Digital Projection MERCURY 5000gv User manual

MERCURY 5000gv
DMD Projector
User’s Manual

ii

Digital Projection MERCURY 5000gv
Declaration of Conformity
Directives covered by this Declaration
89/336/EECElectromagneticCompatibilityDirective,amendedby92/31/EECand93/68/EEC.
73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC.
Products covered by this Directive
Large Screen Projector type MERCURY 5000gv
Basis on which Conformity is being declared
The products identified above comply with the protection requirements of the above EU directives, and the
manufacturer has applied the following standards.
EN 50081-1:1992 - EMC Generic Emission Standard for Residential, Commercial and Light Industrial Equipment.
EN 50082-1:1992 - EMC Generic Immunity Standard for Residential, Commercial and Light Industrial Equipment.
EN 55022:1995 - Limits and Methods of Measurement of Radio Disturbance Characteristics of Information Technology
Equipment.
EN 60950:1992 - Specification for Safety of Information Technology Equipment, including Electrical Business equipment.
The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage
directive has been compiled by the signatory below and is available for inspection by the relevant enforcement
authorities. The CE mark was first applied in 2004.
Signed:
Authority: D.J. Quinn, Director - Product Development
Date: 26February 2004
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations to use which
must be observed when these products are taken into service to maintain compliance with the above directives.
Details of these special measures are available on request, and are also contained in the product manuals.
iii

iv
Important Information Digital Projection MERCURY 5000gv
Precautions
Please read this manual carefully before using your Digital
Projection MERCURY 5000gv Projector and keep the manual
handy for future reference.
Your serial number is located on the side of your projector.
Record it here:
CAUTION
To turn off main power, be sure to remove the
plug from power outlet.
The power outlet socket should be installed as
near to the equipment as possible, and should
be easily accessible.
CAUTION
TOPREVENTSHOCK,DONOTOPENTHE
CABINET.
NOUSER-SERVICEABLEPARTSINSIDE.
REFERSERVICINGTOQUALIFIEDDigital
ProjectionSERVICEPERSONNEL.
This symbol warns the user that uninsulated
voltage within the unit may be sufficient to
cause electrical shock. Therefore, it is
dangerous to make any kind of contact with any
part inside of the unit.
This symbol alerts the user that important
information concerning the operation and
maintenance of this unit has been provided. The
information should be read carefully to avoid
problems.
WARNING
TOPREVENTFIREORSHOCK,DONOTEXPOSETHISUNIT
TORAINORMOISTURE.
DONOTUSETHISUNIT’SGROUNDEDPLUGWITHAN
EXTENSIONCORDORINANOUTLETUNLESSALLTHREE
PRONGSCANBEFULLYINSERTED.
DONOTOPENTHECABINET.THEREAREHIGH-VOLTAGE
COMPONENTSINSIDE.ALLSERVICINGMUSTBEDONEBY
QUALIFIEDDigitalProjectionSERVICEPERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
3. GSGV Acoustic Noise Information Ordinance:
The sound pressure level is less than 70 dB (A) according to
ISO 3744 or ISO 7779.
In UK, a BS approved power cable with moulded plug has a
Black (five Amps) fuse installed for use with this equipment. If
a power cable is not supplied with this equipment please
contact your supplier.
• IBM is a registered trademark of International Business Machines
Corporation.
• Macintosh and PowerBook are registered trademarks of Apple
Computer, Inc.
• Other product and company names mentioned in this user's manual
may be the trademarks of their respective holders.
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified
by Digital Projection in this manual. Failure to comply with this
government regulation could void your right to operate this
equipment.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
Important Safeguards
These safety instructions are to ensure the long life of your
projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away
from dust and moisture. Do not tilt the projector more than
±12° from side to side, as this will reduce lamp life. The
projector may be tilted forwards or backwards as necessary.
3. Do not place your projector in direct sunlight, near heaters or
heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm
internal components.
5. Handle your projector carefully. Do not hold the lens hood
and the terminal covers. Dropping or jarring can damage
internal components.
6. Do not place heavy objects on top of the projector.
±12° 360°

