240VAC 50/60Hz 20A
MODEL
Part No.
Serial No.
Power
For Oce Use
Isolate mains before removing cover.
13
4
2

page v
Digital Projection INSIGHT Dual Laser 4K Series
Rev A October 2017
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• 4K resolution up to 60 fps via single DisplayPort input.
• Dual laser light source for long-life low-maintenance operation.
• Dual Pipe input capability (2 x DisplayPort 1.2).
• Full 4K 3D display capability.
• Scaling of HDMI 1.4 formats to 4K resolution.
• Blanking control for custom input window sizing.
• Built-in web served control application.
• Control via LAN and RS232.
• Motorised lens mount.
A serial number is located on the product label. Record it here:
Notes

page vi
Digital Projection INSIGHT Dual Laser 4K Series
Rev A October 2017
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
CONNECTING THE POWER SUPPLY ............................................. 3
PROJECTOR OVERVIEW ............................................................... 4
Front and rear views ............................................................................. 4
Keypad.................................................................................................. 5
Keypad indicators.................................................................................. 6
Laser status lights ................................................................................. 7
Interlock LED status window indicators................................................. 8
Remote control...................................................................................... 9
POSITIONING THE SCREEN AND PROJECTOR........................... 11
Tilt ....................................................................................................... 12
ESSENTIAL MAINTENANCE ........................................................ 13
Fitting the lens..................................................................................... 13
Replacing the lters............................................................................. 14
Monitoring the cooling liquid levels ..................................................... 15
OPERATING THE PROJECTOR.................................................... 16
Switching the projector on................................................................... 16
Switching the projector off................................................................... 16
Selecting an input signal ..................................................................... 17
Calibrating zoom and focus................................................................. 17
Calibrate using the OSD ........................................................................ 17
Calibrate using the remote control............................................................ 17
Calibrate using the keypad ..................................................................... 17
Adjusting the lens................................................................................ 17
Adjusting the image............................................................................. 18
Orientation ......................................................................................... 18
Picture .............................................................................................. 18
CONNECTION GUIDE ............................................................................19
SIGNAL INPUTS .......................................................................... 21
3D Sync............................................................................................... 22
Indicators on the connections panel.................................................... 23
EDID on the HDMI and DisplayPort inputs ......................................... 24
Using HDMI/DisplayPort switchers with the projector .................................... 24
CONTROL CONNECTIONS........................................................... 25
OPERATING GUIDE ................................................................................27
MAIN MENU ................................................................................. 29
LENS MENU................................................................................. 30
Lens Calibrate..................................................................................... 30
Lens Presets ....................................................................................... 31
IMAGE MENU............................................................................... 32
COLOR MENU.............................................................................. 33
GEOMETRY MENU....................................................................... 34
LASER MENU .............................................................................. 35
NETWORK MENU ........................................................................ 36
OSD MENU .................................................................................. 37
Web Served OSD................................................................................ 37
WEB SERVED OSD...................................................................... 38
Access the web served OSD .............................................................. 38
Examples of enhanced functionality on the web served OSD ............ 39
Gamut Editor ...................................................................................... 39
Blanking Editor and Scaling Editor ........................................................... 40

