Dish Network digital remote control User manual



User Guide
A single remote to control up to four devices.

IMPORTANT REGULATORY FACTORS
WIRELESS REMOTE CONTROL
This device complies with Part 15 of Federal Communications
Commission (FCC) Rules. Operation is subject to the following
conditions:
•This device may not cause harmful interference.
•This device must accept any interference that may cause
undesired operation.
•Unauthorized equipment changes may void FCC certification.
IMPORTANT SAFETY INSTRUCTIONS
You must keep safety in mind while using this device. Keep these and
any other instructions for future reference.
Installation
Observe Warnings: Carefully follow all warnings on the device
and in the operating instructions.
Heat: DO NOT place the device near heat sources such as
radiators, stoves, heat registers, or other appliances that
produce heat.
Care and Use
Cleaning: DO NOT use liquid, abrasive, solvent, or aerosol
cleaners. Use a damp cloth for cleaning.
When Not in Use: Remove the batteries if this device is to be
left unattended or unused for a long period of time.
Refer servicing to qualified personnel
when a solid object or liquid has fallen
onto or into the device.
DO NOT attempt to service this device.
Refer all servicing to qualified personnel.
Opening covers other than the battery cover
will void the warranty.

104333 1
TABLE OF CONTENTS
About the Remote Control...............................page 2
Remote Control Signals: UHF or IR.................page 2
Installing Batteries in the Remote Control........page 3
Remote Control Modes....................................page 3
Using the Remote Control Buttons ................page 4
SAT (Satellite Receiver) Mode.........................page 4
TV (Television) Mode .......................................page 8
VCR (VideoCassette Recorder) Mode.............page 10
AUX (Auxiliary) Mode for Cable TV Box..........page 12
AUX (Auxiliary) Mode for Tuner or Amplifier....page 13
Remote Control Procedures............................page 15
Controlling a Device.........................................page 15
Changing the Remote Control Address ...........page 16
Installing an Attenuator....................................page 17
Controlling Sound Volume................................page 18
Receiver Volume Control......................page 18
TV or Amplifier Volume Control............page 19
Doing the Device Code Scan...........................page 20
Finding the Device Codes................................page 21
Device Codes ...................................................page 22
TVs...................................................................page 22
VCRs................................................................page 23
DVD Players......................................................page 25
Tuners and Amplifiers......................................page 25
Cable TV Boxes...............................................page 25
Trouble-Shooting Table ...................................page 26
Limited Warranty ..............................................page 28
If You Need Help ...............................................page 30

Remote Control Signals: UHF or IR
2 104333
ABOUT THE REMOTE CONTROL
The remote control gives you easy access to all the features of a
DISH NetworkTM satellite TV system. You can set up the remote
to control up to three devices other than the satellite TV receiver.
The three devices may include a TV, a VCR, a DVD player, a cable TV
box, a tuner, or an audio amplifier.
REMOTE CONTROL SIGNALS: UHF OR IR
•The remote control uses Ultra-High Frequency (UHF) radio
signals to control the satellite TV receiver. UHF signals travel
long distances (100 feet or more) and go through walls and other
solid objects. Because UHF signals travel so far, the receiver
may respond to signals from other nearby remote controls.
To handle this problem, see Changing the Remote Control
Address on page16. If this does not work, see Installing an
Attenuator on page17.
•To use the remote to control the receiver, youmust attach the
UHF antenna to the receiver back panelUHF Remote Antenna
connection.
Note: To be able to use the remote control over the longest
possible distance, place the antenna straight up. Donot let the
antenna touch anything.
•The remote control uses Infra-Red (IR) light signals to control
devices other than the receiver. IR signals travel only short
distances (40 feet or less), and cannot go through walls or other
solid objects. You must point the remote control directly
at the device, with no objects blocking the line of sight.

Installing Batteries in the Remote Control
104333 3
INSTALLING BATTERIES IN THE
REMOTE CONTROL
The remote control comes with AAA batteries,
packaged separately. When you replace old batteries,
you should replace all of the batteries. Use batteries
of the same grade, for example, alkaline or carbon
zinc, and do not mix batteries of different grades.
Alkaline batteries provide longer battery life.
1.Press down on the slot in the battery cover
(on the back of the remote control) and slide
the cover off.
2.Insert the new batteries, making sure to match
the plus (“+”) ends with the plus markings
on the battery case.
3.Replace the battery cover by sliding the cover
back up into place.
REMOTE CONTROL MODES
To use the remote to control a device such as the satellite receiver or a
TV, you must first set up the remote to control the device,and then set
the remote to the right mode for that device.
1. Set up the remote to control the device. See Controlling a Device
on pag e15 for instructions.
2.Use the remote control mode buttons,SAT (satellite receiver),
TV, VCR (for a VCR or a DVD player), andAUX (“auxiliary,”
for a cable TV box, a tuner, or an audio amplifier) to set the
remote to the right mode for the device. To change the mode
setting, press the button for the device that you want the remote
to control. The mode button’s back light turns ON to show that
the remote is set to that mode.
The following sections describe how to use the
remote control buttons. Each section describesonly
the buttons that work inone remote control mode,
for example SAT mode or TV mode.