Digital Projection MERCURY 5000gv Important Information
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians
in order to ensure proper operation and reduce the risk
of bodily injury.
c. In addition, the ceiling must be strong enough to support
the projector and the installation must be in accordance
with any local building codes.
d. Please consult your dealer for more information.
To Dealer or Installer:
To prevent the projector from falling, install it in a place and
fasten it in a way with sufficient strength to support the
combined weight of the projector (25 kg / 55.1 lbs), the lens
and any mounting hardware, for an extended period of time as
well as to withstand earthquakes.
Power Supply
1. The projector is designed to operate on a power supply of
100-240 V 50/60 Hz AC. Ensure that your power supply fits
this requirement before attempting to use your projector.
2. Handle the power cable carefully and avoid excessive
bending. A damaged cord can cause electric shock or fire.
3. If the projector is not to be used for an extended period of
time, disconnect the plug from the power outlet.
4. Do not touch the power plug with wet hand. Doing so can
cause electrical shock or fire.
5. Do not touch the power plug during a thunder storm. Doing
so can cause electrical shock or fire.
Cleaning
1.Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily
soiled, use a mild detergent. Never use strong detergents or
solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful
not to scratch or mar the lens.
CAUTION
Do not unplug the power cable from the wall outlet under any
one of the following circumstances. Doing so can cause
damage to the projector:
• While the message "Please wait a moment." appears. This
message will be displayed after the projector is turned off.
• Immediately after the power cable is plugged into the wall
outlet (the POWER indicator has not changed to a steady
orange glow).
• Immediately after the cooling fan stops working (The cooling
fan continues to work for 90 seconds after the projector is
turned off).
CAUTION
• Do not try to touch the ventilation outlets as they can
become heated while the projector is turned on.
• Do not put the projector on its side when the lamp is turned
on.
Doing so may cause damage to the projector.
• Before shipping this projector, remove the lens and attach
the lens hood cap.
The Lens Shift mechanism may encounter damage caused
by improper handling during transportation.
• Do not eject a PC card or LAN card while its data is being
accessed. Doing so can damage your PC card or LAN card.
Lamp Replacement
• To replace the lamp, follow all instructions provided on page
9-2.
• Be sure to replace the lamp when the message "The Lamp
has reached the end of its usable life. Please replace the
lamp." appears. If you continue to use the lamp after the
lamp has reached the end of its usable life, the lamp bulb
may shatter, and pieces of glass may be scattered in the
lamp case. Do not touch them as the pieces of glass may
cause injury. If this happens, contact your Digital Projection
dealer for lamp replacement.
• Allow a minimum of 90 seconds to elapse after turning off
the projector. Then turn off the main power and disconnect
the power cable and allow 15 minutes to cool the projector
before replacing the lamp.
• The projector must be operated with two lamps installed
regardless of whether or not the lamp is active. Failure to do
so may degrade the performance of the projector such as
screen flicker or loss of lamp life. If one lamp has reached the
end of its usable life, replace it with a new one as soon as
possible.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are
unobstructed to prevent the build-up of heat inside your
projector. Allow at least 3 inches (10 cm) of space between
your projector and a wall, except to the rear and the
ventilation outlet on the right side, where there should be at
least 12 inches (30cm) of space.
2. Prevent foreign objects such as paper clips and bits of paper
from falling into your projector. Do not attempt to retrieve any
objects that might fall into your projector. Do not insert any
metal objects such as a wire or screwdriver into your projector.
If something should fall into your projector, disconnect it
immediately and have the object removed by a qualified
Digital Projection service personnel.
3. Do not place any liquids on top of your projector.
4. When using a LAN cable:
For safety, do not connect to the connector for peripheral
device wiring that might have excessive Voltage.
CAUTION
• Do not look into the lens while the projector is on. Serious
damage to your eyes could result.
• Keep any items such as magnifying glass out of the light
path of the projector. The light being projected from the lens
is extensive, therefore any kind of abnormal objects that can
redirect light coming out of the lens, can cause
unpredictable outcome such as fire or injury to the eyes.
• Do not cover the lens with the supplied lens hood cap or
equivalent while the projector is on. Doing so can lead to
melting of the cap and possibly burning your hands due to
the heat emitted from the light output.
v

