Dimplex VF5452L User manual

Owner’s Manual
6909410210
6909410110
6909680110
Model
VF5452L
VF2927L
VFA2927
7213460100R05
IMPORTANT SAFETY INFORMATION: Always read this manual rst
before attempting to install or use this Opti-V . For your safety, always
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
To view the full line of Dimplex products, please visit
www.dimplex.com

2 www.dimplex.com
Table of Contents
Always use a qualied technician
or service agency to repair
this Opti-V.
!NOTE: Procedures and
techniques that are considered
important enough to emphasize.
CAUTION: Procedures and
techniques which, if not carefully
followed, will result in damage to
the equipment.
WARNING: Procedures
and techniques which, if not
carefully followed, will expose
the user to the risk of re,
serious injury, or death.
Welcome & Congratulations ..................3
IMPORTANT SAFETY INSTRUCTIONS.........4
Opti-V Installation ..........................6
Locating the Opti-V .........................6
Hardwire Installation ........................6
Operation ................................10
Maintenance .............................12
Warranty................................13
Technical Support .........................15

3
MADEIN IRELAND
FAITEN IRLANDE
HECHOEN IRLANDA
MODEL
MODELE
MODELO
CAT.#
No.de Cat.
PROTECTEDBY THE FOLLOWING PATENTS / PROTEGE PAR LES BREVETS SUIVANTS/PROTEGIDO POR LAS SIGUIENTES
PATENTES: US PATENTS / BREVETS DE ETATS UNIS / PATENTES DE ESTADOS UNIDOS : 8,361,367
OTHERPATENTS PENDING / AUTRES BREVETS EN INSTANCE / OTRAS PATENTES PENDIENTES
DIMPLEXNORTH AMERICA
1367INDUSTRIAL ROAD
CAMBRIDGE,ON, N1R 7G8
CANADA
6909410100
VF2927L
100-240V ~, 50/60HZ, 35W
Intertek
North America Limited
xxxxxxx
SERIAL No./No DE SERIE/No DE SERIE
DDDYYSLF - XXX
Welcome & Congratulations
Model Number
Serial Number
Thank you and congratulations for purchasing an Opti-V from Dimplex.
Please use our convenient online registration page to record your
model and serial numbers for future reference at
www.dimplex.com/register
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
In order to better serve you, please have your model and serial number
ready or register your product online before calling (See above)
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in
a possible electric shock, re hazard and will void the warranty.

4 www.dimplex.com
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances,
basic precautions should always be
followed to reduce the risk of fire,
electric shock, and injury to persons,
including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near
water.
6. The appliance shall not be
exposed to dripping or splash-
ing and that no objects lled with
liquid, such as vases, shall be
placed on the apparatus.
WARNING: To reduce the risk of
re or electric shock, do not expose
this apparatus to rain or moisture.
7. Clean only with dry cloth.
8. Do not block any ventilation open-
ings. Install in accordance with the
manufacturer’s instructions.
9. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other ap-
paratus (including ampliers) that
produce heat.
10. No naked ame sources, such as
candles should be placed on this
apparatus.
11. Only use attachments/accessories
specied by the manufacturer.
12. Use only with the cart, stand, tri-
pod, bracket, or table specied by
the manufacturer, or sold with the
apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
13. Disconnect power at the service
panel during lightning storms or
when unused for long periods of
time.
14. Refer all servicing to qualied
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the ap-
paratus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
15. If the appliance is damaged,
check immediately with the
supplier before installation and
operation.
16. Do not operate any unit with a
damaged cord, or if the Opti-V
has been dropped or damaged
in any manner, contact Dimplex
Technical Service at
1-888-346-7539.
17. Do not modify the Opti-V. Use it

