Digital Projection Titan Pro Series III User manual

Rev A May 2012
USER GUIDES
INSTALLATION AND QUICK-START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
112-884A
Titan Pro series III
High Brightness Digital Video Projector
BOOK CONTENTS
About these Guides
Symbols used in these guides
Warnings
Notes
Product revision

Digital Projection Titan Pro series III ABOUT THESE GUIDES
Rev A May 2012
About these Guides
Please read this guide carefully before using the projector, and keep it handy for future reference.
A serial number is located on the back of the projector. Record it here:
Symbols used in these guides
Warnings
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
Notes
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specifications and designs, and add new features
without prior notice. Projectors built prior to this revision of the Operating Guide may therefore not include all the features described.

Rev A May 2012
Titan Pro series III
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE
BOOK CONTENTS
INSTALLATION AND QUICK-
START GUIDE
What’s in the Box?
Getting to Know the Projector
Front and rear views
Control panel
Remote control
Connection panel indicators

Digital Projection Titan Pro series III CONTENTS Installation and Quick-Start Guide
Rev A May 2012
CONTENTS
What’s in the Box?...............................................................................Inst_1
Getting to Know the Projector....................................................Inst_2
Front and rear views .............................................................................Inst_2
Control panel .........................................................................................Inst_3
Remote control......................................................................................Inst_3
Connection panel indicators................................................................Inst_4
Positioning the Screen and Projector....................................Inst_5
Tilting the Projector ..............................................................................Inst_5
Chassis adjustment ..............................................................................Inst_5
Fitting and adjusting the optional Rigging Frame .............................Inst_6
Fitting ............................................................................................Inst_6
Stacking ........................................................................................Inst_6
Pitch, Roll and Yaw .......................................................................Inst_6
Redirecting the Air Outlet Duct............................................................Inst_7
Fitting the Lens .....................................................................................Inst_8
Lens Calibration ....................................................................................Inst_8
Operating the Projector...................................................................Inst_9
Switching the Projector On ..................................................................Inst_9
Selecting an Input Signal or Test Pattern ...........................................Inst_9
Input signal....................................................................................Inst_9
Test pattern ...................................................................................Inst_9
Adjusting the Lens..............................................................................Inst_10
Zoom...........................................................................................Inst_10
Focus ..........................................................................................Inst_10
Shift.............................................................................................Inst_10
Adjusting the Image............................................................................Inst_10
Orientation...................................................................................Inst_10
Control settings ...........................................................................Inst_10
Keystone .....................................................................................Inst_10
Picture.........................................................................................Inst_10
Switching the Projector Off................................................................ Inst_11

Digital Projection Titan Pro series III WHAT'S IN THE BOX? Installation and Quick-Start Guide
Page Inst_1Rev A May 2012
What’s in the Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your Projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
(105-023)
4x AAA batteries
User Guides on CD
(112-889) Important Information
(112-888)
Power cable, United Kingdom
(112-000)
Power cable, Europe
(112-001)
Power cable, North America
(112-002)
Projector
Remote cable
(102-162)

Digital Projection Titan Pro series III GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Page Inst_2Rev A May 2012
Getting to Know the Projector
Front and rear views
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.
Lens
Air outlet
duct
Top
air inlets
Side
Connection
panel
Mains
input
Control
panel
Adjustable
feet
Front
infra-red
window
Rear
infra-red window
Rear
Connection panel
Bottom
air inlets
Lens release
lever
Lens
motor

Digital Projection Titan Pro series III GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Page Inst_3Rev A May 2012
Notes
The projector uses the standard
Digital Projection infra-red remote
control.
Only the controls shown highlighted
are used on this projector.
For full details of how to use the
controls and the menu system, see
the Operating Guide.
Each time a lens is fitted to
the projector, the calibration
procedure must be carried out.
(see the Fitting the Lens)
Control panel
The indicators on the control panel are as follows:
Power off = NO POWER
green = normal RUNNING mode amber = STANDBY mode
Shutter amber = CLOSED green = OPEN
Infra-red
reception
40°
40°
Transmit
indicator
Remote
control
backlight
On/Off
Remote control
Power Shutter (RPY) Lens
calibration
See Fitting the
Lens.
Menu
controls
Input selection
1–10 selects Inputs 1 to 10
#selects Dual Pipe (inputs 9+10)
Image adjustment
Brightness, Contrast and Saturation
use and to adjust sliders
Lens controls

