Digital Projection HIGHlite 660 3D Series User manual

Rev A December 2013
USER MANUAL
INSTALLATION AND QUICK-START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REMOTE COMMUNICATIONS GUIDE
REFERENCE GUIDE
114-242A
HIGHlite 660 3D Series
High Brightness Digital Video Projector

Digital Projection HIGHlite 660 3D Series NoTOC
i
Rev A December 2013
Digital Projection HIGHlite 660 3D Series
i
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Keep this manual handy for future reference.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2013 Digital Projection Ltd. All rights reserved.
Notes

Digital Projection HIGHlite 660 3D Series NoTOC
ii
Rev A December 2013
Digital Projection HIGHlite 660 3D Series
ii
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• Support for most 3D standards
• Full range of digital and legacy analog inputs
• Control of most aspects of the projector’s operation via LAN and RS232
• Support for a number of aspect ratios and screen sizes
• Nonlinear warp adjustment by moving points on an interpolated grid
• Ceiling mount and rear-screen installation options
• Simultaneous display of two sources via Picture-In-Picture
• Long lamp life
• Motorised lens mount
A serial number is located on the back of the projector. Record it here:
Notes

Digital Projection HIGHlite 660 3D Series NoTOC
iii
Rev A December 2013
Digital Projection HIGHlite 660 3D Series
iii
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
WHAT’S IN THE BOX? ................................................................... 3
CONNECTING THE POWER SUPPLY ............................................. 4
PROJECTOR OVERVIEW ............................................................... 5
Front and rear views ............................................................................. 5
Control panel indicators ........................................................................ 6
REMOTE CONTROL....................................................................... 7
Infrared reception.................................................................................. 9
POSITIONING THE SCREEN AND PROJECTOR........................... 10
CHANGING THE LENS................................................................. 11
Inserting a new lens ............................................................................ 11
Removing the lens .............................................................................. 12
OPERATING THE PROJECTOR.................................................... 13
Switching the projector on................................................................... 13
Switching the projector off................................................................... 13
Adjusting the lens................................................................................ 14
Zoom................................................................................................ 14
Focus ............................................................................................... 14
Shift ................................................................................................. 14
Selecting an input signal or test pattern.............................................. 15
Input signal ........................................................................................ 15
Test pattern ........................................................................................ 15
Adjusting the image............................................................................. 16
Orientation ......................................................................................... 16
Keystone ........................................................................................... 16
Picture .............................................................................................. 16
CONNECTION GUIDE ............................................................................17
SIGNAL INPUTS AND OUTPUTS.................................................. 19
Analog inputs ...................................................................................... 19
Digital inputs and outputs.................................................................... 20
Low latency inputs............................................................................... 21
DVI connection example ..................................................................... 22
EDID on the DVI and VGA inputs........................................................ 23
Using HDMI/DVI switchers with the projector ..................................... 23
3D connections ................................................................................... 24
3D sources up to 60Hz requiring frame doubling and left/right interleaving.......... 24
3D sources above 60Hz not requiring frame doubling.................................... 24
Dual Pipe 3D ...................................................................................... 24
3D Sync............................................................................................... 25
3D Sync in ......................................................................................... 25
3D Sync out ....................................................................................... 25
CONTROL CONNECTIONS........................................................... 26
LAN ..................................................................................................... 26
Wired remote control........................................................................... 26
Service port......................................................................................... 27
RS232 ................................................................................................. 27
Update port ......................................................................................... 27
LAN connection examples .................................................................. 28
RS232 connection example ................................................................ 29