5
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
only as described in this manual.
Any other use not recommended
by the manufacturer may cause
re, electric shock or injury to
persons.
18. When transporting or storing the
unit and cord, keep in a dry place,
free from excessive vibration and
store so as to avoid damage.
19. Do not install the remote control
battery backwards; charge; put
in excessive heat such as re,
sunshine or the like; or mix with
used or other battery types - may
explode or leak causing injury.
20. When replacing the battery
ensure that it is replaced with
alkaline 1.5 Volt (AAA) batter-
ies. Battery must be recycled or
disposed of properly. Check with
your Local Authority or Retailer for
recycling advice in your area.
!NOTE: To disconnect from mains
- set the mains switch to 'O'. The
mains (power) switch is located at
the top left hand side of the appliance
above the manual controls - see 'O/I'
Figure 2. Mains switch shall remain
readily operable.
WARNING: To prevent injury, this
apparatus must be securely attached
to the oor/wall in accordance with
the installation instructions.
WARNING: Remote control con-
tains small batteries. Keep away from
children. If swallowed, seek medical
attention immediately.
!NOTE: Changes or modications
not expressly approved by the party
responsible for compliance could void
user's authority to operate the equip-
ment.

6 www.dimplex.com
Opti-V Installation
WARNING: ANY INSTAL-
LATION AND SERVICE WORK
CAN ONLY BE PERFORMED BY
QUALIFIED AND AUTHORIZED
PERSONNEL. ALL INSTALLA-
TIONS MUST COMPLY WITH
ALL LOCAL CODES AND BY-
LAWS, AND INSPECTED AND
APPROVED FOR OPERATION
BY LOCAL GOVERNING AU-
THORITY PRIOR TO USE.
WARNING: Construction
and electrical outlet wiring must
comply with local building codes
and other applicable regulations
to reduce the risk of re, electric
shock and injury to persons.
Locating the Opti-V
The Opti-V uses an illusory reec-
tion technique and is designed
to work best when ambient light
levels are low. If the Opti-V is
installed in brightly lit areas, the
strong reections may diminish
the ame.
Depending on your specic ap-
plication, installation of the unit
at a height appropriate for the
viewers enjoyment is important. It
is recommended that the follow-
ing guidelines be used for locating
the unit.
!NOTE: Measurements are to
the bottom of the viewing area of
the ame.
For standing applications:
Maximum - 51 in. (129.5 cm)
Minimum - 26 in. (66.0 cm)
For sitting applications:
Maximum - 36 in. (91.4 cm)
Minimum - 26 in. (66.0 cm)
Hardwire Installation
The Opti-V is supplied in an as-
sembled state and is designed to
be permanently installed. The unit
comes ready for hardwire instal-
lation.
WARNING: Do not attempt
to wire your own new outlets or
circuits. To reduce the risk of re,
electric shock or injury to persons,
always use a licensed electrician.
WARNING: Ensure that the
On/Off switch is set to the Off po-
sition (refer to Operation section)
and that the circuit on which the
Opti-V is to be installed has the
power cut off at the service panel
until installation is complete.
!NOTE: Please read all instruc-
tions before installing.
1. For rough in framing, the
opening should follow the

7
Opti-V Installation
recommended dimensions
located in Figure 1.
!NOTE: Dimensions provided
are minimum clearances and will
vary depending on type of support
framing and nishing options.
!NOTE: Framing should be
constructed to support:
VF2927L / VFA2927 - 63 lbs (29 kg)
VF5452L - 116 lbs (52 kg)
2. Allow up to 4 ft. (121.9 cm) of
service cable for connecting
a power supply wire to the
cable clamp on the Opti-V
when installing before nish-
ing wall.
!NOTE: A 15 amp, 120 volt
alternating current (VAC) circuit
is recommended, but the unit is
constructed that it can operate
using voltages from 120-240VAC.
!NOTE: Use minimum 14 AWG
supply cable with two insulated
copper conductors (white and
black) and one bare ground wire.
C
B
A
E
D
A B C D E F G
VF5452L 54.5 in
(1380 mm)
17.7 in
(450 mm)
13.6 in
(345 mm)
2.9 in
(74 mm)
5.3 in
(135 mm)
18.6 in
(474 mm)
55.3 in
(1404 mm)
VF2927L 30.0 in
(762 mm)
17.7 in
(450 mm)
13.6 in
(345 mm)
2.9 in
(74 mm)
5.3 in
(135 mm)
18.6 in
(474 mm)
30.5 in
(775 mm)
VFA2927 30.0 in
(762 mm)
17.7 in
(450 mm)
13.6 in
(345 mm)
2.9 in
(74 mm)
5.3 in
(135 mm)
18.6 in
(474 mm)
30.5 in
(775 mm)
Figure 1
G
F

