Digital Projection M-Vision 1080p-260 series User manual

Rev A May 2010
Lamp cover
Rear Infra-red
window (remote
control)
Power
connection
Lens
Front Infra-red
window
(remote control)
Air inlet
Air outlet
Focus ring
Zoom ring
Horizontal shift
adjustment
Vertical shift
adjustment
(under the
badge)
Input
connections
Adjustable feet Projector control
panel
M-Vision 1080p-260
GETTING STARTED
Getting to know the projector
Notes
For complete and detailed
information about how to use
and control the projector, see
the User Manual.
110-286A
40°
40°
Remote
reception
angle
Remote
control

Page 2 Rev A May 2010
Getting Started Digital Projection M-Vision 1080p-260 User Manual
Switching the projector on
Connect the power cable between the mains supply and the projector.
Wait until the self-test has completed and the standby indicator on the projector
control panel shows amber. The lamp will be off and the projector will be in
STANDBY mode.
Press POWER ON on the remote control or POWER on the projector
control panel to switch the projector ON. The power indicator on the control
panel will ash blue for approximately 30 seconds, whilst the lamp comes up to
full brightness. When the projector is ready for use, the power indicator will show
a steady blue.
•
•
Notes
For more information about
positioning the screen and
projector, see Positioning
the screen and projector, in
section 2. of the User Manual:
Installation.
For more detailed information
about:
- using the control keys on the
remote control or the projector
control panel,
- using the menus,
see section 4. of the User
Manual: Controlling the
projector.
If the red ISSUE indicator is
illuminated continuously or
ashing, see Error Codes in
section 6 of the User Manual:
Appendix, for more information
Do not mix an old battery with
a new one or different types of
batteries.
If you will not use the remote
control for a long time, remove
the batteries to avoid damage
from battery leakage.
Inserting batteries into the remote control
Open the battery compartment and insert two AA size batteries, making sure
they are inserted the correct way round, as shown below.
•
Positioning the screen and projector
Install the screen, ensuring that it is in the best position for viewing by your
audience.
Mount the projector, ensuring that it is at a suitable distance from the screen for
the image to ll the screen, and that it is perpendicular to the sceen.
•
•
Power
connection
Projector
control panel

Rev A May 2010 Page 3
Digital Projection M-Vision 1080p-260 User Manual Getting Started
Selecting an input signal or test pattern
Input
Connect an video source to the projector. The signal should be automatically
detected by the projector, and should be displayed within a two or three
seconds.
If more than one signal is connected to the projector, then select which signal
is to be displayed, using the to buttons on the remote control, or
by pressing the SOURCE button on the projector control panel until the correct
signal is displayed.
Test pattern
If you have no video source connected to the projector, then you can display a test
pattern as follows:
Press on the remote control, until the desired test pattern is displayed.
•
•
•
Notes
For more information about
connecting input signals, see
Signal Inputs, in section 2. of
the User Manual: Installation.
For more detailed information
about input connections, see
Input signals in section 6. of
the User Manual: Controlling
the projector.
For more information about lens
shift, see Shifting the image in
section 2. of the User Manual:
Installation.
Adjusting the lens
Zoom
Turn the smooth ring on the lens, closest to the case, to adjust the zoom so that
the image lls the screen.
Focus
Turn the knurled ring at the outer end of the lens, to adjust the focus until the
image is sharp.
Shift
Rotate the Digital Projection badge on top of the projector to reveal the shift
adjustment access holes. Use the 5mm allen wrench to adjust the horizontal and
vertical position of the image.
•
•
•
Horizontal shift
adjustment
Vertical shift
adjustment
(Rotate the
badge)
Focus ring
Zoom ring

Page 4 Rev A May 2010
Getting Started Digital Projection M-Vision 1080p-260 User Manual
Adjusting the projected image
Aspect ratio
Press on the remote control until the image is displayed in the corect aspect
ratio.
Image quality settings
Press any of the following keys on the remote control, followed by and , to
adjust these image quality settings:
Brightness
Contrast
Sharpness
•
•
Notes
For more detailed information
about:
- using all the control keys
on the remote control or the
projector control panel,
- using the menus,
see section 4. of the User
Manual: Controlling the
projector.
For the picture setting
adjustments shown here:
- after 5 seconds, if no
adjustment has been made,
the indicator will go out and
the adjustment key must be
pressed again.
- to end the adjustment before
5 seconds has elapsed, press
a different adjustment key, or
press the key again.
Always allow the lamp to cool
for 5 minutes before:
- moving the projector
- changing the lamp
Switching the projector off
Press POWER OFF on the remote control or POWER on the
projector control panel, then press the button a second time to conrm your
intention to switch off.
The lamp will switch off, and the power indicator on the control panel will ash
blue for approximately 30 seconds until the lamp has cooled down.
Wait until the power indicator has switched off and the standby indicator on the
projector control panel shows amber. The projector will now be in STANDBY
mode.
Disconnect the power cable from the projector.
•
•
•