Dish Network 135331 User manual

WARNING AND ATTENTION SYMBOLS
You must be aware of safety when you install and use this system. This User Guide
provides various procedures. If you do some of these procedures carelessly, you could
injure or kill yourself or damage equipment or property. Some other procedures require
special attention.
FOR YOUR SAFETY
The WARNING! symbol means that if you are not careful:
You could injure or kill yourself, or
You could damage equipment or property.
The ATTENTION! symbol means you should pay special
attention to:
Important instructions for using the system, or
Important instructions for maintaining the system.
The Class II Symbol alerts qualified service personnel to use
only identical replacement parts in this apparatus.
Do not try to open the case of the receiver. There is risk of
electrical shock, which may cause damage to the receiver
and/or personal injury or death to you. There are no user-
serviceable parts inside the receiver. Opening the receiver
case or making unauthorized changes will void the warranty.
To reduce the risk of fire or electric shock, do not expose this
appliance to rain or moisture.
inside_front_cover.fm Page 1 Friday, February 11, 2005 4:17 PM

1
TABLE OF CONTENTS
Safety Instructions.............................................. 2
Introduction ......................................................... 3
Setting Up the Kit ................................................ 5
Setting Up the Signal Converter..........................5
Setting Up the Remote Control...........................9
Remote Control Operation ............................... 10
Changing the Receiver and Remote
Control Addresses............................................. 10
Checking the Remote Control Address..............11
Setting Up to Control Other Devices..................11
Operating Modes............................................... 17
Controlling the Satellite Receiver...................... 17
Controlling a TV (or a Second TV)....................25
Controlling a VCR (or a Second VCR
or a DVD Player)...............................................27
Controlling a Tuner or Amplifier.........................29
Changing Frequencies...................................... 31
Device Codes..................................................... 33
Troubleshooting the Kit.................................... 42
Limited Warranty............................................... 45
Advance Exchange Program ............................ 46
Post Receipt Exchange Program...................... 46
If You Need Help............................................... 47
Regulatory Factors............................................ 48
Pyramid.book Page 1 Wednesday, February 16, 2005 4:00 PM

2
SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet, consult an electri-
cian for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, con-
venience receptacles, and the point where they exit from the apparatus.
11. Use only attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods of
time.
13. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as the power supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the appara-
tus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
Apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on the apparatus.
INSTALLATION
Observe Warnings: Carefully follow all warnings on the device and in the operating
instructions.
Heat: DO NOT place the device near heat sources such as radiators, stoves, heat registers,
or other appliances that produce heat.
CARE AND USE
Cleaning: DO NOT use liquid, abrasive, solvent, or aerosol cleaners. Use a damp cloth for
cleaning.
When Not in Use: Remove the batteries if this device is to be left unattended or unused for a
long period of time.
Refer servicing to qualified personnel when a solid object
or liquid has fallen onto or into the device.
DO NOT attempt to service this device. Refer all
servicing to qualified personnel. Opening covers other
than the battery cover will void the warranty.
Pyramid.book Page 2 Wednesday, February 16, 2005 4:00 PM

3
INTRODUCTION
The IR-to-UHF Pro Upgrade Kit lets you use an ultra-high frequency
(UHF) remote to control an infrared (IR) DISH Network satellite TV
receiver from much farther away than with an IR remote control, even
through walls that block IR signals.
Note: The remote control/converter combination included in this kit
works only with compatible DIS H Network receivers, and is not for
any other devices. Compatible DISH Network receivers include all
models except Model 7100/7200 (DISHPlayer), Model HM-
DSR100RU (JVC-DVHS), Model 2000, Model 4000, and Model
5000. The UHF Pro remote can control other devices (a TV, for
example) at short distances because it sends IR signals to such devices.
After you set up the kit, when you press any button on the UHF Pro
remote control, the remote control sends a UHF signal to the converter.
Figure 1. UHF Pro Remote Control sends signals to the Converter
Because the UHF signal can go through walls and other objects on its
way to the converter, you can use the UHF Pro remote control in any
room.
Figure 2. UHF Pro signals go through walls and other objects
Pyramid.book Page 3 Wednesday, February 16, 2005 4:00 PM

4
The converter gets the UHF signal, changes it to IR, and sends the IR
signal to the receiver. The best way to get the IR signal to the receiver
is with the IR extender cable because the signal doesn’t have to go
through the air, but you can also use just the converter to send the
signal to the receiver (see the example in Figure 3).
Figure 3. The Converter changes the UHF Pro
signals to IR to control the receiver
The remote control that comes with the kit gives you easy access to all
the features of a DISH Network satellite TV receiver. You can set up
the remote to control the satellite TV receiver and up to three other
devices. These devices can be a TV, a VCR or DVD player, and a third
device. To control these devices, they must be in the same room as the
remote control.
Note: This remote control may have more features than what your
satellite receiver supports. See your receiver user’s guide for
information.
The remote control included with this kit uses only UHF radio signals
to control the satellite receiver but uses IR to control other devices.
•UHF signals usually travel long distances (200 feet in open air)
and can go through walls and other solid objects. You don’t have
to point a UHF Pro remote control toward the receiver, because
UHF signals spread out in all directions.
•IR signals usually travel only short distances (40 feet or less), and
can’t go through walls or other solid objects. You must point an IR
remote control toward the device, because IR signals travel in
straight lines. There can’t be any objects that block the signal path.
Pyramid.book Page 4 Wednesday, February 16, 2005 4:00 PM

5
SETTING UPTHE KIT
The kit includes a UHF Pro remote control, batteries, an IR extender
cable, an IR clip, an AC adapter, a converter, and a UHF antenna.
Figure 4. Parts of the IR-to-UHF Pro Upgrade Kit
SETTING UPTHE SIGNAL CONVERTER
1. Make sure you fully install the satellite TV system. See the satellite
receiver’s User Guide.
2. Select a location for the converter that has access to a 110 V power
outlet and is close enough for the IR extender cable to reach the
satellite receiver.
3. Refer to Figure 5 to complete steps a through d.
Figure 5. Converter Back Panel
a. Attach the antenna to the REMOTE ANTENNA
on the back of the converter. You may need to
move the antenna around to find where it
works best.
Pyramid.book Page 5 Wednesday, February 16, 2005 4:00 PM

6
Tighten the connection only by hand. If you use a
wrench, you may over-tighten the connection and
damage your equipment. Such damage is not covered
by the Limited Warranty.
b. Make sure the REMOTE KEY switch matches the UHF Pro
key at the bottom of the remote. If the switch setting does not
match the key or if you'd like to change these settings, see
Changing Frequencies on page 31.
c. Plug in the IR extender cable to the IR EXTENDER
connection on the back of the converter.
d. Plug in the AC adapter to the POWER connection
on the back of the converter.
4. Refer to Figures 6 and 7 to place the IR extender’s IR head directly
in front of the receiver’s front panel IR sensor. The sensor may be
in an egg-shaped dimple in the front panel, or behind a lens (the IR
signal goes through the panel lens).
Note: The IR extender cable is the best way to get the IR signal
from the converter to the receiver because the signal doesn’t have
to go through the air.
Figure 6. IR Sensor in an egg-shaped dimple
Pyramid.book Page 6 Wednesday, February 16, 2005 4:00 PM

7
Figure 7. IR Sensor behind a lens
5. To secure the IR head, peel the paper off the strip of tape on the
head (the IR signal goes through the tape), and stick the head into
place.
6. For DISH Player-DVR 522 and DISH Player-DVR 625, place the
IR head about ¼” from the left side of the front panel lens.
Figure 8. DISH Player-DVR 522 IR sensor
7. For DISH 301, DISH 311, DISH 322 receivers, you can use the IR
head clip to set up the IR extender cable.
Figure 9. Attach the IR Extender Head to
the receiver’s bottom panel
Pyramid.book Page 7 Wednesday, February 16, 2005 4:00 PM