SAT (Satellite Receiver) Mode
4 104333
USING THE REMOTE CONTROL BUTTONS
SAT (SATELLITE RECEIVER) MODE
SAT MODE BUTTON
The remote control already is set up to control the satellite receiver.
But, you must press the SAT mode button to set the remote to SAT
mode. The SAT mode button’s back light turns ON to show that the
remote is set to SAT mode. Make sure to keep the remote inSAT
mode to use the buttons as described in this section.
AUX MODE BUTTON
Set up the remote to control the television and donot setup the remote
in AUX mode. If you do this, then with the remote in SAT mode you
can press the AUX mode button to turn the television ON or OFF.
This allows you to turn the TV on or off without leaving SAT mode.
TV/VIDEO BUTTON
If you connect the receiver using only its back panel RF or VHF
connections, use this button to switch the receiver between the satellite
signal (routed into the receiver’s Satellite In input) and another video
signal such as cable or broadcast TV antenna input (routed into the
receiver’s TV Antenna Cable In input).
MENU BUTTON
Press this button to open the Main Menu.
Some of the features described below may not
apply to your satellite receiver. See the receiver
User Guide for details about the receiver’s features.
If a remote control button is not described in this
section, it does not work in SAT mode.

SAT (Satellite Receiver) Mode
104333 5
POWER BUTTON
Press this button to turn the receiver ON or OFF. The greenPower
light on the receiver front panel lights up to show that the receiver
is ON, and goes out to show that the receiver is OFF.
PAGE UPAND PAGE DOWN (ARROW) BUTTONS
Press the Page Up button or the Page Down button to scan, page
by page, through the Program Guide, a Themes menu,
a Favorite List, an Event Timers list, or a list of channels.
MUTE BUTTON
Press this button to turn off the sound. Press it again to restore
the sound.
VOLUME BUTTON
Press the left-hand, minus (-) side of this button to lower the sound
volume. Press the right-hand, plus (+) side of this button to raise the
sound volume.
GUIDE BUTTON
Press this button to open the Program Guide. When the Program
Guide is open, press this button to switch among Favorite Lists.
SELECT BUTTON
Press this button to select a highlighted option or program in a menu.

SAT (Satellite Receiver) Mode
6 104333
UP/DOWN/LEFT/RIGHT
(ARROW) BUTTONS
•When using a menu, press these buttons to move the highlight
to an option.
•When watching a program, press the Right button to open the
Browse Banner or the Up or Down button to change channels.
•When the Browse Banner is open, press the Up or Down
button to see the Browse Banner for the next channel.
•When a menu offers a list of choices (different from menu
options), press the Up or Down button to see more choices.
•When the Program Guide is open, press these buttons to move
the highlight among the programs.
•To enter a number in a menu, highlight the place where you need
to enter the number. Then, press the Up or Down button
to increase or decrease the number in the highlighted field.
Or, you may use the Number Buttons.
•When the Browse Banner is open, press the Right or Left
button to display the current program or the next program on a
channel.
•When watching a program, press the Left button to open the
Themes menu.
RECALL BUTTON
Press this button to return to the last channel you were watching.
Press it again to switch between the last two channels that you
watched.

SAT (Satellite Receiver) Mode
104333 7
INFORMATION (INFO) BUTTON
•Press this button for more information when the
Program Guide or the Browse Banner is open, or when
watching a program.
•When a menu is open that includes aHelp option, press this
button to see help information for that menu.
•Highlight a program in a Themes list and then press this button
for more information on that program.
•When the receiver is OFF, press this button to display the
Important System Information menu.
VIEW BUTTON
•Press this button to return to watching a program.
•If you are watching a program, press this button to briefly display
the Program Banner.
•While using any menu, press this button to cancel a procedure
and return to watching a program.
CANCEL BUTTON
Press this button to cancel a procedure and to return to the previous
menu or to watching a program.
SYSTEM INFORMATION (SYS INFO) BUTTON
Press this button to display the Important System Information
menu.

TV (Television) Mode
8 104333
NUMBER BUTTONS
•When watching a program or with theProgram Guide open,
use these buttons to enter a channel number to change to that
channel.
•When the Program Guide is open, enter a number of hours
using these buttons, and then press the Right or Left arrow
button to skip the display backward or forward by that number
of hours.
•Use these buttons to enter menu option numbers. For an option
that has a number, you may do thisinstead of highlighting the
option and then pressing the Select button.
•Use these buttons to enter numbers in a menu. To do this,
first highlight the place where you need to enter the number.
Next, press a number button (or, you can use theUp/Down
arrow buttons to enter the number). Then, move the highlight
to the place for the next number that you need to enter, or press
the Select button if you are done entering numbers.
POUND BUTTON
Use this button in Changing the Remote Control Address on pag e16.
TV (TELEVISION) MODE
Some of the features described below may not
apply to the TV. See your TV owner’s manual
for details about the TV’s features. If a remote
control button is not described in this section, it
does not work in TV mode.