DITEC PWR50AC User manual

Technical Manual
Ditec PWR50AC
Automation for swing gates
(Translation of the original instructions)
IP2352EN • 2020-02-25
www.ditecentrematic.com

2
IP2352EN
EN
Contents
Key
Subject Page
1. General safety precautions 3
2. Declaration of incorporation of partly completed machinery 4
2.1 Machinery Directive 4
3. Technical specifications 5
4. Standard installation 7
5. Dimensions and gearmotor references 8
6. Installation 9
6.1 Preliminary checks 9
6.2 Fastening the brackets 10
6.3 Using the positioning template 11
6.4 Installing the gearmotor 12
6.5 Adjusting the mechanical end stop 13
6.6 Adjusting electromechanical limit switch (optional) 13
6.7 Reversible and irreversible piston 14
6.8 Electrical connections 14
6.9 Motor connection diagram 15
7. Routine maintenance plan 16
8. Troubleshooting 16
9. Disposal 16
i
This symbol indicates instructions or notes regarding safety, to which special atten-
tion must be paid.
This symbol indicates useful information for the correct operation of the product.

3
IP2352EN
EN
1. General safety precautions
Failure to respect the information given in this manual
may cause personal injury or damage to the device.
Keep these instructions for future reference
This installation manual is intended for qualified personnel only.
Installation, electrical connections and adjustments must be performed in accordance
with Good Working Methods and in compliance with the present standards.
Read the instructions carefully before installing the product.
Incorrect installation could be dangerous.
Before installing the product, make sure it is in perfect condition.
Before installing the motorisation device, make all the necessary structural modifi-
cations to create safety clearance and to guard or isolate all the crushing, shearing,
trapping and general hazardous areas.
Make sure the existing structure is up to standard in terms of strength and stability.
The motorisation device manufacturer is not responsible for failure to observe Good
Working Methods when building the frames to be motorised, or for any deformations
during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed
taking into account the applicable laws and directives, Good Working Methods, installa-
tion premises, system operating logic and the forces developed by the motorized gate.
The safety devices must protect the crushing, shearing, trapping and general haz-
ardous areas of the motorised door.
Display the signs required by law to identify hazardous areas.
Each installation must bear a visible indication of the data identifying the motorized
gate.
When requested, connect the motorized gate to an effective earthing system that
complies with current safety standards.
During installation, maintenance and repair operations, cut off the power supply before
opening the cover to access the electrical parts.
The automation protection casing must be removed by qualified personnel only.
The manufacturer of the motorisation device declines all responsibility if com-
ponent parts not compatible with safe and correct operation are fitted.
Only use original spare parts when repairing or replacing products.
The installer must supply all information on the automatic, manual and emergency
operation of the motorised gate, and must provide the user with the operating in-
structions.

4
IP2352EN
EN
2. Declaration of incorporation of partly com-
pleted machinery
(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB, with headquarters in Lodjursgatan 10, SE-261 44
Landskrona, Sweden, declares that the Ditec PWR50AC automation for swing gates:
- is designed to be installed on a manual gate to form a machine pursuant to Directive 2006/42/
EC. The manufacturer of the motorised gate must declare conformity with Directive 2006/42/
EC (annex II-A) prior to initial machine start-up;
- complies with the applicable essential safety requirements indicated in Annex I, Chapter 1 of
the Directive 2006/42/EC;
- complies with the Electromagnetic Compatibility Directive 2014/30/EU;
- complies with the RED Directive 2014/53/EU;
- the technical documentation complies with Annex VII-B of the Directive 2006/42/EC;
- the technical documentation is managed by the Technical Office of Entrematic Italy (with head-
quarters in Largo U. Boccioni 1 – 21040 Origgio (VA) – ITALY) and is available upon request,
sending an e-mail to [email protected]om;
- a copy of the technical documentation will be given to competent national authorities, following
a suitably justified request.
Landskrona, 2019-11-19 Matteo Fino
(Chairman)
2.1 Machinery Directive
Pursuant to the Machinery Directive (2006/42/EC), the installer who motorises a door or gate has
the same obligations as the manufacturer of machinery and as such must:
- prepare the technical data sheet which must contain the documents indicated in Annex V of the
Machinery Directive;
- (the technical data sheet must be kept and placed at the disposal of competent national au-
thorities for at least ten years from the date of manufacture of the motorised door or gate);
- draw up the EC Declaration of Conformity in accordance with Annex II-A of the Machinery Di-
rective and deliver it to the customer;
- affix the EC marking on the motorised door or gate, in accordance with point 1.7.3 of Annex I of
the Machinery Directive.

