Dish Network BASIC REMOTE User manual

Basic Remote

Safety Instructions
You must keep safety in mind while using this device. Keep
these and any other instructions for future reference.
Observe Warnings: Carefully follow all warnings on the device
and in the operating instructions.
Heat: Do NOT place the device near heat sources such as
radiators, stoves, heat registers, or other appliances that
produce heat.
Care and Use
Cleaning: Do NOT use liquid, abrasive, solvent, or aerosol
cleaners. Use a damp cloth for cleaning.
When Not in Use: Remove the batteries if this device is to be
left unattended or unused for a long period of time.
Refer servicing to qualied personnel when a
solid object or liquid has fallen onto or into the
device.
Do NOT attempt to service this device. Refer all
servicing to qualied personnel. Opening covers
other than the battery cover will void the warranty.
Publishing Information
Copyright © 2010. EchoStar Technologies L.L.C., Englewood,
Colorado 80112. All rights reserved.
The information in this User Guide may change without notice.
Revisions may be issued to tell you about such changes.
Address comments or questions about this User Guide to
[e-mail] or
Technical Publications, EchoStar Technologies L.L.C, 90
Inverness Drive Circle East, Englewood, Colorado 80112.
Document Number: 183120
Printed in
DISH Network is a trademark and service mark of DISH
Network.
All product names, trade names, or corporate names
mentioned in this User Guide are acknowledged to be the
proprietary property of the registered owners.

1
SAT Mode
VOLUME and
MUTE Buttons
Controls TV
volume
SAT Power
Controls satellite
receiver
Red Light
Assists in
programming
mode
DVR
Goes to list of
recorded
programs
DVR
Pauses live TV
and plays
or records
programming
Channel
Up/Down
Navigates
through
channels
RECALL
Returns to the
last channel
viewed
System Wizard
Stores and/or
restores remote
settings
Number
Buttons
Enters a
channel number,
or navigates
through menus
MENU
Accesses
features and
settings
INFO
Retrieves
information
on programs
TV Power
Controls TV
CANCEL
Returns to
previous menu
or to watching
a program
GUIDE
Displays
current and
future satellite
program listings
Arrows/OK
Buttons
Navigates
through menus
and program
guide, and use
to select a
desired option

2
DVR Functions
Press twice to go to list of recorded
programs.
Pauses or plays a live or recorded
program.
Stops recording a program.
Records a program.
Press and release to skip backward
through recorded programs. Press
and hold before releasing to rewind
quickly (x4). If pressed and released
once in rewind mode, rewinding video
increases to second speed (x60).
Press and release to skip forward
through recorded programs. Press
and hold before releasing to fast-
forward quickly (x4). If pressed and
released once in fast forward mode,
forwarding video increases to second
speed (x60).
Note: If video is rewinding or forwarding at x4
speed and the opposite button is pressed, the
video switches to other direction.
If video is rewinding or forwarding at x60
speed and the opposite button is pressed, the
video decreases to x4.
Note: DVR Functions only work with DISH Network
receivers that support DVR.

3
Insert the Batteries
Remove the remote
battery cover.
Insert 4 AA batteries,
making sure to match the
plus (+) ends with the plus
markings on the battery
case.
Replace the remote
battery cover. With the
cover at a slight angle,
line up the tabs and push
down on the cover until it
is in place.
Press the POWER button
on the receiver’s front
panel.
Conrm remote operates
the receiver by pressing
other remote buttons.
1
1
2
2
3
Making the Remote Work
with the Receiver

4
Programming Remote to Control TV
(Entering a TV code)
Turn TV and receiver on.
Find the brand name of the
TV listed in the code tables
that start on page 11.
Press and hold TV
POWER until red light
comes on. Release TV
POWER. Red light blinks.
Enter a three-digit TV
code (see page 11) that
corresponds to your TV
brand, using the number
buttons on the remote’s
number pad. Red light
remains on after entering
the code.
Press and release OK.
Red light blinks three
times.
Con’t on next page...
1
2
3
4
5
TV Codes
These tables contain the manufacturer codes for
programming the remote control to operate your TV.
Every attempt has been made to include all codes. If
your equipment brand is not listed or if the codes do
not work, the remote may not control your equipment.
In some cases codes may operate some but not all
buttons shown in this guide.
Abex 658 730
Acer 511
Action 662
Admiral 521 572 675
739 834 835
Advent 653 842 912
Adventura 840
Aiko 727 778
Aiwa 667
Akai 570 573 592 612
627 652 754 795 807
808 906 907 908
Alaron 534
Albatron 692 804
Alleron 534
A-Mark 620 804
Ambassador 686
America Action 682
Amtron 657
Ampro 691
Anam 682
Anam National 509
541 620 651 657 662
AOC 505 506 519 520
573 582 620 627 653
654
Apex 552 595 743 744
745 757 771 802 815
Archer 620 804
Astar 594
Audiovox 528 565 620
623 624 657 662 682
778 832
Aventura 733
Axion 636
Bang & Olufsen 514
665
Baycraft 536
Baysonic 682
Belcor 627 773
Bell & Howell 590 675
683
Benq 511 535
Bradford 657 682
Brillian 558
Brockwood 627
Broksonic 682 748 750
752 754 834 899 908
ByD:sign 792
Candle 506 523 525
536 627 654 840
Candle/Citizen 573
Capehart 519 627
Carnivale 627
Carver 761
CCE 528 816
Celebrity 652 795 797
798 807
Celera 744 745
Changhong 744 745
Cineral 697
Circuit City 627
Citizen
506 516 523 524
525 590 627 654 657
658 664 680 727 778
Clairtone 698
Clarion 682
Coby 626 633
Colortyme 573 627 654
Colt 660
Commercial Solutions
645 650
Concerto 523 652 654
Contec 682
Contec/Cony 541 655
657 658 662

