dji Inspire 1 V1.2 Operator's manual
11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. Mini-HDMI Port
18. Micro-USB Port
19. CAN-Bus Port
20. USB Port
21. Back Buttons (Reserved)
YC.BZ.S00101.02
Return to home
Vision Positioning
Altitude 2.5 m
GPS Positioning
10
4
9
9
8
4
5
6
1
3
7
2
21
17 18 19 20
11
14
13
12
1615
6
13
2
5
9
5
8
6
6
7
7
7
14
15
10
11
12
13
4
451 mm
4
3
8 m
m
301 mm
Quick Start Guide
INSPIRE 1 The Inspire 1 is a professional aerial filmmaking and photography platform that is ready to fly right out of the box. Featuring
an onboard camera equipped with a 20mm lens and 3-axis stabilized gimbal, it shoots sharp 12mp stills and stable video at
up to 4K. Its retractable landing gear pulls up out of view, giving the camera an unobstructed 360 degree view of the world
below.
An advanced flight controller makes the Inspire 1 stable, safe and easy to fly indoors or out. The brand new Vision
Positioning System gives it the power to hover in position at low altitudes even without GPS. Like all DJI flight controllers,
it is also able to return home if remote controller signal is lost or if the low battery warning is triggered.
The Inspire 1 boasts a maximum flight speed 22m/s* and a maximum flight time of 18 minutes*using one fully charged
4500mAh Intelligent Flight Battery.
The maximum transmission distance of the Inspire 1 remote controller is 2km*. The remote controller also allows you to
control the landing gear or activate Return to Home with a tap. Other buttons allow instant photo capture, video recording,
picture review and gimbal control.
A DJI Lightbridge-based HD video downlink is built-in, letting you see what your camera sees on your mobile device in
real time HD. The app also allows you to change camera settings and activate Master/Slave mode so that one person can
fly while other controls the gimbal independently. The master and slave controllers communicate using a 5.8Ghz wireless
signal, and have a communication range with each other of up to 50 meters.The controller’s LiPo battery has a maximum
run time of approximately four hours and can be charged by plugging directly into the controller.
1. Power Button
2. Transformation Switch
3. Return to Home (RTH) Button
4. Control Sticks
5. Status LED
6. Battery Level LEDs
7. Power Port
8. Mobile Device Holder
9. Antennas
10. Handle Bar
* Please note that maximum flight speed and maximum run time were tested in a lab environment. These statistics are for reference only, as
conditions in your area may vary.
* Please note that the max transmission distance were tested in a lab environment. This statistic is for reference only, as conditions in your
area may vary.
INSPIRE 1 Remote Controller
Folded
● Environmental Considerations:
1. Do not fly in severe weather conditions. This includes high wind, snow, rain and smog.
2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the onboard compass and GPS signal.
3. Avoid from obstacles, crowds, high voltage power lines, trees or bodies of water.
4. Minimize electromagnetic interference by not flying in areas with high levels of electromagnetism, including mobile
phone base stations or radio transmission towers.
5. Aircraft and battery performance is subject to environmental factors such as air density and temperature. Be very careful when
flying 14700 feet (4500 meters) or more above sea level as battery and aircraft performance may be reduced.
6.
The Inspire 1 cannot operate in P mode or use GPS at polar latitudes. It only can fly in ATTI mode and use the Vision Position-
ing System.
Fly Safe Appendix
● P Mode:
Safe to fly. In this mode, the Inspire 1 has a strong GPS signal and
can use the Vision Positioning System allowing it to hover accurately
in position indoors and out. If outdoors, this mode also means that a
Home Point has been locked so that it can Return to Home if the
control signal is lost.
There are three states in P mode.
P-GPS: GPS works best when outdoors in a wide open area, and
your Inspire 1 uses GPS to hover in place when the GPS signal is
strong. P-OPTI: If GPS is not available, the aircraft can use the
Vision Positioning System to hover accurately. P-ATTI: Neither
GPS or Vision Positioning System available, aircraft is using only
its barometer for positioning, so only altitude is controlled.
Note that the Vision Positioning System may not work properly when
the Inspire 1 is flying over water, over surfaces without a clear pattern,
or in a low light environment.
● Return to Home:
When the GPS signal is strong, the aircraft will be able to record a
Home Point and return to the Home Point when needed. The GPS
location is recorded when the GPS signal icon in the DJI Pilot app is
either yellow or green.
The aircraft will return to the Home Point automatically in the following
cases (all require a strong GPS signal).
Smart RTH: When you press the RTH button on the remote controller
or in the App. Low Battery RTH: The DJI Pilot app notifies users to take
action when the battery level falls to a specified threshold.
Failsafe RTH: When the remote controller signal is lost.
● While returning home, its altitude can be adjusted by the user to avoid obstructions. Tall buildings may affect the remote controller signal.
The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure fly higher than any nearby buildings to avoid crashing.
V1.2
If you are not in this mode, toggle the Flight
Mode Switch to P position to enable it.
The Flight Mode Switch is locked in P mode by default.
Refer to the User Manual on how to unlock the switch.
● Aircraft (Model: T600)
Weight (Battery Included) 2935 g
Maximum Weight of Payload 3400 g
Max Tilt Angle 35°
Max Ascent Speed 5 m/s
Max Descent Speed 4 m/s
Max Speed 22 m/s (ATTI mode, no wind)
Max Flight Altitude 4500 m
Max Flight Time Approximately 18 minutes
Operating Temperature Range
-10°C to 40°C
● Gimbal (Model: ZENMUSE X3)
Angular Vibration Range ±0.03°
Controllable Range Pitch: -90° to +30° Pan: ±320°
Max Controllable Speed Pitch: 120°/s Pan: 180°/s
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 5 cm-500 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
Operating Range 0-250 cm
● Camera (Name/Model: X3/FC350)
Sensor Sony EXMOR 1/2.3”Effective pixels:12.4M (total pixels: 12.76M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s-1/8000 s
Image Max Size 4000x3000
Still Photography Modes Single shoot; Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias; Time-lapse
Video Recording Modes UHD (4K): 4096x2160p 24/25, 3840x2160p 24/25/30
FHD: 1920x1080p 24/25/30/48/50/60 HD: 1280x720p 24/25/30/48/50/60
Max Bitrate Of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro SD, Max capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range
0°C to 40°C
● Remote Controller (Name: C1)
Operating Frequency 922.7 MHz-927.7 MHz (Japan only) 5.725 GHz-5.825 GHz 2.400 GHz-2.483 GHz
Transmitting Distance 2 km (outdoor and unobstructed)
Video Output Port USB, Mini-HDMI
Operating Temperature Range -10°C to 40°C
Battery 6000 mAh LiPo 2S
● Charger (Model: A14-100P1A)
Voltage 26.3 V
Rated Power 100 W
● Intelligent Flight Battery (Model: TB47, Standard)
Capacity 4500 mAh
Voltage 22.2 V
Battery Type LiPo 6S High voltage battery
Energy 99.9 Wh
Net Weight 570 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
● Intelligent Flight Battery (Model: TB48, Optional)
Capacity 5700 mAh
Voltage 22.8 V
Battery Type LiPo 6S High voltage battery
Energy 129.6 Wh
Net Weight 670 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
1
8
2
mm
1
7
2
m
m
105 mm
71 mm
● Flight Limits:
The Inspire 1 is not permitted to fly within no-fly zones as specified
by local laws and regulations. Please visit here:
http://flysafe.dji.com/no-fly for more information.
FCC ID：SS3-WM6101410 FCC ID：SS3-GL6581502
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
※ This Quick Start Guide is subject to change without prior notice.
Landing Mode
Travel Mode
Flight Mode
Landing Gear Up Landing Gear Down
1. Gimbal and Camera
2. Camera Micro-SD Card Slot
3. Vision Positioning System
4. Transformation Mechanism
5. Front LEDs
6. Motors
7. Propellers
8. Rear LEDs
9. Intelligent Flight Battery
10. Power Button
11. Battery Level Indicators
12. Aircraft Status Indicator
13. Aircraft Micro-USB Port
14. Camera Micro-USB Port
15. Gimbal Lock Connect to the
mobile device
● Calibrating the Compass:
Make sure to calibrate the compass in every new flight location. The compass is very sensitive to electromagnetic interference,
which can cause abnormal compass data leading to poor flight performance or even failure. Regular calibration is required for
optimum performance. Recalibrate the compass when: a) The Aircraft Status Indicator is blinking red and yellow. b) Flying in a
new location.
● DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking
structures, and steel reinforcements underground.
● DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
● DO NOT calibrate beside massive metal objects.
● If the Flight Status LED is showing solid red, then try to calibrate again. If it is blinking red and yellow alternately after placing
the aircraft on the ground, the compass has detected magnetic interference. Change your location.
21
11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. Mini-HDMI Port
18. Micro-USB Port
19. CAN-Bus Port
20. USB Port
21. Back Buttons (Reserved)
YC.BZ.S00101.02
Return to home
Vision Positioning
Altitude 2.5 m
GPS Positioning
10
4
9
9
8
4
5
6
1
3
7
2
21
17 18 19 20
11
14
13
12
1615
6
13
2
5
9
5
8
6
6
7
7
7
14
15
10
11
12
13
4
451 mm
4
3
8 m
m
301 mm
Quick Start Guide
INSPIRE 1 The Inspire 1 is a professional aerial filmmaking and photography platform that is ready to fly right out of the box. Featuring
an onboard camera equipped with a 20mm lens and 3-axis stabilized gimbal, it shoots sharp 12mp stills and stable video at
up to 4K. Its retractable landing gear pulls up out of view, giving the camera an unobstructed 360 degree view of the world
below.
An advanced flight controller makes the Inspire 1 stable, safe and easy to fly indoors or out. The brand new Vision
Positioning System gives it the power to hover in position at low altitudes even without GPS. Like all DJI flight controllers,
it is also able to return home if remote controller signal is lost or if the low battery warning is triggered.
The Inspire 1 boasts a maximum flight speed 22m/s* and a maximum flight time of 18 minutes*using one fully charged
4500mAh Intelligent Flight Battery.
The maximum transmission distance of the Inspire 1 remote controller is 2km*. The remote controller also allows you to
control the landing gear or activate Return to Home with a tap. Other buttons allow instant photo capture, video recording,
picture review and gimbal control.
A DJI Lightbridge-based HD video downlink is built-in, letting you see what your camera sees on your mobile device in
real time HD. The app also allows you to change camera settings and activate Master/Slave mode so that one person can
fly while other controls the gimbal independently. The master and slave controllers communicate using a 5.8Ghz wireless
signal, and have a communication range with each other of up to 50 meters.The controller’s LiPo battery has a maximum
run time of approximately four hours and can be charged by plugging directly into the controller.
1. Power Button
2. Transformation Switch
3. Return to Home (RTH) Button
4. Control Sticks
5. Status LED
6. Battery Level LEDs
7. Power Port
8. Mobile Device Holder
9. Antennas
10. Handle Bar
* Please note that maximum flight speed and maximum run time were tested in a lab environment. These statistics are for reference only, as
conditions in your area may vary.
* Please note that the max transmission distance were tested in a lab environment. This statistic is for reference only, as conditions in your
area may vary.
INSPIRE 1 Remote Controller
Folded
● Environmental Considerations:
1. Do not fly in severe weather conditions. This includes high wind, snow, rain and smog.
2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the onboard compass and GPS signal.
3. Avoid from obstacles, crowds, high voltage power lines, trees or bodies of water.
4. Minimize electromagnetic interference by not flying in areas with high levels of electromagnetism, including mobile
phone base stations or radio transmission towers.
5. Aircraft and battery performance is subject to environmental factors such as air density and temperature. Be very careful when
flying 14700 feet (4500 meters) or more above sea level as battery and aircraft performance may be reduced.
6.
The Inspire 1 cannot operate in P mode or use GPS at polar latitudes. It only can fly in ATTI mode and use the Vision Position-
ing System.