5
IP2352EN
EN
3. Technical specifications
Tab. 3.0
Chart 3.0
Usage limits (gate wing weight and width)
1
0
100
200
300
400
500
600
700
800
23
(m)
(Kg)
45
Type Irreversible/Reversible
Stroke management
(limit switch) Mechanical close stop (opening)
Power supply 230V ~ / 50Hz
Max absorption 1,1A
Power absorbed 250W
Max thrust 6000N
Maximum stroke 500mm
Opening time 32s / 90°
Intermittence 200 cycles/day [max] - 30 consecutive cycles at 20°C
Lifespan From 150,000 to 450,000 cycles based on the conditions indicated in table 3.1 (see
the durability graphs of the product)
Operating temperature -20°C / +55°C (-35°C + 55°C with NIO active)
Degree of protection IP44
Dimensions (mm) 1044x100x124h
Weight (kg) 10,5

6
IP2352EN
EN
0
10
20
30
40
50
60 70
80
90
100
0
50.000
indice di gravosità (%)
250.000
300.000
350.000
100.000
150.000
200.000
400.000
450.000
500.000
550.000
600.000
n° massimo di cicli
Example of the operator durability calculation is shown below:
Severity index (%)
Index of conditioning factors
Gate wing weight
>400 Kg 10
>550 Kg 20
>650 Kg 30
Gate wing width > 3 m 10
> 4 m 20
Solid gate wing 15
Windy area 15
VA/VC/PO/PC speed setting higher than the default
values 10
Force R1/R2 setting higher than the default values 10
Durability of the product
0
10
20
30
40
50
60 70
80
90
100
0
50.000
indice di gravosità (%)
250.000
300.000
350.000
100.000
150.000
200.000
400.000
450.000
500.000
550.000
600.000
n° massimo di cicli
Tab. 3.1 Tab. 3.2
The product lifespan is conditioned by the extent of other onerous conditions:
with reference to Tab. 3.1, various corrective factors have been assessed in relation to the weight
and width of the gate wing and the usage conditions; when taken as a whole, they affect the
lifespan of the object (see Tab. 3.2).
Example of the duration calculation
Wing weight= 300Kg 0
Wing width= 5m 20
R1/R2 = 80 (default 50) 10
Solid wing= NO 0
Total severity index 30
Estimated duration 240.000 cycles
max no. of cycles

7
IP2352EN
EN
4. Standard installation
Ref. Description Cable
1Transmitter /
2Flashing light 2 x 1mm²
Antenna (integrated in the flashing light) coaxial 58Ω
3Key selector switch 4 x 0.5mm²
Digital combination wireless keypad /
4Actuator 4 x 1.5mm²
5Photocells 4 x 0.5mm²
6Control panel 3G x 1.5mm²
A
Connect the power supply to a type-approved omnipolar switch (not supplied), with a
contact opening distance of at least 3mm.
Connection to the mains must be via an independent channel, separated from the con-
nections to the command and safety devices.
1
4
6
A
32
5
5
4
5

8
IP2352EN
EN
5. Dimensions and gearmotor references
Ref. Description
7Rear cover
8Release lock window
9Screw for fastening the rear cover
10 Screw for fastening the front cover
11 Front cover
12 Mechanical close stop
13 Drive screw
14 Split nut
124
100
525
1044
10
11
9
13
14
12
7
8
Fig. 5.1