Digital Projection MERCURY 5000gv
vi

Table of Contents Digital Projection MERCURY 5000gv
1. Introduction 7. Double Stacking and Link Mode
2
3
1
2
3
4
What's in the Box? .................................................................. 1-2
Introduction to the Projector ................................................ 1-3
Getting to Know Your Projector ............................................ 1-4
Control Panel Features ............................................................... 1-6
TerminalPanel Features ............................................................. 1-7
Remote Control Features ....................................................... 1-9
1
1
2
Stacking and Connecting the Projectors ............................. 7-2
Adjusting and Registering Signals to Be Projected........... 7-5
Adjusting the Lens Shift, Zoom and Focus to Clearly Display
all projected patterns ............................................................. 7-5
Link Mode Setting ................................................................... 7-5
List of Menu Items Available in Link Mode .......................... 7-6
Remote Control Precautions .....................................................1-11
Remote Control Battery Installation ..........................................1-11
Operating Range for Wireless Remote Control ........................1-11
Using the Remote Control in Wired Operation ......................... 1-12
2. Installation
1
Setting Up Your Projector ...................................................... 2-2
Screen Size and Projection Distance.......................................... 2-2
2
Lens Shift Adjustable Range ................................................. 2-4
Optional Lens Installation ..................................................... 2-5
Making Connections ............................................................... 2-6
3
4
Connecting Your PC or Macintosh ............................................. 2-6
To connect Scart Output ............................................................. 2-7
Connecting an External Monitor .................................................. 2-7
Connecting Your DVD Player ..................................................... 2-8
Connecting Your VCR or Laser Disc Player .............................. 2-9
Connecting to a Network .......................................................... 2-10
Connecting the Supplied Power Cable .......................................2-11
3. Projecting an Image (Basic Operation)
1
2
3
4
5
6
7
Turning on the Projector........................................................ 3-2
Selecting a Source .................................................................. 3-3
Adjusting the Picture Size and Position .............................. 3-3
Correcting the Horizontal and Vertical Keystone Distortion
(3D Reform) ............................................................................. 3-4
Optimizing RGB Picture Automatically................................. 3-6
Turning Up or Down Volume ................................................. 3-6
Turning off the Projector........................................................ 3-7
4. Convenient Features
1
2
3
4
5
6
7
Turning Off the Image and Sound......................................... 4-2
Enlarging and Moving a Picture ........................................... 4-2
Getting the On-line Help and Information ........................... 4-2
Using a USB Mouse ................................................................ 4-3
Using a USB HUB Function .................................................. 4-3
Changing Background Logo ................................................ 4-4
Making Freehand Drawings on Projected Image
(ChalkBoard) ........................................................................... 4-4
5. Using the Viewer
1
2
Making the Most out of the Viewer Function ....................... 5-2
Operating the Viewer Function from the Projector
(playback)................................................................................. 5-3
8. Using the On-Screen Menus
1
2
Basic Menu Operation ............................................................ 8-2
List of Direct Button Combinations ..................................... 8-3
Menu tree .................................................................................. 8-4
Menu Descriptions & Functions ............................................ 8-7
3
4
Source Select ............................................................................. 8-7
Adjust Source ............................................................................. 8-7
Picture ................................................................................. 8-8
Video Adjust ........................................................................ 8-8
Picture Management ............................................................ 8-9
Image Options ................................................................... 8-10
Option Adjust ..................................................................... 8-10
Signal Type.........................................................................8-11
Sound .........................................................................................8-11
Ref. Adjust ............................................................................... 8-12
Using 3D Reform .............................................................. 8-12
Screen Type ...................................................................... 8-12
Reference White Balance ................................................. 8-12
Reference Color Correction .............................................. 8-12
Factory Default ........................................................................ 8-13
Projector Options ...................................................................... 8-13
Menu .................................................................................. 8-13
Setup ................................................................................. 8-15
Lamp Settings ................................................................... 8-18
LinkMode .......................................................................... 8-18
LANMode .......................................................................... 8-19
Password ........................................................................... 8-23
Security ............................................................................. 8-24
Tools .......................................................................................... 8-25
Timer.................................................................................. 8-25
Capture .............................................................................. 8-27
PC Card Files .................................................................... 8-27
ChalkBoard ........................................................................ 8-27
Help .......................................................................................... 8-27
Contents ............................................................................ 8-27
Source Information ............................................................ 8-27
Projector Information......................................................... 8-28
Test Pattern .............................................................................. 8-28
9. Routine Maintenance
1
2
3
Replacing the Lamp ................................................................ 9-2
Replacing or Cleaning the Filter .......................................... 9-3
Cleaning the Cabinet and the Lens ...................................... 9-3
6. Using the Projector in a Network
1
2
3
4
5
6
Introduction ............................................................................. 6-2
Supported Equipment ............................................................ 6-3
Equipment Connections and Settings ................................. 6-4
Software Installation ............................................................... 6-5
Starting/Exiting the Software................................................. 6-6
Troubleshooting ..................................................................... 6-7
10. Appendix
USB Memory Device or
USB Memory Card Reader Support
......................................
10-2
Troubleshooting ................................................................... 10-3
Specifications ........................................................................ 10-5
Cabinet Dimensions ............................................................. 10-7
Pin Assignments of D-Sub RGB Input Connector ............ 10-7
Compatible Input Signal List .............................................. 10-8
REMOTE 1 Connector ........................................................... 10-9
PC Control Codes and Cable Connection ...................... 10-10
6
7
8
9
01
Cable Connection ................................................................... 10-10
PC Control Connector (D-SUB 9P) ........................................ 10-10
Using Software Keyboard .................................................. 10-10
Operation Using an HTTP Browser ................................... 10-11
vii