Fly Safe Appendix
● P Mode:
Safe to fly. In this mode, the Inspire 1 has a strong GPS signal and
can use the Vision Positioning System allowing it to hover accurately
in position indoors and out. If outdoors, this mode also means that a
Home Point has been locked so that it can Return to Home if the
control signal is lost.
There are three states in P mode.
P-GPS: GPS works best when outdoors in a wide open area, and
your Inspire 1 uses GPS to hover in place when the GPS signal is
strong. P-OPTI: If GPS is not available, the aircraft can use the
Vision Positioning System to hover accurately. P-ATTI: Neither
GPS or Vision Positioning System available, aircraft is using only
its barometer for positioning, so only altitude is controlled.
Note that the Vision Positioning System may not work properly when
the Inspire 1 is flying over water, over surfaces without a clear pattern,
or in a low light environment.
● Return to Home:
When the GPS signal is strong, the aircraft will be able to record a
Home Point and return to the Home Point when needed. The GPS
location is recorded when the GPS signal icon in the DJI Pilot app is
either yellow or green.
The aircraft will return to the Home Point automatically in the following
cases (all require a strong GPS signal).
Smart RTH: When you press the RTH button on the remote controller
or in the App. Low Battery RTH: The DJI Pilot app notifies users to take
action when the battery level falls to a specified threshold.
Failsafe RTH: When the remote controller signal is lost.
● While returning home, its altitude can be adjusted by the user to avoid obstructions. Tall buildings may affect the remote controller signal.
The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure fly higher than any nearby buildings to avoid crashing.
V1.2
If you are not in this mode, toggle the Flight
Mode Switch to P position to enable it.
The Flight Mode Switch is locked in P mode by default.
Refer to the User Manual on how to unlock the switch.
● Aircraft (Model: T600)
Weight (Battery Included) 2935 g
Maximum Weight of Payload 3400 g
Max Tilt Angle 35°
Max Ascent Speed 5 m/s
Max Descent Speed 4 m/s
Max Speed 22 m/s (ATTI mode, no wind)
Max Flight Altitude 4500 m
Max Flight Time Approximately 18 minutes
Operating Temperature Range
-10°C to 40°C
● Gimbal (Model: ZENMUSE X3)
Angular Vibration Range ±0.03°
Controllable Range Pitch: -90° to +30° Pan: ±320°
Max Controllable Speed Pitch: 120°/s Pan: 180°/s
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 5 cm-500 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
Operating Range 0-250 cm
● Camera (Name/Model: X3/FC350)
Sensor Sony EXMOR 1/2.3”Effective pixels:12.4M (total pixels: 12.76M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s-1/8000 s
Image Max Size 4000x3000
Still Photography Modes Single shoot; Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias; Time-lapse
Video Recording Modes UHD (4K): 4096x2160p 24/25, 3840x2160p 24/25/30
FHD: 1920x1080p 24/25/30/48/50/60 HD: 1280x720p 24/25/30/48/50/60
Max Bitrate Of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro SD, Max capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range
0°C to 40°C
● Remote Controller (Name: C1)
Operating Frequency 922.7 MHz-927.7 MHz (Japan only) 5.725 GHz-5.825 GHz 2.400 GHz-2.483 GHz
Transmitting Distance 2 km (outdoor and unobstructed)
Video Output Port USB, Mini-HDMI
Operating Temperature Range -10°C to 40°C
Battery 6000 mAh LiPo 2S
● Charger (Model: A14-100P1A)
Voltage 26.3 V
Rated Power 100 W
● Intelligent Flight Battery (Model: TB47, Standard)
Capacity 4500 mAh
Voltage 22.2 V
Battery Type LiPo 6S High voltage battery
Energy 99.9 Wh
Net Weight 570 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
● Intelligent Flight Battery (Model: TB48, Optional)
Capacity 5700 mAh
Voltage 22.8 V
Battery Type LiPo 6S High voltage battery
Energy 129.6 Wh
Net Weight 670 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
1
8
2
mm
1
7
2
m
m
105 mm
71 mm
● Flight Limits:
The Inspire 1 is not permitted to fly within no-fly zones as specified
by local laws and regulations. Please visit here:
http://flysafe.dji.com/no-fly for more information.
FCC ID：SS3-WM6101410 FCC ID：SS3-GL6581502
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
※ This Quick Start Guide is subject to change without prior notice.
Landing Mode
Travel Mode
Flight Mode
Landing Gear Up Landing Gear Down
1. Gimbal and Camera
2. Camera Micro-SD Card Slot
3. Vision Positioning System
4. Transformation Mechanism
5. Front LEDs
6. Motors
7. Propellers
8. Rear LEDs
9. Intelligent Flight Battery
10. Power Button
11. Battery Level Indicators
12. Aircraft Status Indicator
13. Aircraft Micro-USB Port
14. Camera Micro-USB Port
15. Gimbal Lock Connect to the
mobile device
● Calibrating the Compass:
Make sure to calibrate the compass in every new flight location. The compass is very sensitive to electromagnetic interference,
which can cause abnormal compass data leading to poor flight performance or even failure. Regular calibration is required for
optimum performance. Recalibrate the compass when: a) The Aircraft Status Indicator is blinking red and yellow. b) Flying in a
new location.
● DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking
structures, and steel reinforcements underground.
● DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
● DO NOT calibrate beside massive metal objects.
● If the Flight Status LED is showing solid red, then try to calibrate again. If it is blinking red and yellow alternately after placing
the aircraft on the ground, the compass has detected magnetic interference. Change your location.
21
11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. Mini-HDMI Port
18. Micro-USB Port
19. CAN-Bus Port
20. USB Port
21. Back Buttons (Reserved)
YC.BZ.S00101.02
Return to home
Vision Positioning
Altitude 2.5 m
GPS Positioning
10
4
9
9
8
4
5
6
1
3
7
2
21
17 18 19 20
11
14
13
12
1615
6
13
2
5
9
5
8
6
6
7
7
7
14
15
10
11
12
13
4
451 mm
4
3
8 m
m
301 mm
Quick Start Guide
INSPIRE 1 The Inspire 1 is a professional aerial filmmaking and photography platform that is ready to fly right out of the box. Featuring
an onboard camera equipped with a 20mm lens and 3-axis stabilized gimbal, it shoots sharp 12mp stills and stable video at
up to 4K. Its retractable landing gear pulls up out of view, giving the camera an unobstructed 360 degree view of the world
below.
An advanced flight controller makes the Inspire 1 stable, safe and easy to fly indoors or out. The brand new Vision
Positioning System gives it the power to hover in position at low altitudes even without GPS. Like all DJI flight controllers,
it is also able to return home if remote controller signal is lost or if the low battery warning is triggered.
The Inspire 1 boasts a maximum flight speed 22m/s* and a maximum flight time of 18 minutes*using one fully charged
4500mAh Intelligent Flight Battery.
The maximum transmission distance of the Inspire 1 remote controller is 2km*. The remote controller also allows you to
control the landing gear or activate Return to Home with a tap. Other buttons allow instant photo capture, video recording,
picture review and gimbal control.
A DJI Lightbridge-based HD video downlink is built-in, letting you see what your camera sees on your mobile device in
real time HD. The app also allows you to change camera settings and activate Master/Slave mode so that one person can
fly while other controls the gimbal independently. The master and slave controllers communicate using a 5.8Ghz wireless
signal, and have a communication range with each other of up to 50 meters.The controller’s LiPo battery has a maximum
run time of approximately four hours and can be charged by plugging directly into the controller.
1. Power Button
2. Transformation Switch
3. Return to Home (RTH) Button
4. Control Sticks
5. Status LED
6. Battery Level LEDs
7. Power Port
8. Mobile Device Holder
9. Antennas
10. Handle Bar
* Please note that maximum flight speed and maximum run time were tested in a lab environment. These statistics are for reference only, as
conditions in your area may vary.
* Please note that the max transmission distance were tested in a lab environment. This statistic is for reference only, as conditions in your
area may vary.
INSPIRE 1 Remote Controller
Folded
● Environmental Considerations:
1. Do not fly in severe weather conditions. This includes high wind, snow, rain and smog.
2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the onboard compass and GPS signal.
3. Avoid from obstacles, crowds, high voltage power lines, trees or bodies of water.
4. Minimize electromagnetic interference by not flying in areas with high levels of electromagnetism, including mobile
phone base stations or radio transmission towers.
5. Aircraft and battery performance is subject to environmental factors such as air density and temperature. Be very careful when
flying 14700 feet (4500 meters) or more above sea level as battery and aircraft performance may be reduced.
6.
The Inspire 1 cannot operate in P mode or use GPS at polar latitudes. It only can fly in ATTI mode and use the Vision Position-
ing System.
Fly Safe Appendix
● P Mode:
Safe to fly. In this mode, the Inspire 1 has a strong GPS signal and
can use the Vision Positioning System allowing it to hover accurately
in position indoors and out. If outdoors, this mode also means that a
Home Point has been locked so that it can Return to Home if the
control signal is lost.
There are three states in P mode.
P-GPS: GPS works best when outdoors in a wide open area, and
your Inspire 1 uses GPS to hover in place when the GPS signal is
strong. P-OPTI: If GPS is not available, the aircraft can use the
Vision Positioning System to hover accurately. P-ATTI: Neither
GPS or Vision Positioning System available, aircraft is using only
its barometer for positioning, so only altitude is controlled.
Note that the Vision Positioning System may not work properly when
the Inspire 1 is flying over water, over surfaces without a clear pattern,
or in a low light environment.
● Return to Home:
When the GPS signal is strong, the aircraft will be able to record a
Home Point and return to the Home Point when needed. The GPS
location is recorded when the GPS signal icon in the DJI Pilot app is
either yellow or green.
The aircraft will return to the Home Point automatically in the following
cases (all require a strong GPS signal).
Smart RTH: When you press the RTH button on the remote controller
or in the App. Low Battery RTH: The DJI Pilot app notifies users to take
action when the battery level falls to a specified threshold.
Failsafe RTH: When the remote controller signal is lost.
● While returning home, its altitude can be adjusted by the user to avoid obstructions. Tall buildings may affect the remote controller signal.
The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure fly higher than any nearby buildings to avoid crashing.
V1.2
If you are not in this mode, toggle the Flight
Mode Switch to P position to enable it.
The Flight Mode Switch is locked in P mode by default.
Refer to the User Manual on how to unlock the switch.
● Aircraft (Model: T600)
Weight (Battery Included) 2935 g
Maximum Weight of Payload 3400 g
Max Tilt Angle 35°
Max Ascent Speed 5 m/s
Max Descent Speed 4 m/s
Max Speed 22 m/s (ATTI mode, no wind)
Max Flight Altitude 4500 m
Max Flight Time Approximately 18 minutes
Operating Temperature Range
-10°C to 40°C
● Gimbal (Model: ZENMUSE X3)
Angular Vibration Range ±0.03°
Controllable Range Pitch: -90° to +30° Pan: ±320°
Max Controllable Speed Pitch: 120°/s Pan: 180°/s
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 5 cm-500 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
Operating Range 0-250 cm
● Camera (Name/Model: X3/FC350)
Sensor Sony EXMOR 1/2.3”Effective pixels:12.4M (total pixels: 12.76M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s-1/8000 s
Image Max Size 4000x3000
Still Photography Modes Single shoot; Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias; Time-lapse
Video Recording Modes UHD (4K): 4096x2160p 24/25, 3840x2160p 24/25/30
FHD: 1920x1080p 24/25/30/48/50/60 HD: 1280x720p 24/25/30/48/50/60
Max Bitrate Of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro SD, Max capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range
0°C to 40°C
● Remote Controller (Name: C1)
Operating Frequency 922.7 MHz-927.7 MHz (Japan only) 5.725 GHz-5.825 GHz 2.400 GHz-2.483 GHz
Transmitting Distance 2 km (outdoor and unobstructed)
Video Output Port USB, Mini-HDMI
Operating Temperature Range -10°C to 40°C
Battery 6000 mAh LiPo 2S
● Charger (Model: A14-100P1A)
Voltage 26.3 V
Rated Power 100 W
● Intelligent Flight Battery (Model: TB47, Standard)
Capacity 4500 mAh
Voltage 22.2 V
Battery Type LiPo 6S High voltage battery
Energy 99.9 Wh
Net Weight 570 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
● Intelligent Flight Battery (Model: TB48, Optional)
Capacity 5700 mAh
Voltage 22.8 V
Battery Type LiPo 6S High voltage battery
Energy 129.6 Wh
Net Weight 670 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
1
8
2
mm
1
7
2
m
m
105 mm
71 mm
● Flight Limits:
The Inspire 1 is not permitted to fly within no-fly zones as specified
by local laws and regulations. Please visit here:
http://flysafe.dji.com/no-fly for more information.
