Digital Projection M-Vision Cine 230 User manual

Rev E July 2014
M-Vision Cine 230, Cine 260 HB, HC
M-Vision Cine 400
High Brightness Digital Video Projector
16:9 widescreen display
User Manual
111-260E

Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual
Declaration of Conformity
Directives covered by this Declaration
2004/108/EC Electromagnetic Compatibility Directive.
2006/95/EC Low Voltage Equipment Directive.
Products covered by this Declaration
Large screen video projector type The CE mark was rst applied in:
M-Vision Cine 230 October 2010
M-Vision Cine 260 HB, HC May 2010
M-Vision Cine 400 October 2010
Basis on which Conformity is being declared
The products identied above comply with the protection requirements of the above EU directives, and the
manufacturer has applied the following standards.
EN 55022:1998 - Limits and Methods of Measurement of Radio Disturbance Characteristics of Information
Technology Equipment.
EN 55024:1998 - Limits and Methods of Measurement of Immunity Characteristics of Information Technology
Equipment.
EN 60950-1:2001 - Specication for Safety of Information Technology Equipment, including Electrical Business
equipment.
The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage
directive has been compiled by the signatory below and is available for inspection by the relevant enforcement
authorities.
Signed:
Authority: D.J. Quinn, Product Development Director
Date: 15 October 2010
Attention!
The attention of the specier, purchaser, installer, or user is drawn to special measures and limitations to use which
must be observed when these products are taken into service to maintain compliance with the above directives.
Details of these special measures are available on request, and are also contained in the product manuals.

Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Rev E July 2014 Page v
Please read this user manual carefully before using the projector, and keep
the manual handy for future reference.
A serial number is located on the back of the projector. Record it here:
Symbols used in this guide
Warnings
ELECTRICAL WARNING: this symbol indicates that there is a danger of
electrical shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical
injury to yourself and/or damage to the equipment unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that
you should read.
Trademarks
• IBM is a registered trademark of International Business Machines Corporation.
• Macintosh and PowerBook are registered trademarks of Apple Computer, Inc.
• Other product and company names mentioned in this user’s manual may be the
trademarks of their respective holders.
Product revision
• Because we at Digital Projection continually strive to improve our products, we
may change specications and designs, and add new features without prior
notice. Projectors built prior to this revision of the User Manual may therefore not
include all the features described.
Manual revision
Date Description Revision
December 2010 Rev A
August 2011 Brilliant Color claried Rev B
Important Information

Page vi Rev E July 2014
Important Information Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual
General precautions
Do not open the cabinet. There are no user serviceable parts inside.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this
equipment MUST be earthed.
Take care to prevent small objects such as paper or wire from falling
into the projector. If this does happen, switch off immediately, and have
the objects removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any
liquids on top of the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a
damaged power cable.
There are no user-serviceable parts inside the lamp module. The whole
module should be replaced.
Only lamps supplied by Digital Projection and intended for this
projector should be used. Fitting any other lamp could damage both
projector and lamp, and will invalidate the warranty.
Take care when removing the lamp module.
 NEVERtouchthelamporreector.
Take care not to touch the glass surface of the lamp module. If you
do accidentally touch the glass, it should be cleaned before use. (see
section 5. Maintenance.)
Do not use the lamp for more than 2000 hours, as this may cause
serious lamp failure, damage the lamp module and cause extra cost on
replacement.
HID lamps produce high intensity light. Do not look directly at the light
coming from the lamp housing, or the lens, or allow items such as
magnifying lenses to be placed in the light path. This could result in
serious eye damage.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could
causeare
Always allow the projector to cool for 5 minutes before disconnecting
the power, moving the projector or changing the lamp.
Never use strong detergents or solvents such as alcohol or thinners to
clean the projector and lens.
Notes

Rev E July 2014 Page vii
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual Important Information
Installation precautions
Theprojectormustbeinstalledonlybysuitablyqualiedpersonnel,in
accordance with local building codes.
The projector should be installed as close to the power outlet as
possible.
The power connection should be easily accessible, so that it can be
disconnected in an emergency.
Ensure that there is at least 30cm (12in) of space between the
ventilation outlets and any wall, and 10cm (4in) on all other sides.
Do not install the projector close to anything that might be affected by
its operational heat, for instance, polystyrene ceiling tiles, curtains etc.
The projector weighs approximately 13 kg (29 lbs). Use safe handling
techniques when lifting the projector.
Do not stack more than three projectors.
When stacking projectors, the stack MUST be vertical, to ensure that
the stresses are distributed to all four chassis corners.
Before installation, make sure that the surface, ceiling or rigging that is
to support the projector is capable of supporting the combined weight
of all the projectors.
Backup safety chains or wires should always be used with ceiling
mount installations.
Do not place heavy objects on top of the projector chassis. Only the
chassis corners are capable of withstanding the weight of another
projector.
Do not drop or knock the projector.
Place the projector in a dry area away from sources of dust, moisture,
steam, smoke, sunlight or heat.
Do not tilt the projector more than ±12° in either direction when in use,
as this may cause serious lamp failure, damage the lamp module and
cause extra cost on replacement.
Cine 400 may be tilted to one side and positioned in portrait mode as
long as the exhaust outlet points upward.
When positioning the Cine 400 projector in portrait mode, ensure
adequateairowtotheairinlet.
Operationandcongurationprecautions
Software update should NOT be carried out except by, or with the
supervision of, Digital Projection Service personnel.
Notes
±12°
±12°

Page viii Rev E July 2014
Important Information Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual
Notes
Compliance with international standards
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 35 dB (A) according to ISO 3744 or ISO 7779.
RF Interference
FCC
The Federal Communications Commission does not allow any modications or
changes to the unit EXCEPT those specied by Digital Projection in this manual.
Failure to comply with this government regulation could void your right to operate
this equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant with Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a residential environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
European Waste Electrical and Electronic Equipment
(WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and
Electronic Equipment. Our products are designed with reuse, recycling
and recovery of all components in mind. To this end, at end of life, your
projector may be returned to Digital Projection Ltd or its agent so that the
environmental impact can be minimised.

Rev E July 2014 Page ix
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual Important Information
Digital Projection Contact details
Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Ofce: as above
Tel [phone]
Fax [phone]
Email [email protected], [email protected]
Web Site www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel (USA) 770 420 1350
Fax (USA) 770 420 1360
Email [email protected]
Web Site www.digitalprojection.com
Notes

Page x Rev E July 2014
Important Information Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual