Digital Projection E-Vision Laser 15000 Series Datasheet

Rev B April2021
E-Vision Laser 15000 Series
High Brightness Digital Video Projector
INSTALLATION & QUICK START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REFERENCE GUIDE
121-000B

DigitalProjection E-Vision Laser15000 Series Introduction
Introduction
Congratulations on your purchase of this Digital Projection product. Your projector has the following key features:
lWUXGA native resolution delivering 15,000 ISO lumens.
lSupport for Frame Sequential 3D.
lSupport for Dual Pipe 3D format.
lHDBaseT® for transmission of uncompressed High Definition Video up to 100 m from the source.
l3G-SDI with loop-through.
lEdge Blend with black level correction.
lRed laser assist for enhanced color fidelity.
lBlanking control for custom input window sizing.
lCornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.
lControl via LAN HDBaseT and RS232.
lMotorised lens mount with Shift, Zoom and Focus using compatible lenses.
lSeparate control of screen and source aspect ratio.
A serial number is located on the side of the projector. Please record it here for future reference:
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Rev B April2021
page 2
Introduction
Notes

Aboutthis document DigitalProjection E-Vision Laser15000 Series
About this document
Symbols used in this document
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely followed.
LIGHT HAZARD WARNING: this symbol indicates that there is a danger of exposure to intensive light that may result in personal injury unless the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specifications and designs, and add new features without prior
notice.
Additional Documentation
Updates to this manual may be available online.
Please use the QR code (also located on the projector) to access the latest E-Vision projector user guides and other documentation via the Digital
Projection website.
Or visit the products specification page on the Digital Projection website to download the latest user guide and other documentation.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners. Digital Projection disclaims any proprietary interest in
trademarks and trade names other than its own.
Copyright © 2021 Digital Projection All rights reserved.
Third Party Credits
Art-NetTM Designed by and Copyright Artistic License Holdings Ltd.
Introduction Rev B April2021
page 3
Notes

DigitalProjection E-Vision Laser15000 Series Electrical and PhysicalSpecifications
Electrical and Physical Specifications
Mains Voltage 200-240 VAC 8.2A 50/60Hz
100-130 VAC 11.9A 50/60Hz
Operating Temperature 0°C to 35°C (32°F to 95°F), 35°C to 40°C (95°F to 104°F) with reduced light output
Storage Temperature -20°C to 60°C (-4°F to 140°F)
Operating Humidity 10% to 90% non-condensing
Storage Humidity 10% to 90% non-condensing
Dimensions L:598.3mm (23.55in) X W: 500mm (19.68in) X H 218.5mm (8.6in)
Weight 29.5 kg (65 lb) without lens
Power Consumption at 110 VAC: 1025 W (Normal mode)
at 110 VAC: 990 W (Eco mode)
at 110 VAC: 1070 W (High Altitude mode)
at 240 VAC: 1570 W (Normal mode)
at 240 VAC: 1165 W (Eco mode)
at 240 VAC: 1590 W (High Altitude mode)
Standby Power < 0.5W (Network Off), < 6W (Network On)
Thermal Dissipation at 110 VAC: 3497 BTU/hr (Normal mode)
at 110 VAC: 3378 BTU/hr (Eco mode)
at 110 VAC: 3650 BTU/hr (High Altitude mode)
at 240 VAC: 5357 BTU/hr (Normal mode)
at 240 VAC: 3975 BTU/hr (Eco mode)
at 240 VAC: 5425 BTU/hr (High Altitude mode)
Fan Noise 48 dBA Max, 46 dBA Typical (Normal mode)
45 dBA Max, 43 dBA Typical (Eco mode)
59 dBA Max, 57 dBA Typical (High Altitude mode)
48 dBA Max, 46 dBA Typical (High Altitude Quiet mode)
Specifications are subject to change without notice.
Laser Parameters
Wavelength (Red) 635nm - 647nm
Wavelength (Blue) 450nm - 460nm
Mode of operation Pulsed, due to frame rate
Pulse duration (Red) 1.6ms
Pulse duration (Blue) 0.87ms
Maximum pulse energy (Red) 0.72mJ
Maximum pulse energy (Blue) 0.45mJ
Rev B April2021
page 4
Introduction
Notes

Compliance with InternationalStandards DigitalProjection E-Vision Laser 15000 Series
Compliance with International Standards
RF Interference
FCC
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by Digital Projection in this manual.
Failure to comply with this government regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant with Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for
correcting any interference.
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 48 dB (A) at normal operating mode according to ISO 3744 or ISO 7779.
European Waste Electrical and Electronic Equipment (WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and Electronic Equipment. Our products are designed with reuse, recycling and
recovery of all components in mind. To this end, at end of life, your projector may be returned to Digital Projection Ltd or its agent so that the
environmental impact can be minimised.
Introduction Rev B April2021
page 5
Notes

