Dimplex DXLWP800TI B User manual

Important Safety Advice
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of re, electrical shock, and
injury to persons, including the following:
IMPORTANT – The wall bracket supplied with
the appliance must be used.
WARNING – DO NOT USE THIS HEATER
IN THE IMMEDIATE SURROUNDINGS OF A
BATH, A SHOWER OR A SWIMMING POOL.
IMPORTANT – If the heater is installed in a
room containing a bath or shower, it must be so
installed that switches and other controls cannot
be touched by a person using a bath or shower.
Do not use outdoors.
Do not locate the heater immediately below a
xed socket outlet or connection box.
WARNING: In order to avoid overheating, do
not cover the heater. Do not place material
or garments on the heater, or obstruct the
air circulation around the heater, for instance
by curtains or furniture, as this could cause
overheating and a re risk.
NEVER cover or obstruct in any way the heat
outlet slots at the top of the heater or the air
inlet slots in the base of the heater.
The heater carries the Warning symbol
indicating that it must not be covered.
CAUTION - Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
This appliance can be used by children aged
from 8 years and above and by persons with
reducedphysical,sensoryormentalcapabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved.
Dimplex Low Wattage Panel Heaters
Models: DXLWP400, DXLWP400TI, DXLWP800,
DXLWP800TI N, DXLWP800TI B & ARLWP800TI
Installation and Operating Instructions
Dimensions
(millimetres)
Models  Specication
DXLWP400 400W Neon Heat Switch
DXLWP400TI 400W Neon Heat Switch / 24 Hour Timer
DXLWP800 800W Neon Heat Switch
DXLWP800TI N 800W Neon Heat Switch / 24 Hour Timer
DXLWP800TI B 800W ON/OFF, 2 Switches/ 24 Hour Timer
ARLWP800TI 800W 2 Neon Heat Switches / 24 Hour Timer
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
600 mm - 400W
800 mm - 800W
500 mm
INDUKLWPRG Issue 13
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
Children of less than 3 years should be kept
away unless continuously supervised.
Children aged from 3 years and less than 8
years shall only switch on/off the appliance
provided that it has been placed or installed in
its intended normal operating position and they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance
or perform user maintenance.
Note that due care and consideration must be
taken when using this heater in series with a
thermal control, a program controller, a timer
or any other device that switches on the heat
automatically, since a re risk exists when the
heater is accidentally covered or displaced.
If the supply cord is damaged it must be
replaced by the manufacturer or service agent
or a similarly qualied person in order to avoid
a hazard.
WARNING: Servicing and product
repairs should only be undertaken by the
manufacturers approved service agent or a
similarly qualied person, using only exact
manufacturer approved spare parts.
WARNING: This heater is not equipped with
a device to control the room temperature.
Do not use this heater in small rooms when
they are occupied by persons not capable
of leaving the room on their own,
unless constant supervision is provided.

Installation
The Fixing Kit should contain: 1 Drilling Template, 3 Screws, 3
Rawlplugs and 1 Mounting Bracket.
Wall Mounted Operation (see Fig. 2)
Suggested Fixings
SOLID BRICK/BLOCK: No. 8 Rawlplug inserts, 6mm drill bit.
PLASTERBOARD: If possible locate studding and use No. 8
woodscrews directly into the wood, otherwise M5 rawlplug intersets
are suitable.
NOTE: FOR OTHER WALL TYPES (e.g. Timber frame and hollow
concrete) SEEK SPECIALIST ADVICE.
1. Select the position for the heater ensuring there is
clearance from any furniture and ttings of at least
150mm above the heater, 50mm below, 25mm each
side and 300mm from the front panel. Curtains must
not be closer than 150mm from the top and/or sides of
the heater.
2. Position the drilling template provided on the wall ensuring
it is level. Mark the position of the relevant holes on the
wall at the edge of template. Before drilling check that the
distance between the hole centres is correct, 340mm for
400W Models and 540mm for 800W models (see Fig. 2).