8
a. Attach the IR head clip to the receiver’s bottom panel, on the
grate directly behind the front panel’s IR sensor. You must
center the clip on the second slot from the left. There is a CLIP
label on the bottom panel of some DISH 301, DISH 311, and
DISH 322 receivers.
b. Fit the IR head into the IR head clip, and route the IR extender
cable out through the clip’s slot.
8. Route the IR extender cable under the back of the receiver, to the
converter.
9. You can also use just the converter to send the signal through the
air to the receiver.
Figure 9. UHF Pro signals are converted
to IR and sent through the air to the receiver
a. Make sure you put the converter no more than 20 feet away
from the receiver, and that the converter has a clear signal path
to the receiver.
b. Make sure the lens of the converter points toward the receiver’s
front panel.
10. Plug the power cord into a wall outlet.
11. Press any button on the remote control. A red light on the converter
turns on whenever it receives a signal from the remote control.
Pyramid.book Page 8 Wednesday, February 16, 2005 4:00 PM

9
SETTING UPTHE REMOTE CONTROL
INSTALLING BATTERIES
The remote control requires AAA batteries. When you
replace old batteries, you should replace all of the
batteries. Use batteries of the same kind, for example,
alkaline or carbon zinc, and don’t mix batteries of different
kinds. Alkaline batteries last longer.
1. Press down on the battery cover and slide the cover
off.
2. If you are replacing batteries, take out all of the old
batteries.
3. Put the new batteries in. Make sure
you match the plus (“+”) ends with the
plus markings on the battery case.
4. Slide the cover back into place.
SETTING UPTO CONTROL THE RECEIVER
The remote and the receiver must be set up on the same address so that
the remote can control the receiver. When you get the kit, the remote is
set up to control the receiver on address 1. However, your receiver may
be set to a different address. There are two ways to set up the remote
and receiver to work together on the same address. One way is to
simply use the address from the existing IR remote control. If you do
not have the existing IR remote control, use Changing the Receiver and
Remote Control Addresses on page 10.
1. On the existing remote control, press and hold the SAT
mode button for three seconds until all mode buttons light.
Then, let go.
2. Press the POUND (#) button twice while watching the
SAT mode button.
3. Count the number of times the SAT mode button flashes.
This number is the remote address. For example, if the
SAT mode button flashes 6 times, this indicates the
remote address is set to 6.
Write the number here: __________
Note: If using more than one UHF Pro remote control in your
house, make sure that the remote controls are set to different
addresses from each other.
Pyramid.book Page 9 Wednesday, February 16, 2005 4:00 PM

10
4. On the UHF Pro remote control that came with the kit, press
and hold the SAT mode button for three seconds until all
mode buttons light. Then, let go.
5. Use the NUMBER PAD buttons to enter the number you wrote in
step 3.
6. Press the POUND (#) button.If you entered the address
correctly, the SAT mode button will flash three times.
USING THE REMOTE CONTROL
After you have installed the converter and set up your UHF Pro remote
control, make sure that the remote can control your receiver in the
same room and also from other places where you want to use the
remote control. If the remote cannot control the receiver, see
Troubleshooting the Kit on page 42.
REMOTE CONTROL OPERATION
This section describes how to use the remote control that came with the
kit.
CHANGING THE RECEIVER AND REMOTE CONTROL
ADDRESSES
1. Open the System Information screen. Consult your receiver user's
guide for instructions on how to open this screen without using the
remote control. The System Information screen will show either
one Remote Address, or it may show a Primary Remote Address
and a Secondary Remote Address.
Note: On the DISH Player-DVR 522 and DISH 322, program the
remote control on TV1 only.
2. Press and hold the SATmode button about three seconds,
until all the mode buttons light up, and then let go of the
SAT button. The SAT mode button will blink.
3. Use the NUMBER PAD buttons to enter any number from 1 to 16.
The SAT mode button goes out after you enter each digit, and then
lights up again.
Write down the number you entered: __________
Note: If using more than one UHF Pro remote control in your
house, make sure that the remote controls are set to different
addresses from each other.
4. Press the POUND (#) button. If you entered the address
correctly, the SAT mode button will flash three times.
Pyramid.book Page 10 Wednesday, February 16, 2005 4:00 PM

