DMP Electronics XR550 series User manual

INSTALLATION GUIDE
XR150/XR550 INTERNATIONAL
SERIES CONTROL PANEL

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
MODEL XR150/XR550 INTERNATIONAL SERIES PANELS
INSTALLATION GUIDE
© 2021 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.

XR150INT/XR550INT Series Installation Guide Digital Monitoring Products
i
TABLE OF CONTENTS
Product Specications Summary
1.1 Power Supply ..................................................................................................... 1
1.2 Communication................................................................................................... 1
1.3 Panel Zones........................................................................................................ 1
1.4 Keypad Bus ........................................................................................................ 1
1.5 LX500-LX900 Bus™............................................................................................. 1
1.6 Outputs.............................................................................................................. 1
1.7 EnclosureSpecications ...................................................................................... 2
Panel Features
2.1 Description......................................................................................................... 2
2.2 Zone Expansion .................................................................................................. 2
2.3 Output Expansion ............................................................................................... 2
2.4 Central Station Communication ............................................................................ 2
2.5 Caution Notes..................................................................................................... 3
2.6 Compliance Instructions ...................................................................................... 3
System Components
3.1 SpecicandNon-specicWiredInterconnections .................................................. 4
3.2 Lightning Protection ............................................................................................ 4
3.3 Accessory Devices............................................................................................... 5
Installation
4.1 Mounting the Enclosure....................................................................................... 6
4.2 Mounting Keypads and Zone Expansion Modules ................................................... 7
4.3 Connecting LX-Bus™, AX-Bus™ and Keypad Bus Devices ....................................... 8
4.4 WirelessKeypadAssociation ................................................................................ 8
5.1 AC Terminals 1 and 2 .......................................................................................... 9
5.2 50VA-75VA 3-Pin Header for Transformer Types .................................................... 9
Secondary Power Supply
6.1 Battery Terminals 3 and 4.................................................................................... 9
6.2 Earth Ground (GND) ........................................................................................... 9
6.3 Battery Only Restart............................................................................................ 9
6.4 Battery Replacement Period................................................................................. 9
6.5 Discharge/Recharge ............................................................................................ 9
6.6 Battery Supervision ............................................................................................10
6.7 BatteryCuto....................................................................................................10
6.8 Power Requirements ..........................................................................................10
6.9 Standby Battery Selection...................................................................................12
Bell Output
7.1 Terminals 5 and 6 ..............................................................................................13
Keypad Bus
8.1 Description........................................................................................................13
8.2 Terminal 7 - RED................................................................................................13
8.3 Terminal8-YELLOW .........................................................................................13
8.4 Terminal 9 - GREEN ...........................................................................................13
8.5 Terminal 10 - BLACK ..........................................................................................13
8.6 Programming (PROG) Connection .......................................................................13
8.7 Keypad Bus LEDs ...............................................................................................13
8.8 OVC LED(s) .......................................................................................................13
Smoke and Glassbreak Detector Output
9.1 Terminals 11 and 12...........................................................................................14
9.2 Current Rating ...................................................................................................14

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
ii
TABLE OF CONTENTS
Protection Zones
10.1 Terminals 13–24 ................................................................................................14
10.2 Operational Parameters ......................................................................................14
10.3 Zone Response Time..........................................................................................15
10.4 Keyswitch Arming Zone ......................................................................................15
Powered Zones for 2-Wire Smoke Detectors
11.1 Terminals 25–26 and 27–28................................................................................15
Dry Contact Relay Outputs
12.1 Description........................................................................................................15
12.2 Contact Rating...................................................................................................15
12.3 Model431OutputHarnessWiring.......................................................................16
Annunciator Outputs
13.1 Description........................................................................................................16
13.2 Model300HarnessWiring ..................................................................................16
13.3 Model 860 Relay Module.....................................................................................16
Wireless Bus Expansion
14.1 Description........................................................................................................16
14.2 WirelessBusLEDs .............................................................................................16
LX-BusTM/AX-BusTM Expansion
15.1 LX-Bus HeadersLX-Bus/AX-Bus Headers...............................................................17
15.2 LX-Bus/AX-Bus LEDs ..........................................................................................17
15.3 OVC LEDs..........................................................................................................18
ETHERNET Connector (Panels with Network only)
16.1 Description........................................................................................................18
16.2 Ethernet LEDs ...................................................................................................18
16.3 Network Transient Suppression ...........................................................................18
PHONE LINE RJ Connector
17.1 Description........................................................................................................18
17.2 Phone Line Monitor ............................................................................................18
RESET and TAMPER Headers
18.1 RESET Header ...................................................................................................19
18.2 TAMPER Header.................................................................................................19
Cellular Modules
19.1 CELL MODULE Header........................................................................................20
19.2 Module Installation ............................................................................................20
19.3 Connecting the Antenna .....................................................................................20
International Certications