5
Programming Remote to Control TV
(Entering a TV code continued)
Press and release TV
POWER to turn off the TV.
If TV turns off, continue to
step 7. If the TV does not
turn off, go to Step 8.
Turn the TV on and try
other buttons to make
sure they work. If the other
buttons work, stop here. If
they do not work, continue
to Step 8.
If the code does not work,
repeat Steps 3 through 7
with another TV code for
your brand of TV listed in
the table starting on
page 11.
If you are unable to
nd a code that works,
try the instructions for
Automatically nding a TV
code on page 6.
6
7
8
9
TV Codes
These tables contain the manufacturer codes for
programming the remote control to operate your TV.
Every attempt has been made to include all codes. If
your equipment brand is not listed or if the codes do
not work, the remote may not control your equipment.
In some cases codes may operate some but not all
buttons shown in this guide.
Abex 658 730
Acer 511
Action 662
Admiral 521 572 675
739 834 835
Advent 653 842 912
Adventura 840
Aiko 727 778
Aiwa 667
Akai 570 573 592 612
627 652 754 795 807
808 906 907 908
Alaron 534
Albatron 692 804
Alleron 534
A-Mark 620 804
Ambassador 686
America Action 682
Amtron 657
Ampro 691
Anam 682
Anam National 509
541 620 651 657 662
AOC 505 506 519 520
573 582 620 627 653
654
Apex 552 595 743 744
745 757 771 802 815
Archer 620 804
Astar 594
Audiovox 528 565 620
623 624 657 662 682
778 832
Aventura 733
Axion 636
Bang & Olufsen 514
665
Baycraft 536
Baysonic 682
Belcor 627 773
Bell & Howell 590 675
683
Benq 511 535
Bradford 657 682
Brillian 558
Brockwood 627
Broksonic 682 748 750
752 754 834 899 908
ByD:sign 792
Candle 506 523 525
536 627 654 840
Candle/Citizen 573
Capehart 519 627
Carnivale 627
Carver 761
CCE 528 816
Celebrity 652 795 797
798 807
Celera 744 745
Changhong 744 745
Cineral 697
Circuit City 627
Citizen
506 516 523 524
525 590 627 654 657
658 664 680 727 778
Clairtone 698
Clarion 682
Coby 626 633
Colortyme 573 627 654
Colt 660
Commercial Solutions
645 650
Concerto 523 652 654
Contec 682
Contec/Cony 541 655
657 658 662
Programming Remote to Cont rol TV
(S ca nning the remote da tabase )
1
Press either UP ARROW or
DOWN ARROW on remote
until TV turns off. LED goes
out and comes back on. If
the TV turns off, continue to
the next step. If the TV
remains on, keep pressing
UP ARROW or DOWN
ARROW.
Press TV POWER button.
Turn TV on.
Press and hold TV POWER
button for three seconds.
Once LED flashes, release
the TV POWER button.
2
3
Press OK. LED flashes
three times.
4
6
5
Press TV POWER button
to turn TV on and try other
buttons to make sure the
TV responds the way you
expect. If you want to try
another code, begin from
Step 1 again.
4

6
Programming Remote to Control TV
(Automatically nding a TV code)
Turn TV and receiver on.
Press and hold TV POWER
until red light comes on.
Release TV POWER. Red
light blinks.
Press and release TV
POWER. Red light stays on.
Press and release UP
ARROW slowly. Red light
goes out and comes back on.
If the TV turns off, continue
to Step 5. If the TV remains
on, repeat this step until the
TV turns off. Point the remote
at the TV the entire time.
Press and release OK. Red
light blinks three times.
Press TV POWER to turn TV
on and try other buttons to
make sure the TV responds
the way you expect. If not, try
another code by returning to
Step 1.
1
2
3
4
5
6
Note: Only use Automatically nding a TV code if you
were unable to nd a code using Entering a TV code.

7
Displaying TV Code
To identify the TV code that your Basic Remote is
using, complete the following steps:
Press and hold TV
POWER until red light
comes on. Release TV
POWER. Red light blinks.
Press and release OK
twice.
The red light blinks
a number of times
corresponding to the value
of the stored TV code. For
example, if the stored TV
code is 593, the red light
blinks ve times, pauses,
blinks nine times, pauses,
and blinks three times. For
a zero value, the red light
blinks quickly (different
blink from a value of 1).
Record the stored TV code
in the Reference Table on
the inside back cover.
1
2
3
4Refe rence Tables
Write down your channel numbers/inputs
and TV code as you program them for future
reference.
Channel or Input for
Satellite Programming
TV Code

8
SAT Auto-Tune
Make sure the remote control
operates your TV.
Press and hold TV POWER until
red light comes on. Release TV
POWER. Red light blinks.
Press and release RECALL.
Enter the channel used for
viewing (three digits in range
of 002 to 125), for example
channel “003.”
Press and release OK.
1
2
3
4
5
Setting SAT Auto-Tune Channel
SAT Auto-Tune programs into the remote control
the correct TV channel used for viewing your paid
programming. If you are experiencing fuzzy, blue, or
black screens, it might be due to the TV being set to the
wrong channel. Using the SAT Auto-Tune feature helps
prevent fuzzy, blue, or black screens from occurring.
When TV POWER is pressed and released, the remote
sends that channel to the TV, ensuring that the TV is on
the correct channel for viewing your paid programming.
To use this feature, you must program the channel
by following the steps under Setting SAT Auto-Tune
Channel.