FCC ID：SS3-WM6101410 FCC ID：SS3-GL6581502
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
※ This Quick Start Guide is subject to change without prior notice.
Landing Mode
Travel Mode
Flight Mode
Landing Gear Up Landing Gear Down
1. Gimbal and Camera
2. Camera Micro-SD Card Slot
3. Vision Positioning System
4. Transformation Mechanism
5. Front LEDs
6. Motors
7. Propellers
8. Rear LEDs
9. Intelligent Flight Battery
10. Power Button
11. Battery Level Indicators
12. Aircraft Status Indicator
13. Aircraft Micro-USB Port
14. Camera Micro-USB Port
15. Gimbal Lock Connect to the
mobile device
● Calibrating the Compass:
Make sure to calibrate the compass in every new flight location. The compass is very sensitive to electromagnetic interference,
which can cause abnormal compass data leading to poor flight performance or even failure. Regular calibration is required for
optimum performance. Recalibrate the compass when: a) The Aircraft Status Indicator is blinking red and yellow. b) Flying in a
new location.
● DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking
structures, and steel reinforcements underground.
● DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
● DO NOT calibrate beside massive metal objects.
● If the Flight Status LED is showing solid red, then try to calibrate again. If it is blinking red and yellow alternately after placing
the aircraft on the ground, the compass has detected magnetic interference. Change your location.
21
11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. Mini-HDMI Port
18. Micro-USB Port
19. CAN-Bus Port
20. USB Port
21. Back Buttons (Reserved)
YC.BZ.S00101.02
Return to home
Vision Positioning
Altitude 2.5 m
GPS Positioning
10
4
9
9
8
4
5
6
1
3
7
2
21
17 18 19 20
11
14
13
12
1615
6
13
2
5
9
5
8
6
6
7
7
7
14
15
10
11
12
13
4
451 mm
4
3
8 m
m
301 mm
Quick Start Guide
INSPIRE 1 The Inspire 1 is a professional aerial filmmaking and photography platform that is ready to fly right out of the box. Featuring
an onboard camera equipped with a 20mm lens and 3-axis stabilized gimbal, it shoots sharp 12mp stills and stable video at
up to 4K. Its retractable landing gear pulls up out of view, giving the camera an unobstructed 360 degree view of the world
below.
An advanced flight controller makes the Inspire 1 stable, safe and easy to fly indoors or out. The brand new Vision
Positioning System gives it the power to hover in position at low altitudes even without GPS. Like all DJI flight controllers,
it is also able to return home if remote controller signal is lost or if the low battery warning is triggered.
The Inspire 1 boasts a maximum flight speed 22m/s* and a maximum flight time of 18 minutes*using one fully charged
4500mAh Intelligent Flight Battery.
The maximum transmission distance of the Inspire 1 remote controller is 2km*. The remote controller also allows you to
control the landing gear or activate Return to Home with a tap. Other buttons allow instant photo capture, video recording,
picture review and gimbal control.
A DJI Lightbridge-based HD video downlink is built-in, letting you see what your camera sees on your mobile device in
real time HD. The app also allows you to change camera settings and activate Master/Slave mode so that one person can
fly while other controls the gimbal independently. The master and slave controllers communicate using a 5.8Ghz wireless
signal, and have a communication range with each other of up to 50 meters.The controller’s LiPo battery has a maximum
run time of approximately four hours and can be charged by plugging directly into the controller.
1. Power Button
2. Transformation Switch
3. Return to Home (RTH) Button
4. Control Sticks
5. Status LED
6. Battery Level LEDs
7. Power Port
8. Mobile Device Holder
9. Antennas
10. Handle Bar
* Please note that maximum flight speed and maximum run time were tested in a lab environment. These statistics are for reference only, as
conditions in your area may vary.
* Please note that the max transmission distance were tested in a lab environment. This statistic is for reference only, as conditions in your
area may vary.
INSPIRE 1 Remote Controller
Folded
● Environmental Considerations:
1. Do not fly in severe weather conditions. This includes high wind, snow, rain and smog.
2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the onboard compass and GPS signal.
3. Avoid from obstacles, crowds, high voltage power lines, trees or bodies of water.
4. Minimize electromagnetic interference by not flying in areas with high levels of electromagnetism, including mobile
phone base stations or radio transmission towers.
5. Aircraft and battery performance is subject to environmental factors such as air density and temperature. Be very careful when
flying 14700 feet (4500 meters) or more above sea level as battery and aircraft performance may be reduced.
6.
The Inspire 1 cannot operate in P mode or use GPS at polar latitudes. It only can fly in ATTI mode and use the Vision Position-
ing System.
Fly Safe Appendix
● P Mode:
Safe to fly. In this mode, the Inspire 1 has a strong GPS signal and
can use the Vision Positioning System allowing it to hover accurately
in position indoors and out. If outdoors, this mode also means that a
Home Point has been locked so that it can Return to Home if the
control signal is lost.
There are three states in P mode.
P-GPS: GPS works best when outdoors in a wide open area, and
your Inspire 1 uses GPS to hover in place when the GPS signal is
strong. P-OPTI: If GPS is not available, the aircraft can use the
Vision Positioning System to hover accurately. P-ATTI: Neither
GPS or Vision Positioning System available, aircraft is using only
its barometer for positioning, so only altitude is controlled.
Note that the Vision Positioning System may not work properly when
the Inspire 1 is flying over water, over surfaces without a clear pattern,
or in a low light environment.
● Return to Home:
When the GPS signal is strong, the aircraft will be able to record a
Home Point and return to the Home Point when needed. The GPS
location is recorded when the GPS signal icon in the DJI Pilot app is
either yellow or green.
The aircraft will return to the Home Point automatically in the following
cases (all require a strong GPS signal).
Smart RTH: When you press the RTH button on the remote controller
or in the App. Low Battery RTH: The DJI Pilot app notifies users to take
action when the battery level falls to a specified threshold.
Failsafe RTH: When the remote controller signal is lost.
● While returning home, its altitude can be adjusted by the user to avoid obstructions. Tall buildings may affect the remote controller signal.
The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure fly higher than any nearby buildings to avoid crashing.
V1.2
If you are not in this mode, toggle the Flight
Mode Switch to P position to enable it.
The Flight Mode Switch is locked in P mode by default.
Refer to the User Manual on how to unlock the switch.
● Aircraft (Model: T600)
Weight (Battery Included) 2935 g
Maximum Weight of Payload 3400 g
Max Tilt Angle 35°
Max Ascent Speed 5 m/s
Max Descent Speed 4 m/s
Max Speed 22 m/s (ATTI mode, no wind)
Max Flight Altitude 4500 m
Max Flight Time Approximately 18 minutes
Operating Temperature Range
-10°C to 40°C
● Gimbal (Model: ZENMUSE X3)
Angular Vibration Range ±0.03°
Controllable Range Pitch: -90° to +30° Pan: ±320°
Max Controllable Speed Pitch: 120°/s Pan: 180°/s
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 5 cm-500 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
Operating Range 0-250 cm
● Camera (Name/Model: X3/FC350)
Sensor Sony EXMOR 1/2.3”Effective pixels:12.4M (total pixels: 12.76M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s-1/8000 s
Image Max Size 4000x3000
Still Photography Modes Single shoot; Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias; Time-lapse
Video Recording Modes UHD (4K): 4096x2160p 24/25, 3840x2160p 24/25/30
FHD: 1920x1080p 24/25/30/48/50/60 HD: 1280x720p 24/25/30/48/50/60
Max Bitrate Of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro SD, Max capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range
0°C to 40°C
● Remote Controller (Name: C1)
Operating Frequency 922.7 MHz-927.7 MHz (Japan only) 5.725 GHz-5.825 GHz 2.400 GHz-2.483 GHz
Transmitting Distance 2 km (outdoor and unobstructed)
Video Output Port USB, Mini-HDMI
Operating Temperature Range -10°C to 40°C
Battery 6000 mAh LiPo 2S
● Charger (Model: A14-100P1A)
Voltage 26.3 V
Rated Power 100 W
● Intelligent Flight Battery (Model: TB47, Standard)
Capacity 4500 mAh
Voltage 22.2 V
Battery Type LiPo 6S High voltage battery
Energy 99.9 Wh
Net Weight 570 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
● Intelligent Flight Battery (Model: TB48, Optional)
Capacity 5700 mAh
Voltage 22.8 V
Battery Type LiPo 6S High voltage battery
Energy 129.6 Wh
Net Weight 670 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
1
8
2
mm
1
7
2
m
m
105 mm
71 mm
● Flight Limits:
The Inspire 1 is not permitted to fly within no-fly zones as specified
by local laws and regulations. Please visit here:
http://flysafe.dji.com/no-fly for more information.
FCC ID：SS3-WM6101410 FCC ID：SS3-GL6581502
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
※ This Quick Start Guide is subject to change without prior notice.
Landing Mode
Travel Mode
Flight Mode
Landing Gear Up Landing Gear Down
1. Gimbal and Camera
2. Camera Micro-SD Card Slot
3. Vision Positioning System
4. Transformation Mechanism
5. Front LEDs
6. Motors
7. Propellers
8. Rear LEDs
9. Intelligent Flight Battery
10. Power Button
11. Battery Level Indicators
12. Aircraft Status Indicator
13. Aircraft Micro-USB Port
14. Camera Micro-USB Port
15. Gimbal Lock Connect to the
mobile device
● Calibrating the Compass:
Make sure to calibrate the compass in every new flight location. The compass is very sensitive to electromagnetic interference,
which can cause abnormal compass data leading to poor flight performance or even failure. Regular calibration is required for
optimum performance. Recalibrate the compass when: a) The Aircraft Status Indicator is blinking red and yellow. b) Flying in a
new location.
● DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking
structures, and steel reinforcements underground.
● DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
● DO NOT calibrate beside massive metal objects.
● If the Flight Status LED is showing solid red, then try to calibrate again. If it is blinking red and yellow alternately after placing
the aircraft on the ground, the compass has detected magnetic interference. Change your location.
21
11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. Mini-HDMI Port
18. Micro-USB Port
19. CAN-Bus Port
20. USB Port
21. Back Buttons (Reserved)
YC.BZ.S00101.02
Return to home
Vision Positioning
Altitude 2.5 m
GPS Positioning
10
4
9
9
8
4
5
6
1
3
7
2
21
17 18 19 20
11
14
13
12
1615
6
13
2
5
9
5
8
6
6
7
7
7
14
15
10
11
12
13
4
451 mm
4
3
8 m
m
301 mm
Quick Start Guide
INSPIRE 1 The Inspire 1 is a professional aerial filmmaking and photography platform that is ready to fly right out of the box. Featuring
an onboard camera equipped with a 20mm lens and 3-axis stabilized gimbal, it shoots sharp 12mp stills and stable video at
up to 4K. Its retractable landing gear pulls up out of view, giving the camera an unobstructed 360 degree view of the world
below.