XR150INT/XR550INT Series Installation Guide Digital Monitoring Products
1
PANEL SPECIFICATIONS
Product Specications Summary
1.1 Power Supply
Transformer Input: Model 324INT wire-in — Primary input: 230 VAC, 50 Hz, Secondary output: 18 VAC 100
VA, 400 mA
Standby Battery: 12 VDC, 1.0 Amps Max. charging current
Models 365, 366, 368, or 369
Replace every 3 to 5 years
Auxiliary: 12 VDC output at 1.5 Amp Max
Bell Output: 12 VDC at 1.5 Amp Max
All circuits are inherent Power Limited except the red battery wire and AC terminal.
1.2 Communication
• Built-in network communication to DMP Model SCS-1R or SCS-VR Receivers
• Built-in Contact ID communication to DMP Model SCS-1R Receivers
• Can operate as a local panel
1.3 Panel Zones
• Eight 1k Ohm EOL/Dual EOL burglary zones (zones 1 to 8)
• Two 3.3k Ohm EOL powered zone with reset (zones 9 and 10)
1.4 Keypad Bus
You can connect up to a total of 16 of the following supervised keypads and expansion modules to keypad
bus:
• Alphanumeric keypads
• One, four, eight, and sixteen-zone expansion modules
• Wireless Keypads (maximum of 7)
1.5 LX500-LX900 Bus™
You can connect the following devices to the LX-Bus™ connections provided on the panel. See Accessory
Devices section 3.3.
• Four, eight, sixteen- and/or single-zone expansion modules
• Relay output expansion modules
• Graphic annunciator modules
1.6 Outputs
The XR150INT/XR550INT Series panels provide two Single Pole, Double Throw (SPDT) relay outputs which
require the installation of two Model 305 relays, each rated 1 Amp at 30 VDC resistive (power limited sources
only).
A Model 431 Output Harness is required to use these outputs.
The XR150INT/XR550INT Series panels also provide four open collector outputs rated for 50mA each. The
open collector outputs provide ground connection for a positive voltage source. A Model 300 Output Harness
is required to use these outputs.