Digital Projection HIGHlite 660 3D Series NoTOC
iv
Rev A December 2013
Digital Projection HIGHlite 660 3D Series
iv
OPERATING GUIDE ................................................................................31
USING THE MENUS ..................................................................... 33
Menus and sub-menus........................................................................ 33
Drop-down lists ................................................................................... 34
Sliders ................................................................................................. 35
Commands.......................................................................................... 35
Editing elds........................................................................................ 36
USING THE PROJECTOR............................................................. 37
Main menu .......................................................................................... 37
Lens menu .......................................................................................... 38
Zoom................................................................................................ 38
Focus ............................................................................................... 38
Center Lens ....................................................................................... 38
Nudge............................................................................................... 39
Lens Presets ...................................................................................... 39
Image menu ........................................................................................ 40
Video Filters ....................................................................................... 40
VGA Setup......................................................................................... 40
Color menu.......................................................................................... 41
Gamut .............................................................................................. 41
Black Level and Gain sliders................................................................... 41
Geometry menu .................................................................................. 42
Aspect Ratio....................................................................................... 42
Overscan........................................................................................... 42
Size & Position.................................................................................... 43
Geometry Engine................................................................................. 44
Edge Blend menu................................................................................ 50
Overview ........................................................................................... 50
Array H Position and V Position............................................................... 51
S-Curve Value .................................................................................... 52
Blending............................................................................................ 54
Segmentation ..................................................................................... 55
Blend Width........................................................................................ 58
Black Level Uplift ................................................................................. 58
Reduce Black Level Uplift Width .............................................................. 59
Blending images from multiple projectors ........................................... 60
Before you start................................................................................... 60
Edge Blend procedure .......................................................................... 61
PIP menu ............................................................................................ 69
3D menu.............................................................................................. 70
3D types............................................................................................ 71
Some 3D settings explained ............................................................... 73
Dark Time.......................................................................................... 73
Source Dominance............................................................................... 73
Sync Offset ........................................................................................ 73
Frame Rate Multiplier............................................................................ 74
Lamps menu ....................................................................................... 75
Setup menu......................................................................................... 76
Reset Default Settings .......................................................................... 76
Input Conguration............................................................................... 77
Network ............................................................................................ 78
On Screen Display ............................................................................... 79
System ............................................................................................. 80
Setting up an IR address ....................................................................... 81
CONTENTS (continued)

Digital Projection HIGHlite 660 3D Series NoTOC
v
Rev A December 2013
Digital Projection HIGHlite 660 3D Series
v
Information menu ................................................................................ 82
Lamps .............................................................................................. 82
Conguration...................................................................................... 82
REMOTE COMMUNICATIONS GUIDE ..........................................83
INTRODUCTION........................................................................... 85
Network setup ..................................................................................... 85
Serial Port setup.................................................................................. 85
Remote communications commands.................................................. 86
Examples .......................................................................................... 86
COMMAND GUIDE ....................................................................... 87
Input Selection menu .......................................................................... 87
Test Pattern menu ............................................................................... 87
Lens menu .......................................................................................... 87
Image menu ........................................................................................ 88
Color menu.......................................................................................... 89
Geometry menu .................................................................................. 90
Edge Blend menu................................................................................ 91
PIP menu ............................................................................................ 93
3D menu.............................................................................................. 94
Lamps menu ....................................................................................... 94
Setup menu......................................................................................... 95
Information menu ................................................................................ 96
Miscellaneous commands................................................................... 96
WEB CONFIGURATION UTILITY .................................................. 99
Menu examples................................................................................... 99
Using the Discovery Tool to view your network................................. 101
REFERENCE GUIDE..............................................................................103
THE DMD™................................................................................ 106
CHOOSING A LENS ................................................................... 108
Basic calculation ............................................................................... 109
Basic calculation example................................................................. 110
Full lens calculation............................................................................111
Introducing TRC .................................................................................111
Calculating TRC ................................................................................ 112
Calculating the throw ratio with TRC ....................................................... 113
Full lens calculation example ............................................................ 114
SCREEN REQUIREMENTS..........................................................115
Fitting the image to the DMD™......................................................... 115
1080p images displayed full width .......................................................... 115
1080p images displayed full height......................................................... 116
WUXGA images displayed full width ....................................................... 117
WUXGA images displayed with a height of 1080 pixels................................ 117
WUXGA images displayed full height ...................................................... 118
Diagonal screen sizes....................................................................... 119
Fitting the image to the screen.......................................................... 120
Positioning the screen and projector................................................. 121
POSITIONING THE IMAGE......................................................... 122
Maximum offset range....................................................................... 124
CONTENTS (continued)