11
5. Press the RECORD button.
6. Make sure the System Information screen shows the
address number you entered in step 3.
7. Close the System Information screen. On most
receivers, this is done by selecting Done. See your receiver user's
guide for more information.
CHECKING THE REMOTE CONTROL ADDRESS
To check the remote control address setting:
1. Press and hold the SAT mode button for three seconds
until all mode buttons light. Then, let go.
2. Press the POUND (#) button twice while watching the
SAT mode button.
3. Count the number of times the SAT mode button flashes.
This number is the remote address. For example, if the
SAT mode button flashes 6 times, this indicates the
remote address is set to 6.
SETTING UPTO CONTROL OTHER DEVICES
To use the remote to control other devices (such as a TV, VCR, DVD
player, tuner/amplifier, or a second DISH Network satellite receiver),
you must first program it to control these other devices. You can do this
by either following the instructions in Setting Up Using Device Code
Tables on page 12, or the Setting Up Using Device Codes Scan
procedure described on page 13.
COMBINATION DEVICES
If you are programming the remote to control a combination device,
such as a TV/VCR or a TV/DVD, program the remote control in one
mode, and then repeat the procedure in the other mode. For example, to
program the remote to control a TV/VCR using code 748, follow the
instructions to program the remote to control the TV using code 748,
and then repeat the instructions for the VCR using the same code.
LIMITED MODE
You can program your remote control in Limited Mode to keep from
accidentally changing the channel on your TV or VCR. When you use
the remote to control your TV in Limited Mode, you will only be able
to use the POWER, MUTE, and VOLUME buttons to control your TV.
Pyramid.book Page 11 Wednesday, February 16, 2005 4:00 PM

12
Also, when you use the remote to control your VCR in Limited Mode,
you will only be able to use the POWER and VCR function buttons.
The section Setting Up Using Device Codes Tables has a step that tells
the remote control to go into Limited Mode.
Note: Limited Mode can not be used with audio amplifiers.
SETTING UPUSING DEVICE CODE TABLES
You can set up the remote to control other devices using the device
codes listed on page 33.
1. Use the device’s buttons or its remote control to turn on the
device.
2. Find the brand name of the device in the tables starting on
page 33.
If the brand isn’t listed, see Setting Up Using Device Codes Scan
on page 13.
3. Press and hold the mode button for the device you want
the remote to control, for about three seconds. When all the other
mode buttons light up, let go of the mode button - that mode button
should now be flashing.
For example, hold the TV mode button for a TV until all of the
other mode buttons light. When you let go, the TV mode light will
flash.
4. Only for the AUX mode, Use a number button to enter 0 for a
second TV, or 1for a second VCR or DVD player, or 2for a tuner
or amplifier.
5. Use the number buttons to enter one of the device
codes from the table.
6. Only for Limited Mode, Press 1.
Note: Skip this step if you do not want to use
Limited Mode.
7. Press the POUND (#) button. If you entered the
code correctly, the mode button flashes three times.
8. Press the blank POWER button to test if the code
works for the device. If it does, the device should turn
off.
Pyramid.book Page 12 Wednesday, February 16, 2005 4:00 PM