An advanced flight controller makes the Inspire 1 stable, safe and easy to fly indoors or out. The brand new Vision
Positioning System gives it the power to hover in position at low altitudes even without GPS. Like all DJI flight controllers,
it is also able to return home if remote controller signal is lost or if the low battery warning is triggered.
The Inspire 1 boasts a maximum flight speed 22m/s* and a maximum flight time of 18 minutes*using one fully charged
4500mAh Intelligent Flight Battery.
The maximum transmission distance of the Inspire 1 remote controller is 2km*. The remote controller also allows you to
control the landing gear or activate Return to Home with a tap. Other buttons allow instant photo capture, video recording,
picture review and gimbal control.
A DJI Lightbridge-based HD video downlink is built-in, letting you see what your camera sees on your mobile device in
real time HD. The app also allows you to change camera settings and activate Master/Slave mode so that one person can
fly while other controls the gimbal independently. The master and slave controllers communicate using a 5.8Ghz wireless
signal, and have a communication range with each other of up to 50 meters.The controller’s LiPo battery has a maximum
run time of approximately four hours and can be charged by plugging directly into the controller.
1. Power Button
2. Transformation Switch
3. Return to Home (RTH) Button
4. Control Sticks
5. Status LED
6. Battery Level LEDs
7. Power Port
8. Mobile Device Holder
9. Antennas
10. Handle Bar
* Please note that maximum flight speed and maximum run time were tested in a lab environment. These statistics are for reference only, as
conditions in your area may vary.
* Please note that the max transmission distance were tested in a lab environment. This statistic is for reference only, as conditions in your
area may vary.
INSPIRE 1 Remote Controller
Folded
● Environmental Considerations:
1. Do not fly in severe weather conditions. This includes high wind, snow, rain and smog.
2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the onboard compass and GPS signal.
3. Avoid from obstacles, crowds, high voltage power lines, trees or bodies of water.
4. Minimize electromagnetic interference by not flying in areas with high levels of electromagnetism, including mobile
phone base stations or radio transmission towers.
5. Aircraft and battery performance is subject to environmental factors such as air density and temperature. Be very careful when
flying 14700 feet (4500 meters) or more above sea level as battery and aircraft performance may be reduced.
6.
The Inspire 1 cannot operate in P mode or use GPS at polar latitudes. It only can fly in ATTI mode and use the Vision Position-
ing System.
Fly Safe Appendix
● P Mode:
Safe to fly. In this mode, the Inspire 1 has a strong GPS signal and
can use the Vision Positioning System allowing it to hover accurately
in position indoors and out. If outdoors, this mode also means that a
Home Point has been locked so that it can Return to Home if the
control signal is lost.
There are three states in P mode.
P-GPS: GPS works best when outdoors in a wide open area, and
your Inspire 1 uses GPS to hover in place when the GPS signal is
strong. P-OPTI: If GPS is not available, the aircraft can use the
Vision Positioning System to hover accurately. P-ATTI: Neither
GPS or Vision Positioning System available, aircraft is using only
its barometer for positioning, so only altitude is controlled.
Note that the Vision Positioning System may not work properly when
the Inspire 1 is flying over water, over surfaces without a clear pattern,
or in a low light environment.
● Return to Home:
When the GPS signal is strong, the aircraft will be able to record a
Home Point and return to the Home Point when needed. The GPS
location is recorded when the GPS signal icon in the DJI Pilot app is
either yellow or green.
The aircraft will return to the Home Point automatically in the following
cases (all require a strong GPS signal).
Smart RTH: When you press the RTH button on the remote controller
or in the App. Low Battery RTH: The DJI Pilot app notifies users to take
action when the battery level falls to a specified threshold.
Failsafe RTH: When the remote controller signal is lost.
● While returning home, its altitude can be adjusted by the user to avoid obstructions. Tall buildings may affect the remote controller signal.
The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure fly higher than any nearby buildings to avoid crashing.
V1.2
If you are not in this mode, toggle the Flight
Mode Switch to P position to enable it.
The Flight Mode Switch is locked in P mode by default.
Refer to the User Manual on how to unlock the switch.
● Aircraft (Model: T600)
Weight (Battery Included) 2935 g
Maximum Weight of Payload 3400 g
Max Tilt Angle 35°
Max Ascent Speed 5 m/s
Max Descent Speed 4 m/s
Max Speed 22 m/s (ATTI mode, no wind)
Max Flight Altitude 4500 m
Max Flight Time Approximately 18 minutes
Operating Temperature Range
-10°C to 40°C
● Gimbal (Model: ZENMUSE X3)
Angular Vibration Range ±0.03°
Controllable Range Pitch: -90° to +30° Pan: ±320°
Max Controllable Speed Pitch: 120°/s Pan: 180°/s
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 5 cm-500 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
Operating Range 0-250 cm
● Camera (Name/Model: X3/FC350)
Sensor Sony EXMOR 1/2.3”Effective pixels:12.4M (total pixels: 12.76M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s-1/8000 s
Image Max Size 4000x3000
Still Photography Modes Single shoot; Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias; Time-lapse
Video Recording Modes UHD (4K): 4096x2160p 24/25, 3840x2160p 24/25/30
FHD: 1920x1080p 24/25/30/48/50/60 HD: 1280x720p 24/25/30/48/50/60
Max Bitrate Of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro SD, Max capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range
0°C to 40°C
● Remote Controller (Name: C1)
Operating Frequency 922.7 MHz-927.7 MHz (Japan only) 5.725 GHz-5.825 GHz 2.400 GHz-2.483 GHz
Transmitting Distance 2 km (outdoor and unobstructed)
Video Output Port USB, Mini-HDMI
Operating Temperature Range -10°C to 40°C
Battery 6000 mAh LiPo 2S
● Charger (Model: A14-100P1A)
Voltage 26.3 V
Rated Power 100 W
● Intelligent Flight Battery (Model: TB47, Standard)
Capacity 4500 mAh
Voltage 22.2 V
Battery Type LiPo 6S High voltage battery
Energy 99.9 Wh
Net Weight 570 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
● Intelligent Flight Battery (Model: TB48, Optional)
Capacity 5700 mAh
Voltage 22.8 V
Battery Type LiPo 6S High voltage battery
Energy 129.6 Wh
Net Weight 670 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
1
8
2
mm
1
7
2
m
m
105 mm
71 mm
● Flight Limits:
The Inspire 1 is not permitted to fly within no-fly zones as specified
by local laws and regulations. Please visit here:
http://flysafe.dji.com/no-fly for more information.
FCC ID：SS3-WM6101410 FCC ID：SS3-GL6581502
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
※ This Quick Start Guide is subject to change without prior notice.
Landing Mode
Travel Mode
Flight Mode
Landing Gear Up Landing Gear Down
1. Gimbal and Camera
2. Camera Micro-SD Card Slot
3. Vision Positioning System
4. Transformation Mechanism
5. Front LEDs
6. Motors
7. Propellers
8. Rear LEDs
9. Intelligent Flight Battery
10. Power Button
11. Battery Level Indicators
12. Aircraft Status Indicator
13. Aircraft Micro-USB Port
14. Camera Micro-USB Port
15. Gimbal Lock Connect to the
mobile device
● Calibrating the Compass:
Make sure to calibrate the compass in every new flight location. The compass is very sensitive to electromagnetic interference,
which can cause abnormal compass data leading to poor flight performance or even failure. Regular calibration is required for
optimum performance. Recalibrate the compass when: a) The Aircraft Status Indicator is blinking red and yellow. b) Flying in a
new location.
● DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking
structures, and steel reinforcements underground.
● DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
● DO NOT calibrate beside massive metal objects.
● If the Flight Status LED is showing solid red, then try to calibrate again. If it is blinking red and yellow alternately after placing
the aircraft on the ground, the compass has detected magnetic interference. Change your location.
21
Left stick / Up (Slowly)
Start / Stop the motors
OR
8
1
The App’s
RTH Button
● If you have purchased the dual remote controller version, you must use the Master remote controller to deactivate Travel Mode.
3
6. Preparing the Aircraft
The aircraft is in Travel Mode during delivery. Follow these steps to change it
to Landing Mode before your first flight:
Insert the Intelligent Flight Battery into the battery compartment.
Power on the remote controller and the Intelligent Flight Battery.
Toggle the Transformation Switch up and down at least four times. Repeat
to change aircraft to Travel Mode.
Power off the aircraft before mounting the gimbal and camera.
Travel Mode
Landing Mode
2
1
5. Preparing the Remote Controller
Tilt the Mobile Device Holder to the desired position then adjust
the antennas as shown. The strength of the remote controller
signal is different when the antenna position is different.
The transmission signal between the aircraft and remote
controller will perform best when within the optimal
transmission range. If the signal is weak, fly the aircraft
closer to you to achieve optimal signal performance.
1
3
2
Strong Weak
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
Left Stick Right Stick
1
5
6
7
8
1
2
56
34
7
Gimbal Cover
Gimbal Connector
Mounting Place
Gimbal Lock
Locked
2
3
1
High
B
A
A
● While returning home, its
altitude can be adjusted by the
user to avoid obstructions.
Before taking off, make sure the aircraft
status bar in the DJI Pilot app shows “Safe
to Fly (GPS)”. Otherwise, the aircraft cannot
hover in place and record the Home Point.
10. Flight
● Manual Take - off & Landing：
Safe to Fly (GPS) ● Auto Taking - Off & Landing:
Tap and confirm your selection. The aircraft will automatically take off, retract
its landing gear, and hover at 1.5 meters after you tap and confirm Auto Take-off.
1
4. Charging
Using INSPIRE 1
● You can set the remote controller to different modes using the DJI Pilot app.
● Do not use other 2.4GHz devices at the same time to avoid signal interference.
1. Download the DJI Pilot App
Visit http://m.dji.net/djipilot or scan this QR code to
download the DJI Pilot app through your mobile device.
7. Mounting the Gimbal and Camera
3. Check Battery Levels
Press the Power Button once on both the Intelligent Flight Battery and remote controller to check battery levels. The
Intelligent Flight Battery must be fully charged before using it for the first time. Make sure both batteries are adequately
charged before each flight.
Press the power button once then press again and hold for 2 seconds to power on the remote controller. Repeat to power off.
Press the power button once, then press again and hold for 2 seconds to power on the Intelligent Flight Battery. Repeat to
power off.
9. Remote Controller Operation
The remote controller is by default set to Mode 2 ( throttle controlled by the left-hand stick ).
Adjust the tilt angle of camera by using the Gimbal Dial.
● For the best user experience, please use mobile devices with iOS 8.0 (or higher) and Android 4.1.2 (or higher).
● Read the Inspire 1 User Manual in the DJI Pilot app or official DJI website for more details.
●When not in P mode, the Inspire 1 will only maintain altitude, not position, and will drift with
wind or user inputs. Return to Home is not available in F mode.
●Only use the official DJI Inspire 1 charger for your Intelligent Flight Battery and remote controller.
● To charge the Inspire 1 Intelligent Flight Battery or the remote controller, connect it to power through the port to a
suitable power source (100-240V 50/60Hz).
● It is recommended to turn off the batteries before charging.
● Use the included charger to charge the Intelligent Flight Battery and the remote controller battery. When fully charged, the
battery LEDs on the Intelligent Flight Battery and remote controller will turn off.
Watch the tutorial videos at www.dji.com or in
the DJI Pilot app.
2. Watch the Tutorial Videos
The tutorial videos
Press the button on the side of the Mobile
Device Holder to release the clamp.
Place your device onto the clamp and adjust
the clamp to hold it securely.
Connect your mobile device to the remote
controller with a USB cable. Plug one end of
the cable into your mobile device, and the
other end into the USB port on the back of
the remote controller.
Remove the Gimbal Cover.
Rotate the Gimbal Lock to the unlocked position (to the right when
facing the nose of the aircraft). Insert the gimbal by aligning the
white mark on the gimbal with white mark on the Gimbal Lock.