page vii
Digital Projection INSIGHT Dual Laser 4K Series
Rev A October 2017
SYSTEM MENU............................................................................ 41
INFORMATION MENU .................................................................. 42
Laser Information ................................................................................ 43
Network Information............................................................................ 44
OSD Information ................................................................................. 45
OSD Hardware.................................................................................... 45
System Information ............................................................................. 46
UDP logs ........................................................................................... 46
Temperature Information..................................................................... 47
Video Information ................................................................................ 48
REFERENCE GUIDE................................................................................49
THE DMD™.................................................................................. 51
CHOOSING A LENS ..................................................................... 53
SCREEN REQUIREMENTS........................................................... 54
Fitting the image to the DMD™........................................................... 54
Diagonal screen sizes......................................................................... 55
Fitting the image to the screen............................................................ 56
Positioning the screen and projector................................................... 57
POSITIONING THE IMAGE........................................................... 58
Maximum offset range......................................................................... 60
ASPECT RATIOS EXPLAINED...................................................... 61
APPENDIX A: LENS PART NUMBERS.......................................... 62
APPENDIX B: LENS CHARTS ...................................................... 63
How to use the lens charts.................................................................. 63
Lens chart, up to 100 m throw............................................................. 64
Lens chart, 10 m throw in detail .......................................................... 65
APPENDIX C: SUPPORTED SIGNAL INPUT MODES .................... 66
APPENDIX D: WIRING DETAILS .................................................. 68
Signal inputs - main connections panel............................................... 68
HDMI................................................................................................ 68
DisplayPort ........................................................................................ 69
Control connections ............................................................................ 70
LAN ................................................................................................. 70
RS232 .............................................................................................. 70
3D Sync IN and 3D Sync OUT ................................................................ 70
APPENDIX E: GLOSSARY OF TERMS.......................................... 71
TECHNICAL SPECIFICATIONS .................................................... 80
Models................................................................................................. 80
Inputs and outputs............................................................................... 80
Bandwidth ........................................................................................... 80
Remote control and keypad ................................................................ 80
Automation control .............................................................................. 81
Color temperature ............................................................................... 81
Lenses................................................................................................. 81
Lens mount ......................................................................................... 81
Mechanical mounting .......................................................................... 81
Orientation........................................................................................... 81
Electrical and physical specications.................................................. 82
Safety & EMC regulations................................................................... 82
CONTENTS (continued)

Rev A October 2017
INSIGHT Dual Laser 4K Series
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE
4

Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
IN THIS GUIDE
Rev A October 2017
IN THIS GUIDE
Connecting The Power Supply........................................................................ 3
Projector Overview............................................................................................. 4
Front and rear views ...................................................................................................4
Keypad .........................................................................................................................5
Keypad indicators .......................................................................................................6
Laser status lights ......................................................................................................7
Interlock LED status window indicators ...................................................................8
Remote control............................................................................................................9
Positioning The Screen And Projector....................................................... 11
Tilt...............................................................................................................................12
Essential Maintenance.................................................................................... 13
Fitting the lens...........................................................................................................13
Replacingthelters..................................................................................................14
Monitoring the cooling liquid levels........................................................................15
Operating The Projector ................................................................................. 16
Switching the projector on.......................................................................................16
Switching the projector off.......................................................................................16
Selecting an input signal..........................................................................................17
Calibrating zoom and focus .....................................................................................17
Calibrate using the OSD .................................................................................................17
Calibrate using the remote control ..................................................................................17
Calibrate using the keypad .............................................................................................17
Adjusting the lens .....................................................................................................17
Adjusting the image..................................................................................................18
Orientation ......................................................................................................................18
Picture.............................................................................................................................18

page 3
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Rev A October 2017
Connecting The Power Supply
Firmly push the mains connector into the socket 1, then press the ON/OFF switch 2.
A digital meter shows the value of the connected line voltage.
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
1
2

page 4
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2017
Projector Overview
Front and rear views
1Front IR window
2Inputs
3Air inlet
An identical air inlet is located at the bottom of the projector,
right below this one.
4Lens
5Air inlets
6Mains plug with switch and voltage meter
7Keypad
8Interlock LED status window
9Air outlet
10 Top stacking point
There are four top stacking points: one in each corner.
11 Lifting ring
There are four lifting rings: one in each corner.
12 Rear IR window
13 Air inlet
14 Air inlet
15 Air outlet
16 Adjustable foot
There are four adjustable feet: one in each corner.
17 Bottom stacking point
There are four bottom stacking points: one in each corner.
Notes
The air inlet at the bottom of
the projector can be seen in the
illustration at the beginning of
Positioning The Screen And
Projector further in this guide.
Rear view
10 12 1311
16 1714 15
Front view
4
2 3
985 6
1
7