Fig. 2
Positioning the Heater
Select the position for the heater ensuring there is clearance
fromanyfurnitureandttingsofatleast150mmabovethe
heater, 50mm below (wall mounted), 25mm each side and
300mm from the front panel. Curtains must not be closer than
150mm from the top and/or sides of the heater.
Free Standing Operation (see Fig. 1)
NEVER USE THE HEATER FREE STANDING WITHOUT THE
FEET FITTED (FEET ARE PACKED SEPARATELY IN CARTON).
1. Lay the heater on its front.
2. Remove the two star head screws from the base of the
heater using a x-head screwdriver.
3. Place feet over base of heater, align holes and engage hook
on foot into the recess on the back of the heater - see Fig.
1.
4. Replace the screws but do not overtighten.
Fig. 1
Rear View 3. Drill the wall at the three marked positions and t the wall
plugs.
Ensure template has been removed.
4. Fix two No. 8 screws to the top two holes leaving 3mm of
the screw exposed. Hang the heater on the screws.
5. Fit the bottom bracket, found in the xing kit, in the slot at
the base of the heater and screw the bracket to the wall.
Testthattheheaterisnowsecurelyxedtothewall.
130mm 340mm - 400W
540mm - 800W
95mm
150mm
50mm
420mm
25mm 25mm
130mm
Drilling Holes
Bracket
Electrical Connection
WARNING THIS APPLIANCE MUST BE EARTHED
If the socket outlets in your home are not of the 13 amp BS1363
type they will not accept the plug connected to this heater,
therefore cut off the plug. When cut off this plug can constitute
a shock hazard if inserted into a socket outlet. It must therefore
be disposed of safely.
Before wiring the appropriate plug please note that the wires in this
mains lead are coloured in accordance with the following code.
GREEN/YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
Connect the Green/Yellow wire to the terminal marked Eor the
earth symbol or coloured Green or Green/Yellow.
Connect the Brown wire to the terminal marked Lor coloured Red.
Connect the Blue wire to the terminal marked Nor coloured Black.
DO NOT connect the Brown (Live) or the Blue (Neutral) wires
to the Earth terminal of your 13 amp plug. If the terminals of the
plug are unmarked or you are in any doubt, consult a qualied
electrician.
CAUTION: If you use this heater in conjunction with a thermal
control, programme controller, timer or any other device which
switches the heater on automatically observe all safety warnings
at all times.
Please Note: Although this heater is manufactured to
comply with the relevant safety standards, certain types
of carpets could become discoloured by the temperatures
under a portable heater. If you are concerned about this,
we recommend that you contact the carpet manufacturer
for guidance. Alternatively, either stand the heater on a
suitable base to shield the carpet or wall mount it.

Models with Timer
DXLWP400TI, DXLWP800TI N, DXLWP800TI B &
ARLWP800TI
Set the I- - Oslide switch on the
timer (Fig. 4) to:
Position O - Heating Off
Position I - Manual operation
This setting allows power to the heater
uninterrupted by the timer settings. The
heat selector switch will control the output
(see ‘Using the heater’).
Position - ‘Auto’ operation
DO NOT disconnect this heater from the mains supply unless it is
being taken out of use (e.g. in summer or for storage), otherwise
the timer clock will stop.
Setting the time of day
To set the time of day, rotate the timer dial
clockwise (indicated by the arrow) until the
correct time of day is opposite the reference
mark (see Fig. 5).
The 24-hour clock is used: e.g. time shown for
3 pm is ‘15’ (15:00hrs).
Setting the ‘Auto’ ON and OFF times
To set the timer:
1. Using your nger tip or the tip of a
pencil, push in as many segments as
necessary around the dial, according to
the times you don’t require heat – see
Fig. 4. Each segment pushed in switches
the heater OFF for that part of the hour.