Digital Projection MERCURY 5000gv
viii

1
Introduction
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1
What's in the Box? ....................................1-2
Introduction to the Projector....................1-3
Getting to Know Your Projector ...............1-4
2
3
Control Panel Features...................................................................................... 1-6
Terminal Panel Features.................................................................................... 1-7
4
Remote Control Features..........................1-9
Remote Control Precautions .......................................................................... 1-11
Remote Control Battery Installation............................................................... 1-11
Operating Range for Wireless Remote Control ............................................ 1-11
Using the Remote Control in Wired Operation ............................................. 1-12

1-2
1. Introduction Digital Projection MERCURY 5000gv
1
What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your Projector.
NOTE: Lenses are optional. Order lenses from your Digital Projection dealer.
User Documentation
(102-537)
Projector
(001-560)
ON
OFF
ENTER
CANCEL
UNDO
AUTO
HELP
ON
TEST
ABC
1
DEF
2
GHI
3
JKL
4
MNO
5
PQR
6
STU
7
VWX
8
0
YZ
/
9
POWER INPUT
OFF
INFO
PIXEL SOUND OSD
MAGNIFY/
CTL
FOCUS
+
-
ZOOM
+
MENU/
ADDRESS
IMAGE/
PROJECTOR
POSI/
LENS
KEY ST
./
R
E-LIST/
PICTURE
ADJUST
WHITE BAL.
B
AMP/
G
PICT/
SHUT
-
MUTE
Remote control (102-161) and
batteries (AAx2)
Remote cable
(102-162)
Power cable for Europe (AC 230V)
(102-163)
Power cable for North America (AC 120V)
(102-165)
User Supportware
(102-191)
Power cable for United Kingdom (AC 230V)
(102-180)
Power cable for Japan (AC 100V)
(102-164)
DVI cable
(102-166)
16Mb PC card
(102-112)

2
MERCURY 5000gvDigital Projection
Introduction to the Projector
This chapter introduces you to the MERCURY 5000gv high end
fixed installation projector and describes key features and
controls.
Congratulations on Your Purchase of the MERCURY
5000gv projector
The MERCURY 5000gv is a compact three chip, XGA DLP™
projector, utilising the unique Dark Metal DMD™ technology
from Texas Instruments. With the MERCURY 5000gv you will
be able to project images up to 500" (measured diagonally)
from your DVD player, VCR, satellite hookup, HDTV source,
PC, Workstation or Macintosh computer (desktop or notebook)
and images from you digital camera PC Card or compact flash
memory. The MERCURY 5000gv incorporates integrated
networking access through the RJ45 input or provides for
wireless network connectivity from an optional wireless network
PC card. With extensive input and output panels, full suite of
quick-change lenses and a full function remote, the MERCURY
5000gv will let you immerse yourself in large screen viewing.
Features you’ll enjoy on the MERCURY 5000gv:
• Integrated RJ45 connector for wired networking ability
• Two optional modular card slots allow for future projector
growth with the ability to add additional input cards
• Dual PC card slots provide for optional wireless/wired
network connectivity or PC Card usage
• Email projector error status information to selected
individuals
• Power Horizontal and Vertical lens shift for optical display
corrections
• Digital Projection DigiView for enhanced video image
display, more vibrant colors and blacks richer with detail
• DigiScale enhanced image technology for increased
projector versatility that provides for horizontal, vertical and
diagonal keystone correction (allows for positioning the
projector in off center locations in the room and still get
aligned images)
• Display 16:9 or 4:3 information and fill the screen
• HDTV (1080p, 1080i, 720p) and SDTV (576p, 576i, 480p,
480i) compatibility
• a native resolution of XGA (1024x768).
• Intelligent lamp technology offers up to six user lamp
settings to maximize light output or lamp life and provide for
built in redundancy
• Smart security settings for password protection, control
panel lock, menu lock and PC card protection key to help
prevent unauthorized access and adjustments to the
projector
• ADA508 and Executive Order 13221 Federal Government
compliance *1
• DigiView 10-bit video decoder for expanded black levels and
adaptive gamma correction
• Digital photo viewer to display larger than life images from
your digital cameras PC card or compact flash card
• Double stackable for built in redundancy and high light
output requirements
1. Introduction
• Two timer settings - On/Off with programming or Sleep timer
that counts down at selected intervals
• 12V low voltage Screen Trigger output
• Easy set up and operation
• Eco-mode™ lamp technology for increased lamp life and
energy savings
• DigiView for uncompromising display of video and data.
Improves white level, color accuracy, dynamic range, and
display of varying levels of black in an image
• Wireless remote control operation
• External control via RS232, USB or Network
• DigiScale intelligent pixel blending technology provides for
extremely accurate image compression and HDTV
(1920x1080) display resolution*2.
• Supports most IBM VGA, SVGA, XGA, Macintosh,
component signal (YCbCr/YPbPr) or other RGB signals
within a horizontal frequency range of 15 to 100 kHz and a
vertical frequency range of 48 to 120 Hz. This includes
NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60 and SECAM
standard video signals
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
NTSC4.43: TV standard used in Middle East countries.
PAL: TV standard used in Western Europe.
PAL-M: TV standard used in Brazil.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
*1 This projector meetsADA508 compliance, the latest
American government regulation which provides for closed
captioning, including a menu system that can be viewed by
colorblind users. This model also meets Executive Order
13221 requirement for standby operation, which consumes
less than 1 watt.
*2 HDTV 1080p (1920x1080), HDTV 1080i (1920x1080),
HDTV 720 p (1280x720) and 1600x1200 are displayed with
DigiScale.
1-3

1-4
1. Introduction Digital Projection MERCURY 5000gv
Mounting holes for
stacking adaptors
Rear cover
Remote control
sensor
Remote control
sensor
Ventilation inlet
3
Getting to Know Your Projector
Controls
Terminal panel
(Left)
AC INPUT
Connect the supplied power
cable’s three-pin plug here.
Lens (optional)
Terminal panel (Right)
Remote control
sensor
Remote control
sensor
Ventilation outlet

1-5
Digital Projection MERCURY 5000gv 1. Introduction
Feet
(rotate to fine-adjust the height
and level of the projector)
Ventilation outlet
Remote control
sensors
2 x 5/8 UNC mounting holes
(maximum depth 1¼”)
4 x M8 mounting holes
(maximum depth 16mm)

1. Introduction Digital Projection MERCURY 5000gv
Control Panel Features 98
7
6
10 11
12
13
14
54
1. POWER Button (ON / STAND BY)( )
Use this button to turn the power on and off when the main
power is supplied and the projector is in standby mode or
idle mode.
NOTE: To turn on or off the projector, press and hold this button for a
minimum of two seconds.
2. POWER Indicator
When this indicator is green, the projector is on; when this
indicator is orange, it is in standby or idle mode. See the
Power Indicator section on page 10-3 for more details.
3. STATUS Indicator
If this light blinks red rapidly, it indicates that an error has
occurred, the lamp cover is not attached properly or the
projector has overheated. If this light remains orange, it
indicates that you have pressed a cabinet key while the
Control Panel Key Lock is enabled. See the Status Indicator
section on page 10-3 for more details.
4. LAMP Indicator 1/2
If this light blinks red rapidly, it's warning you that the lamp
has reached the end of its usable life. After this light
appears, replace the lamp as soon as possible (See page
9-2). See the Lamp Indicator section on page 10-3 for more
details.
5. PC CARD Access Indicator 1/2
Lights while accessing a PC card.
6. 3D REFORM Button
Press this button to enter 3D Reform mode to correct the
keystone (trapezoidal) distortion, and make the image
square. Press to toggle between Cornerstone and Keystone
adjustment mode.
NOTE: Pressing and holding this button for a minimum of 2 seconds
will reset 3D Reform correction setting values to zero.
32 1
7. AUTO ADJUST Button
Use this button to adjust Position-H/V and Pixel Clock/Phase
for an optimal picture. See page 3-6.
8. MENU Button
Displays the menu.
9. SELECT (+) (–) / Volume Buttons
: Use these buttons to select the menu of the item you
wish to adjust. When no menus appear, these buttons
work as a volume control.
: Use these buttons to change the level of a selected
menu item. A press of the button executes the
selection. When the menus or the Viewer tool bar is
not displayed, these buttons can be used to select a
slide, or to move the cursor in Folder List or Slide List.
10. ENTER Button
Executes your menu selection and activates items selected
from the menu.
11. CANCEL Button
Press this button to exit "Menus". Press this button to return
the adjustments to the last condition while you are in the
adjustment or setting menu.
12. LENS SHIFT Button
Adjust the lens offset by shifting the projected image position
horizontally and / or vertically.
13. ZOOM Button (+/-)
Zoom the lens in and out.
14. FOCUS Button (+/-)
Adjust the lens focus.
1-6

