Digital Projection Titan 1080p-250 Operating manual

TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
105-924E
page 3 Super High Brightness Digital Video Projector
Important Information
seite 10 Super High Brightness Digitaler Videoprojektor
Wichtige Informationen
page 17 Vidéo projecteur numérique à forte luminosité
Informations importantes
página 24 Vídeo-proyector digital de alta luminosidad
Información importante
pagina 31 Proiettore video digitale ad alta luminosità
Informazioni importanti
sid. 38 Digital videoprojektor Super High Brightness
Viktig information

Digital Projection TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
Digital Projection
Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Office: as above
Tel [phone]
Fax [phone]
Email [email protected], [email protected]
Web Site www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel (USA) 770 420 1350
Fax (USA) 770 420 1360
Email [email protected]
Web Site www.digitalprojection.com

Digital Projection TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
Rev E March 2008 Page 3
This information booklet contains the following extracts from the User Manual:
Contents
Symbols used in the User Manual ....................................................................................2
Declaration of Conformity .................................................................................................3
General precautions...........................................................................................................4
Installation precautions .....................................................................................................5
Operation and configuration precautions........................................................................6
Compliance with international standards ........................................................................6
Noise ...............................................................................................................................................6
RF Interference...............................................................................................................................6
Specifications .....................................................................................................................7
Part numbers..................................................................................................................................7
Optical.............................................................................................................................................7
Electrical .........................................................................................................................................8
Physical...........................................................................................................................................8
Full information about operating, connecting and setting up the projector can be found in the
User Manual, located on the CD.
Symbols used in the User Manual
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock
unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself
and/or damage to the equipment unless the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
English

Digital Projection TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
Page 4 Rev E March 2008
Declaration of Conformity
Directives covered by this Declaration
2004/108/EC Electromagnetic Compatibility Directive.
2006/95/EC Low Voltage Equipment Directive.
Products covered by this Declaration
Large screen video projector type The CE mark was first applied in:
TITAN sx+-500 June 2006
TITAN HD 500 July 2006
TITAN HD 250 July 2006
TITAN XG 500 July 2006
TITAN 1080p 500 June 2007
TITAN 1080p 250 June 2007
Basis on which Conformity is being declared
The products identified above comply with the protection requirements of the above EU directives, and
the manufacturer has applied the following standards.
EN 55022:1998 - Limits and Methods of Measurement of Radio Disturbance Characteristics of
Information Technology Equipment.
EN 55024:1998 - Limits and Methods of Measurement of Immunity Characteristics of Information
Technology Equipment.
EN 55103:1997 - Product family Standard for Audio, Video, Audio-Visual and Entertainment
Lighting Control apparatus for Professional Use.
EN 60950-1:2001- Specification for Safety of Information Technology Equipment, including
Electrical Business equipment.
The technical documentation required to demonstrate that the products meet the requirements of the
Low Voltage directive has been compiled by the signatory below and is available for inspection by the
relevant enforcement authorities.
Signed:
Authority: D.J. Quinn, Product Development Director
Date: 25 June 2007
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations
to use which must be observed when these products are taken into service to maintain compliance
with the above directives. Details of these special measures are available on request, and are also
contained in the product manuals.
English

Digital Projection TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
Rev E March 2008 Page 5
General precautions
Do not open the cabinet. There are no user serviceable parts inside.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this equipment MUST be
earthed.
Take care to prevent small objects such as paper or wire from falling into the projector.
If this does happen, switch off immediately, and have the objects removed by
authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any liquids on top of
the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a damaged power
cable.
There are no user-serviceable parts inside the lamp module. The whole module should
be replaced.
Take care when removing the lamp module.
NEVER touch the lamp or reflector.
Take care not to touch the glass surface of the lamp module. If you do accidentally
touch the glass, it should be cleaned before use. (see section 5. Maintenance.)
Do not use the lamp for more than 1500 hours, as this may cause serious lamp failure,
damage the lamp module and cause extra cost on replacement.
HID lamps produce high intensity light. Do not look directly at the light coming from the
lamp housing, or the lens, or allow items such as magnifying lenses to be placed in the
light path. This could result in serious eye damage.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could cause a fire
Always allow the projector to cool for 5 minutes before disconnecting the power,
moving the projector or changing the lamp.
Never use strong detergents or solvents such as alcohol or thinners to clean the
projector and lens.
English