Rotate the gimbal lock back into the locked position (to the left
when facing the nose of the aircraft).
1
Move the Flight Mode Switch to the right to select P mode. ( P mode is Positioning mode, A mode
is ATTI mode, and the F mode is Function mode. )
Power on the remote controller.
Power on the aircraft and wait for the self-check to complete. Do not move the aircraft during the
self-check.
Ensure the remote controller is linked to the aircraft before flight. Re-link the remote controller to the
aircraft if it fails to connect. Refer to the INSPIRE 1 User Manual on how to link.
Ensure the remote controller and your mobile device are connected with a USB cable. Launch the
DJI Pilot app when connecting to the aircraft for the first time, and follow the instructions within the app.
Launch the DJI Pilot app and tap “Camera”. Ensure the aircraft is functioning normally by
completing the Checklist.Beginner Mode is enabled by default when you launch the DJI Pilot app
for the first time. The aircraft’s altitude and flight distance is restricted when flying in Beginner Mode.
We recommend you fly in Beginner Mode when using the aircraft for the first time. You may disable
Beginner Mode in the settings page of the DJI Pilot app.
Calibrate the compass by tapping the Aircraft Status Bar in the app and selecting “Calibrate”. Then
follow the on-screen instructions.
For 1345s Propeller, install the propellers with a white dot onto the mounting plates that have a white dot,
and install the propellers without a white dot onto the mounting plates that do not have a white dot. Press
the propeller down onto the mounting plate and rotate in the lock direction until secure.
For 1345 Propeller, attach propellers with the black nut onto motors with the black dot and spin
counter-clockwise to secure. Attach propellers with gray nut onto motors without a black dot and spin
clockwise to secure. Place all propellers onto the correct motor and tighten by hand to ensure security
before flight.
8. Preparing for Flight
Place the aircraft on a flat surface, in an open space, with the back facing you.
Appendix
Aircraft
Status Indicator Description
Slowly: Safe to fly,GPS working
Slowly: P-ATTI or ATTI
Quickly: Not connected
to remote controller
Slowly: Low battery level warning
Quickly: Critical low battery level warning
Solid: Critical error
Blinking Alternately:
Compass calibration required
Double: Vision Positioning
System working, no GPS
X2
www.dji.com/product/inspire-1
Gently pull the left (throttle) stick down to lower the aircraft
until it touches the ground. Pull both sticks to the bottom
inside corners to stop the motors.
After flight, change the aircraft back into Travel Mode. Do not
attempt this at the beach, over grass, or over monochromatic
carpet. Then place the aircraft on a flat surface and remove
the gimbal and camera for transport.
● Return to Home
Start the motors by pulling both control sticks to the bottom inside (or outside)
corners. Release the sticks once the motors start. Slowly push the left (throttle)
stick up to take off. Once in the air, toggle the Transformation Switch up to
raise the landing gear.
Remote controller is functioning normally
but is not connected to the aircraft.
Remote controller is functioning normally
and is connected to the aircraft.
Remote controller is in Slave Mode
and not connected to the aircraft.
Remote controller is in Slave Mode
and is connected to the aircraft.
B-B-B... Aircraft low battery warning
or remote controller error.
B—B—... Remote controller has been
idle for 5 minutes.
Remote Controller
Status LED
Using the Camera
● Adjust the camera parameters using the
Camera Settings Dial on the remote
controller or through the DJI Pilot app.
Press the Shutter Button/Video Record
Button to capture photos or record
videos.
● Adjust the tilt of the gimbal using the
Gimbal Dial.
● Download photos and video from the SD
card to your mobile device through the
DJI Pilot app. You may also use a SD
card reader to export files to your PC.
1. Press and hold the return home
button until the LED surrounding
the button is blinking white, and the
return home procedure is in
process. Press once to stop the
procedure.
2. The DJI Pilot app notifies users to
take action when the battery level
falls to a specified threshold. This
warning threshold can be set
within the DJI Pilot app. The
aircraft will land immediately when
it reaches Critical Low Battery
Level Warning.
3. Failsafe: The Inspire 1 will enter
RTH mode if remote controller
signal is lost.
DJI Pilot app
INSPIRE 1
www.dji.com
Creativity Unleashed
Gimbal Dial
( In the Camera screen of the DJI Pilot app )
Tap and confirm your selection. The landing gear will lower and the aircraft
will automatically land.
● It is highly recommended that you only take off when the Aircraft Status bar is green.
● The aircraft cannot take off if the Critical Low Battery Warning is active.
● The Intelligent Flight Battery must warm-up if the outside temperature is low. A
warning will display in the DJI Pilot app.
● Rotating propellers can be dangerous. Do not start the motors when there are people
nearby and always fly in a wide open area.
● Never stop the motors during flight. Power off the aircraft prior to switching off the
remote controller after landing.
©2014 DJI. All Rights Reserved
Designed by DJI. Printed in China.
Learn more information from:
Left stick / Down (Slowly)
RTH Button
Low
Battery Level
Low High
Battery Level
Watch the video tutorials on the official DJI website and read the following documents before using your Inspire 1 for the first time:
Inspire 1 Quick Start Guide, Disclaimer, Intelligent Flight Battery Safety Guidelines, Inspire 1 Safety Guidelines, In the Box,
Inspire 1 User Manual.
If you have purchased an Inspire 1 with dual remote controllers, the Master remote controller will connect to the aircraft
automatically when powered on. Master/Slave mode is disabled by default. Activate it and set it up through the DJI Pilot
app. The Master remote controller’s Status LED will show solid green when it connected to the aircraft. The Slave
remote controller’s Status LED will show solid blue when it is connected to the Master controller.
Connecting the Master remote controller to the Slave remote controller:
On the Master remote controller, launch the DJI Pilot app and go to the Camera page. Then tap on the top of your
screen to enter the remote controller settings window. Tap “Activate Master/Slave Mode”and select “Master”. Then
enter your desired connection password for the “Slave” remote controller.
On the Slave remote controller, select “Slave “ and tap “Search” to find the Master remote controller. Select the “Master”
remote controller from the “Master RC List” and input the connection password.
DJI Pilot
App
Toggle the
Transformation
Switch up
B
Left stick / Up (Slowly)
Start / Stop the motors
OR
8
1
The App’s
RTH Button
● If you have purchased the dual remote controller version, you must use the Master remote controller to deactivate Travel Mode.
3
6. Preparing the Aircraft
The aircraft is in Travel Mode during delivery. Follow these steps to change it
to Landing Mode before your first flight:
Insert the Intelligent Flight Battery into the battery compartment.
Power on the remote controller and the Intelligent Flight Battery.
Toggle the Transformation Switch up and down at least four times. Repeat
to change aircraft to Travel Mode.
Power off the aircraft before mounting the gimbal and camera.
Travel Mode
Landing Mode
2
1
5. Preparing the Remote Controller
Tilt the Mobile Device Holder to the desired position then adjust
the antennas as shown. The strength of the remote controller
signal is different when the antenna position is different.
The transmission signal between the aircraft and remote
controller will perform best when within the optimal
transmission range. If the signal is weak, fly the aircraft
closer to you to achieve optimal signal performance.
1
3
2
Strong Weak
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
Left Stick Right Stick
1
5
6
7
8
1
2
56
34
7
Gimbal Cover
Gimbal Connector
Mounting Place
Gimbal Lock
Locked
2
3
1
High
B
A
A
● While returning home, its
altitude can be adjusted by the
user to avoid obstructions.
Before taking off, make sure the aircraft
status bar in the DJI Pilot app shows “Safe
to Fly (GPS)”. Otherwise, the aircraft cannot
hover in place and record the Home Point.
10. Flight
● Manual Take - off & Landing：
Safe to Fly (GPS) ● Auto Taking - Off & Landing:
Tap and confirm your selection. The aircraft will automatically take off, retract
its landing gear, and hover at 1.5 meters after you tap and confirm Auto Take-off.
1
4. Charging
Using INSPIRE 1
● You can set the remote controller to different modes using the DJI Pilot app.
● Do not use other 2.4GHz devices at the same time to avoid signal interference.
1. Download the DJI Pilot App
Visit http://m.dji.net/djipilot or scan this QR code to
download the DJI Pilot app through your mobile device.
7. Mounting the Gimbal and Camera
3. Check Battery Levels
Press the Power Button once on both the Intelligent Flight Battery and remote controller to check battery levels. The
Intelligent Flight Battery must be fully charged before using it for the first time. Make sure both batteries are adequately
charged before each flight.
Press the power button once then press again and hold for 2 seconds to power on the remote controller. Repeat to power off.
Press the power button once, then press again and hold for 2 seconds to power on the Intelligent Flight Battery. Repeat to
power off.
9. Remote Controller Operation
The remote controller is by default set to Mode 2 ( throttle controlled by the left-hand stick ).
Adjust the tilt angle of camera by using the Gimbal Dial.
● For the best user experience, please use mobile devices with iOS 8.0 (or higher) and Android 4.1.2 (or higher).
● Read the Inspire 1 User Manual in the DJI Pilot app or official DJI website for more details.
●When not in P mode, the Inspire 1 will only maintain altitude, not position, and will drift with
wind or user inputs. Return to Home is not available in F mode.
●Only use the official DJI Inspire 1 charger for your Intelligent Flight Battery and remote controller.
● To charge the Inspire 1 Intelligent Flight Battery or the remote controller, connect it to power through the port to a
suitable power source (100-240V 50/60Hz).
● It is recommended to turn off the batteries before charging.
● Use the included charger to charge the Intelligent Flight Battery and the remote controller battery. When fully charged, the
battery LEDs on the Intelligent Flight Battery and remote controller will turn off.
Watch the tutorial videos at www.dji.com or in
the DJI Pilot app.
2. Watch the Tutorial Videos
The tutorial videos
Press the button on the side of the Mobile
Device Holder to release the clamp.
Place your device onto the clamp and adjust
the clamp to hold it securely.
Connect your mobile device to the remote
controller with a USB cable. Plug one end of
the cable into your mobile device, and the
other end into the USB port on the back of
the remote controller.
Remove the Gimbal Cover.
Rotate the Gimbal Lock to the unlocked position (to the right when
facing the nose of the aircraft). Insert the gimbal by aligning the
white mark on the gimbal with white mark on the Gimbal Lock.
Rotate the gimbal lock back into the locked position (to the left
when facing the nose of the aircraft).
1
Move the Flight Mode Switch to the right to select P mode. ( P mode is Positioning mode, A mode
is ATTI mode, and the F mode is Function mode. )
Power on the remote controller.
Power on the aircraft and wait for the self-check to complete. Do not move the aircraft during the
self-check.
Ensure the remote controller is linked to the aircraft before flight. Re-link the remote controller to the
aircraft if it fails to connect. Refer to the INSPIRE 1 User Manual on how to link.
Ensure the remote controller and your mobile device are connected with a USB cable. Launch the
DJI Pilot app when connecting to the aircraft for the first time, and follow the instructions within the app.
Launch the DJI Pilot app and tap “Camera”. Ensure the aircraft is functioning normally by
completing the Checklist.Beginner Mode is enabled by default when you launch the DJI Pilot app
for the first time. The aircraft’s altitude and flight distance is restricted when flying in Beginner Mode.
We recommend you fly in Beginner Mode when using the aircraft for the first time. You may disable
Beginner Mode in the settings page of the DJI Pilot app.
Calibrate the compass by tapping the Aircraft Status Bar in the app and selecting “Calibrate”. Then
follow the on-screen instructions.
For 1345s Propeller, install the propellers with a white dot onto the mounting plates that have a white dot,
and install the propellers without a white dot onto the mounting plates that do not have a white dot. Press
the propeller down onto the mounting plate and rotate in the lock direction until secure.
For 1345 Propeller, attach propellers with the black nut onto motors with the black dot and spin
counter-clockwise to secure. Attach propellers with gray nut onto motors without a black dot and spin
clockwise to secure. Place all propellers onto the correct motor and tighten by hand to ensure security
before flight.
