Digital Projection INSIGHT 4K Dual LED Series User manual

Rev C June 2016
INSIGHT 4K Laser Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICK-START GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
116-355C

page i
Digital Projection INSIGHT 4K Laser Series
Rev C June 2016
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2016 Digital Projection Ltd. All rights reserved.
Notes

page ii
Digital Projection INSIGHT 4K Laser Series
Rev C June 2016
Laser Information
Caution-useofcontrolsoradjustmentsorperformanceofproceduresotherthanthosespeciedhereinmayresultin
hazardous radiation exposure.
Notes
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
455-470nm <13Watts
CLASSIFIED EN/IEC 60825-1 2007

page iii
Digital Projection INSIGHT 4K Laser Series
Rev C June 2016
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• 4K resolution up to 60 fps via single DisplayPort input.
• Dual Pipe input capability (2 x DisplayPort 1.2).
• Full 4K 3D display capability.
• Scaling of HDMI 1.4 formats to 4K resolution.
• 3G-SDI.
• Blanking control for custom input window sizing.
• Control via LAN and RS232.
• Motorised lens mount.
A serial number is located on the product label. Record it here:
Notes

page iv
Digital Projection INSIGHT 4K Laser Series
Rev C June 2016
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
CONNECTING THE POWER SUPPLY ............................................. 3
PROJECTOR OVERVIEW ............................................................... 4
Front and rear views ............................................................................. 4
Control panel......................................................................................... 5
Control panel button indicators ............................................................. 6
Status indicators.................................................................................... 7
POSITIONING THE SCREEN AND PROJECTOR............................. 8
Tilting restrictions .................................................................................. 9
FITTING THE LENS...................................................................... 10
CLEANING AND REPLACING THE FILTERS ................................ 11
Rear lters........................................................................................... 11
Front lter............................................................................................ 13
Reset the air lter usage time ............................................................. 15
OPERATING THE PROJECTOR.................................................... 16
Switching the projector on................................................................... 16
Switching the projector off................................................................... 17
Selecting a title or test pattern............................................................. 18
Selecting a title.................................................................................... 18
Selecting a test pattern.......................................................................... 19
Adjusting the lens................................................................................ 20
Adjusting the brightness...................................................................... 21
CONNECTION GUIDE ............................................................................23
SIGNAL INPUTS .......................................................................... 25
Main connections panel ...................................................................... 25
3D Sync ............................................................................................ 26
Indicators on the main connections panel................................................... 27
Option board ....................................................................................... 28
EDID on the DVI, HDMI and DisplayPort inputs ................................. 29
Using HDMI/DVI/DisplayPort switchers with the projector............................... 29
CONTROL CONNECTIONS........................................................... 30
OPERATING GUIDE ................................................................................31
USING THE CONTROL PANEL ..................................................... 33
LCD display overview.......................................................................... 33
In STANDBY mode .............................................................................. 33
In operation........................................................................................ 33
When showing menus........................................................................... 34
Locking and unlocking the control panel............................................. 35
Working with menus........................................................................... 36
Entering alphanumeric values ................................................................. 36

page v
Digital Projection INSIGHT 4K Laser Series
Rev C June 2016
USING THE PROJECTOR............................................................. 37
Title Select menu ................................................................................ 37
Selecting a test pattern.......................................................................... 37
Conguration menu............................................................................. 38
Light Setup ........................................................................................ 38
Lens Control....................................................................................... 38
Reset................................................................................................ 38
Information menu ................................................................................ 39
Light Output ....................................................................................... 39
Preset Button...................................................................................... 39
Usage............................................................................................... 39
Error Code ......................................................................................... 39
Version ............................................................................................. 40
IP Address ......................................................................................... 41
Setup Date......................................................................................... 41
Option Status...................................................................................... 41
REFERENCE GUIDE................................................................................43
THE DMD™.................................................................................. 45
CHOOSING A LENS ..................................................................... 47
SCREEN REQUIREMENTS........................................................... 48
Fitting the image to the DMD™........................................................... 48
Diagonal screen sizes......................................................................... 49
Fitting the image to the screen............................................................ 50
Positioning the screen and projector................................................... 51
POSITIONING THE IMAGE........................................................... 52
Maximum offset range......................................................................... 54
ASPECT RATIOS EXPLAINED...................................................... 55
APPENDIX A: LENS PART NUMBERS.......................................... 56
APPENDIX B: LENS CHARTS ...................................................... 57
How to use the lens charts ..................................................................... 57
Lens chart, up to 100 m throw ................................................................. 58
Lens chart, 10 m throw in detail ............................................................... 59
APPENDIX C: SUPPORTED SIGNAL INPUT MODES .................... 60
ICP60 .................................................................................................. 60
Option board ....................................................................................... 61
Screen allocation of Option board input signals ........................................... 62
APPENDIX D: MENU MAP............................................................ 63
APPENDIX E: WIRING DETAILS................................................... 65
Signal inputs - main connections panel............................................... 65
HDMI................................................................................................ 65
DisplayPort ........................................................................................ 66
Signal inputs - option board ................................................................ 67
DVI .................................................................................................. 67
3G-SDI In .......................................................................................... 68
Control connections ............................................................................ 69
LAN ................................................................................................. 69
RS232 .............................................................................................. 69
3D Sync IN and 3D Sync OUT ................................................................ 69
APPENDIX F: GLOSSARY OF TERMS.......................................... 70
CONTENTS (continued)

page vi
Digital Projection INSIGHT 4K Laser Series
Rev C June 2016
APPENDIX G: EARLIER VERSIONS ............................................. 79
How to check the version of your projector......................................... 79
Lens assembly and tting.................................................................... 80
Assembling the lens ............................................................................. 80
Inserting a new lens ............................................................................. 82
Removing the lens ............................................................................... 85
Lens part numbers .............................................................................. 87
TECHNICAL SPECIFICATIONS .................................................... 88
Models................................................................................................. 88
Inputs and outputs............................................................................... 89
Bandwidth ........................................................................................... 89
Remote control and keypad ................................................................ 89
Automation control .............................................................................. 89
Color temperature ............................................................................... 89
Lenses................................................................................................. 90
Lens mount ......................................................................................... 90
Mechanical mounting .......................................................................... 90
Orientation........................................................................................... 90
Electrical and physical specications.................................................. 91
Safety & EMC regulations................................................................... 91
CONTENTS (continued)

Digital Projection INSIGHT 4K Laser Series
This page is intentionally left blank.

Rev C June 2016
INSIGHT 4K Laser Series
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE
4

Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
IN THIS GUIDE
Rev C June 2016
IN THIS GUIDE
Connecting The Power Supply........................................................................ 3
Projector Overview............................................................................................. 4
Front and rear views ...................................................................................................4
Control panel ...............................................................................................................5
Control panel button indicators.................................................................................6
Status indicators .........................................................................................................7
Positioning The Screen And Projector......................................................... 8
Tilting restrictions.......................................................................................................9
Fitting The Lens ................................................................................................ 10
Cleaning And Replacing The Filters ........................................................... 11
Rearlters .................................................................................................................11
Frontlter ..................................................................................................................13
Resettheairlterusagetime ..................................................................................15
Operating The Projector ................................................................................. 16
Switching the projector on.......................................................................................16
Switching the projector off.......................................................................................17
Selecting a title or test pattern.................................................................................18
Selecting a title................................................................................................................18
Selecting a test pattern ...................................................................................................19
Adjusting the lens .....................................................................................................20
Adjusting the brightness..........................................................................................21

page 3
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Rev C June 2016
Connecting The Power Supply
When the projector is viewed from the back, the AC mains
inlet 1is located on the right hand side, toward the rear.
Make sure the power switch 2above the inlet is in the
OFF position, then push the mains connector in rmly.
12
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.

page 4
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C June 2016
Projector Overview
Front and rear views
1 Airinletandlter
2SYSTEM status indicator
When the projector is operating normally, this
indicator lights green or orange. If an error
occurs, the light becomes red. Depending on the
scenario, the light can be steady or ashing.
3LIGHT status indicator
Turns on when the light source is switched on.
4Lens
5Air outlet
6 Airinletandlter
7Air outlet
8Power switch and power connection
9Control panel with LED screen
10 Connections
10 Adjustable feet
Notes
Front view
4
32
5
1
Rear view
11
7 86
11
9 10 10

page 5
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C June 2016
Control panel
1LCD display
2KEY LOCK button (with indicator)
3Arrow buttons
4MENU button
5ENTER button
6not used in this conguration
(except for entering alphanumeric values)
7LIGHT button
8not used in this conguration
9POWER button (with indicator)
10 EXIT button
11 DOUSER button (with indicator)
12 LIGHT ON / OFF button (with indicator)
13 not used in this conguration
14 Preset buttons 1 to 8 (with indicators)
Notes
See Entering alphanumeric values
in the Operating Guide.
1
10
4
7
14
3
6
2
9
12
13
8
11
5

page 6
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C June 2016
Control panel button indicators
1KEY LOCK
Behavior Meaning
Off Key lock is inactive.
On Key lock is activated.
2POWER ON / OFF
Behavior Meaning
Off
The projector is switched off from the power supply
or in STANDBY mode.
Flashing
green
The projector is warming up (preparing to switch ON)
or cooling down (preparing to switch OFF).
Steady
green The projector is switched on.
3DOUSER ON / OFF
Behavior Meaning
Off The douser is opened.
Steady
green The douser is closed.
4LIGHT ON / OFF
Behavior Meaning
Off The light source is switched off.
Steady
green The light source is switched on.
5Presets
Behavior Meaning
Off The title is not assigned to the projector.
Steady
white
The title is assigned to the projector but is not
currently in use.
Steady
green
The title is assigned to the projector and is currently
in use.
Notes
1
5
4
2
3

