Dimplex DIMPLEX ELECTRIC FIREPLACE User manual

PRACTICAL USER’S GUIDE
FOR THE
DIMPLEX ELECTRIC FIREPLACE
WITH REMOTE CONTROL
Valued Customer,
We are pleased that you have chosen to purchase an electric
fireplace manufactured by Dimplex North America Ltd.
Over the years, valuable memories will occur around the
warmth and comfort of your hearth. Thank you for allowing our
product to be the backdrop for those special moments.
Quality checked by:
Serial Number _________________
Model Number _________________
CAT Number __________________
7204820100REV03

QUICK REFERENCE GUIDE FOR THE DIMPLEX ELECTRIC
FIREPLACE
1. Before using the electric corner wall mounted fireplace verify:
• Are the circuit breakers for the unit on?
• Are the light bulbs loose? (to check, follow the instructions for
replacing the light bulbs under the maintenance section of this
manual)
2. The heater may emit a slight, harmless odor when first used. This
odor is a normal condition caused by the initial heating of internal
heater parts.
3. The information regarding the model of your unit can be found on the
rating plate located inside the unit on the top left hand corner above
the mirror.
4. If you have any questions or concerns regarding the operation of your
fireplace, contact Dimplex customer service at 1-888-DIMPLEX (1-888-
346-7539).

CONTENTS
PAGE 1 Important Instructions
PAGE 2 Model and Serial Number
Information
PAGE 3 Site selection and preparation
PAGE 5 Fireplace Installation
PAGE 6 Operation
PAGE 9 Maintenance
PAGE 12 Warranty

IMPORTANT INSTRUCTIONS
SAVE THESE INSTRUCTIONS
PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the following:
1. Read all instructions before using the corner wall mounted electric fireplace.
2. The heater is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. The trim around the heater outlet becomes hot during heater operation. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3
feet (0.9m) from the front of the unit.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever
the unit is left operating and unattended.
4. Always unplug the corner wall mounted electric fireplace when not in use.
5. Do not operate with a damaged cord or plug, or if the heater has malfunctioned, or if the wall
mounted electric fireplace has been dropped or damaged in any manner. Return heater to
authorized service facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. The corner wall mounted electric fireplace is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater where it may fall into a bathtub or other water
container.
8. Do not install the fireplace directly on carpet or a similar surface which may restrict air circulation
beneath the unit.
9. Do not run the cord under carpeting. Do not cover cord with throw rugs, runners, or the like.
Arrange cord away from traffic area and where it will not be tripped over.
10. To disconnect the unit, turn the controls off, then remove the plug from the outlet.
11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause
an electric shock or fire, or damage to the heater.
12. To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may become blocked.
13. All electrical heaters have hot and arching or sparking parts inside. Do not use in areas where
gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to
flammable vapors.
14. Do not modify this fireplace. Use it only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock or injury to persons.
15. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of
fire. However, if you have to use an extension cord, the cord shall be No.16 AWG minimum size
and rated not less than 1875 watts.
16. To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the
other). The plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do
not change the plug in any way. Avoid the use of an extension cord. Extension cords may overheat
and cause a risk of fire. If you must use an extension cord, the cord must be No. 16 AWG minimum
size and rated no less than 1875 watts.
17. Do not burn wood or other materials in the corner wall mounted electric fireplace.
18. Do not strike the glass front.
19. Always use a certified electrician should new circuits or outlets be required.
20. Always use properly grounded, fused and polarized outlets.
21. Disconnect all power supply before performing any cleaning, maintenance or relocation of the unit.
22. When transporting or storing the unit and cord, keep in a dry place, free from excessive vibration
and store so as to avoid damage.
NOTE: Procedures and techniques that are considered important enough to emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the
equipment.
WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of
fire, serious injury, illness or death.
1

Model Number
Serial Number
Model Number Label
Serial Number Label
Model Number Label
Serial Number Label
IMPORTANT INSTRUCTIONS
If you have any questions about our products please have the product model and serial
numbers available upon calling Dimplex customer service. To locate the model and serial
number labels see below. Record the Model Number, Serial Number, and CAT number on the
front cover of this manual for future reference.
Firebox Carton
2

SITE SELECTION AND PREPARATION
This section provides easy step by step instructions for selecting a location and preparing the
site to install the fireplace into:
• Existing Fireplace
• New wall construction
• Dimplex mantel surround kit or custom made mantel surround
NOTE
The fireplace insert comes completely assembled and
wired. Some tools may be required to prepare the
site and assembly/install the trim.
The dimensions of the fireplace insert are 26” wide
(66cm) X 22 ½” high (57.2cm) X 12” deep (30.5cm).
(FIGURE 1) You should allow ¼” (0.6cm) around the
fireplace insert for ease of installation.
This fireplace does not require any venting.
CAUTION
Clearance for air circulation beneath the fireplace insert is
provided by three rubber feet (FIGURE 1).
DO NOT INSTALL THE FIREPLACE INSERT
DIRECTLY ON CARPET OR SIMILAR SURFACES
WHICH MAY RESTRICT AIR CIRCULATION. If
installing the fireplace in a carpeted area, place a
one-piece, solid, flat surface under the fireplace
insert. Ensure that all four of the insert’s feet rest
securely on this surface.
EXISTING FIREPLACE INSTALLATION
1. Seal all drafts and vents with non-fibrous
insulation materials to prevent chimney debris
from falling into the fireplace insert. Do not
install into an existing fireplace that is prone to
leaks or dampness.
2. Cap the top of the chimney flue to prevent rain
from entering.
3. Plan your electrical power supply: (refer to
NOTE 1)
4. The power cord can run along the front of the
hearth to an outlet near the fireplace
(FIGURE 2).
FIGURE 1
FIGURE 2
3