8. Preparing for Flight
Place the aircraft on a flat surface, in an open space, with the back facing you.
Appendix
Aircraft
Status Indicator Description
Slowly: Safe to fly,GPS working
Slowly: P-ATTI or ATTI
Quickly: Not connected
to remote controller
Slowly: Low battery level warning
Quickly: Critical low battery level warning
Solid: Critical error
Blinking Alternately:
Compass calibration required
Double: Vision Positioning
System working, no GPS
X2
www.dji.com/product/inspire-1
Gently pull the left (throttle) stick down to lower the aircraft
until it touches the ground. Pull both sticks to the bottom
inside corners to stop the motors.
After flight, change the aircraft back into Travel Mode. Do not
attempt this at the beach, over grass, or over monochromatic
carpet. Then place the aircraft on a flat surface and remove
the gimbal and camera for transport.
● Return to Home
Start the motors by pulling both control sticks to the bottom inside (or outside)
corners. Release the sticks once the motors start. Slowly push the left (throttle)
stick up to take off. Once in the air, toggle the Transformation Switch up to
raise the landing gear.
Remote controller is functioning normally
but is not connected to the aircraft.
Remote controller is functioning normally
and is connected to the aircraft.
Remote controller is in Slave Mode
and not connected to the aircraft.
Remote controller is in Slave Mode
and is connected to the aircraft.
B-B-B... Aircraft low battery warning
or remote controller error.
B—B—... Remote controller has been
idle for 5 minutes.
Remote Controller
Status LED
Using the Camera
● Adjust the camera parameters using the
Camera Settings Dial on the remote
controller or through the DJI Pilot app.
Press the Shutter Button/Video Record
Button to capture photos or record
videos.
● Adjust the tilt of the gimbal using the
Gimbal Dial.
● Download photos and video from the SD
card to your mobile device through the
DJI Pilot app. You may also use a SD
card reader to export files to your PC.
1. Press and hold the return home
button until the LED surrounding
the button is blinking white, and the
return home procedure is in
process. Press once to stop the
procedure.
2. The DJI Pilot app notifies users to
take action when the battery level
falls to a specified threshold. This
warning threshold can be set
within the DJI Pilot app. The
aircraft will land immediately when
it reaches Critical Low Battery
Level Warning.
3. Failsafe: The Inspire 1 will enter
RTH mode if remote controller
signal is lost.
DJI Pilot app
INSPIRE 1
www.dji.com
Creativity Unleashed
Gimbal Dial
( In the Camera screen of the DJI Pilot app )
Tap and confirm your selection. The landing gear will lower and the aircraft
will automatically land.
● It is highly recommended that you only take off when the Aircraft Status bar is green.
● The aircraft cannot take off if the Critical Low Battery Warning is active.
● The Intelligent Flight Battery must warm-up if the outside temperature is low. A
warning will display in the DJI Pilot app.
● Rotating propellers can be dangerous. Do not start the motors when there are people
nearby and always fly in a wide open area.
● Never stop the motors during flight. Power off the aircraft prior to switching off the
remote controller after landing.
©2014 DJI. All Rights Reserved
Designed by DJI. Printed in China.
Learn more information from:
Left stick / Down (Slowly)
RTH Button
Low
Battery Level
Low High
Battery Level
Watch the video tutorials on the official DJI website and read the following documents before using your Inspire 1 for the first time:
Inspire 1 Quick Start Guide, Disclaimer, Intelligent Flight Battery Safety Guidelines, Inspire 1 Safety Guidelines, In the Box,
Inspire 1 User Manual.
If you have purchased an Inspire 1 with dual remote controllers, the Master remote controller will connect to the aircraft
automatically when powered on. Master/Slave mode is disabled by default. Activate it and set it up through the DJI Pilot
app. The Master remote controller’s Status LED will show solid green when it connected to the aircraft. The Slave
remote controller’s Status LED will show solid blue when it is connected to the Master controller.
Connecting the Master remote controller to the Slave remote controller:
On the Master remote controller, launch the DJI Pilot app and go to the Camera page. Then tap on the top of your
screen to enter the remote controller settings window. Tap “Activate Master/Slave Mode”and select “Master”. Then
enter your desired connection password for the “Slave” remote controller.
On the Slave remote controller, select “Slave “ and tap “Search” to find the Master remote controller. Select the “Master”
remote controller from the “Master RC List” and input the connection password.
DJI Pilot
App
Toggle the
Transformation
Switch up
B
Left stick / Up (Slowly)
Start / Stop the motors
OR
8
1
The App’s
RTH Button
● If you have purchased the dual remote controller version, you must use the Master remote controller to deactivate Travel Mode.
3
6. Preparing the Aircraft
The aircraft is in Travel Mode during delivery. Follow these steps to change it
to Landing Mode before your first flight:
Insert the Intelligent Flight Battery into the battery compartment.
Power on the remote controller and the Intelligent Flight Battery.
Toggle the Transformation Switch up and down at least four times. Repeat
to change aircraft to Travel Mode.
Power off the aircraft before mounting the gimbal and camera.
Travel Mode
Landing Mode
2
1
5. Preparing the Remote Controller
Tilt the Mobile Device Holder to the desired position then adjust
the antennas as shown. The strength of the remote controller
signal is different when the antenna position is different.
The transmission signal between the aircraft and remote
controller will perform best when within the optimal
transmission range. If the signal is weak, fly the aircraft
closer to you to achieve optimal signal performance.
1
3
2
Strong Weak
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
Left Stick Right Stick
1
5
6
7
8
1
2
56
34
7
Gimbal Cover
Gimbal Connector
Mounting Place
Gimbal Lock
Locked
2
3
1
High
B
A
A
● While returning home, its
altitude can be adjusted by the
user to avoid obstructions.
Before taking off, make sure the aircraft
status bar in the DJI Pilot app shows “Safe
to Fly (GPS)”. Otherwise, the aircraft cannot
hover in place and record the Home Point.
10. Flight
● Manual Take - off & Landing：
Safe to Fly (GPS) ● Auto Taking - Off & Landing:
Tap and confirm your selection. The aircraft will automatically take off, retract
its landing gear, and hover at 1.5 meters after you tap and confirm Auto Take-off.
1
4. Charging
Using INSPIRE 1
● You can set the remote controller to different modes using the DJI Pilot app.
● Do not use other 2.4GHz devices at the same time to avoid signal interference.
1. Download the DJI Pilot App
Visit http://m.dji.net/djipilot or scan this QR code to
download the DJI Pilot app through your mobile device.
7. Mounting the Gimbal and Camera
3. Check Battery Levels
Press the Power Button once on both the Intelligent Flight Battery and remote controller to check battery levels. The
Intelligent Flight Battery must be fully charged before using it for the first time. Make sure both batteries are adequately
charged before each flight.
Press the power button once then press again and hold for 2 seconds to power on the remote controller. Repeat to power off.
Press the power button once, then press again and hold for 2 seconds to power on the Intelligent Flight Battery. Repeat to
power off.
9. Remote Controller Operation
The remote controller is by default set to Mode 2 ( throttle controlled by the left-hand stick ).
Adjust the tilt angle of camera by using the Gimbal Dial.
● For the best user experience, please use mobile devices with iOS 8.0 (or higher) and Android 4.1.2 (or higher).
● Read the Inspire 1 User Manual in the DJI Pilot app or official DJI website for more details.
●When not in P mode, the Inspire 1 will only maintain altitude, not position, and will drift with
wind or user inputs. Return to Home is not available in F mode.
●Only use the official DJI Inspire 1 charger for your Intelligent Flight Battery and remote controller.
● To charge the Inspire 1 Intelligent Flight Battery or the remote controller, connect it to power through the port to a
suitable power source (100-240V 50/60Hz).
● It is recommended to turn off the batteries before charging.
● Use the included charger to charge the Intelligent Flight Battery and the remote controller battery. When fully charged, the
battery LEDs on the Intelligent Flight Battery and remote controller will turn off.
Watch the tutorial videos at www.dji.com or in
the DJI Pilot app.
2. Watch the Tutorial Videos
The tutorial videos
Press the button on the side of the Mobile
Device Holder to release the clamp.
Place your device onto the clamp and adjust
the clamp to hold it securely.
Connect your mobile device to the remote
controller with a USB cable. Plug one end of
the cable into your mobile device, and the
other end into the USB port on the back of
the remote controller.
Remove the Gimbal Cover.
Rotate the Gimbal Lock to the unlocked position (to the right when
facing the nose of the aircraft). Insert the gimbal by aligning the
white mark on the gimbal with white mark on the Gimbal Lock.
Rotate the gimbal lock back into the locked position (to the left
when facing the nose of the aircraft).
1
Move the Flight Mode Switch to the right to select P mode. ( P mode is Positioning mode, A mode
is ATTI mode, and the F mode is Function mode. )
Power on the remote controller.
Power on the aircraft and wait for the self-check to complete. Do not move the aircraft during the
self-check.
Ensure the remote controller is linked to the aircraft before flight. Re-link the remote controller to the
aircraft if it fails to connect. Refer to the INSPIRE 1 User Manual on how to link.
Ensure the remote controller and your mobile device are connected with a USB cable. Launch the
DJI Pilot app when connecting to the aircraft for the first time, and follow the instructions within the app.
Launch the DJI Pilot app and tap “Camera”. Ensure the aircraft is functioning normally by
completing the Checklist.Beginner Mode is enabled by default when you launch the DJI Pilot app
for the first time. The aircraft’s altitude and flight distance is restricted when flying in Beginner Mode.
We recommend you fly in Beginner Mode when using the aircraft for the first time. You may disable
Beginner Mode in the settings page of the DJI Pilot app.
Calibrate the compass by tapping the Aircraft Status Bar in the app and selecting “Calibrate”. Then
follow the on-screen instructions.
For 1345s Propeller, install the propellers with a white dot onto the mounting plates that have a white dot,
and install the propellers without a white dot onto the mounting plates that do not have a white dot. Press
the propeller down onto the mounting plate and rotate in the lock direction until secure.
For 1345 Propeller, attach propellers with the black nut onto motors with the black dot and spin
counter-clockwise to secure. Attach propellers with gray nut onto motors without a black dot and spin
clockwise to secure. Place all propellers onto the correct motor and tighten by hand to ensure security
before flight.
8. Preparing for Flight
Place the aircraft on a flat surface, in an open space, with the back facing you.
Appendix
Aircraft
Status Indicator Description
Slowly: Safe to fly,GPS working
Slowly: P-ATTI or ATTI
Quickly: Not connected
to remote controller
Slowly: Low battery level warning
Quickly: Critical low battery level warning
Solid: Critical error
Blinking Alternately:
Compass calibration required
Double: Vision Positioning
System working, no GPS
X2
www.dji.com/product/inspire-1
Gently pull the left (throttle) stick down to lower the aircraft
until it touches the ground. Pull both sticks to the bottom
inside corners to stop the motors.
After flight, change the aircraft back into Travel Mode. Do not
attempt this at the beach, over grass, or over monochromatic
carpet. Then place the aircraft on a flat surface and remove
the gimbal and camera for transport.
● Return to Home
Start the motors by pulling both control sticks to the bottom inside (or outside)
corners. Release the sticks once the motors start. Slowly push the left (throttle)
stick up to take off. Once in the air, toggle the Transformation Switch up to
raise the landing gear.
Remote controller is functioning normally
but is not connected to the aircraft.
Remote controller is functioning normally
and is connected to the aircraft.
Remote controller is in Slave Mode
and not connected to the aircraft.
Remote controller is in Slave Mode
and is connected to the aircraft.
B-B-B... Aircraft low battery warning
or remote controller error.
B—B—... Remote controller has been
idle for 5 minutes.
Remote Controller
Status LED
Using the Camera
● Adjust the camera parameters using the
Camera Settings Dial on the remote
controller or through the DJI Pilot app.
