Directed VW10 User manual

VW10
INSTALLATION GUIDE
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
2017-06-22
© 2017 Directed, Vista CA
Directed Digital
Solutions
Designed by Installers for Installers

Contents
Warning! Safety first ....................................................................................................................... 3
Introduction .................................................................................................................................... 4
Pre-installation and application warnings ..................................................................................... 4
Vehicle application guide........................................................................................................... 5
Wiring connections ......................................................................................................................... 6
Main power harness (H1), 12-pin thick gauge connector ............................................................... 6
Auxiliary output harness (H2), 16-pin black connector ................................................................... 6
Analog harness (H3), 18-pin white connector ............................................................................... 7
MC501 harness (H4), 8 thick-gauge wires (optional)..................................................................... 7
Installation (wiring diagrams & vehicle wiring reference charts) ............................................................ 8
Type 1 ..................................................................................................................................... 8
Type 2 ................................................................................................................................... 10
Type 3 ................................................................................................................................... 13
Type 4 ................................................................................................................................... 15
Type 5 ................................................................................................................................... 17
Type 6 ................................................................................................................................... 19
Type 7 ................................................................................................................................... 21
Type 8 ................................................................................................................................... 23
Type 9 ................................................................................................................................... 25
Type 10 ................................................................................................................................. 28
Type 11 ................................................................................................................................. 30
Type 12 ................................................................................................................................. 32
Immobilizer interface .................................................................................................................... 34
Method 1: Key Wrap .............................................................................................................. 34
Method 2: Immobilizer interface with 556U (Regular Key) ........................................................... 34
Method 3: Immobilizer interface with OEM Immobilizer Receiver .................................................. 35
Connecting the module .................................................................................................................. 36
Important! .............................................................................................................................. 36
Manual or automatic transmission selection ................................................................................ 36
Optional sensors ..................................................................................................................... 37
RF Systems ............................................................................................................................. 37
When used in conjunction with SmartStart.................................................................................. 37
Module programming.............................................................................................................. 38
LED diagnostics and troubleshooting.......................................................................................... 39
Soft reset................................................................................................................................ 41
Hard reset .............................................................................................................................. 41
Learning the Tach (not needed with Virtual Tach) ............................................................................... 42
Initializing Virtual Tach (not needed with hardwired or data tach applications) ..................................... 42
Limited lifetime consumer warranty .................................................................................................. 43
Quick Reference Guide.................................................................................................................. 44

3Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Warning! Safety first
The following safety warnings must be observed at all times:
• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.
• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never
operate the system in an area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
• Never use a test light or logic probe when installing this unit. Always use a multimeter.
• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
• When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must
be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from
children all remote controls to assure that the system does not unintentionally remote start the vehicle.
• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE
STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or
death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with
the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the
neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product
installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem
immediately.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF
OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE
OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE
START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the
installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged
parking brake. Do not allow anyone to stand in front of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such
vehicles may pose certain risk.

4Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Introduction
The VW10 firmware for Directed Digital Solutions is compatible with specific [Volkswagen] and [Audi] vehicles.
It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide
provides information on the installation of the module using VW10. If you would prefer using this system as a
digital solution, go to www.directechs.com and search for the make, model and year of the vehicle. This will
allow you to find the proper firmware and corresponding installation guide.
Warning! This module can only be programmed via the web tool, which can be found on www.directechs.com or using the
Directechs Mobile application for mobile devices. Features and functions will become accessible when you connect the module
using the XKLoader.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Keys required for
programming 1Keys required for operation 1
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
connector.
Refer to the "Vehicle wiring reference chart" following each installation type.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] For Key Wrap instructions, refer to pages 34 & 35.
[4] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.
[5] Diodes and brake connection only required on vehicles where brake needs to be depressed to start.
Additional parts required (maximum required):
Diode 6A
2 x 1A Diodes 86 85
30
87a
87
2 x Relay
Resistor 100Ω
0 x Resistor
Fuse 7.5A
2 x Fuse

5Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Vehicle application guide
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year
allows you to determine which installation type should be used for your vehicle.
Vehicles
2017 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 PK-Universal RF Bypass- Key Req'd AV-Parking Lights Control DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote RS-3x LOCK START (Start control using OEM Remote) RS-3x LOCK STOP (Stop control using OEM Remote) RS-Accessory Activation RS-Ignition Activation RS-RAP Shut Down (Retained ACC Power) RS-SmartStart RS-Start (Crank) Activation RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-Door Locks Status ST-E-Brake Status ST-Ignition Status
Audi 17 16 15 14 13 12 11 10 09 08 07 06 05 04
A3 4 4 4 4 4 or 8 88888••••••••••••••••••••••••
Q3 555 ••••••••••••••••••••••••
R8 4 4 4 4 4 8 8 ••••••••••••••••••••••••
TT 4 4 4 4 4 4 8 888 ••••••••••••••••••••••••
Volkswagen 17 16 15 14 13 12 11 10 09 08 07 06 05 04
EOS 1 1 1 1 1 9 999 ••••••••••••••••••••••••
Golf 22222 or 7 9 999 ••••••••••••••••••••••••
GTI 22222 or 7 9 999 ••••••••••••••••••••••••
Jetta 11 11 3 or 12 3 or 12 3 or 12 3 or 12 3 or 9 9 999 ••••••••••••••••••••••••
Passat 2 2 2 2 2 2 10 10 10 10 10 10 ••••••••••••••••••••••••
Passat CC 6666610 10 10 ••••••••••••••••••••••••
Rabbit 9 999 ••••••••••••••••••••••••
Tiguan 11 1 1 1 1 1 ••••••••••••••••••••••••
Legend:
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Remote
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status

6Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Wiring connections
The wiring connections listed below are specific to this firmware.
Main power harness (H1), 12-pin thick gauge connector
Conn./Pin Color Description
H1/1 White Relay 3 COM – (+) Accessory Output 1
H1/2 White/Brown Relay 3 N.O. – (+) Accessory Input 1
H1/3 Brown/Red Relay 2 N.O.– Key Wrap
H1/4 Yellow/Red Relay 2 COM – Key Wrap
H1/5 Orange/Red Relay 2 N.C. – Key Wrap
H1/6 Yellow
Relay 1 COM – Parking Light Interrupt (vehicle side) or (+) Parking Light Output
1
H1/7 White Relay 3 COM – Accessory Output 1
H1/8 White/Brown Relay 3 N.O. – (+) Accessory Input 1
H1/9 Black (-) Ground
H1/10 Red (+) 12 Volt (Battery)
H1/11 Orange/Yellow Relay 1 N.C. – Parking Light Interrupt (conn.side) 1
H1/12 Brown Relay 1 N.O. – (+) Parking Light Output or (+) Parking Light Input 1
Auxiliary output harness (H2), 16-pin black connector
Conn./Pin Color Description
H2/1 Violet/Brown (MUX) Lock/Unlock Output
H2/2 Yellow/Black No Connection
H2/3 Orange/Black No Connection
H2/4 Tan HS CAN Low
H2/5 Tan/Black HS CAN High
H2/6 Light Green No Connection
H2/7 Orange/Green FT CAN High
H2/8 Orange/Brown FT CAN Low
H2/9 Violet/Green No Connection
H2/10 Green/Black (-) Hazards Output 2
H2/11 White/Violet No Connection 2
H2/12 White/Red (+) Starter/Brake Activation Output 2
H2/13 Lt. Blue/Black No Connection 2
H2/14 Green/Red (+) Ignition Output 2
H2/15 N/A No Connection
H2/16 Violet/Yellow No Connection
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.
2. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay
may be necessary.

7Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Analog harness (H3), 18-pin white connector
Conn./Pin Color Description
H3/1 Lt. Blue/Red No Connection
H3/2 Black/White (-) Parking Brake Input (Manual Transmission) 2
H3/3 Gray (-) Hood Input 2
H3/4 N/A No Connection
H3/5 Gray/Black (+) Glow Plug Input 2
H3/6 Violet/White (AC) Tach Input 2
H3/7 Dark Blue No Connection 1
H3/8 Brown/Black (-) Horn 1
H3/9 Red/White (-) Trunk Release Output 1
H3/10 White/Green (-) Door Input 2
H3/11 Yellow/Green (+) Door Input 2
H3/12 Blue/Red No Connection
H3/13 Light Blue (-) Trunk Trigger Input 2
H3/14 Pink/Yellow (-) Activation (Start Trigger) Input
H3/15 Dark Green No Connection 1
H3/16 Brown/White (+) Brake Input 2
H3/17 Brown (+) Siren Output 1
H3/18 Blue/White (-) Key Release Output 1
MC501 harness (H4), 8 thick-gauge wires (optional)
Conn./Pin Color Description
H4/1 Pink/White No Connection
H4/2 Red/White No Connection
H4/3 Pink No Connection
H4/4 Red No Connection
H4/5 Orange No Connection
H4/6 Red No Connection
H4/7 Green No Connection
H4/8 Violet No Connection
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay
may be necessary.
2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a
list of compatible features.

8Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Installation (wiring diagrams & vehicle wiring reference charts)
Type 1
Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 9 for important information on this installation.
Siren
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
6
14
18
916
12
29
28
42 25 1
52 41 24 11
FT CAN Low: Orange/Brown, pin 3
(+) Ignition:
Black, pin 14
(+) Starter: Red/Black or
Red/Brown,pin 6
FT CAN High: Orange/Green, pin 4
Brown VESCM connector C
(+) Brake: Black/Red, pin 17
(+) 12V:
Red/Yellow,
pin 42
Hood Pin
11: Orange/Yellow: Parking Light Interrupt (conn. side)
12: Brown: (+) Parking Light Output
6: Yellow: Parking Light Interrupt (vehicle side)
4: Yellow/Red: Key Wrap
3: Brown/Red: Key Wrap
5: Orange/Red: Key Wrap
9: Black: (-) Ground
10: Red: (+) 12V Input
1
2
4
5
6
7
9
10
3
8
Headlight switch
(black conn. at
light switch)
Steering column module
(behind steering column
trim)
CUT
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(+) Starter / Brake Activation Output: White/Red: 12
(+) Ignition Output: Green/Red: 14
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
16
8
9
1Diagnostic
Connector OBDII
[5] Diode 1A
[5] Diode 1A
B
CA
VESCM-Driver side underdashboard
Parking Lights Interrupt: Red/White or Red/Blue, pin 8
(+) Parking Lights: Gray/Yellow, pin 3

9Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen EOS 2010-2014
Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A
Ignition Black 14 (+) Steering column module. Black 16 B
Starter Red/Brown or Red/Black 6 (+) Steering column module. Black 16 B
FT CAN High Orange/Green 4 Data Steering column module. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
Volkswagen Tiguan 2012-2016
Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 A
Parking Light Interrupt Red/Blue 8 Cut Headlight switch. Black 10 A
Ignition Black 14 (+) Steering column module behind steering column trim. Black 16 B
Starter Red/White or Red/Black 6 (+) Steering column module behind steering column trim. Black 16 B
FT CAN High Orange/Green 4 Data Steering column module behind steering column trim. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module behind steering column trim. Black 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/Violet 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D

10 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Type 2
Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 11 for important information on this installation.
Siren
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
6
14
18
916
12
29
28
42 25 1
52 41 24 11
FT CAN Low: Orange/Brown, pin 3
(+) Ignition:
Black, pin 14
(+) Starter: Red/Black or
Red/Brown,pin 6
FT CAN High: Orange/Green, pin 4
Brown VESCM connector C
(+) Brake: Black/Red, pin 17
(+) 12V:
Red/White or
Red/Yellow,
pin 42
Hood Pin
11: Orange/Yellow: Parking Light Interupt (conn. side)
12: Brown: (+) Parking Light Output
6: Yellow: Parking Light Interrupt (vehicle side)
4: Yellow/Red: Key Wrap
3: Brown/Red: Key Wrap
5: Orange/Red: Key Wrap
9: Black: (-) Ground
10: Red: (+) 12V Input
Parking Lights Interrupt: Red/White, pin 8
(+) Parking Lights: White/Black, pin 1
1
2
4
5
6
7
9
10
3
8
Headlight switch
(black conn. at
light switch)
Steering column module
(behind steering column
trim)
CUT
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(+) Starter / Brake Activation Output: White/Red: 12
(+) Ignition Output: Green/Red: 14
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
16
8
9
1Diagnostic
Connector OBDII
Diode 1A
[5] Diode 1A
B
CA
VESCM-Driver side underdashboard