Digital Projection HIGHlite 660 3D Series NoTOC
vi
Rev A December 2013
Digital Projection HIGHlite 660 3D Series
vi
ASPECT RATIOS EXPLAINED.................................................... 125
Aspect ratio examples for DMD™ resolution 1080p ......................... 126
Aspect ratio examples for DMD™ resolution WUXGA...................... 129
Aspect ratio example: TheaterScope................................................ 132
FRAME RATES AND PULLDOWNS EXPLAINED......................... 133
Interlaced and progressive scan ....................................................... 133
Frame rates of image sources .......................................................... 133
Pulldowns - conversion into destination formats............................... 134
2:3 (normal) pulldown ......................................................................... 134
2:3:3:2 (advanced) pulldown................................................................. 135
APPENDIX A: LENS PART NUMBERS........................................ 136
APPENDIX B: LENS CHARTS .................................................... 137
How to use the lens charts ................................................................... 137
1080p (1920 x 1080 pixels) .................................................................. 138
WUXGA (1920 x 1200 pixels)................................................................ 139
DMD™ resolution 1080p / WUXGA, full DMD™ width images ....................... 140
DMD™ resolution 1080p, 1.25:1 images.................................................. 141
DMD™ resolution 1080p, 1.33:1 images.................................................. 142
DMD™ resolution 1080p, 1.6:1 images ................................................... 143
DMD™ resolution 1080p, 1.66:1 images.................................................. 144
DMD™ resolution WUXGA, 1.25:1 images ............................................... 145
DMD™ resolution WUXGA, 1.33:1 images ............................................... 146
APPENDIX C: SUPPORTED SIGNAL INPUT MODES .................. 147
2D input modes................................................................................. 147
3D input modes................................................................................. 150
APPENDIX D: MENU MAP.......................................................... 152
CONTENTS (continued)
APPENDIX E: WIRING DETAILS................................................. 159
Signal inputs and outputs.................................................................. 159
VGA ............................................................................................... 159
HDMI 1 ........................................................................................... 160
Output: SPDIF .................................................................................. 160
DVI 1.............................................................................................. 161
3G-SDI ........................................................................................... 162
CVBS 1 (Composite 1) ........................................................................ 162
S-Video........................................................................................... 162
Component ...................................................................................... 162
CVBS 2 (Composite 2) ........................................................................ 162
DVI 2.............................................................................................. 163
HDMI 2 and 3 ................................................................................... 163
HDBaseT input.................................................................................. 163
Control connections .......................................................................... 164
Update port ...................................................................................... 164
Service port...................................................................................... 164
Wired remote control .......................................................................... 164
RS232 ............................................................................................ 165
LAN connection................................................................................. 165
APPENDIX F: GLOSSARY OF TERMS........................................ 166

Digital Projection HIGHlite 660 3D Series NoTOC
vii
Rev A December 2013
Digital Projection HIGHlite 660 3D Series
vii
TECHNICAL SPECIFICATIONS .................................................. 179
Models............................................................................................... 179
Inputs and outputs............................................................................. 180
Bandwidth ......................................................................................... 180
Remote control and keypad .............................................................. 180
Automation control ............................................................................ 180
Color temperature ............................................................................. 180
Lamps ............................................................................................... 181
Lenses............................................................................................... 181
Lens mount ....................................................................................... 181
Mechanical mounting ........................................................................ 181
Orientation......................................................................................... 181
Electrical and physical specications................................................ 182
Safety & EMC regulations................................................................. 182
Accessories....................................................................................... 182
CONTENTS (continued)

Rev A December 2013
INSTALLATION AND QUICK-START GUIDE
HIGHlite 660 3D Series
High Brightness Digital Video Projector

Digital Projection HIGHlite 660 3D Series IN THIS GUIDE Installation and Quick-Start Guide
Rev A December 2013
IN THIS GUIDE
What’s In The Box?............................................................................................. 3
Connecting The Power Supply........................................................................ 4
Projector Overview............................................................................................. 5
Front and rear views ...................................................................................................5
Control panel indicators.............................................................................................6
Remote Control.................................................................................................... 7
Infrared reception........................................................................................................9
Positioning The Screen And Projector....................................................... 10
Changing The Lens........................................................................................... 11
Inserting a new lens..................................................................................................11
Removing the lens ....................................................................................................12
Operating The Projector ................................................................................. 13
Switching the projector on.......................................................................................13
Switching the projector off.......................................................................................13
Adjusting the lens .....................................................................................................14
Zoom...............................................................................................................................14
Focus ..............................................................................................................................14
Shift.................................................................................................................................14
Selecting an input signal or test pattern.................................................................15
Input signal......................................................................................................................15
Test pattern .....................................................................................................................15
Adjusting the image..................................................................................................16
Orientation ......................................................................................................................16
Keystone .........................................................................................................................16
Picture.............................................................................................................................16