Press the Shutter Button/Video Record
Button to capture photos or record
videos.
● Adjust the tilt of the gimbal using the
Gimbal Dial.
● Download photos and video from the SD
card to your mobile device through the
DJI Pilot app. You may also use a SD
card reader to export files to your PC.
1. Press and hold the return home
button until the LED surrounding
the button is blinking white, and the
return home procedure is in
process. Press once to stop the
procedure.
2. The DJI Pilot app notifies users to
take action when the battery level
falls to a specified threshold. This
warning threshold can be set
within the DJI Pilot app. The
aircraft will land immediately when
it reaches Critical Low Battery
Level Warning.
3. Failsafe: The Inspire 1 will enter
RTH mode if remote controller
signal is lost.
DJI Pilot app
INSPIRE 1
www.dji.com
Creativity Unleashed
Gimbal Dial
( In the Camera screen of the DJI Pilot app )
Tap and confirm your selection. The landing gear will lower and the aircraft
will automatically land.
● It is highly recommended that you only take off when the Aircraft Status bar is green.
● The aircraft cannot take off if the Critical Low Battery Warning is active.
● The Intelligent Flight Battery must warm-up if the outside temperature is low. A
warning will display in the DJI Pilot app.
● Rotating propellers can be dangerous. Do not start the motors when there are people
nearby and always fly in a wide open area.
● Never stop the motors during flight. Power off the aircraft prior to switching off the
remote controller after landing.
©2014 DJI. All Rights Reserved
Designed by DJI. Printed in China.
Learn more information from:
Left stick / Down (Slowly)
RTH Button
Low
Battery Level
Low High
Battery Level
Watch the video tutorials on the official DJI website and read the following documents before using your Inspire 1 for the first time:
Inspire 1 Quick Start Guide, Disclaimer, Intelligent Flight Battery Safety Guidelines, Inspire 1 Safety Guidelines, In the Box,
Inspire 1 User Manual.
If you have purchased an Inspire 1 with dual remote controllers, the Master remote controller will connect to the aircraft
automatically when powered on. Master/Slave mode is disabled by default. Activate it and set it up through the DJI Pilot
app. The Master remote controller’s Status LED will show solid green when it connected to the aircraft. The Slave
remote controller’s Status LED will show solid blue when it is connected to the Master controller.
Connecting the Master remote controller to the Slave remote controller:
On the Master remote controller, launch the DJI Pilot app and go to the Camera page. Then tap on the top of your
screen to enter the remote controller settings window. Tap “Activate Master/Slave Mode”and select “Master”. Then
enter your desired connection password for the “Slave” remote controller.
On the Slave remote controller, select “Slave “ and tap “Search” to find the Master remote controller. Select the “Master”
remote controller from the “Master RC List” and input the connection password.
DJI Pilot
App
Toggle the
Transformation
Switch up
B
Left stick / Up (Slowly)
Start / Stop the motors
OR
8
1
The App’s
RTH Button
● If you have purchased the dual remote controller version, you must use the Master remote controller to deactivate Travel Mode.
3
6. Preparing the Aircraft
The aircraft is in Travel Mode during delivery. Follow these steps to change it
to Landing Mode before your first flight:
Insert the Intelligent Flight Battery into the battery compartment.
Power on the remote controller and the Intelligent Flight Battery.
Toggle the Transformation Switch up and down at least four times. Repeat
to change aircraft to Travel Mode.
Power off the aircraft before mounting the gimbal and camera.
Travel Mode
Landing Mode
2
1
5. Preparing the Remote Controller
Tilt the Mobile Device Holder to the desired position then adjust
the antennas as shown. The strength of the remote controller
signal is different when the antenna position is different.
The transmission signal between the aircraft and remote
controller will perform best when within the optimal
transmission range. If the signal is weak, fly the aircraft
closer to you to achieve optimal signal performance.
1
3
2
Strong Weak
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
Left Stick Right Stick
1
5
6
7
8
1
2
56
34
7
Gimbal Cover
Gimbal Connector
Mounting Place
Gimbal Lock
Locked
2
3
1
High
B
A
A
● While returning home, its
altitude can be adjusted by the
user to avoid obstructions.
Before taking off, make sure the aircraft
status bar in the DJI Pilot app shows “Safe
to Fly (GPS)”. Otherwise, the aircraft cannot
hover in place and record the Home Point.
10. Flight
● Manual Take - off & Landing：
Safe to Fly (GPS) ● Auto Taking - Off & Landing:
Tap and confirm your selection. The aircraft will automatically take off, retract
its landing gear, and hover at 1.5 meters after you tap and confirm Auto Take-off.
1
4. Charging
Using INSPIRE 1
● You can set the remote controller to different modes using the DJI Pilot app.
● Do not use other 2.4GHz devices at the same time to avoid signal interference.
1. Download the DJI Pilot App
Visit http://m.dji.net/djipilot or scan this QR code to
download the DJI Pilot app through your mobile device.
7. Mounting the Gimbal and Camera
3. Check Battery Levels
Press the Power Button once on both the Intelligent Flight Battery and remote controller to check battery levels. The
Intelligent Flight Battery must be fully charged before using it for the first time. Make sure both batteries are adequately
charged before each flight.
Press the power button once then press again and hold for 2 seconds to power on the remote controller. Repeat to power off.
Press the power button once, then press again and hold for 2 seconds to power on the Intelligent Flight Battery. Repeat to
power off.
9. Remote Controller Operation
The remote controller is by default set to Mode 2 ( throttle controlled by the left-hand stick ).
Adjust the tilt angle of camera by using the Gimbal Dial.
● For the best user experience, please use mobile devices with iOS 8.0 (or higher) and Android 4.1.2 (or higher).
● Read the Inspire 1 User Manual in the DJI Pilot app or official DJI website for more details.
●When not in P mode, the Inspire 1 will only maintain altitude, not position, and will drift with
wind or user inputs. Return to Home is not available in F mode.
●Only use the official DJI Inspire 1 charger for your Intelligent Flight Battery and remote controller.
● To charge the Inspire 1 Intelligent Flight Battery or the remote controller, connect it to power through the port to a
suitable power source (100-240V 50/60Hz).
● It is recommended to turn off the batteries before charging.
● Use the included charger to charge the Intelligent Flight Battery and the remote controller battery. When fully charged, the
battery LEDs on the Intelligent Flight Battery and remote controller will turn off.
Watch the tutorial videos at www.dji.com or in
the DJI Pilot app.
2. Watch the Tutorial Videos
The tutorial videos
Press the button on the side of the Mobile
Device Holder to release the clamp.
Place your device onto the clamp and adjust
the clamp to hold it securely.
Connect your mobile device to the remote
controller with a USB cable. Plug one end of
the cable into your mobile device, and the
other end into the USB port on the back of
the remote controller.
Remove the Gimbal Cover.
Rotate the Gimbal Lock to the unlocked position (to the right when
facing the nose of the aircraft). Insert the gimbal by aligning the
white mark on the gimbal with white mark on the Gimbal Lock.
Rotate the gimbal lock back into the locked position (to the left
when facing the nose of the aircraft).
1
Move the Flight Mode Switch to the right to select P mode. ( P mode is Positioning mode, A mode
is ATTI mode, and the F mode is Function mode. )
Power on the remote controller.
Power on the aircraft and wait for the self-check to complete. Do not move the aircraft during the
self-check.
Ensure the remote controller is linked to the aircraft before flight. Re-link the remote controller to the
aircraft if it fails to connect. Refer to the INSPIRE 1 User Manual on how to link.
Ensure the remote controller and your mobile device are connected with a USB cable. Launch the
DJI Pilot app when connecting to the aircraft for the first time, and follow the instructions within the app.
Launch the DJI Pilot app and tap “Camera”. Ensure the aircraft is functioning normally by
completing the Checklist.Beginner Mode is enabled by default when you launch the DJI Pilot app
for the first time. The aircraft’s altitude and flight distance is restricted when flying in Beginner Mode.
We recommend you fly in Beginner Mode when using the aircraft for the first time. You may disable
Beginner Mode in the settings page of the DJI Pilot app.
Calibrate the compass by tapping the Aircraft Status Bar in the app and selecting “Calibrate”. Then
follow the on-screen instructions.
For 1345s Propeller, install the propellers with a white dot onto the mounting plates that have a white dot,
and install the propellers without a white dot onto the mounting plates that do not have a white dot. Press
the propeller down onto the mounting plate and rotate in the lock direction until secure.
For 1345 Propeller, attach propellers with the black nut onto motors with the black dot and spin
counter-clockwise to secure. Attach propellers with gray nut onto motors without a black dot and spin
clockwise to secure. Place all propellers onto the correct motor and tighten by hand to ensure security
before flight.
8. Preparing for Flight
Place the aircraft on a flat surface, in an open space, with the back facing you.
Appendix
Aircraft
Status Indicator Description
Slowly: Safe to fly,GPS working
Slowly: P-ATTI or ATTI
Quickly: Not connected
to remote controller
Slowly: Low battery level warning
Quickly: Critical low battery level warning
Solid: Critical error
Blinking Alternately:
Compass calibration required
Double: Vision Positioning
System working, no GPS
X2
www.dji.com/product/inspire-1
Gently pull the left (throttle) stick down to lower the aircraft
until it touches the ground. Pull both sticks to the bottom
inside corners to stop the motors.
After flight, change the aircraft back into Travel Mode. Do not
attempt this at the beach, over grass, or over monochromatic
carpet. Then place the aircraft on a flat surface and remove
the gimbal and camera for transport.
● Return to Home
Start the motors by pulling both control sticks to the bottom inside (or outside)
corners. Release the sticks once the motors start. Slowly push the left (throttle)
stick up to take off. Once in the air, toggle the Transformation Switch up to
raise the landing gear.
Remote controller is functioning normally
but is not connected to the aircraft.
Remote controller is functioning normally
and is connected to the aircraft.
Remote controller is in Slave Mode
and not connected to the aircraft.
Remote controller is in Slave Mode
and is connected to the aircraft.
B-B-B... Aircraft low battery warning
or remote controller error.
B—B—... Remote controller has been
idle for 5 minutes.
Remote Controller
Status LED
Using the Camera
● Adjust the camera parameters using the
Camera Settings Dial on the remote
controller or through the DJI Pilot app.
Press the Shutter Button/Video Record
Button to capture photos or record
videos.
● Adjust the tilt of the gimbal using the
Gimbal Dial.
● Download photos and video from the SD
card to your mobile device through the
DJI Pilot app. You may also use a SD
card reader to export files to your PC.
1. Press and hold the return home
button until the LED surrounding
the button is blinking white, and the
return home procedure is in
process. Press once to stop the
procedure.
2. The DJI Pilot app notifies users to
take action when the battery level
falls to a specified threshold. This
warning threshold can be set
within the DJI Pilot app. The
aircraft will land immediately when
it reaches Critical Low Battery
Level Warning.
3. Failsafe: The Inspire 1 will enter
RTH mode if remote controller
signal is lost.
DJI Pilot app
INSPIRE 1
www.dji.com
Creativity Unleashed
Gimbal Dial
( In the Camera screen of the DJI Pilot app )
Tap and confirm your selection. The landing gear will lower and the aircraft
will automatically land.
● It is highly recommended that you only take off when the Aircraft Status bar is green.
● The aircraft cannot take off if the Critical Low Battery Warning is active.
● The Intelligent Flight Battery must warm-up if the outside temperature is low. A
warning will display in the DJI Pilot app.
● Rotating propellers can be dangerous. Do not start the motors when there are people
nearby and always fly in a wide open area.
● Never stop the motors during flight. Power off the aircraft prior to switching off the
remote controller after landing.
©2014 DJI. All Rights Reserved
Designed by DJI. Printed in China.
