DIODE LED VOLANTE LED Canopy Light User manual

1 OF 5 IG112918-3.0
VOLANTE
™
LED Canopy Light INSTALLATION GUIDE
®VOLANTE® LED Canopy Light
INSTALLATION GUIDE
Input 120V-277VAC
Power 100w or 200w
Ambient
Temp
†-4° - 113°F (-20° - 45°C)
QUICK SPECS / MODELS
† Do not install product in environment outside
listed temperature.
DRY/WET LOCATION
120V-
277V
AC
IP65
SAFETY & WARNINGS
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. Install in accordance with national and local electrical code
regulations.
3. This product is intended to be installed and serviced by a
qualied, licensed electrician.
4. Do not use if there is any damage to xture or wiring. Inspect
periodically.
5. Do not submerge xture in liquids or use the product in the
vicinity of standing water or other liquids.
6. Do not install near areas with exposure to salt water or
chlorinated water.
7. Do not install in direct sunlight or damage to the LED
phosphor will occur.
8. Do not attempt to x this product in the eld.
9. Failure to follow safety warnings, and installation instructions
will be void the warranty for this product.
Recessed Canopy
Surface Mount Canopy

2 OF 5 IG112918-3.0
VOLANTE
™
LED Canopy Light INSTALLATION GUIDE
VOLANTE® LED Canopy Light
INSTALLATION GUIDE
INSTALLATION
TURN POWER OFF AT CIRCUIT
BREAKER
SHOCK HAZARD! May result in serious
injury or death.
Turn power OFF at circuit breaker prior to
installation.
DETERMINE LOCATION TO INSTALL
COMPONENTS
*NOT FOR USE IN SUBMERSIBLE APPLICATIONS, OR
WITHIN 5 FEET OF A SWIMMING POOL.
REQUIRED TOOLS
1
2
3
1. Phillips-head Screwdriver and/or Power Drill
2. Ruler
3. (4x) Appropriate Mounting Screws Wood/Concrete etc.
4. Junction Box
5. (3x) Twist-On Wire Connectors
6. Wire Strippers
5.9”
16”
MOUNTING BRACKET MEASUREMENTS
4
5
6
1
2
Recessed Canopy measurements*
15.75”
15.75”
*Note: Above listed measurements are the same
for 2 module, and 3 module xtures.

3 OF 5 IG112918-3.0
VOLANTE
™
LED Canopy Light INSTALLATION GUIDE
VOLANTE® LED Canopy Light
INSTALLATION GUIDE
INSTALLATION (CONT.)
5.51”
4.52”
Surface Mount Canopy measurements*
15.75”
13.89”
3
ATTACH MOUNTING BRACKETS
Use included screws to attach mounting brackets
to VOLANTE®LED Recessed Canopy Light.
Use included screws to attach mounting brackets
to VOLANTE®LED Surface Mount Canopy Light.
a
b
RECESSED CANOPY
SURFACE MOUNT CANOPY
4
MOUNT CANOPY
a
RECESSED CANOPY
Use appropriate mounting screws (not included)
to mount canopy to studs, or support braces.
a.1
*Note: Above listed measurements are the same
for 2 module, and 3 module xtures.

4 OF 5 IG112918-3.0
VOLANTE
™
LED Canopy Light INSTALLATION GUIDE
VOLANTE® LED Canopy Light
INSTALLATION GUIDE
INSTALLATION (CONT.)
SURFACE MOUNT CANOPY
Use appropriate mounting screws (not included)
to attach VOLANTE® Canopy xture to surface.
Ensure mounting screws are secured through to
studs, or support braces.
b.1
b.2
b
Place canopy within 15.75” x 15.75” opening.
15.75” x 15.75”
a.2
Use included screws to attach cover to xture.

5 OF 5
®Toll Free: 877.817.6028 | Fax: [phone] | www.DiodeLED.com | [e-mail]
© 2018 Elemental LED Inc. All rights reserved. Specicaons are subject to change without noce.
IG112918-3.0
VOLANTE
™
LED Canopy Light INSTALLATION GUIDE
VOLANTE® LED Canopy Light
INSTALLATION GUIDE
CONNECT WIRING
Lights are
ickering
• This product is not dimmable. Only install on
switching (On/O circuit).
• Verify xture is wired to a 120V-277VAC circuit.
Lights
will not
illuminate
• Ensure main power is turned On.
• Ensure breaker has not tripped.
TROUBLESHOOTING
TOOLS & RESOURCES
VOLANTE® LED CANOPY LIGHT
SPECIFICATION SHEET
For full specicaons.
TURN POWER ON AT CIRCUIT BREAKER
GROUND (GREEN)
HOT (BLACK)
NEUTRAL (WHITE)
GROUND (GREEN)
HOT (BLACK)
NEUTRAL (WHITE)
Connect wiring to 120V-277V AC circuit within an
appropriately rated junction box.
If installing outdoors, ensure junction box is rated for
outdoor use, and sealed properly before continuing.
INSTALLING OUTDOORS?
5
6
INSTALLATION (CONT.)