DigitalProjection E-Vision Laser15000 Series Contents
Introduction 2
About this document 3
Symbols used in this document 3
Product revision 3
Additional Documentation 3
Legal notice 3
Third Party Credits 3
Electrical and Physical Specifications 4
Laser Parameters 4
Compliance with International Standards 5
RF Interference 5
Noise 5
European Waste Electrical and Electronic Equipment (WEEE) Directive 5
Contents 6
General Precautions 10
What's in the box? 12
Projector overview 13
Location of Laser Aperture 14
Interlock Switches 15
Installation Precautions 16
Laser Safety Precautions 19
Risk Group 3 Laser Hazard Installation Precautions 20
Light Hazard Warning 20
Light Hazard Distance and Hazard Zone 20
Fitting a lens 21
Inserting a new lens 21
Removing the lens 22
Fitting a lens hood 23
Positioning the screen and projector 24
Power Supply 25
AC Power Precautions 25
Connecting the power supply 26
Voltage selection 26
Operating the projector 27
Control panel 27
Projector indicators 28
Remote control 29
Infrared reception 33
Switching the projector on 33
Switching the projector off 33
Interlock reset 33
Selecting an input signal 34
Selecting a test pattern 34
Adjusting the lens 35
Adjusting the image 35
Orientation 35
Geometry 35
Picture 35
Signal inputs 38
Digital inputs and outputs 38
EDID on the DisplayPort, HDMI, and HDBaseT inputs 39
Using DisplayPort / HDMI / HDBaseT switchers with the projector 39
Analog inputs and outputs 40
3D connections 41
3D frame packed, side-by-side and top and bottom formats 42
Frame sequential 42
Dual Pipe (Left/Right) 42
3D Sync 43
Control connections 44
LAN connection examples 45
RS232 connection example 46
Using the menus 48
Opening the Menu 48
Opening a submenu 48
Exiting menus and closing the OSD 49
Inside a menu 49
Accessing sub menus 50
Executing commands 50
Rev B April2021
page 6
Introduction
Notes
Contents

Contents DigitalProjection E-Vision Laser15000 Series
Editing projector settings 51
Using a slider to set a value 51
Editing numeric values 52
Using the projector 53
Main Menu 53
Lens menu 54
Lens control 54
Lens memory 55
Image 56
Position and Phase 57
Color 58
Color Space 58
Color Mode 59
ColorMax 59
Manual Color Matching 60
Color matching parameters explained 61
Color Temperature 62
Gains and Lifts 62
Geometry 63
Aspect Ratio 63
Theaterscope setting 64
Digital Zoom 65
Overscan 66
Blanking 67
Keystone 68
4 Corners 71
Top right corner example 72
Rotation 73
Rotation example 74
Pincushion / Barrel 75
Pincushion/ Barrel example 75
Arc 76
Custom Warp 77
Warp Filter 78
Edge Blend 79
Blend Start 80
Blend Width 81
Black Level Uplift 82
3D 83
3D types 84
Some 3D settings explained 85
Dark Time 85
Eye Swap 85
Sync Offset 86
Laser 87
Setup 88
ColorMax 90
Measured data/ target data 90
Power on/off 91
Clock Adjust 92
OSD Settings 92
Memory 93
Network 94
Network Setup 94
Art-Net Setup 95
Art-Net Channel Setting 95
PIP 96
Information 97
Signal Format 97
System Status 98
Thermal Status 98
Factory Reset 99
Served web pages 100
Appendix A: Product labels 110
Projector 110
Label Locations 111
Projector 111
Appendix B: Choosing a lens 112
Basic calculation 113
Basic calculation example 114
Full lens calculation 115
Introducing TRC 115
Calculating TRC 116
TRC table 116
Calculating the throw ratio with TRC 116
Full lens calculation example 117
Appendix C: Screen requirements 118
Fitting the image to the display 118
WUXGA images displayed full width 118
Introduction Rev B April2021
page 7
Notes

DigitalProjection E-Vision Laser15000 Series Contents
WUXGA images displayed with a height of 1200 pixels 118
WUXGA images displayed full height 119
Diagonal screen sizes 119
Appendix D: Positioning the image 120
Appendix E: Aspect ratios explained 121
Aspect ratios examples 121
Source: 4:3 121
Source: 16:9 122
Source: 16:10 (native) 122
Aspect ratio example: TheatreScope 123
Appendix F: Supported signal input modes 124
2D formats 124
3D formats 127
Appendix G: Wiring details 130
Signal inputs and outputs 130
HDMI 130
DisplayPort 131
3G-SDI in, 3G-SDI out 132
HDBaseT input 132
DVI-D input 133
VGA input 134
Control connections 134
LAN 134
RS232 135
Trigger 135
Appendix H: Glossary of terms 136
Rev B April2021
page 8
Introduction
Notes

Rev B April2021
E-Vision Laser 15000 Series
High Brightness Digital Video Projector
INSTALLATION & QUICK START GUIDE
121-000B

DigitalProjection E-Vision Laser15000 Series GeneralPrecautions
General Precautions
Warning! Death or Serious Injury could occur if the following precautions are ignored
Eye Hazard! Do not look directly into the lens when the light source is on. The high brightness can cause permanent eye damage
Fire Hazard! Keep any combustible material away from hot surfaces and the projected beam. Ensure cables do not contact hot surfaces
Shock Hazard! Use only authorised components, tools, accessories and replacement parts specified by the manufacturer
Trip Hazard! Locate cables where they cannot be pulled, tripped over or damaged by persons or objects
Operate the product in the specified operating environment and conditions
Product should be powered off and disconnected from the mains before any service or maintenance operation
Keep body parts, hair, clothing and jewellery away from moving parts in the product.
Do not operate the product without a lens installed
Use a lens plug when installing or moving the product
The unit is never to be operated if the unit is defective or the cover or seal is damaged.
No maintenance allowed by end user.
Do not open the cabinet. There are no user serviceable parts inside.
No service is allowed except by authorized personnel.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this equipment MUST be earthed.
Take care to prevent small objects such as paper or wire from falling into the projector. If this does happen, switch off immediately, and have the
objects removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any liquids on top of the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a damaged power cable.
Rev B April2021
page 10
Introduction
Notes