8 www.dimplex.com
Opti-V Installation
Do not use cable with alumi-
num conductors.
!NOTE: It is recommended that
all drywall installation and nish-
ing be completed after unit is fully
installed.
3. In the upper left hand corner
of the unit, loosen the two
securing screws and remove
the electrical cover panel.
(Figure 2)
4. Install a ⅜ in. (10 mm) or ½
in. (13 mm) cable connec-
tor, not included, suitable for
mounting in a ⅞ in. (22 mm)
hole, to the cable plate and
feed the supply cable through
the connector and secure.
5. Place the unit in the framed
opening, level with shims if
necessary and attach unit to
frame using mounting anges
provided (Figure 3).
CAUTION: When inserting
the unit take care not to damage
or pinch any of the power cables
that are concealed in the wall.
6. Remove the outer jacket and
strip the individual conductors
½ in. (1.3 cm) from the end.
7. Connect the black wire from
the unit to the Live (120V) or
Line 1 (240V) wire from the
power supply using a wire
connector (included).
8. Connect the white wire from
the unit to the Neutral (120V)
or Line 2 (240V) from the
power supply using a wire
connector (included).
Figure 2
Electrical
Cover Panel
Cable Clamp
Hole
Figure 3
Mounting
Flanges
Cable Plate
Grounding
Screw

9
Opti-V Installation
!NOTE: Cap any additional
wires from the power supply not
used in the installation.
9. Ensure that the green ground-
ing wire is securely attached
to the back plate.
CAUTION: Ensure the
wire connectors are securely
tightened, so no bare wires (live
or neutral) are exposed.
10. Ensure the grounding wire of
the supply cable is securely
attached to the grounding
screw.
!NOTE: The wire connections
on the Opti-V feed into a 3-prong
plug just below the electrical cav-
ity opening, before closing the
electrical cover ensure that the
plug is fully installed.
11. Reinstall the electrical cover
panel.
12. Reinstall the protector sheet
to prevent dust from entering
the unit while nishing the
surround.
13. Finish surrounding wall.
There are 3 different options
for nishing the wall:
• Permanent - install drywall
right up to the ange that sur-
rounds the opening.
• Semi Permanent - nish
around edge using ashing
material (not included)
• Flexible - create opening big
enough to access mounting
anges and a false front that
can be removed.

10 www.dimplex.com
Operation
WARNING: This Opti-V must
be properly installed before it is
used.
The power switch (Figure 2A) must
rst be switched "I" to operate the
appliance.
An ‘Opti-V’ logo will appear on
the screen for about 3 seconds
before the ame picture starts .
!NOTE: The user may notice a
blank screen for approximately 5
seconds, every 30 minutes. This
is normal and should not be a
cause for concern.
Manual Operation
The manual controls for the
screen are located at the inner
top left hand side of the appliance
above the glass.(Figure 2).
The mains (power) switch (Figure
Figure 2
F
IR Remote Sensor
A
2A) may be used to switch the
appliance Off ("O") when it is not
required, for example, overnight
or for long periods, to avoid un-
necessary energy use.
!NOTE: Ensure that the mains
(power) switch shall remain read-
ily operable.
The standby button " " (Figure
2B) is located just below the pow-
er switch. A red light will indicate
when the unit is in standby mode.
(Figure 2)
The volume of the sound effects
may be adjusted up or down by
pressing the volume control but-
tons (Figure 2C & 2D).
The screen brightness can be ad-
justed using the (Figure 2E) and
(Figure 2F) buttons. The but-
ton darkens the screen and the
EB DC