11 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen Golf 2010
Parking Light White/Black 1 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A
Ignition Black 14 (+) Steering column module. White 16 B
Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B
FT CAN High Orange/Green 4 Data Steering column module. White 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. White 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/White or Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
Volkswagen GTI 2010
Parking Light White/Black 1 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A
Ignition Black 14 (+) Steering column module. White 16 B
Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B
FT CAN High Orange/Green 4 Data Steering column module. White 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. White 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/White or Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D

12 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen Golf 2011-2014
Parking Light White/Black 1 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White or Red/Yellow 8 Cut Headlight Switch. Black 10 A
Ignition Black 14 (+) Steering column module. White 16 B
Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B
FT CAN High Orange/Green 4 Data Steering column module. White 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. White 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/White or Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
Volkswagen GTI 2011-2014
Parking Light White/Black 1 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A
Ignition Black 14 (+) Steering column module. White 16 B
Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B
FT CAN High Orange/Green 4 Data Steering column module. White 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. White 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/White or Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
Volkswagen Passat 2012-2017
Parking Light White/Black 1 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White or Red/Yellow 8 Cut Headlight Switch. Black 10 A
Ignition Black 14 (+) Steering column module. Black 16 B
Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B
FT CAN High Orange/Green 4 Data Steering column module. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/White or Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D

13 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Type 3
Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 14 for important information on this installation.
11: Orange/Yellow: Parking Light Interupt (conn. side)
12: Brown: (+) Parking Light Output
2 & 8: White/Brown: (+) 12V Input
6: Yellow: Parking Light Interrupt (vehicle side)
4: Yellow/Red: Key Wrap
3: Brown/Red: Key Wrap
5: Orange/Red: Key Wrap
9: Black: (-) Ground
10: Red: (+) 12V Input
1 & 7: White: (+) Accessory Output
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(+) Starter / Brake Activation Output: White/Red: 12
(+) Ignition Output: Green/Red: 14
(MUX) Lock/Unlock Output: Violet/Brown: 1
Siren
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
Hood Pin
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
[5] Diode 1A
(+) Ignition:
Black/Violet, pin 8
(+) Starter:
Red/Black,
pin 4 (+) Accessory:
Black/Red, pin 3
1
2
4
5
6
7
9
10
3
8
FT CAN High:
Orange/Green, pin 20
FT CAN Low:
Orange/Brown, pin 21
16
8
9
1Diagnostic
Connector OBDII
(-) Trunk
Release:
Violet, pin 23
(MUX) Doorlock:
Blue/Red,pin 24
(+) 12V:
Red/White or
Red/Yellow, pin 68
(+) Brake:
Black/Red, pin 39
Ignition Switch
(black conn. at ignition switch)
(-) Trunk Release Output: Red/White: 9
[5] Diode 1A
37
63
73
17
16
1
73
16
37
6317
1
Connector
B
Connector
A
VESCM - (under drivers kick)
White VESCM Connector B
(under drivers kick)
Black VESCM connector A
(under drivers kick)
Parking Lights Interrupt : Gray/Red or
Red/White, pin 8
1
2
4
5
6
7
9
10
3
8
CUT
Headlight Switch
(black conn. at
light switch)
(+) Parking Lights:
White/Black, pin 1