Digital Projection TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
Page 6 Rev E March 2008
Installation precautions
Connect the LAN cable only to a computer LAN connection. Other similar connectors
may have a dangerously high voltage source.
The projector must be installed only by suitably qualified personnel, in accordance with
local building codes.
The projector should be installed as close to the power outlet as possible.
The power connection should be easily accessible, so that it can be disconnected in an
emergency.
Ensure that there is at least 30cm (12in) of space between the ventilation outlets and
any wall, and 10cm (4in) on all other sides.
Do not install the projector close to anything that might be affected by its operational
heat, for instance, polystyrene ceiling tiles, curtains etc.
The projector weighs approximately 27 kg (50 lbs). Use safe handling techniques when
lifting the projector.
When stacking projectors, the stack MUST be vertical, to ensure that the stresses are
distributed to all frame couplings.
Before installation, make sure that the surface, ceiling or rigging that is to support the
projector is capable of supporting the combined weight of the projector and lens (see
specification for exact weights).
Separate backup safety chains or wires should always be used for each projector.
Do not place heavy objects on top of the projector chassis. Only the chassis corners
and the rigging frame are capable of withstanding the weight of another projector.
Do not stack more than 3 projectors.
Do not drop or jarr the projector.
1080p, sx+500: The lens release lever should always be set to the locked position to
prevent the lens from falling out.
Place the projector in a dry area away from sources of dust, moisture, steam, smoke,
sunlight or heat.
Do not tilt the projector more than ±12° from side to side when in use, as this may
cause serious lamp failure, damage the lamp
module and cause extra cost on replacement.
The projector my be tilted forwards and
backwards as necessary.
±12°
360°
English

Digital Projection TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
Rev E March 2008 Page 7
Operation and configuration precautions
Do not make changes to the networking configuration unless you understand what you
are doing, or have taken advice from your Network Manager. If you make a mistake, it is
possible that you will lose contact with the projector. Always double-check your
settings before pressing the APPLY button. Always keep a written note of the original
settings, and any changes you have made.
Software update should NOT be carried out except by, or with the supervision of, Digital
Projection Service personnel.
Compliance with international standards
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
RF Interference
FCC
The Federal Communications Commission does not allow any modifications or changes to the unit
EXCEPT those specified by Digital Projection in this manual. Failure to comply with this government
regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant with Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful interference, in which case the
user will be responsible for correcting any interference.
This equipment contains an FCC approved RF transmitter module with FCC ID: R68WIPORT.
European Waste Electrical and Electronic Equipment (WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and Electronic Equipment. Our
products are designed with reuse, recycling and recovery of all components in mind. To this
end, at end of life, your projector may be returned to Digital Projection Ltd or its agent so that
the environmental impact can be minimised.
English

Digital Projection TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
Page 8 Rev E March 2008
Specifications
Part numbers
Projector 1080p 500: 106-241, with SDI: 108-642,
1080p 250: 106-242, with SDI: 108-641, sx+ 500: 105-925,
HD 500: 105-948, HD-250: 106-240, XG 500: 106-239
Power cable 10A, Europe 102-163 United Kingdom 102-180
Power cable 13A, North America 102-165 Rigging frame 104-923
Remote control 105-023 4x AAA batteries 105-922
Remote cable 5m 102-162
User manual on CD 105-923 Important Information 105-924
Lamp module 001-742 Air filter 102-064
Lenses sx+ 500
0.73 : 1 fixed lens 105-607
1.2 : 1 fixed lens (3 - 15m) 105-608
1.2 : 1 fixed lens (1.2 - 2.0m) 105-609
1.5 - 2.02 : 1 zoom lens 105-610
2.02 - 2.77 : 1 zoom lens 105-611
2.77 - 4.51 : 1 zoom lens 105-612
4.51 - 7.53 : 1 zoom lens 105-613
Lenses 1080p 500/250 High Brightness High Contrast
0.67 : 1 fixed lens 105-607 107-195
1.12 : 1 fixed lens (3 - 15m) 105-608 105-608
1.12 : 1 zoom lens (1.2 - 2m) 105-609 105-609
1.39 - 1.87 : 1 zoom lens 105-610 107-196
1.87 - 2.56 : 1 zoom lens 105-611 107-197
2.56 - 4.16 : 1 zoom lens 105-612 107-198
4.16 - 6.96 : 1 zoom lens 105-613 107-199
Lenses HD 500/250 High Brightness High Contrast
0.63 : 1 fixed lens 001-734 102-373
0.96 : 1 fixed lens 001-735 102-835
1.2 - 1.44 : 1 zoom lens 001-736 102-374
1.44 - 1.8 : 1 zoom lens 001-737 102-375
1.8 - 2.4 : 1 zoom lens 001-738 102-376
2.4 - 3.6 : 1 zoom lens 001-739 102-377
3.6 - 5.6 : 1 zoom lens 001-740 102-378
Lenses XG 500
0.8 : 1 fixed lens 001-734
1.2 : 1 fixed lens 001-735
1.5 - 1.8 : 1 zoom lens 001-736
1.8 - 2.25 : 1 zoom lens 001-737
2.25 - 3.0 : 1 zoom lens 001-738
3.0 - 4.5 : 1 zoom lens 001-739
4.5 - 7.0 : 1 zoom lens 001-740
Optical
Digital Light Processor 1080p 500/250: 3 x 0.95” Texas Instruments DMD™,
resolution 1920 x 1080 pixels
sx+ 500: 3 x 0.94” Texas Instruments DMD™,
resolution 1400 x 1050 pixels
HD 500/250: 3 x 0.8” Texas Instruments DMD™,
resolution 1280 x 720 pixels
XG 500: 3 x 0.7” Texas Instruments DMD™,
resolution 1024 x 768 pixels
English