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
2
PANEL SPECIFICATIONS
1.7 Enclosure Specications
The XR150INT/XR550INT Series panels are shipped in an enclosure with a transformer, End-of-Line resistors,
battery leads, user guide, and programming sheets.
Enclosure
Model
Size Color(s) Construction (Cold
Rolled Steel)
350INT 44.45 W x 34.29 H x 8.89 D cm Gray (G) or Red (R) 18-Gauge
350AINT 44.45 W x 34.29 H x 8.89 D cm Gray (G) 18-Gauge with
16-Gauge door
349INT 31.75 W x 29.21 H x 8.89 D cm Gray (G) 20-Gauge
352PINT 36.83 W x 81.28 H x 10.16 D cm Gray (G) 16-Gauge
352XINT 36.83 W x 81.28 H x 10.16 D cm Gray (G) 16-Gauge
Panel Features
2.1 Description
The DMP XR150INT/XR550INT Series system is made up of an alarm panel with a built-in communicator, an
enclosure, battery, one transformer, and keypads. Each panel is a versatile 12VDC, combined access control,
burglary, and re communicator panel with battery backup. The panels provide eight on-board burglary zones
and two on-board 12 VDC Class B powered zones. The powered zones have a reset capability to provide for 2-wire
smoke detectors, relays, or other latching devices. Combined current requirements of additional modules may
require an auxiliary power supply. Refer to the Power Requirements section in this guide when calculating power
requirements. The panels can communicate to DMP SCS-1R Receivers using digital dialer, cellular, network, or
Contact ID communication. Panels using cellular, network, or encrypted communication can also communicate to
DMP SCS-VR Receivers.
2.2 Zone Expansion
Each panel provides multiple options for zone expansion:
• 10 on-board zones
• Up to 64 programmable keypad zones
• Up to 500 LX-Bus zones
Using DMP LCD keypad remote zone capability and zone expansion modules, additional zones are available on each
panel:
• XR550INT provides up to 574 additional zones
• XR150INT provides up to 142 additional zones
The panel keypad data bus supports up to 16 supervised device addresses with each address supporting up to four
programmable expansion zones (64 total).
Using the on board LX-Bus™ connections, and any combination of single, four, eight, or sixteen-zone expansion
modules and single-zone LX-Bus™ detectors, additional zones are available on each panel:
• XR550INT provides up to 500 additional zones (LX500-LX900)
• XR150INT provides up to 100 additional zones (LX500)
Note: Do not use shielded or twisted pair wiring for LX-Bus or Keypad Bus circuits.
2.3 Output Expansion
In addition to the two SPDT relays and four programmable open collector outputs on the XR150INT/XR550INT
Series panels, you can also connect up to 25 programmable Model 716 Output Expansion Modules to each LX-Bus.
These modules can provide an additional 500 or 100 programmable SPDT relays.
The panels provide Output Schedules for programming the 716 to perform a variety of annunciation and control
functions. Also assign the 716 outputs to any panel Output Options such as Fire Alarm, Communication Fail, or
Phone Trouble Outputs. Refer to the 716 Installation Guide (LT-0183).
2.4 Central Station Communication
You can program the panel for reporting to DMP SCS-VR or SCS-1R Receivers using digital dialer, cellular, network,
or Contact ID communication. The panels connect at the premises to a standard RJ31X or RJ38X telephone jack.

XR150INT/XR550INT Series Installation Guide Digital Monitoring Products
3
PANEL SPECIFICATIONS
2.5 Caution Notes
Throughout this guide you will see caution notes containing information you need to know when installing the
panel. These cautions are indicated with a yield sign. Whenever you see a caution note, make sure you completely
read and understand its information. Failing to follow the caution note can cause damage to the equipment or
improper operation of one or more components in the system. See the example shown below.
Always ground the panel before applying power to any devices: The panel must be properly grounded
before connecting any devices or applying power to the panel. Proper grounding protects against Electrostatic
Discharge (ESD) that can damage system components.
2.6 Compliance Instructions
For applications that must conform to a local authorities installation standard or a National Recognized Testing
Laboratory certicated system, please see the Compliance Listing Guide LT-1330INT for additional instructions.