NOTE
The fireplace insert must be installed on a hard
surface.
NOTE
A 15 AMP, 120 VOLT circuit is required. A dedicated
circuit is preferred but not essential in all cases. A
dedicated circuit will be required if, after installation,
the circuit breaker trips or fuse blows on a regular
basis when the heater is operating. Additional
appliances on the same circuit may exceed the
current rating of the circuit breaker.
WARNING
To prevent personal injury you should hire a
professional to cap the chimney flue or cut a hole in
the existing fireplace for wiring.
If you return your existing fireplace to its original use
(Example wood burning), it should be inspected by
the local building department prior to use to reduce
the risk of fire and personal injury.
NEW WALL CONSTRUCTION
1. Select a suitable location that is not susceptible to
moisture and is away from drapes, furniture and
high traffic.
2. Place the fireplace in the desired location to see
how it will look in the room.
3. Mark the desired location on the floor and store
the fireplace in a safe, dry and dust free location.
4. Use studs to frame an opening of 26 ½” wide X
23” high (67.3cm wide X 58.4cm high) allowing a
depth of 12” (30.5cm).
5. Plan your electrical power supply.
(refer to NOTE 1)
Option #1 - The power cord can be lead from behind
the trim and along the wall to an outlet near the
fireplace. (FIGURE 4)
Option #2 - A new outlet can be installed inside the
new frame construction. (if allowed by electrical
code). (FIGURE 5)
FIGURE 3
FIGURE 5
FIGURE 4
4

WARNING
Construction and Electrical Outlet wiring must
comply with local building codes and other
applicable regulations to reduce the risk of fire,
electrical shock and injury to persons.
WARNING
Do not attempt to wire your own new outlets or
circuits. To reduce the risk of fire, electric shock or
injury to persons, always use a licensed electrician.
MANTEL SURROUND KIT OR CUSTOM MADE
MANTEL SURROUND
1. Select a suitable location that is not susceptible to
moisture and is away from drapes, furniture and
high traffic.
2. Place the fireplace in the desired location to see
how it will look in the room.
3. For ease of electrical hook up you may wish to
locate the fireplace near an existing outlet. (refer
to NOTE 1)
4. Store the fireplace in a safe dry and dust free
location.
5. Assemble the mantel surround kit (refer to the
mantel assembly instructions) or construct the
custom surround with an opening of 26 ½” wide X
23” high (67.3cm wide X 58.4cm high) allowing a
depth of 12” (30.5cm).
FIREPLACE INSERT INSTALLATION
This section provides easy step by step instructions for installation of your fireplace.
1. Install Trim Kit to front of fireplace by positioning
trim then pushing straight forward against the
fireplace.
2. Make sure the unit is switched OFF (Refer to
operating instruction section).
3. Plug the fireplace into a 15AMP/120Volt outlet. If
the cord does not reach you may use a extension
cord rated for a minimum of 1875 WATTS.
4. Push the Fireplace into place so that the trim is
against the finished Mantel Surround or wall
surface. (FIGURE 6)
5. Level, if required with wood shims (not included)
(FIGURE 7).
FIGURE 7
FIGURE 6
5

OPERATION
This section will explain the function of each convenient control.
1. To access the controls, open the upper grill by pulling, near the top right hand side,
forward and down. (FIGURE 9)
2. To locate controls refer to FIGURE 10.
3. To conceal the controls during the operation, return the grill to its original upright
position.
6
WARNING
Ensure the power cord is not installed so that it is
pinched or against a sharp edge and ensure that
the power cord is stored or secured to avoid
tripping or snagging to reduce the risk of fire,
electric shock or injury to persons.
FIGURE 8
WARNING
The centre and left hand side of the grille will get
hot when the heater is operating. Take care to
always grasp the grille on the right hand side.
FIGURE 9

B
FIGURE 10
A. MAIN ON/OFF SWITCH
The ON/OFF SWITCH supplies power to all fireplace functions (Heater/Flame).
B. FLAME ACTION CONTROL
Turn the flame action control knob to adjust the flame speed to the desired level.
C. INTERIOR LIGHT CONTROL
Turn the interior light control knob to increase or decrease the brightness of the interior
light.
D. HEATER CONTROL SWITCH
Turn heater on or off.
E. HEATER THERMOSTAT CONTROL
To adjust the temperature to your individual requirements, turn the thermostat control
clockwise all the way to turn on the heater. When the room reached the desired
temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in
this position to maintain the room temperature at this setting. For additional heat, turn
clockwise until you hear the click again and the heater will turn on.
NOTE
The heater may emit a slight, harmless odor when first used. This odor is a normal condition
caused by initial heating of internal heater parts and will not occur again.
RESETTING THE TEMPERATURE CUTOFF SWITCH
This unit is equipped with a thermostat which controls the temperature of the room. It does
this by turning the heater on and off. The heater is protected with a safety device to prevent
overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will
not come back on without being reset. It can be reset by switching the main ON/OFF SWITCH
to OFF and waiting 5 minutes before switching the unit back on.
7
E
D
C
A