9
IP2352EN
EN
6. Installation
The declared operating and performance features can only be guaranteed with the use of Ditec
accessories and safety devices.
Unless otherwise specified, all measurements are expressed in mm.
6.1 Preliminary checks
Make sure the gate structure is sturdy and the hinges are lubricated and smooth.
If possible, fit an opening and closing stop. Otherwise, use mechanical stops (built-in for opening
stop, optional for closing stop) and/or the electromechanical limit switches (optional) if available.
The mechanical construction elements must comply with the requisites of Standard EN12604.
i
The automation fastening point varies according to the space available and the gate
to be automated. The installer must therefore choose the best solution to ensure
that the system works correctly in each individual situation.
The installation measurements indicated in the table allow you to choose the values of [A] and [B] on
the basis of the required opening angle and in relation to the on-site spaces and overall dimensions.
Increasing measurement [A], you reduce the opening approach speed.
Reducing measurement [B], you increase the gate opening angle.
Measurements [A] and [B] must, however, be compatible with the effective piston stroke.
A
P
D
E
L
B
C
min 60 with 90° opening
S
Tab. 6.1
A B C S D E L P min
200 190 20 170 120°
120 910
220
200 200 50 150 110° 220
100 220 50 170 90° 120
130 210 70 140 95° 150
170 220 100 120 95° 190
200 190 100 90 100° 220
150 220 150 70 95° 170
130 290 220 70 90° 150

10
IP2352EN
EN
6.2 Fastening the brackets
After selecting the most suitable point for fastening the front bracket [18] to the gate wing, to
establish its height you must first size, position and fasten the rear bracket [17].
If necessary, shorten the rear bracket [17] following the indications given in Tab. 6.1.
- Once you have fastened the rear bracket [17] following the measurements given on page 9,
fasten the front bracket [18] to the gate.
- With the gate fully closed, position the front bracket [18], respecting the measurement (L).
Make sure the front bracket [18] and rear bracket [17] are properly levelled, as shown in the
figures below, then fasten the front bracket [18] to the gate.
L
17
18

11
IP2352EN
EN
6.3 Using the positioning template
During installation, the bracket positioning operation can be greatly simplified by using the po-
sitioning template (optional accessory) which allows you to establish the correct position of the
brackets and the distance between them. This avoids positioning errors and incorrect fixing hole
alignment, thanks also to the built-in spirit-level.
The installation template is compatible with all the pistons of the PWR, Obbi and Luxo ranges.
80 60
115
90
Ø9 6
185
15 170
10
Ø14
S
17
E
18
140
20
50
10 42
120
Ø22
80 60
115
90
Ø9 6
50

12
IP2352EN
EN
6.4 Installing the gearmotor
• Open the lock window [8], loosen the screw 3,9x22mm [9] and remove the rear cover [7].
Loosen the screw M4 x 8mm [10] and take out the front cover [11] as shown in the figure.
Release the piston by inserting the key [23] in the relative lock [24] and turning it clockwise
(see the User Instructions).
• Fasten the piston to the rear bracket [17] using the screw M8x45mm [19], the bush [20] and the
washer Ø24mm [21], then tighten the self-locking nut M8 [22] as far as it will go.
• Open the gate wing manually and insert the front coupling pin [25] in the hole of the front fas-
tening bracket [18]. Lock the pin in the bracket using the washer Ø30mm [26] and nut M16 [27]
supplied. Before installing the piston, grease the rotation points.
NB: pay special attention to the correct positioning of the washer on the brackets.
• After making the adjustments (par. 6.5 and 6.6), insert the front cover [11] on the drive screw
and fix it in place using the screw [10].
NB: make sure the drive screw [25] enters the head [28] of the cover [11] correctly (detail shown
in the figure a below).
9
24
10
a
23
21
22
25
18
26
27
8
7
19
17
11
20
28