page 5
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2017
Keypad
1POWER ON/OFF (with indicator)
2FOCUS
Use with the arrow keys to adjust focus.
Press to enter FOCUS ADJUSTMENT mode, then press an arrow key to
focus the image.
To exit FOCUS ADJUSTMENT mode, press EXIT or wait 10 seconds.
3SHIFT
Use with the arrow keys to move the projected image.
Press to enter SHIFT ADJUSTMENT mode, then press an arrow key to
move the image.
To exit SHIFT ADJUSTMENT mode, press EXIT or wait 10 seconds.
4ZOOM
Use with the arrow keys to zoom the image in or out.
Press to enter ZOOM ADJUSTMENT mode, then press an arrow key to
zoom the image.
To exit ZOOM ADJUSTMENT mode, press EXIT or wait 10 seconds.
5Arrow keys
Use with FOCUS, SHIFT and ZOOM to make adjustments.
6EXIT
Use to exit lens adjustment modes.
7SHUTTER OPEN/CLOSE (with indicator)
8RPY
Press, then press RIGHT to calibrate zoom.
Press, then press LEFT to calibrate focus.
9INPUT +
Switches to the next available input source. Cycle through the inputs in
the following order:
...HDMI A, HDMI B, DisplayPort A, DisplayPort B...
10 INPUT –
Switches to the previous available input source. Cycle through the
inputs in the following order:
...DisplayPort B, DisplayPort A, HDMI B, HDMI A...
Notes
See Entering alphanumeric values
in the Operating Guide.
CTRL FOCUS
AUTO INFO SHIFT ZOOM
MENU INPUT
OK
EXIT INPUT
OFF
ON
OSD
ON
OFF
POWER
OPEN
CLOSE
SHUTTER
+
–
RPY
1
5
10
3
4
2
9
7
8
6

page 6
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2017
Keypad indicators
1POWER
Behavior Meaning
Off The projector is switched off.
On (amber) The projector is in Standby mode.
On (green) The projector is switched on
(Normal mode).
2SHUTTER
Behavior Meaning
On (amber) The shutter is closed.
On (green) The shutter is open.
Notes
CTRL FOCUS
AUTO INFO SHIFT ZOOM
MENU INPUT
OK
EXIT INPUT
OFF
ON
OSD
ON
OFF
POWER
OPEN
CLOSE
SHUTTER
+
–
RPY
1 2

page 7
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2017
Laser status lights
1Lamp 1 and 2 indicators
These indicators correspond to the two laser light sources within the projector.
(Lamp 3 and 4 remain switched off.)
Behavior Meaning
Off The laser light source is switched off.
On (green) The laser light source is switched on (100%).
On (amber) The laser light source is switched on (30-99%).
Flashing (red) Light Source Error
2Error indicator
Behavior Meaning
On (red) Error
Flashing Error
3Infrared indicator
Behavior Meaning
Flashing (blue) The projector is receiving input from the remote control.
LAN
注 意 ：通 风 口 — — 请 勿 堵 塞
Air exit - Do not block
3
1
4
2
IN OUT
LAMP SERIAL ERROR WIRED REMOTE
IN OUT
IN OUT AB A B A B
1 2 3
Notes

page 8
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2017
Interlock LED status window indicators
The interlock LED status window 1shows whether an interlock switch has been activated.
Each LED signals a problem with closing or attaching the following:
Lens
Front cover
Left cover
Top cover
Right cover
Rear cover
Notes
The exact location of each
interlock switch can be found in the
Important Information document.
STATUS
1