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
4
SYSTEM COMPONENTS
System Components
3.1 Specic and Non-specic Wired Interconnections
The XR150INT/XR550INT Series panels diagram below shows some of the accessory modules you can connect
for use in various applications. A brief description of each module follows in section 3.3.
AC
1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 199 20 21 22 23 24 25 26 27 28
+B BELLGND SMK GNDRED YEL GRN BLK Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9+ Z9– Z10+ Z10–AC –B GND GND GNDGND
Auxiliary Power
Total current combined from terminals
7, 11, 25, 27, XBUS and LX500-LX900
1.5 Amp Max 13.8 VDC to 10.2 VDC
LX800
LX900
J4
Tamper
K6 K7
Output 1 Output 2
J3
Phone Line
Battery
Start
J8
J16
Reset
Out1 Out2
Outputs 3-6
J11
3
4
5
6
J2
OVC
XR550INT Series
International Panel
LX500
LX700
XBUS
J13
J14 J9 J15 J19J17
J24
Form C Relays (J2)
Output Color Code–Model 431 Harness
Output 2 N/O Orange/White
Output 2 Com White/Gray
Output 2 N/C Violet/White
Output 1 N/O Orange
Output 1 Com Gray
Output 1 N/C Violet
Annunciator Outputs (J11)
Output Color Code
Output 3 Red
Output 4 Yellow
Output 5 Green
Output 6 Black
s
s
J12 75VA
50VA
Listed Resistors
1.0k Ohm - DMP Model 311
3.3k Ohm - DMP Model 309
10K Ohm - DMP Model 308
LX600
Tamper
16 to 18 gauge wire
Maximum AC Wire distance
with 16 gauge wire: 70 feet
with 18 gauge wire: 40 feet
RED
BLACK
Cold Water
Pipe Earth
Ground
Bell
3.3k Ohm
Resistor
DMP
Model 309
3.3k Ohm
Resistor
DMP
Model 309
s
= Supervised Circuit
Zone
9
Zone
10
22 gauge minimum 22 gauge minimum 22 gauge minimum
22 gauge minimum
RED
YELLOW
GREEN
BLACK
Zone Expander
Models 714-8INT,
714-16INT
20mA @ 12 VDC
RED
YELLOW
GREEN
BLACK
s
Dual
1k
Ohm
Zone Expander
(up to 8 zones)
Model 712-8INT
19mA @ 12 VDC
1k
Ohm
Earth Ground
s s s s
sss
s
s
s
s
s
s
¼"
AC Wiring must be in conduit and exit
out the left side of the enclosure.
Wiring on terminals 5 through 22 must
exit right and maintain 1/4" separation
from the AC and battery positive wiring.
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
ssssssss
ssssssss
Dual
1k
Ohm
ss
Dual
1k
Ohm
ss
Dual
1k
Ohm
ss
Dual 1k
Ohm
ss
s
Model 324INT 230V 100VA
18 VAC, 50 Hz,
400 mA
CAUTION: DO NOT USE LOOPED WIRE
UNDER TERMINALS. BREAK WIRE RUN
TO PROVIDE SUPERVISION OF
CONNECTIONS.
WARNING: Incorrect
connections may cause
damage to the unit.
Bell cuto time
range is 2 to 15
minutes, non-coded.
Bell
12 VDC
Default cuto time 15 min.
Minimum cuto time 2 min.
1.5 Amp Max
Conduit
INPUT OUTPUT
GROUND
Figure 1: XR550INT Series Wiring Diagram
3.2 Lightning Protection
Metal Oxide Varistors and Transient Voltage Suppressors help protect against voltage surges on panel input and
output circuits. Additional surge protection is available by installing the Model 270 Network Transient Suppression
Module.