Digital Projection TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
Rev E March 2008 Page 9
Contrast Ratio 1080p 500: >2000:1 250: >5000:1 full field (±10%)
sx+ 500: >1600:1 full field (±10%)
HD 500: >1200:1 full field (±10%) (High Brightness lens)
HD 250: >4000:1 full field (±10%) (High Contrast lens)
XG 500: >1200:1 full field (±10%)
Pixel fill factor 1080p: 87%, sx+, HD, XG: 90%
Lamp power 500: 2 x 250W, 250: 1 x 250W
Lamp life (typical) 500: 1500 hours in dual lamp mode , 3000 in single lamp
mode
250: 1500 in single lamp mode
Brightness 1080p 500: 6000 ANSI lumens (±10%) in dual lamp mode
1080p 250: 2000 ANSI lumens (±10%)
sx+ 500: 5500 ANSI lumens (±10%) in dual lamp mode
HD 500: 4500 ANSI lumens dual lamp (High Brightness lens)
HD 250: 1600 ANSI lumens (±10%) (High Contrast lens)
XG 500: 4500 ANSI lumens (±10%) in dual lamp mode
Colour temperature Native: 7500°K (±1000°K),
White balance adjustment: 3000°K - 10000°K
Electrical
Inputs RGB1, RGB2, DVI, Composite Video, S-Video, Component.
sx+ 500 and 1080p only: and SDI
Pixel clock up to 165MHz
Control inputs 1 x LAN
1 x wifiLAN (FCC ID: R68WIPORT)
1 x RS232 serial: 19200 baud, 8 bits, 1 stop bit, no parity
1 x remote control
Mains voltage 100-230 VAC ±10%, 48-62Hz (single phase)
Power consumption 500: 750 W, 250: 500W
International Regulations Meets FCC Class A requirements
Meets EMC Directives (EN 55022, EN 55024, EN 55103)
Meets Low Voltage Directive (EN60950)
Indicators Input, Power, Shutter, Error, IR, Lamp 1, Lamp 2 (500 only)
Physical
Operating Temperature 0 to 40°C
Storage Temperature -10 to 50°C
Thermal Dissipation 500: 2600 BTU/hr, 250: 1733 BTU/hr
Operating Humidity 20% to 80% non-condensing
Weight approximately 27 kg (60 lbs)
FCC WIFI ID, R68WIPORT
English

Digital Projection TITAN 1080p-500/250, sx+-500, HD-500/250, XG-500
Page 10 Rev E March 2008
Dieses Informationsheft enthält die folgenden Auszüge aus dem Benutzerhandbuch:
Inhalt
Symbol in diesem Leitfaden..............................................................................................9
Konformitätserklärung.....................................................................................................10
Allgemeine Vorsichtsmaßnahmen ..................................................................................11
Vorsichtsmaßnahmen bei der Installation .....................................................................12
Vorsichtsmaßnahmen bei Betrieb und Konfiguration ..................................................13
Übereinstimmung mit internationalen Standards .........................................................13
Lärm ..............................................................................................................................................13
Funkstörung .................................................................................................................................13
Technische Daten .............................................................................................................14
Teilenummern...............................................................................................................................14
Optisch..........................................................................................................................................14
Elektrisch......................................................................................................................................15
Physisch .......................................................................................................................................15
Vollständige Informationen über den Betrieb, den Anschluss und die Einstellungen des
Projektors finden Sie im Benutzerhandbuch auf der CD.
Symbol in diesem Leitfaden
ELEKTRISCHE WARNUNG: Dieses Symbol weist darauf hin, dass Stromschlaggefahr
besteht, wenn die Anweisungen nicht strikt befolgt werden.
WARNUNG: Dieses Symbol weist darauf hin, dass die Gefahr von Körper- und
Sachschäden besteht, wenn die Anweisungen nicht strikt befolgt werden.
HINWEIS: Dieses Symbol weist auf wichtige Informationen hin, die Sie lesen sollten.
Deutsche