DIODE LED DI-TB-CONN-TT Series User manual

1 OF 2 IG111418-1.0
TAPE LIGHT TERMINAL BLOCK CONNECTOR INSTALLATION GUIDE
®TAPE LIGHT TERMINAL BLOCK CONNECTOR
INSTALLATION GUIDE
SKU DI-TB-CONN-TT*
Max. Voltage 24V
Max. Amp 12V - 5A / 24V - 4A
Wire Gauge 16 AWG - 20 AWG
Ambient Temp
†-4° - 122°F (-20° - 50°C)
1.Install in accordance with national and local electrical
code regulations.
2.This product is intended to be installed and serviced by a
qualied, licensed electrician.
3.Do not modify or disassemble this product beyond
instructions or the warranty will be void.
4.Do not submerge, or install within 5 feet of a swimming
pool.
5.Failure to follow safety warnings, and installation
instructions will void the warranty for this product.
SAFETY & WARNINGS
QUICK SPECS / MODELS
† Do not install product in environment outside listed
temperature.
DO NOT CONNECT
TO HIGH VOLTAGE
INSTALLATION (WIRE)
Tape-to-Tape Tape-to-Wire
1
INSERT WIRE
Insert 16-20 AWG wire into terminals, observing polarity.
+
+
-
-
SECURE CONNECTION
Using phillips head screwdriver, fasten terminal screws
to secure wire in place.
2
Front
Back
Front
Back
DRY LOCATION

2 OF 2
®Toll Free: 877.817.6028 | Fax: [phone] | www.DiodeLED.com | [e-mail]
© 2018 Elemental LED Inc. All rights reserved. Specicaons are subject to change without noce.
IG111418-1.0
TAPE LIGHT TERMINAL BLOCK CONNECTOR INSTALLATION GUIDE
TAPE LIGHT TERMINAL BLOCK CONNECTOR
INSTALLATION GUIDE
INSTALLATION (STRIP)
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
+
-
+
-
+
-
+
--
+
-
+
-
+
-
+
-
+
Refer to chart below for number of solder pads recommended to leave on end of Tape Light when connecting
to Screw Clip Connector.
2 Solder pads
+
-
+
-
+
-
+
-
+
1
CUT TAPE LIGHT (2 SOLDER PAD)
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
INSERT TAPE LIGHT
2
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
+
-
+
-
+
-
+
--
+
-
+
-
+
-
+
-
+
4 Solder pads
1
CUT TAPE LIGHT (4 SOLDER PAD)
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
INSERT TAPE LIGHT
2
Cut Tape Light just before two extra required solder
pads.
3
SECURE CONNECTION
Using phillips head screwdriver, fasten terminal screws
to secure Tape Light in place.
+
-
+
-
Insert Tape Light into terminal, observing polarity.
Insert Tape Light into terminal, observing polarity.
BLAZE™BASICS 100 BLAZE™BASICS 200 BLAZE™X 100 BLAZE™X 200 BLAZE™X 300
2 SOLDER PADS  
4 SOLDER PADS   
-
+
-
+
-
+
-
+
-
+
-
+
--
+
-
+
-
+
-
+
-
+
2 Solder pads
4 Solder pads
INSTALLATION (2 SOLDER PAD)
INSTALLATION (4 SOLDER PAD)