Digital Projection HIGHlite 660 3D Series WHAT’S IN THE BOX? Installation and Quick-Start Guide
3
Rev A December 2013
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
VGA HDMI DVI 3GSDI
CVBS1 SVIDEO
CLOSE
12 3 4
COMP CVBS2
5 6 7 8
9 0 10+ #
MAIN SUB DUAL HD-T
OFF ON
ALT ROLL
PITCH YAW
FOCUS CAL
SHIFT ZOOM
EYE
SWAP
MAIN/PIP
SWAP
BRI CON GAMMA 3D
ON/OFF
PIP
ON/OFF
LOAD SAVE TEST ADDR
BACKLIGHT
RGB
PRESET
SHUTTER
OPEN
POWER
MENU
OK
EXIT INFO
Remote control
(105-023)
4x AAA batteries
User Guides on CD
(114-241)
Important Information (114-243)
Power cable, Europe
(102-163)
Power cable, North America
(102-165)
Projector
Power cable, United Kingdom
(102-180)

Digital Projection HIGHlite 660 3D Series CONNECTING THE POWER SUPPLY Installation and Quick-Start Guide
4
Rev A December 2013
Connecting The Power Supply
Lift the cable lock up, push the mains connector in rmly and
push the lock down to secure the cable.
1AC mains inlet with cable lock
Rear view of the projector
1
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.

Digital Projection HIGHlite 660 3D Series PROJECTOR OVERVIEW Installation and Quick-Start Guide
5
Rev A December 2013
Projector Overview
Front and rear views
1Front infrared window
2Lens
3Air outlet
4Adjustable feet
5Control panel
6Rear infrared window
7Connection panel
8Power switch and power connection
9Air inlet
9
5
8
76
Rear view
Front view
4
12 3 Notes

Digital Projection HIGHlite 660 3D Series PROJECTOR OVERVIEW Installation and Quick-Start Guide
6
Rev A December 2013
Control panel indicators
1Power indicator
Behavior Meaning
Off The projector is switched off.
On (amber) The projector is in Standby mode.
On (green) The projector is switched on (Normal mode).
2Shutter indicator
Behavior Meaning
On (amber) The shutter is closed.
On (green) The shutter is open.
3Error indicator
Behavior Meaning
On (red) Voltage Error
Flashing Temperature Error
4Lamp 1 and Lamp 2 indicators
Behavior Meaning
On (green) The lamp is switched on (100%).
On (amber) The lamp is switched on (85-99%).
Flashing (green) The lamp is warming up.
Flashing (amber) The lamp is cooling down.
Flashing (red) Lamp Error
5Infrared indicator
Behavior Meaning
Flashing (blue) The projector is receiving input from the remote control.
Notes
During startup all LEDs light up
at the same time to indicate the
projector is carrying out a self-test.
3
1 2
4 5

Digital Projection HIGHlite 660 3D Series REMOTE CONTROL Installation and Quick-Start Guide
7
Rev A December 2013
Remote Control
1Transmit indicator
Flashes when the remote control sends a signal to the projector.
Lights solidly when the projector is in LENS ADJUSTMENT mode.
2Power ON / OFF
3ALT
Acts as a shift key. To use, press and hold this button, then press a green-labeled
button.
4Shutter OPEN / CLOSE
5MENU
Access the projector OSD (on-screen display).
6Navigation
Navigate through the menus with the arrows, conrm your choice with OK.
7Input selection
Select input source.
8Image adjustment
Adjust brightness, contrast and gamma.
Press this button while holding the ALT button down to switch red, green and blue
channels on and off.
9Lens presets
To recall a lens preset, press and hold LOAD, then press a number button 1to 5.
To save a lens preset, press and hold SAVE, then press a number button 1to 5.
10 Remote control backlight ON / OFF
Make the remote control buttons glow in the dark, or switch this feature off.
continues on next page...
Notes
Only the controls shown highlighted
are used on this projector.
For more information about
LENS ADJUSTMENT mode, see
Adjusting the lens further in this
guide.
Input selection buttons:
• 1, 4, 5, 6, 7and 8- as labeled.
• 2selects the HDMI 1 input
• 3selects DVI 1
• ALT + 3 selects DVI 2
• 9selects HDMI 2
• 0selects HDMI 3
• 10+ selects Dual Pipe
• #selects HDBaseT
Presets only contain information
about the lens position. Focus and
zoom information is not kept.
Remote control
VGA HDMI DVI 3GSDI
CVBS1 SVIDEO
CLOSE
12 3 4
COMP CVBS2
5 6 7 8
9 0 10+ #
MAIN SUB DUAL HD-T
OFF ON
ALT ROLL
PITCH YAW
FOCUS CAL
SHIFT ZOOM
EYE
SWAP
MAIN/PIP
SWAP
BRI CON GAMMA 3D
ON/OFF
PIP
ON/OFF
LOAD SAVE TEST ADDR
BACKLIGHT
RGB
PRESET
SHUTTER
OPEN
POWER
MENU
OK
EXIT INFO
1
2
6
7
8
10
3
4
5
9