14 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen Jetta 2010
Ignition Black/Violet 8 (+) Ignition switch. Black 10 A
Starter Red/Black 4 (+) Ignition switch. Black 10 A
Accessory Black/Red 3 (+) Ignition switch. Black 10 A
Parking Light White/Black 1 (+) Headlight switch. Black 10 B
Parking Light Interrupt Red/White 8 Cut Headlight switch. Black 10 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
FT CAN High Orange/Green 20 Data VESCM connector B, under drivers dash. White 73 D
FT CAN Low Orange/Brown 21 Data VESCM connector B, under drivers dash. White 73 D
12V Red/White or Red/Yellow 68 (+) VESCM connector A, under drivers dash. Black 73 E
Brake Black/Red 39 (+) VESCM connector A, under drivers dash. Black 73 E
Doorlocks [4] Blue/Red 24 MUX VESCM connector A, under drivers dash. Black 73 E
Trunk Release [4] Violet 23 (-) VESCM connector A, under drivers dash. Black 73 E
Volkswagen Jetta 2011-2014 with Autolights
Ignition Black/Violet 8 (+) Ignition switch. Black 10 A
Starter Red/Black 4 (+) Ignition switch. Black 10 A
Accessory Black/Red 3 (+) Ignition switch. Black 10 A
Parking Light White/Black 1 (+) Headlight switch. Black 10 B
Parking Light Interrupt Gray/Red 8 Cut Headlight switch. Black 10 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
FT CAN High Orange/Green 20 Data VESCM connector B, under drivers dash. White 73 D
FT CAN Low Orange/Brown 21 Data VESCM connector B, under drivers dash. White 73 D
12V Red/White or Red/Yellow 68 (+) VESCM connector A, under drivers dash. Black 73 E
Brake Black/Red 39 (+) VESCM connector A, under drivers dash. Black 73 E
Doorlocks [4] Blue/Red 24 MUX VESCM connector A, under drivers dash. Black 73 E
Trunk Release [4] Violet 23 (-) VESCM connector A, under drivers dash. Black 73 E

15 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Type 4
Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 16 for important information on this installation.
Siren
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
Steering Column Control Unit
12
29
28
42 25 1
52 41 24 11
FT CAN Low: Orange/Brown, pin 15
(+) Ignition: Pin 17
FT CAN High: Orange/Green, pin 14
Brown VESCM connector C
(-) Hazards: Brown/Red, pin 7
(+) Brake: Black/Red, pin 17
(+)12V: Red/Blue or
Red/Violet, pin 42
Hood Pin
4: Yellow/Red: Key Wrap
3: Brown/Red: Key Wrap
5: Orange/Red: Key Wrap
9: Black: (-) Ground
10: Red: (+) 12V Input
Steering Column Module
(behind steering column trim)
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(-) Hazards Output: Green/Black: 10
(+) Starter / Brake Activation Output: White/Red: 12
(+) Ignition Output: Green/Red: 14
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
16
8
9
1Diagnostic
Connector OBDII
17
10
1
20
[5] Diode 1A
[5] Diode 1A
B
CA
VESCM-Driver side underdashboard
(+) Starter: Red/Black
or Black/Gray,pin 18

16 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Audi A3 2010-2013
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A
Ignition Black/Green 17 (+) Steering column module behind steering column trim. Black 20 B
Starter Red/Black 18 (+) Steering column module behind steering column trim. Black 20 B
FT CAN High Orange/Green 14 Data Steering column module behind steering column trim. Black 20 B
FT CAN Low Orange/Brown 15 Data Steering column module behind steering column trim. Black 20 B
12V Red/Blue 42 (+) VESCM, connector C, under drivers dash. Brown 52 C
Brake Black/Yellow 17 (+) VESCM, connector C, under drivers dash. Brown 52 C
Hazards Gray/Yellow 19 (-) VESCM, connector A, under drivers dash. Black 52 C
Audi R8 2012-2014
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A
Ignition Black/Violet 17 (+) Steering column module behind steering column trim. Black 20 B
Starter Black/Gray 18 (+) Steering column module behind steering column trim. Black 20 B
FT CAN High Orange/Green 14 Data Steering column module behind steering column trim. Black 20 B
FT CAN Low Orange/Brown 15 Data Steering column module behind steering column trim. Black 20 B
12V Red/Violet 42 (+) VESCM, connector C, under drivers dash. Brown 52 C
Brake Black/Red 17 (+) VESCM, connector C, under drivers dash. Brown 52 C
Hazards Black/White 19 (-) VESCM, connector A, under drivers dash. Black 52 C
Audi TT 2012-2015
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A
Ignition Black/White 17 (+) Steering column module behind steering column trim. Black 20 B
Starter Red/Black 18 (+) Steering column module behind steering column trim. Black 20 B
FT CAN High Orange/Green 14 Data Steering column module behind steering column trim. Black 20 B
FT CAN Low Orange/Brown 15 Data Steering column module behind steering column trim. Black 20 B
12V Red/Violet 42 (+) VESCM, connector C, under drivers dash. Brown 52 C
Brake Black/Yellow 17 (+) VESCM, connector C, under drivers dash. Brown 52 C
Hazards Gray/Yellow 19 (-) VESCM, connector A, under drivers dash. Black 52 C