page 9
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2017
Remote control
The remote control is shipped with no battery tted. Remove the back cover and insert the
supplied cells while observing the correct cell polarity.
1Transmit indicator
Flashes when the remote sends a signal to the projector. Lights solidly when the
projector is in FOCUS, ZOOM or SHIFT ADJUSTMENT mode.
2Power ON / OFF
3Shutter OPEN / CLOSE
4MENU
Display / exit the OSD.
5Arrow keys and OK
Use the arrow keys to navigate through the menus, conrm your choice with OK.
When the OSD is not showing, use the arrows to focus, zoom and shift the lens.
6EXIT
Exit lens adjustment modes or exit the OSD.
7FOCUS
Press for FOCUS ADJUSTMENT mode, use the arrows to make the adjustment.
8CAL
Press and hold this key, then press FOCUS or ZOOM to calibrate focus or zoom
respectively.
9ZOOM
Press to enter ZOOM ADJUSTMENT mode, then use the arrow keys to make the
adjustment.
10 SHIFT
Press to enter SHIFT ADJUSTMENT mode, then use the arrow keys to make the
adjustment.
Notes
Not all keys are used on this
projector. The unused keys are
grayed out.
You can use the remote control
wirelessly or with a standard TRS
cable connected to the Wired
Remote In connector.
 Whenanewlensistted,a
calibration procedure must be
carried out.
 Whenadjustingfocusorzoom,
UP and LEFT will focus/zoom
in,DOWNandRIGHTwillzoom
out.Whenadjustingshift,each
arrow key moves the image in the
corresponding direction.
WhenyouenterFOCUS,ZOOM
orSHIFTADJUSTMENTmode,
all other remote control functions
become unavailable. To cancel an
adjustmentmode,eitherpressEXIT
or wait ten seconds.
VGA HDMI DVI 3GSDI
CVBS1 SVIDEO
CLOSE
12 3 4
COMP CVBS2
5 6 7 8
9 0 10+ #
MAIN SUB DUAL HD-T
OFF ON
ALT ROLL
PITCH YAW
FOCUS CAL
SHIFT ZOOM
EYE
SWAP
MAIN/PIP
SWAP
BRI CON GAMMA 3D
ON/OFF
PIP
ON/OFF
LOAD SAVE TEST ADDR
BACKLIGHT
RGB
PRESET
SHUTTER
OPEN
POWER
MENU
OK
EXIT INFO
8
10
9
1
2
3
5
4
6
7

page 10
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A October 2017
Remote control continued
11 Number keys for input selection and lens presets
Select input source. Press:
1 for HDMI A, 2 for HDMI B, 3 for DisplayPort A, 4for DisplayPort B, 7for Dual Pipe LR
and 8for Dual Pipe EW.
Use numbers 1to 5with the PRESET keys to load and save lens presets. (See 15
below.)
12 GAMMA
Access the gamma control.
13 BRI
Access the brightness control.
14 CON
Access the contrast control.
15 PRESET keys
Press and hold LOAD or SAVE, then press a number key 1to 5to load or save a lens
preset.
16 Remote control backlight ON / OFF
Make the remote control keys glow in the dark, or switch this feature off.
17 INFO
Press to display the IP address of the projector.
18 3D ON/OFF
Enable and disable 3D.
Notes
Not all keys are used on this
projector. The unused keys are
grayed out.
You can use the remote control
wirelessly or with a standard TRS
cable connected to the Wired
Remote In connector.
VGA HDMI DVI 3GSDI
CVBS1 SVIDEO
CLOSE
12 3 4
COMP CVBS2
5 6 7 8
9 0 10+ #
MAIN SUB DUAL HD-T
OFF ON
ALT ROLL
PITCH YAW
FOCUS CAL
SHIFT ZOOM
EYE
SWAP
MAIN/PIP
SWAP
BRI CON GAMMA 3D
ON/OFF
PIP
ON/OFF
LOAD SAVE TEST ADDR
BACKLIGHT
RGB
PRESET
SHUTTER
OPEN
POWER
MENU
OK
EXIT INFO 17
11
16
13
15
12
14
18

page 11
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev A October 2017
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best
position for viewing by your audience.
2. Mount the projector, ensuring that it is at a
suitable distance from the screen for the image
to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the
screen.
The drawings below shows the feet for table
mounting, and the xing holes for ceiling mounting.
Also shown is one of four rings each located in the
top corners. These can be used for lifting a single
projector.
1Four stacking points
2Four adjustable feet
3Four M10 holes for ceiling mount
The screws should not penetrate
more than 18 mm into the body of
the projector.
4Stacking point at the top of the
projector
5Lifting ring (for handling a single
projector)
The rings can be removed to reveal
M10 x 18 deep holes for ceiling
mounting.
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 30
cm (12 in) of space between the
ventilation outlets and any wall,
and 10 cm (4 in) on all other
sides.
Bottom view of the projector Top corner (detail)
1
2
1
1
1
2
2
2
3
3
3
3
4
5

page 12
Digital Projection INSIGHT Dual Laser 4K Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev A October 2017
Tilt
The projector can be operated in numerous positions.
It is recommended to position the projector in portrait mode with inputs facing upward, as shown in the diagram:
1Recommended positions, inputs side up
2Also possible
Notes
Pitch
360° 2
330° 2
30° 1
Roll