page 7
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C June 2016
Status indicators
1LIGHT status indicator
Behavior Meaning
Off The light source is switched off.
On The light source is switched on.
2SYSTEM status indicator
Behavior Meaning
Off The projector is switched off.
Flashing green The projector is warming up. The douser is closed and the light source is off.
Steady green The projector is switched on.
Flashing amber The projector is cooling down.
Steady amber The projector is in standby.
Flashing red Error, projection cannot continue. Check LCD screen for error message.
Flashing red, with buzzer Error with safety implications. Projection cannot continue. Check LCD screen for error message.
Steady red Nonfatal error, projection may continue. Check LCD screen for error message.
Notes
21

page 8
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev C June 2016
Positioning The Screen And Projector
Installation should be carried out by authorised personnel only.
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the screen.
The drawing below shows the bottom of the projector. The positions of the feet for table mounting, and the xing holes for ceiling mounting
are clearly visible. The illustration also shows the positions of the four handles which facilitate safe carriage.
1Four adjustable feet
2Six M6 holes for ceiling mount (set A)
The screws should not penetrate more than 15 mm into the
body of the projector.
3Handles for safe carriage
4Six M6 holes for ceiling mount (set B)
The screws should not penetrate more than 15 mm into the
body of the projector.
1
2
1
1
1
2
2
2
2
2
3
3
3
3
4
4
4
4
44
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 30
cm (12 in) of space between the
ventilation outlets and any wall,
and 10 cm (4 in) on all other
sides.
Projectors are not designed to
be stacked on top of each other
unless a rigging frame is used.

page 9
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev C June 2016
Tilting restrictions
The projector can be operated in numerous positions.
The only non-workable angles are:
• Upright mode with lens pointing upward.
• Portrait mode with inputs facing downward.
The diagram below illustrates both positions showing non-workable angles 1and workable angles 2:
Notes
Portrait mode installation requires
ttingasafetyguardunderneath
the projector (as shown in the
illustration below). Unauthorised
personnel should not attempt to
carry out portrait mode
installation. Please contact Digital
Projection or a dealer if you wish
to use the projector in portrait
mode.
Pointing Up
30°
330° 2
130°
330° 2
1
Roll (Portrait)

page 10
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
FITTING THE LENS
Rev C June 2016
Fitting The Lens
1. Insert the lens into the mount.
Engage the three locating studs 1into
the corresponding slots 2on the mount.
2. Rotate the lens clockwise until the studs
slide all the way into the slots.
3. Tighten the two xing screws 3on the
lens collar.
1 2
3
Notes
This procedure applies to version
Cof the projector. If your projector
is an earlier version or if you are
unsure which version you have,
see Appendix G in the Reference
Guide.
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.
The projector will not power on
without the lens tted.
Before turning on the projector,
please ensure the protective caps
are removed from the front and rear
of the lens.
Thetwoxingscrewsmustbe
tightened to at least a torque
of 0.5 N-m using a screwdriver.
Loose screws might lead to the
lens falling off.
When a new lens is tted, a
calibration procedure must be
carried out. For more information,
see Calibrating zoom and focus
further in this guide.

page 11
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
CLEANING AND REPLACING THE FILTERS
Rev C June 2016
Cleaning And Replacing The Filters
Rear lters
1. Loosen the two knobs 1 holding the lter cover by turning them
counterclockwise.
Use a Phillips screwdriver if necessary.
2. Tilt the lter cover to open it.
3. Remove the lters. Grasp the top and bottom or left and right ends of
each air lter and remove it by pulling toward you.
Notes
The knobs are captive on the
removable cover.
Beforechangingthelters,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
Whenchangingthelters,avoid
using excessive force as this may
damage the equipment.
Filters should be replaced when
new light sources are tted, or as
necessary upon visual inspection
and in accordance with operating
environment.
1
1
3

page 12
Digital Projection INSIGHT 4K Laser Series
Installation and Quick-Start Guide
CLEANING AND REPLACING THE FILTERS
Rev C June 2016
4. If you are replacing the lters, skip this step.
To clean the lters, use a vacuum cleaner brush attachment to vacuum
away dust from the air lters. Avoid making direct contact without an
attachment or using a nozzle attachment.
5. Mount the air lters to the projector. Look for an arrow (AIR FLOW↑)
indicating the installation direction on the side of the air lter. Point the
arrow towards the projector.
6. Close the lter cover.
7. Tighten the knobs clockwise to secure the cover.
Notes
Beforechangingthelters,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
Whenchangingthelters,avoid
using excessive force as this may
damage the equipment.
Filters should be replaced when
new light sources are tted, or as
necessary upon visual inspection
and in accordance with operating
environment.