13
9. Turn the device back on and try some other buttons to make sure
they work. Sometimes, the blank POWER button works when
other buttons don’t. If the code works for other buttons, stop here.
10. If the code you entered doesn’t work, do steps 3 through 9 again
with another device code from the tables.
11. If you cannot find a code that works, try Setting Up Using Device
Code Scan.
SETTING UPUSING DEVICE CODE SCAN
If the code for your device is not listed in the tables starting on page 33,
use this procedure to scan the remote control’s memory for the device
code.
1. Use the device’s buttons or its remote control to turn the device on.
2. Press and hold the mode button for the device you want the remote
to control, for about three seconds. When all the other mode
buttons light up, let go of the mode button - that mode button
should now be flashing.
For example, hold the TV mode button for a TV until all of the
other mode buttons light. When you let go, the TV mode light will
flash.
3. Only for the AUX mode, use the number buttons
to enter 0for a second TV, 1 for a second VCR or DVD
player, or 2 for a tuner or amplifier. Then press the
STAR (*) button.
4. Press the blank POWER button.
5. Press the up or down arrow button until the
device turns off. You will have to do this
repeatedly to scan through all codes.
Note: The mode button for the device will flash
rapidly eight times when you’ve scanned all the
codes for that device.
6. If the remote reaches the correct code, the device turns
off. When this happens, press the POUND (#) button to
store the code in the remote.
Pyramid.book Page 13 Wednesday, February 16, 2005 4:00 PM

14
7. Press the blank POWER button to turn the device
back on.
8. Try some other buttons to make sure they work.
Sometimes, the blank POWER button works when
other buttons don’t.
PROGRAMMING THE REMOTE TO CONTROL
ASECOND SATELLITE RECEIVER
If you have another DISH Network satellite receiver installed, you can
use this remote in AUX mode to control the second receiver. You can
program the remote to control any other DISH Network satellite
receiver, except for following:
•DISH 322 - TV2
•DISH Player-DVR 522 - TV2
•DishPlayer 7100/7200
1. Turn on the other receiver and display the System Info screen (see
the user’s guide for information on how to display the screen).
Write the address: _____________
2. Press and hold AUX until all the other mode buttons light
up, and then let go of the button. AUX flashes.
3. Press the 3 button.
4. Use the NUMBER PAD to enter the address you wrote in step 1.
5. Press POUND (#). AUX blinks three times.
6. Press RECORDto make sure the address and the remote
matches the address on the receiver
CHECKING THE DEVICE CODES
You can find out what device code you’ve set for each remote control
mode.
1. Press and hold the mode button for the device you want the remote
to control, for about three seconds. When all the other mode
buttons light up, let go of the mode button - that mode button
should now be flashing.
For example, hold the TV mode button for a TV until all of the
other mode buttons light. When you let go, the TV mode light will
flash.
Pyramid.book Page 14 Wednesday, February 16, 2005 4:00 PM

15
2. Press the POUND (#) button twice. The mode button
flashes the number for each digit of the device code, with
a pause between the groups of flashes. A quick flash is for
zero. For example, if the code is 570, the mode button
flashes five times, pauses, flashes seven times, pauses, and flashes
once quickly.
For AUX mode, the first group of flashes tells you what the AUX
mode controls. A quick flash (zero) before the three-digit code is
for a TV; one regular flash is for a VCR or DVD player; and two
flashes is for a tuner or amplifier. For example, if the TV code is
570, the AUX mode button flashes once quickly, pauses, flashes
five times, pauses, flashes seven times, pauses, and flashes once
quickly.
SWITCHING BETWEEN TV AND DEVICE VOLUME
CONTROL
When you set up the remote to control a TV, the MUTE and VOLUME
buttons control the TV volume. However, if you want to use the AUX
mode to control a tuner or amplifier and the device has a volume
setting, you can set up the remote to control the device’s volume
instead of the TV volume.
To set the remote to control the device’s volume:
1. Press and hold the AUX mode button
for three seconds, and then let go of it. The AUX mode
button will blink.
2. Press the POUND (#) button.
3. Press the plus (+) side of the VOLUME
button.
4. Press the 0number button.
5. Press the POUND (#) button.
The AUX mode button flashes three times.
6. Press the SAT mode button.
Pyramid.book Page 15 Wednesday, February 16, 2005 4:00 PM