Digital Projection MERCURY 5000gv 1. Introduction
Terminal Panel (left) Features 3
21
8
7
4
56
1. RGB 1 Connectors [R/Cr, G/Y, B/Cb, H/V, V] (BNC)
Connect R,G,B,H (Horizontal sync) and V (Vertical sync)
outputs of external equipment.
If using a component with a combined sync (SYNC) output,
connect it to the H/V terminal. When using luminance and
color-difference signals of HDTV and DVD, connect Pr/Cr to
the R, Y to the G and Pb/Cb to the B input of the projector.
RGB 1 Audio Input Jacks (RCA)
L/MONO: This is your left channel audio input for stereo
sound coming from the RGB Input 1 source.
This also serves as your monaural audio input.
R: This is your right channel audio input for stereo sound
from the RGB Input 1 source.
2. RGB 2 Connector (Mini D-sub 15 Pin)
Connect your computer or other analog RGB equipment
such as IBM compatible or Macintosh computers. This also
serves as a component input connector that allows you to
connect a component video output of component equipment
such as a DVD player. This connector also supports SCART
output signal. See page 2-9 for more details.
RGB 2 Audio Iput Mini Jack (Stereo Mini)
This is where you connect audio output from your computer
or DVD player connected to the RGB2 input. A commercially
available audio cable is required.
3. DVI IN Connector (DVI-D 24 Pin)
This connector can be used to accept digital signal output
from a computer with a DVI connector.
DVI AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your
computer when connected to the DVI input. A commercially
available audio cable is required.
4. RGB OUT Connector (Mini D-Sub 15 Pin)
You can use this connector to loop your computer image to
an external monitor from the RGB 1 or 2 input source.
5. VIDEO IN Connector (BNC)
Connect a VCR, DVD player, laser disc player, or document
camera here to project video.
VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo
sound from a Video source.
6. S-VIDEO IN Connector (Mini DIN 4 Pin)
Here is where you connect the S-Video input from an
external source like a VCR.
NOTE: S-Video provides more vivid color and higher resolution than
the traditional composite video format.
S-VIDEOAUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo
sound from an S-Video source.
7. AUDIO OUT Jacks R/L (RCA)
You can use this connector to output sound from the
currently selected input source (RGB 1, RGB 2, DVI
(DIGITAL), Video or S-Video).
Output sound level can be adjusted in accordance with the
sound level of the internal speaker.
8. Slot 1/2
For optional RGB or SDI board.
1-7

1. Introduction Digital Projection MERCURY 5000gv
Terminal Panel (right) Features
12
6
5
10
3
4
7
8
9
1. USB Port [MOUSE/HUB] (Type A)
Connect a USB mouse. You can operate the menu or Viewer
with a USB mouse via this port.
• A USB-supported scanner or PC peripheral can be
connected to this port. (USB Hub Function. See page 4-3)
2. USB Port [PC] (Type B)
Connect this port to the USB port (type A) of your PC using a
USB cable. This port also serves as a PC Control port by
using Dynamic Image Utility 2.0 included on the supplied
CD-ROM.
3. PC CARD Slot 1/2
Insert a PC card, commercially available flash memory card
or Digital Projection optional wireless LAN card here.
There are two slots: Slot 1 and Slot 2.
4. PC CARD Eject Button 1/2
Press to eject a PC card partially. Each slot has its own eject
button: 1 and 2.
5. PC CONTROL Connectors (Mini D-Sub 9 pin)
For system expansion such as PC-Control using Dynamic
Image Utility included on the supplied User Supportware CD-
ROM or RS232C control from an external control system.
IN: connect to the external equipment such as a PC or
control system.
OUT: for daisy-chaining multiple projectors and operating
them with the same external equipment. To do so, connect to
a second projector’ s IN terminal to relay the input at the IN
terminal of the first projector until all the projectors are
connected.
6. SC. TRIGGER Mini Jack
When the projector is powered ON the screen trigger output
sends a low voltage trigger to the screen controller and the
screen will go down. When the projector is powered OFF the
screen trigger stops sending a low voltage trigger to the
screen controller and the screen will go up.
NOTE: To use this feature, you must turn on the Screen Trigger
function. See page 8-17.
Stereo mini cable Tip (12V)
(not supplied)
Ring (0V)
Sleeve (ground. 0V)
NOTE: Screen controllers are supplied and supported by screen
manufacturers.
NOTE: Do not use this jack for anything other than intended use.
Connecting wired remote control to the SC. TRIGGER Mini Jack
causes damage to the remote control.
7. LAN Port (RJ-45)
This port is typically used for UTP Ethernet/Fast Ethernet.
Use this connector to control the projector on a LAN. See
page 2-12.
8. REMOTE 1 (Mini D-Sub 15 Pin)
This terminal allows external control of the projector by use
of contact closure. See page 10-9.
9. REMOTE 2 Mini Jacks (IN/OUT)
IN: wired remote control input.
OUT: for daisy-chaining multiple projectors and operating
them with the same remote control. To do so, connect to a
second projector’ s IN terminal to relay the input at the IN
terminal of the first projector until all the projectors are
connected.
10. AC IN
When you plug the supplied power cable into an active wall
outlet and turn on the Main Power switch, the POWER
indicator turns orange and the projector is in standby mode.
See page 3-2.
Three types of power cable are supplied with this projector:
a three-pin type for the United Kingdom
b three-pin type for U. S. A. and Canada.
c Two-pin type for Europe and Japan.
1-8