Learn more information from:
Left stick / Down (Slowly)
RTH Button
Low
Battery Level
Low High
Battery Level
Watch the video tutorials on the official DJI website and read the following documents before using your Inspire 1 for the first time:
Inspire 1 Quick Start Guide, Disclaimer, Intelligent Flight Battery Safety Guidelines, Inspire 1 Safety Guidelines, In the Box,
Inspire 1 User Manual.
If you have purchased an Inspire 1 with dual remote controllers, the Master remote controller will connect to the aircraft
automatically when powered on. Master/Slave mode is disabled by default. Activate it and set it up through the DJI Pilot
app. The Master remote controller’s Status LED will show solid green when it connected to the aircraft. The Slave
remote controller’s Status LED will show solid blue when it is connected to the Master controller.
Connecting the Master remote controller to the Slave remote controller:
On the Master remote controller, launch the DJI Pilot app and go to the Camera page. Then tap on the top of your
screen to enter the remote controller settings window. Tap “Activate Master/Slave Mode”and select “Master”. Then
enter your desired connection password for the “Slave” remote controller.
On the Slave remote controller, select “Slave “ and tap “Search” to find the Master remote controller. Select the “Master”
remote controller from the “Master RC List” and input the connection password.
DJI Pilot
App
Toggle the
Transformation
Switch up
B
Left stick / Up (Slowly)
Start / Stop the motors
OR
8
1
The App’s
RTH Button
● If you have purchased the dual remote controller version, you must use the Master remote controller to deactivate Travel Mode.
3
6. Preparing the Aircraft
The aircraft is in Travel Mode during delivery. Follow these steps to change it
to Landing Mode before your first flight:
Insert the Intelligent Flight Battery into the battery compartment.
Power on the remote controller and the Intelligent Flight Battery.
Toggle the Transformation Switch up and down at least four times. Repeat
to change aircraft to Travel Mode.
Power off the aircraft before mounting the gimbal and camera.
Travel Mode
Landing Mode
2
1
5. Preparing the Remote Controller
Tilt the Mobile Device Holder to the desired position then adjust
the antennas as shown. The strength of the remote controller
signal is different when the antenna position is different.
The transmission signal between the aircraft and remote
controller will perform best when within the optimal
transmission range. If the signal is weak, fly the aircraft
closer to you to achieve optimal signal performance.
1
3
2
Strong Weak
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
Left Stick Right Stick
1
5
6
7
8
1
2
56
34
7
Gimbal Cover
Gimbal Connector
Mounting Place
Gimbal Lock
Locked
2
3
1
High
B
A
A
● While returning home, its
altitude can be adjusted by the
user to avoid obstructions.
Before taking off, make sure the aircraft
status bar in the DJI Pilot app shows “Safe
to Fly (GPS)”. Otherwise, the aircraft cannot
hover in place and record the Home Point.
10. Flight
● Manual Take - off & Landing：
Safe to Fly (GPS) ● Auto Taking - Off & Landing:
Tap and confirm your selection. The aircraft will automatically take off, retract
its landing gear, and hover at 1.5 meters after you tap and confirm Auto Take-off.
1
4. Charging
Using INSPIRE 1
● You can set the remote controller to different modes using the DJI Pilot app.
● Do not use other 2.4GHz devices at the same time to avoid signal interference.
1. Download the DJI Pilot App
Visit http://m.dji.net/djipilot or scan this QR code to
download the DJI Pilot app through your mobile device.
7. Mounting the Gimbal and Camera
3. Check Battery Levels
Press the Power Button once on both the Intelligent Flight Battery and remote controller to check battery levels. The
Intelligent Flight Battery must be fully charged before using it for the first time. Make sure both batteries are adequately
charged before each flight.
Press the power button once then press again and hold for 2 seconds to power on the remote controller. Repeat to power off.
Press the power button once, then press again and hold for 2 seconds to power on the Intelligent Flight Battery. Repeat to
power off.
9. Remote Controller Operation
The remote controller is by default set to Mode 2 ( throttle controlled by the left-hand stick ).
Adjust the tilt angle of camera by using the Gimbal Dial.
● For the best user experience, please use mobile devices with iOS 8.0 (or higher) and Android 4.1.2 (or higher).
● Read the Inspire 1 User Manual in the DJI Pilot app or official DJI website for more details.
●When not in P mode, the Inspire 1 will only maintain altitude, not position, and will drift with
wind or user inputs. Return to Home is not available in F mode.
●Only use the official DJI Inspire 1 charger for your Intelligent Flight Battery and remote controller.
● To charge the Inspire 1 Intelligent Flight Battery or the remote controller, connect it to power through the port to a
suitable power source (100-240V 50/60Hz).
● It is recommended to turn off the batteries before charging.
● Use the included charger to charge the Intelligent Flight Battery and the remote controller battery. When fully charged, the
battery LEDs on the Intelligent Flight Battery and remote controller will turn off.
Watch the tutorial videos at www.dji.com or in
the DJI Pilot app.
2. Watch the Tutorial Videos
The tutorial videos
Press the button on the side of the Mobile
Device Holder to release the clamp.
Place your device onto the clamp and adjust
the clamp to hold it securely.
Connect your mobile device to the remote
controller with a USB cable. Plug one end of
the cable into your mobile device, and the
other end into the USB port on the back of
the remote controller.
Remove the Gimbal Cover.
Rotate the Gimbal Lock to the unlocked position (to the right when
facing the nose of the aircraft). Insert the gimbal by aligning the
white mark on the gimbal with white mark on the Gimbal Lock.
Rotate the gimbal lock back into the locked position (to the left
when facing the nose of the aircraft).
1
Move the Flight Mode Switch to the right to select P mode. ( P mode is Positioning mode, A mode
is ATTI mode, and the F mode is Function mode. )
Power on the remote controller.
Power on the aircraft and wait for the self-check to complete. Do not move the aircraft during the
self-check.
Ensure the remote controller is linked to the aircraft before flight. Re-link the remote controller to the
aircraft if it fails to connect. Refer to the INSPIRE 1 User Manual on how to link.
Ensure the remote controller and your mobile device are connected with a USB cable. Launch the
DJI Pilot app when connecting to the aircraft for the first time, and follow the instructions within the app.
Launch the DJI Pilot app and tap “Camera”. Ensure the aircraft is functioning normally by
completing the Checklist.Beginner Mode is enabled by default when you launch the DJI Pilot app
for the first time. The aircraft’s altitude and flight distance is restricted when flying in Beginner Mode.
We recommend you fly in Beginner Mode when using the aircraft for the first time. You may disable
Beginner Mode in the settings page of the DJI Pilot app.
Calibrate the compass by tapping the Aircraft Status Bar in the app and selecting “Calibrate”. Then
follow the on-screen instructions.
For 1345s Propeller, install the propellers with a white dot onto the mounting plates that have a white dot,
and install the propellers without a white dot onto the mounting plates that do not have a white dot. Press
the propeller down onto the mounting plate and rotate in the lock direction until secure.
For 1345 Propeller, attach propellers with the black nut onto motors with the black dot and spin
counter-clockwise to secure. Attach propellers with gray nut onto motors without a black dot and spin
clockwise to secure. Place all propellers onto the correct motor and tighten by hand to ensure security
before flight.
8. Preparing for Flight
Place the aircraft on a flat surface, in an open space, with the back facing you.
Appendix
Aircraft
Status Indicator Description
Slowly: Safe to fly,GPS working
Slowly: P-ATTI or ATTI
Quickly: Not connected
to remote controller
Slowly: Low battery level warning
Quickly: Critical low battery level warning
Solid: Critical error
Blinking Alternately:
Compass calibration required
Double: Vision Positioning
System working, no GPS
X2
www.dji.com/product/inspire-1
Gently pull the left (throttle) stick down to lower the aircraft
until it touches the ground. Pull both sticks to the bottom
inside corners to stop the motors.
After flight, change the aircraft back into Travel Mode. Do not
attempt this at the beach, over grass, or over monochromatic
carpet. Then place the aircraft on a flat surface and remove
the gimbal and camera for transport.
● Return to Home
Start the motors by pulling both control sticks to the bottom inside (or outside)
corners. Release the sticks once the motors start. Slowly push the left (throttle)
stick up to take off. Once in the air, toggle the Transformation Switch up to
raise the landing gear.
Remote controller is functioning normally
but is not connected to the aircraft.
Remote controller is functioning normally
and is connected to the aircraft.
Remote controller is in Slave Mode
and not connected to the aircraft.
Remote controller is in Slave Mode
and is connected to the aircraft.
B-B-B... Aircraft low battery warning
or remote controller error.
B—B—... Remote controller has been
idle for 5 minutes.
Remote Controller
Status LED
Using the Camera
● Adjust the camera parameters using the
Camera Settings Dial on the remote
controller or through the DJI Pilot app.
Press the Shutter Button/Video Record
Button to capture photos or record
videos.
● Adjust the tilt of the gimbal using the
Gimbal Dial.
● Download photos and video from the SD
card to your mobile device through the
DJI Pilot app. You may also use a SD
card reader to export files to your PC.
1. Press and hold the return home
button until the LED surrounding
the button is blinking white, and the
return home procedure is in
process. Press once to stop the
procedure.
2. The DJI Pilot app notifies users to
take action when the battery level
falls to a specified threshold. This
warning threshold can be set
within the DJI Pilot app. The
aircraft will land immediately when
it reaches Critical Low Battery
Level Warning.
3. Failsafe: The Inspire 1 will enter
RTH mode if remote controller
signal is lost.
DJI Pilot app
INSPIRE 1
www.dji.com
Creativity Unleashed
Gimbal Dial
( In the Camera screen of the DJI Pilot app )
Tap and confirm your selection. The landing gear will lower and the aircraft
will automatically land.
● It is highly recommended that you only take off when the Aircraft Status bar is green.
● The aircraft cannot take off if the Critical Low Battery Warning is active.
● The Intelligent Flight Battery must warm-up if the outside temperature is low. A
warning will display in the DJI Pilot app.
● Rotating propellers can be dangerous. Do not start the motors when there are people
nearby and always fly in a wide open area.
● Never stop the motors during flight. Power off the aircraft prior to switching off the
remote controller after landing.
©2014 DJI. All Rights Reserved
Designed by DJI. Printed in China.
Learn more information from:
Left stick / Down (Slowly)
RTH Button
Low
Battery Level
Low High
Battery Level
Watch the video tutorials on the official DJI website and read the following documents before using your Inspire 1 for the first time:
Inspire 1 Quick Start Guide, Disclaimer, Intelligent Flight Battery Safety Guidelines, Inspire 1 Safety Guidelines, In the Box,
Inspire 1 User Manual.
If you have purchased an Inspire 1 with dual remote controllers, the Master remote controller will connect to the aircraft
automatically when powered on. Master/Slave mode is disabled by default. Activate it and set it up through the DJI Pilot
app. The Master remote controller’s Status LED will show solid green when it connected to the aircraft. The Slave
remote controller’s Status LED will show solid blue when it is connected to the Master controller.
Connecting the Master remote controller to the Slave remote controller:
On the Master remote controller, launch the DJI Pilot app and go to the Camera page. Then tap on the top of your
screen to enter the remote controller settings window. Tap “Activate Master/Slave Mode”and select “Master”. Then
enter your desired connection password for the “Slave” remote controller.
On the Slave remote controller, select “Slave “ and tap “Search” to find the Master remote controller. Select the “Master”
remote controller from the “Master RC List” and input the connection password.
DJI Pilot
App
Toggle the
Transformation
Switch up
B
Table of contents
Other dji Drone manuals
dji
dji PHANTOM 4 PRO User manual
dji
dji PHANTOM 4 User manual
dji
dji AGRAS MG-1S RTK User manual
dji
dji GOGGLES 2 MOTION COMBO User manual
dji
dji FlameWheel550 User manual
dji
dji PHANTOM 4 PRO User manual
dji
dji SPARK User manual
dji
dji MINI 3 PRO User manual
dji
dji MAVIC MINI User manual
dji
dji WIND-4 User manual