16
7. Press the plus (+) and minus (-) sides of the
VOLUME button. The device’s volume
changes and the AUX mode button lights
instead of the TV mode button.
To set the remote back to control the TV volume:
1. Press and hold the TV mode button for three seconds, and
then let go of it. The TV mode button will blink.
2. Press the POUND (#) button.
3. Press the plus (+) side of the VOLUME
button.
4. Press the 0number button.
5. Press the POUND (#) button.
The TV mode button flashes three times.
6. Press the SAT mode button.
7. Press the plus (+) and minus (-) sides of the
VOLUME button. The TV’s volume changes
and the TV mode button lights instead of the
AUX mode button.
Pyramid.book Page 16 Wednesday, February 16, 2005 4:00 PM

17
OPERATING MODES
You can set the remote to four different modes to control the receiver
or other devices. You may need to change the remote address to operate
the receiver. See Setting Up to Control the Receiver on page 9. You
must set up the remote to control a device like a TV, VCR, or DVD
player. See Setting Up to Control Other Devices on page 11.
Use the remote control’s mode buttons, SAT (satellite receiver), TV
(for a TV), VCR (for a VCR or a DVD player), and AUX (“auxiliary,”
for a second TV, a second VCR, a tuner, or an audio amplifier) to set
the remote to the right mode for the device.
To change the mode, press the button for the device you want the
remote to control. The mode button lights for two seconds to show
you’ve set the remote to that mode.
CONTROLLING THE SATELLITE RECEIVER
SAT MODE BUTTON
Press this button to set the remote to SAT (“satellite”) mode to control
the receiver. The SAT mode button’s back light stays lit for about two
seconds to show you’ve set the remote to SAT mode. Make sure you
keep the remote in SAT mode to use the following buttons.
Note: The information in this section also applies when the AUX mode
button is programmed for a second satellite receiver and the remote is in
AUX mode.
Note: Your satellite receiver may not provide all of the functions
described as follows. Consult your receiver user’s guide for the
features your receiver provides.
TV/VIDEO BUTTON
If you connect the receiver with its back panel TV ANTENNA/CABLE
IN and TV SET OUT ports, use this button to switch the receiver
between the satellite signal (connect it to the SATELLITE IN port) and
another video signal like a cable or broadcast TV antenna input
(connect it to the receiver’s TV ANTENNA/CABLE IN input).
Your receiver may use this button as an SD/HD INPUT button to
toggle between HD and SD Output mode on high definition satellite
receivers. Consult your receiver user’s guide for how to use this button.
Pyramid.book Page 17 Wednesday, February 16, 2005 4:00 PM

18
POWER BUTTONS
Press the blank POWER button to turn the receiver on or off.
Press the TV POWER button to turn your TV off and on.
Note: You must set up the remote to control the TV for the
TV POWER button to work. See Setting Up to Control Other
Devices on page 11.
VOLUME BUTTON
Press this button to raise (+) or lower (-) the TV sound volume.
Note: You must set up the remote to control the TV for the VOLUME
button to work. See Setting Up to Control Other Devices on page 11.
MENU BUTTON
Press this button to open the Main Menu.
MUTE BUTTON
Press this button to turn the TV sound on or off.
Note: You must set up the remote to control the TV for the MUTE
button to work. See Setting Up to Control Other Devices on page 11.
PAGE UPAND PAGE DOWN BUTTONS
Press the PAGE UP button or the PAGE DOWN button to scan, page
by page, through the Program Guide, a Themes list, a Favorites List,
an Event Timers list, or a list of channels.
Note: An “event” is any satellite program.
Pyramid.book Page 18 Wednesday, February 16, 2005 4:00 PM