4
Remote Control Features
MERCURY 5000gv
ON
1 2 3
4 5 6
7 8
0
9
+
-
ZOOM +
ON
R B
/
G
-
Digital Projection
ENTER
CANCEL
UNDO
AUTO
HELP
TEST
ABC DEF GHI
JKL MNO PQR
STU VWX YZ/
POWER INPUT
OFF
INFO
PIXEL SOUND OSD
MAGNIFY/
CTL
FOCUS
MENU/
ADDRESS
IMAGE/
PROJECTOR
POSI/ LENS
KEY ST./
OFF
E-LIST/
PICTURE
ADJUST
WHITE BAL.
AMP
PICT/ SHUT
MUTE
27
2
1
13
9
28
8
7
23
6
14
22
21 12
15 19
17 18
16 20
3
5
10
4
11
25
26
24
1. Introduction
1. POWER ON
Press and hold this button for a minimum of two seconds to
turn on the projector when the main power is supplied and
the projector is in standby mode or idle mode.
2. POWER OFF
Press and hold this button for a minimum of two seconds to
turn off the projector.
3. MENU
Press to display the main menu.
While pressing and holding CTL, press this button to display
the Remote Control ID dialog box to specify the remote
control ID. See page 7-2.
4. ENTER
Executes the menu selection and activates items selected
from the menu. When the slider or dialog box is displayed:
Pressing this button confirms adjustments/setting and
returns to the previous menu display.
5. Select (Up/Down/Left/Right)
: Use these buttons to select the menu of the item you
wish to adjust.
When no menus appear, these buttons work as a
volume control.
: Use these buttons to change the level of a selected
menu item.
A press of the button executes the selection.
Pressing and holding CTL, then pressing button works as
a Back Space key in the entry screen.
Pressing and holding CTL, then pressing this button moves
the menu, slider, toolbar or dialog box.
6.ADJUST WHITE BAL.
Press to display the Picture Management screen.
7.ADJUST PICTURE
Press to display the Picture adjustment screen. Pressing this
button sequentially selects adjustment screens.
8. IMAGE/PROJECTOR
Press to display the Image Option screen. Pressing this
button sequentially selects Image Options screens.
While pressing and holding CTL, pressing this button rotates
Projector Options screens.
9. Source / Input
Press to select input or to name a signal.
1 Selects RGB 1 input.
2 Selects RGB 2 input.
3 Selects DVI (DIGITAL) input.
4 Selects VIDEO input.
5 Selects S-VIDEO input.
6 Selects Viewer input
7 Selects LAN input
8 Selects OPTION SLOT 1* (optional RGB or SDI board)
9 Selects OPTION SLOT 2* (optional RGB or SDI board)
0 Sequentially selects: RGB1 (VIDEO)
→ RGB1 (S-VIDEO) →
* This button toggles between input 1 and 2.
NOTE: While pressing and holding CTL, pressing this button
switches to the selected signal found in the Entry List.
1-9