13
IP2352EN
EN
6.5 Adjusting the mechanical end stop (standard on PWR50AC)
Bring the gate wing to its fully open position. Loosen the mechanical end stop with a 5mm Allen
wrench, just enough so that it can slide along the drive screw. Move it up against the split nut and
and clamp them in place with a 5mm Allen wrench so fix the 3mm socket set screw.
6.6 Adjusting electromechanical limit switch (optional)
Bring the gate wing to its fully open or closed position. Loosen the limit switches with a Phillips
screwdriver, just enough so that they can slide along the guide, then bring them above the split
nut [14] until the sensor is activated. Fix them in place.
3mm
5mm

14
IP2352EN
EN
6.8 Electrical connections
To connect the automation to the control panel, proceed as follows:
• Remove the rear cover [7] as explained in paragraph 6.4.
• Fit the cable gland on the automation, inserting it in the relative threaded hole in the metal
fusion (Fig. 6.2 and 6.3).
• Connect the various wires as shown in the electrical diagram in Fig. 6.4.
• Fasten the rear cover [7] to the gearmotor.
The electrical connections and start-up of the PWR50AC gearmotors are explained in the instal-
lation manuals of the LOGICM / LCA80 control panels.
To increase the protection of the motor cable, a corrugated flexible tube can be used.
M
M
6.7 Reversible and irreversible piston
To make the piston reversible, insert pin [M].
NOTE: the operation must be carried out with the piston moving.
Removing the pin [M], the piston becomes irreversible, and the release can only be made with the
key (see USER MANUAL).
Fig. 6.2 Fig. 6.3

15
IP2352EN
EN
LN XZY
UWV
Gearmotor with
closure delay
V/Y U/X W/Z
Control panel
M1
Power supply
230V ~- 50/60 Hz
Gearmotor with
opening delay
V/Y U/X W/Z
M2
M1
M2
V/Y U/X W/Z
brake motor
M
6.9 Motor connection diagram
Fig. 6.4

IP2352EN
Entrematic Group AB
Lodjursgatan 10
SE-261 44, Landskrona
Sweden
www.entrematic.com
NB: for spare parts, refer to the spares price list.
8. Troubleshooting
Problem Possible cause Operation
The gate doesn't
open or close
No power supply. Make sure the mains supply is active.
Gearmotor released. See the release instructions.
Photocells occupied. Check the photocells are clean and op-
erating correctly.
Permanent STOP command. Check the STOP command or the con-
trol panel.
Faulty selector. Check the selector or control panel.
Faulty remote control. Check the condition of the batteries.
Electric lock not working. Check the lock is positioned and work-
ing correctly.
The gate opens,
but it doesn't close
Photocells occupied. Check the photocells are clean and op-
erating correctly.
i
7. Routine maintenance plan
Carry out the following operations and checks every 6 months or 36.000 cycles.
Disconnect the 230V~ power supply and batteries (if present):
- Clean and lubricate the gate rotation pins, hinges and drive screw with neutral grease.
- Check the state of wear of the brushes [12], and replace them if necessary.
- Check the resistance of the fixing points.
- Check the electrical connections are in good condition.
Reconnect the 230V~ power supply and batteries (if present):
- Check the power adjustment.
- Check all the commands and safety functions (photocells) are operating correctly.
- Check the release system is working correctly.
- If batteries are fitted, check they are working properly (in continuity) by disconnecting the pow-
er supply and performing a series of consecutive operations. At the end, reconnect the 230V~
power supply.
9. Disposal
The packaging components (cardboard, plastic, etc.) must be separated out for recycling.
Refer to the local disposal regulations before proceeding.
The packaging materials must not be discarded in the environment or left within reach of
children, as they are a potential source of danger.
To dispose of electrical and electronic equipment, batteries and accumulators correctly,
take the product to the differentiated disposal and recycling centres, respecting the regula-
tions in force