XR150INT/XR550INT Series Installation Guide Digital Monitoring Products
5
SYSTEM COMPONENTS
3.3 Accessory Devices
Cellular Communicator Cards
263LTE-INT-A Allows you to connect the XR150INT/XR550INT Series panels to any compatible LTE
network.
Accessory Modules
270INT Network Transient
Suppression Module
Provides transient surge protection for the ETHERNET Connector.
Expansion Modules
710INT Bus Splitter/Repeater Allows you to increase keypad or LX-Bus™ wiring distance to 2500 feet.
714-8INT, 714-16INT Zone Expanders Provides Class B zones for connecting burglary and non-powered re devices.
712-8INT Zone Expander Provides Class B zones for connecting burglary devices.
716INT Output Expander Provides four Form C relays (SPDT) and four switched grounds (open collector) for use in a
variety of remote annunciation and control applications for use on the LX-Bus only.
7 34INT, 734NINT Access Control
Modules
Provides system codeless entry, and arming and disarming using access control readers.
DMP Two-Way Wireless Devices
1100XINT Receiver Supports up to 500/100 devices in residential or commercial wireless operation.
1100RINT Repeater Provides additional range for wireless devices.
1103INT Universal Transmitter Provides both internal and external contacts that may be used at the same time to yield
two individual reporting zones from one wireless transmitter. Requires EOL resistor for
external contact. Provides Disarm/Disable functionality.
1122INT PIR Motion Detector Provides motion detection with pet immunity.
1128INT Wireless Glassbreak Detector Provides fully-supervised, low current shock and glassbreak detection coverage up to 20 ft.
1142BCINT Two-button Hold-up Belt
Clip Transmitter
Provides two-button hold-up operation with a belt clip.
1142INT Two-button Hold-up
Transmitter
Provides permanently mounted under-the-counter two-button hold-up operation.
1144-4INT (Four-Button)
1144-2INT (Two-Button)
1144-1INT (One-Button)
Key Fob transmitters designed to clip onto a key ring or lanyard.
Interface Modules
738Z+INT Z-Wave Interface Module Provides connection for Z-Wave modules.
Indicating and Initiating Devices
860INT Relay Module Provides dry relay contacts that are programmable and controlled from the DMP panel
annunciator outputs. Includes one Form C (SPDT) relay rated 1 Amp @ 30VDC. Sockets are
provided to allow the addition of three Model 305 plug-in relays. These relays can be used
for electrical isolation between the alarm panel and another system or switching 5, 12, or
24 Volts to control various functions within a building or around its perimeter.
Keypads
LCD keypads Allows you to control the panel from various remote locations. Connect up to sixteen Model
7060-WINT, 7063-WINT, 7073-WINT, Thinline™ keypads, or the 7872-WINT and 7873-WINT
Graphic Touchscreen keypads to the keypad bus using terminals 7, 8, 9, and 10.
Wireless keypads Allows you to control the panel from various remote locations. Connect up to seven
9862-WINT Wireless Graphic Keypads.

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
6
INSTALLATION
Installation
4.1 Mounting the Enclosure
The metal enclosure for the XR150INT/XR550INT Series panels must be mounted in a secure, dry place to
protect the panel from damage due to tampering or the elements. It is not necessary to remove the panel
PCB when installing the enclosure. Figure 2 shows the mounting hole locations for the Model 350INT/350AINT
Enclosures. Figure 3 shows the Model 352PINT panel cabinet and 352S shelf cabinet for multiple batteries.
The 350AINT Attack Resistant enclosure is factory shipped with one knockout on the top left of the
enclosure. As needed, additional knockouts or antenna exits may be added at the time of installation. See
Figure 2 for the positions on the enclosure that can be added. Each additional knockout must be lled with
conduit.
Enclosure Mounting Holes
3-Hole
Pattern for
Accessory
Modules
Tamper Switch
for 350A Attack
Resistant
Enclosure
Dual 1 3/4" and 1 3/8" Conduit Knockouts
Battery Shelf holds up to three 7 Ah Batteries
XR550INT Panel
1
AC
2
AC
3
B+
4
B-
5
BELL
6
GND
7
RED
8
YEL
9
GRN
10
BLK
11
SMK
12
GND
13
Z1
14
GND
15
Z2
16
Z3
17
GND
18
G4
19
Z5
20
GND
21
Z6
22
Z7
23
GND
24
Z8
25
Z9+
26
Z9-
27
Z10+
28
Z10-
PROG
RED BLK
J8
LX500
RED BLK
LX600
RED BLK
J14 J9 J15
LX700
RED BLK
LX800
RED BLK
J15
LX900
RED BLK
XMIT
XBUS
RCV
LX
XMIT RCV
700
600
XMIT RCV
XBUS
J13
Output 2
XMIT RCV
500
PROG
XMIT RCV
J8
PROG
K7
OVC
OUTPUTS
LEV
J2
OUT2OUT1
Output 1
K6
LOAD
J16
J7
RESET
J16 EXP
CELL
MODULE
J24
ETHERNET
J1
BATT S TAR T
PWR
50 VA 75 VA
J12
PHONE LINE
J3
BT1
3V
BR2325
* 350A Optional Knockout
*
**
*
*
J6
K
893A
or 277
3
4
5
6
Figure 2: XR550 International Series panel in Model 350 or 350A Enclosure