Digital Projection HIGHlite 660 3D Series REMOTE CONTROL Installation and Quick-Start Guide
8
Rev A December 2013
Remote control - continued from previous page
11 Lens controls
Adjust position, zoom and focus.
12 INFO
Open the Information menu.
13 TEST
Switch to test pattern.
14 IR address
Set up an address to match the IR address of a projector.
Notes
Only the controls shown highlighted
are used on this projector.
For more information about IR
addresses, see Setting up an IR
address in the Operating Guide.
Remote control
VGA HDMI DVI 3GSDI
CVBS1 SVIDEO
CLOSE
12 3 4
COMP CVBS2
5 6 7 8
9 0 10+ #
MAIN SUB DUAL HD-T
OFF ON
ALT ROLL
PITCH YAW
FOCUS CAL
SHIFT ZOOM
EYE
SWAP
MAIN/PIP
SWAP
BRI CON GAMMA 3D
ON/OFF
PIP
ON/OFF
LOAD SAVE TEST ADDR
BACKLIGHT
RGB
PRESET
SHUTTER
OPEN
POWER
MENU
OK
EXIT INFO
11
14
13
12

Digital Projection HIGHlite 660 3D Series REMOTE CONTROL Installation and Quick-Start Guide
9
Rev A December 2013
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance
when trying to control the projector.
40°
40°
Infrared reception
Notes
Infrared reception is conrmed by
the blue IR LED ashing on the
control panel.
The infrared receivers are disabled
when a remote control is connected
via a cable. For more information,
see Wired remote control in the
Connection Guide.

Digital Projection HIGHlite 660 3D Series POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
10
Rev A December 2013
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for
viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance
from the screen for the image to ll the screen. Set the
adjustable feet so that the projector is level, and perpendicular
to the screen.
The drawing below shows the positions of the feet for table
mounting, and the xing holes for ceiling mounting.
1Four adjustable feet
2Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm into
the body of the projector.
1
2
1
1
1
2
2
2
2
2
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 30
cm (12 in) of space between the
ventilation outlets and any wall,
and 10 cm (4 in) on all other
sides.
Do not stack more than 3
projectors.
Do not tilt the projector more than
±12° from side to side when in
use, as this may cause serious
lamp failure, damage the lamp
module and cause extra cost on
replacement.
±12° 360°

Digital Projection HIGHlite 660 3D Series CHANGING THE LENS Installation and Quick-Start Guide
11
Rev A December 2013
Changing The Lens
Inserting a new lens
1. Remove the six screws 1securing the front cover to the body of
the projector.
2. Remove the front cover 2from the projector.
3. Remove the lens from its packaging and remove the two protective
caps from the front and back of the lens.
4. Insert the lens 3into the lens aperture, making sure that the plug
on the zoom drive mechanism lines up with the socket 4on the
right of the lens aperture.
5. Push the lens in rmly as far as it will go.
6. Rotate the lens clockwise as far as it will go.
7. Replace the front cover and secure it with the six screws.
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.
2
1
4
3

Digital Projection HIGHlite 660 3D Series CHANGING THE LENS Installation and Quick-Start Guide
12
Rev A December 2013
Removing the lens
1. Remove the six screws 1securing the front cover to the body of
the projector.
2. Remove the front cover 2from the projector.
3. Push down the lens holder tab 3.
4. Rotate the lens anti-clockwise
5. Pull the lens forward to remove it from the lens aperture.
2
1
3
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.