17 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Type 5
Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 18 for important information on this installation.
Siren
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
6
14
18
916
12
29
28
42 25 1
52 41 24 11
FT CAN Low: Orange/Brown, pin 3
(+) Ignition:
Green/Black, pin 14
(+) Starter: Red/Black,pin 6
(+) Brake: Black/Red, pin 17
(-) Hazards: Brown/Red, pin 7
(+) 12V:
Red/Yellow,
pin 42
Hood Pin
4: Yellow/Red: Key Wrap
3: Brown/Red: Key Wrap
5: Orange/Red: Key Wrap
9: Black: (-) Ground
10: Red: (+) 12V Input
Steering Column Module
(behind steering column trim)
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(-) Hazards Output: Green/Black: 10
(+) Starter / Brake Activation Output: White/Red: 12
(+) Ignition Output: Green/Red: 14
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
16
8
9
1Diagnostic
Connector OBDII
[5] Diode 1A
[5] Diode 1A
FT CAN High: Orange/Green
or Lt.Green, pin 4
B
CA
VESCM-Driver side underdashboard
Brown VESCM connector C

18 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Audi Q3 2015-2017
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A
Ignition Green/Black 14 (+) Steering column module behind steering column trim. Black 16 B
Starter Red/Black 6 (+) Steering column module behind steering column trim. Black 16 B
FT CAN High Orange/Green or
Lt.Green 4 Data Steering column module behind steering column trim. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module behind steering column trim. Black 16 B
12V Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 C
Hazards Brown/Red 7 (-) VESCM connector C, under drivers dash. Brown 52 C
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 C

19 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Type 6
Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 20 for important information on this installation.
Siren
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
6
18
916
12
29
28
42 25 1
52 41 24 11
FT CAN Low:
Orange/Brown, pin 16
(+) Ignition:
Red/Green or
Violet/Yellow, pin 5
(+) Keysense:
Green or
Green/Blue, pin 16
FT CAN High:
Orange/Green, pin 15
Brown VESCM connector C
[5] (+) Brake: Black/Red, pin 17
(+) 12V:
Red/Yellow,
pin 42
Hood Pin
11: Orange/Yellow: Parking Light Interupt (conn. side)
12: Brown: (+) Parking Light Output
6: Yellow: Parking Light Interrupt (vehicle side)
4: Yellow/Red: Key Wrap
3: Brown/Red: Key Wrap
5: Orange/Red: Key Wrap
9: Black: (-) Ground
10: Red: (+) 12V Input
Parking Lights Interrupt: Red/White or Red/Black, pin 8
(+) Parking Lights: Gray/Yellow or Gray/Green, pin 3
1
2
4
5
6
7
9
10
3
8
Headlight switch
(black conn. at light switch)
Ignition Switch Port
(black conn. at keyport)
CUT
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(+) Starter / Brake Activation Output: White/Red: 12
(+) Ignition Output: Green/Red: 14
(-) Key Release Output: Brown/White: 16
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
16
8
9
1
Diagnostic
Connector OBDII
Ignition Switch Plug
(at Key Port)
30
86 85 87
87a
Fuse 5A
[5] Diode 1A
[5] Diode 1A
B
CA
VESCM-Driver side underdashboard
(+) Starter: Pin 6

20 Directed Digital Solutions VW10
© 2017-06-22 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen Passat CC 2011-2015
Parking light Gray/Yellow or Gray/
Green 3 (+) Headlight switch. Black 10 A
Parking light Interrupt Red/White or Red/Black 8 Cut Headlight switch. Black 10 A
Ignition Red/Green or Violet/
Yellow 5 (+) Ignition switch port. Black 16 B
Starter Red/Brown or Red/Gray
or Red/Yellow 6 (+) Ignition switch port. Black 16 B
Keysense Green or Green/Blue 16 (+) Ignition switch port. Black 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
FT CAN High Orange/Green 15 Data VESCM connector C, under drivers dash. Brown 52 D
FT CAN Low Orange/Brown 16 Data VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D