Digital Projection Titan Pro series III GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Page Inst_4Rev A May 2012
Connection panel indicators
The indicators on the rear connection panel are as follows:
All on = Power-On Self Test
Lamps 1,2 off = OFF
green = ON (100%) amber = 85-99% (on some models)
flashing green = WARM-UP flashing amber = COOL-DOWN
red (projector in standby) = Lamp Comms Error (call service)
red (projector on) = Ballast Comms Error (call service)
flashing red (projector in standby) = Lamp Error on previous operation
flashing red (projector on) = Lamp / Interlock Error
Error flashing = Fan / System Error steady = Voltage Error
IR blue flash = Remote control command received
Inputs The indicators next to the input connectors on both panels are as follows:
off = not selected
green = input selected, signal detected, and in range
flashing green = input selected, but signal not detected or out of range
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.
For more information about
the connection panels, see the
Connection Guide.
Lamps
1 2
Error
IR
Rear Connection Panel Side Connection Panel

Digital Projection Titan Pro series III POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
Page Inst_5Rev A May 2012
Notes
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
Ensure that there is at least
30cm (12in) of space between the
ventilation outlets and any wall,
and 10cm (4in) on all other sides.
Do not place the projector with its
front panel down on a surface, as
this may damage the lens or the
lens release lever.
Positioning the Screen and Projector
Install the screen, ensuring that it is in the best position for viewing by your audience.
Position the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen.
Tilting the Projector
Do not tilt the projector more than is shown in the tilt diagrams, when in use, as this may cause serious lamp failure, damage the
lamp module and cause extra cost on replacement.
•
•
Chassis adjustment
If the projector is to be operated from a flat surface such as a projector table, then
adjustment of projector level should be made by turning the four feet under the chassis.
Set the adjustable feet so that the projector is level, and perpendicular to the sceen.
•
±10° ±10°
180°
±10°
±10°
180°
SX+ 660
1080p 660
WUXGA 660
SX+ 3D-P
1080p 3D-P
WUXGA 3D-P
SX+ 3D-L
1080p 3D-L
WUXGA 3D-L

Digital Projection Titan Pro series III POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
Page Inst_6Rev A May 2012
Fitting and adjusting the optional Rigging Frame
Fitting
Remove the four adjustable feet.
Secure the rigging frame to the projector, as shown, making sure that the male frame
couplings are at the top. Secure each adaptor plate to the projector (three screws), and
secure each of the adjuster brackets to an adaptor plate (three screws).
Stacking
The projectors can be stacked on top of each other, or suspended below each other.
Carefully lower each projector down onto the top of the others, making sure that all four
frame couplings engage fully.
Fit a locking pin into each coupling. A ball in the end of the pin prevents the pin from
falling out – to insert or remove a locking pin, press the button on the end of the pin to
release the ball.
Pitch, Roll and Yaw
To adjust the pitch, turn either the front pair or the rear pair of vertical adjusters, taking
care to turn both adjusters by the same amount.
To adjust the roll, turn either the left pair or the right pair of vertical adjusters, taking care
to turn both adjusters by the same amount.
To adjust the yaw, turn the single horizontal adjuster at the front.
•
•
•
•
•
•
•
Notes
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
Do not place the projector with its
front panel down on a surface, as
this may damage the lens or the
lens release lever.
Do not stack more than 3
projectors.
Do not place heavy objects on top
of the projector chassis. Only the
chassis corners and the rigging
frame are capable of withstanding
the weight of another projector.
Backup safety chains or wires
should always be used with
ceiling mount installations.
Fixing
screws
(2 x 3)
Horizontal
adjuster
Vertical
adjusters
Frame
couplings
Pitch Roll Yaw
Locking
pin