All other segments will be ON. For
example, Fig. 6 shows the timer set to
switch the heater ON between 7 am and
9 am and between 4 pm and 9.30 pm .
2. You can select as many ON periods as you like, within the
24-hour day. The settings will repeat every day until changed.
3. To change ON and OFF times, simply push in any ‘ON’ segments
you wish to cancel and pull out new ‘ON’ segments as required.
Switching to auto
Set the heat selector for the heat output required.
Check that the clock shows the correct time of day. Set the I - 
- O slide switch to (see Fig. 4) - the convector will switch ON
and OFF according to the timer settings (see Fig 5).
IMPORTANT NOTES
Remember to observe all safety warnings when operating the
heater on auto setting unattended or attended.
If the mains supply to the heater is interrupted, the timer clock
will stop until power is restored; reset the time of day to ensure
correct ON and OFF times.
Operation
IMPORTANT - OBJECTS OR CLOTHING MUST NOT BE
PLACED ON THIS HEATER.
Before using the heater ensure that all warnings and
instructions have been read carefully.
OPERATION - SINGLE RATED MODELS
Models:
DXLWP400, DXLWP400TI, DXLWP800, and DXLWP800TI N
Turn the heater on using the switch on the right side of the heater
- the switch will be illuminated.
OPERATION - DUAL RATED MODELS
The two switches on the side of the heater control the heat output.
ARLWP800TI
Both switches illuminated indicates maximum output.
Top switch only illuminated indicates 500W output on 800W
model.
Bottom switch only illuminated indicates 300W output on 800W
model.
DXLWP800TI B
Position O - OFF
Position I - ON
Both switches in Position I indicates maximum output.
Top switch only in Position I indicates 500W
output on 800W model.
Bottom switch only in Position I indicates 300W
output on 800W model.
Note: On models tted with a timer, at least one switch must be
illuminated or in Position I for the heater to operate.
MODELS WITH TIMER - (see Fig. 4)
DXLWP400TI and DXLWP800TI N - 1 Switch,
The switch on the side of the heater turns the heater on.
Note: This switch must be in the “on” position before the heater
will operate.
DXLWP800 TI B & ARLWP800TI - 2 Switches
The two switches on the side of the heater control the amount
of heat available as described above, (Operation - Dual Rated
Model).
NOTE: At least one switch must be in the ‘On’ position before the
heater will operate.
4.00 pm - 9.30 pm
7.00 am - 9.00 am
15
11
1
2
4
5
6
8
9
10
7
3
24
16
22
23
20
21
18
17
19
12
13
14
O
I
Fig. 4
9
8
I
10
O
Fig. 5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
17
16
17
18
19
20
21
22
23
24
O
I
Fig. 6
Fig. 3

Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powder or polish of any
kind on the body of the heater.
Allow the heater to cool, then wipe with a dry cloth to remove dust
and a damp cloth (not wet) to clean off stains. Be careful not to
allow moisture into the heater.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it
should not be disposed of with household waste.
Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice
in your country.
After Sales Service
Your product is guaranteed for three years from the date of
purchase.
Within this period, we undertake to repair or exchange this product
free of charge (subject to availability) provided it has been installed
and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales service you should contact our
customer services help desk on 0844 879 3588. It would assist
us if you can quote the model number, series, date of purchase,
and nature of the fault at the time of your call. The customer
services help desk will also be able to advise you should you need
to purchase any spares.
Please do not return a faulty product to us in the rst instance as
this may result in loss or damage and delay in providing you with
a satisfactory service.
Please retain your receipt as proof of purchase.
Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
[c] Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex UK Limited.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and
EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
UK customer help line 8.00am–5.00pm Mon-Fri and 8:30am-1.00pm Sat (October-March)
Customer S ervices: Tel. [phone]
Fax. [phone]
e-mail customer.[email protected] m
Republic of Ireland Tel. [phone]