1. Introduction Digital Projection MERCURY 5000gv
10. UNDO
Press to return the adjustments and settings to the previous
condition. While pressing and holding CTL, pressing this
button clears the entire menus or adjustment/setting screen.
At this time the adjustments/settings are stored in memory
except the items on the setting screen with "OK" and
"Cancel" buttons such as the Menu and the Setup screen.
11. CANCEL
Press to exit the menu.
Press this button with CTL to return to the previous menu
without closing adjustment/setting screen while the menus
appear. This feature allows you to adjust or set several items
concurrently.
12. INFO
Displays the "Source Information" or "Projector Information"
window. This button toggles between these two windows.
While pressing and holding CTL, pressing this button stores
lens position settings.
13. TEST
Press to display the test pattern. Pressing this button
sequentially selects test patterns.
14. HELP
Provides online help.
15. PIXEL
Displays the Position/Clock screen to adjust the clock and
phase.
16.AUTO (RGB only)
Press to adjust Position-H/V and Pixel Clock for an optimal
picture.
17. POSITION
Press to display the Position screen; press again to display
the Blanking screen.
While pressing and holding CTL, pressing this button
displays the Lens Shift adjustment screen.
18. MUTE SOUND
Turns off the sound for a short period of time. Press again to
restore the sound.
19. MUTE OSD
Press to turn off the on-screen display. Press again to
restore the on-screen display.
NOTE: You can also turn off the on-screen display forcibly by
pressing and holding CTL and then pressing MUTE OSD (Forced
On-Screen Mute Mode) ; doing this again restores it. In this case any
adjustment will still change the projector's memory settings. This
mode is available even when input is switched to another or the
power is turned off the main power.
20. MUTE PICTURE
Press to turn off the picture for a short period of time. Press
again to restore the picture.
21. KEYSTONE (R)
Press to display the Keystone Correction (3D Reform)
screen.
This button toggles between “Cornerstone” and “Keystone”.
When the test pattern is displayed, while pressing and
holding CTL, pressing this button displays a red test pattern.
NOTE: Pressing and holding this button for a minimum of two
seconds will reset 3D Reform correction setting values to zero.
22.AMPLITUDE (G)
Service personnel only.
When the test pattern is displayed, while pressing and
holding CTL, pressing this button displays a green test
pattern.
23. ENTRY LIST (B)
Press to display the Entry List screen.
Pressing and holding CTL and then ENTRY LIST buttons
simultaneously, enters a signal in the Entry List when you
are not displaying a test pattern.
When the test pattern is displayed, while pressing and
holding CTL, pressing this button displays a blue test
pattern.
24. FOCUS (+/–)
While pressing and holding CTL, pressing this button allows
you to adjust the lens focus.
25. MAGNIFY/ZOOM (+/–)
Magnify the size of a target portion.
While pressing and holding CTL, pressing this button allows
you to zoom the lens in and out.
26. CTL
Used in conjunction with other buttons, similar to a shift key
on a computer.
ON
OFF
A
UTO
HELP
ON
TEST
ABC
1
DEF
2
GHI
3
JKL
4
MNO
5
PQR
6
STU
7
VWX
8
0
YZ/
9
POWER INPUT
OFF
INF
O
PIXEL SOUN
D
NU
/
ADD
RE
IMAGE/
PROJECTOR
POSI/
LENS
KEYST./
R
E-LIST/
PICTURE
ADJUST
WHITEBAL.
B
AMP
/
G
PICT/
SHUT
28
29 27
27. Remote Jack
Connect your remote cable here for wired operation.
28. Backlight Switch
When using the remote control wirelessly:
Turns the backlight on and off. If no button is pressed within
30 seconds, the backlight will turn off to conserve battery life.
29. Infrared Transmitter
Direct the remote control toward the remote sensor on the
projector cabinet.
1-10

1-11
Digital Projection MERCURY 5000gv 1. Introduction
Remote Control Precautions
• The remote control system may not function when direct sunlight or
strong illumination strikes the remote control sensor of the main unit,
or when there is an obstacle in the path.
• When remote control buttons are pressed and held, projector’s
function keys may not operate.
• Do not subject to strong shock.
• Do not allow water or other liquid to splash on the remote control. If
the remote control gets wet, wipe it dry immediately.
• Avoid exposure to heat and steam.
• Remove the batteries from the remote control when the remote
control is not going to be used for a long period.
Remote Control Battery Installation
Installing the Remote Control Batteries
When it comes time to replace the batteries, two "AA" type will
be required.
1. Press and open the cover.
2. Align and insert the batteries according to the (+) and (-) indications
inside the case.
3. Replace the cover.
Operating Range for Wireless Remote Control
The infrared signal operates by line-of-sight up to a distance of
approximately 7m (20 feet) and a 60 degree angle of the
remote sensor.
The projector will not function if there are objects between the
remote sensor and the remote control or if strong light falls on
the remote sensor. Weak batteries will also prevent the
projector from operating properly.
Remote sensors on
the projector cabinet
Side View
Remote
control
NOTE: Not to scale.
NOTE: You cannot operate the projector using the remote control if:
• The remote control ID is not set to [None].
• The remote ID is not the same as the projector ID.
See page 7-2 for setting remote ID and projector ID.
Remote
control

1-12
1. Introduction Digital Projection MERCURY 5000gv
Using the Remote Control in Wired Operation
Connect one end of the supplied remote cable to the REMOTE 2
IN mini jack and the other end to the remote jack on the remote
control.
NOTE: Do not use this jack for anything other than intended use.
Connecting the wired remote control to the SC. TRIGGER Mini Jack
causes damage to the remote control.
Remote cable (supplied)
REMOTE 2
IN