DMP Electronics XR500N SERIES User manual

INSTALLATION GUIDE
XR500 SERIES
CONTROL PANEL

MODEL XR500, XR500N, XR500E SERIES
CONTROL PANEL INSTALLATION GUIDE
FCC NOTICE
This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance
with the manufacturer’s instructions, may cause interference with radio and television reception. It has been type tested
and found to comply with the limits for a Class A computing device in accordance with the specication in Subpart J
of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential
installation. If this equipment does cause interference to radio or television reception, which can be determined by
turning the equipment o and on, the installer is encouraged to try to correct the interference by one or more of the
following measures:
Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the compute into a dierent outlet so that computer and receiver are on dierent branch circuits
If necessary, the installer should consult the dealer or an experienced radio/television technician for additional suggestions.
The installer may nd the following booklet, prepared by the Federal Communications Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Oce, Washington D.C. 20402
Stock No. 004-000-00345-4
© 2015 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.

XR500 Series Installation Guide Digital Monitoring Products
i
TABLE OF CONTENTS
Product Specications Summary
1.1 Power Supply ......................................................................... 1
1.2 Communication ...................................................................... 1
1.3 Panel Zones ........................................................................... 1
1.4 Keypad Bus............................................................................ 1
1.5 LX-Bus™................................................................................ 1
1.6 Outputs ................................................................................. 1
1.7 Enclosure Specications .......................................................... 1
Panel Features
2.1 Description ............................................................................ 2
2.2 Zone Expansion...................................................................... 2
2.3 Output Expansion................................................................... 2
2.4 Central Station Communication................................................ 2
2.5 Encrypted Communications (XR500N/XR500E only) .................. 2
2.6 Caution Notes ........................................................................ 2
2.7 Compliance Instructions.......................................................... 2
System Components
3.1 Description ............................................................................ 3
3.2 Wiring Diagram ...................................................................... 3
3.3 Lightning Protection................................................................ 4
3.4 Accessory Devices .................................................................. 4
3.4 Accessory Devices (continued) ................................................ 5
3.4 Accessory Devices (continued) ................................................ 6
Installation
4.1 Mounting the Enclosure .......................................................... 6
4.2 Mounting Keypads and Zone Expansion Modules....................... 8
4.3 Connecting LX-Bus and Keypad Bus Devices ............................. 8
4.4 Wireless Keypad Association.................................................... 8
Primary Power Supply
5.1 AC Terminals 1 and 2.............................................................. 9
5.2 Transformer Types.................................................................. 9
5.3 J12 3-Pin Header for Transformer Types................................... 9
Secondary Power Supply
6.1 Battery Terminals 3 and 4 ....................................................... 9
6.2 Earth Ground (GND) ............................................................... 9
6.3 Battery Only Restart ............................................................... 9
6.4 Battery Replacement Period .................................................. 10
6.5 Discharge/Recharge.............................................................. 10
6.6 Battery Supervision............................................................... 10
6.7 Battery Cuto ...................................................................... 10
6.8 XR500 Series Power Requirements......................................... 11
6.9 Standby Battery Selection ..................................................... 13
Bell Output
7.1 Terminals 5 and 6................................................................. 14
Keypad Bus
8.1 Description .......................................................................... 14
8.2 Terminal 7 - RED .................................................................. 14
8.3 Terminal 8 - YELLOW............................................................ 14
8.4 Terminal 9 - GREEN .............................................................. 14
8.5 Terminal 10 - BLACK ............................................................. 14
8.6 J8 Programming Connection.................................................. 14
8.7 OVC LED.............................................................................. 14
Smoke and Glassbreak Detector Output
9.1 Terminals 11 and 12 ............................................................. 14
9.2 Current Rating...................................................................... 14
Protection Zones
10.1 Terminals 13–24................................................................... 15
10.2 Operational Parameters......................................................... 15
10.3 Zone Response Time ............................................................ 15
10.4 Keyswitch Arming Zone......................................................... 15
Powered Zones for 2-Wire Smoke Detectors
11.1 Terminals 25–26 and 27–28 .................................................. 15
11.2 Compatible 2-Wire Smoke Detector Chart............................... 16

Digital Monitoring Products XR500 Series Installation Guide
ii
TABLE OF CONTENTS
Dry Contact Relay Outputs
12.1 Description .......................................................................... 17
12.2 Contact Rating ..................................................................... 17
12.3 Model 431 Output Harness Wiring ......................................... 17
Annunciator Outputs
13.1 Description .......................................................................... 17
13.2 Model 300 Harness Wiring..................................................... 17
13.3 Model 860 Relay Module ....................................................... 17
J23 6-Pin Header
14.1 Description .......................................................................... 18
J22 LX-Bus Expansion Connector
15.1 Description .......................................................................... 18
15.2 J22 LX-Bus Header ............................................................... 18
15.3 LX-Bus Interface Cards ......................................................... 19
15.4 LX-Bus LEDs......................................................................... 19
15.5 OVC LED.............................................................................. 19
J21 Serial Connector
16.1 Description .......................................................................... 19
16.2 Computer Connection to J21 ................................................. 19
16.3 Serial Connector LEDs........................................................... 20
J1 Ethernet Connector (XR500N/XR500E only)
17.1 Description .......................................................................... 20
17.2 Ethernet LEDs ...................................................................... 20
J3 Telephone RJ Connector
18.1 Description .......................................................................... 20
18.2 J10 893A Connector ............................................................. 20
18.3 Notication .......................................................................... 20
18.4 Phone Line Monitor............................................................... 20
18.5 FCC Registration................................................................... 21
Reset and Tamper Headers
19.1 J16 Reset Header ................................................................. 22
19.2 J4 Tamper Header ................................................................ 22
Listed Compliance Specications
20.1 Introduction......................................................................... 23
Universal Burglary Specications
21.1 Introduction......................................................................... 23
21.2 Wiring ................................................................................. 23
21.3 Transformer ......................................................................... 23
21.4 Control Outside of Protected Area.......................................... 23
21.5 Police Station Phone Numbers ............................................... 23
21.6 Bypass Reports .................................................................... 23
21.7 System Maintenance............................................................. 23
21.8 Listed Receivers ................................................................... 23
21.9 Power Supply Supervision ..................................................... 23
21.10 Wireless Tamper................................................................... 23
21.11 Wireless External Contact...................................................... 23
21.12 Wireless Supervision Time..................................................... 23
21.13 Detect Wireless Jamming ...................................................... 23
21.14 Standby Batteries ................................................................. 23
Area Information
22.1 Ownership ........................................................................... 24
22.2 Annunciation........................................................................ 24
22.3 Trouble Display..................................................................... 24
22.4 Closing Wait......................................................................... 24
22.5 Local Bell Supervision ........................................................... 24
Household Burglar-Alarm System Units
ANSI/UL 1023
23.1 Audible Devices.................................................................... 24
23.2 Auxiliary Circuits................................................................... 24
23.3 Bell Cuto............................................................................ 24
23.4 Entry Delay.......................................................................... 24
23.5 Exit Delay ............................................................................ 24
23.6 Weekly Test ......................................................................... 24
23.7 Wireless Audible Annunciation Option .................................... 24

XR500 Series Installation Guide Digital Monitoring Products
iii
TABLE OF CONTENTS
Central-Station and Proprietary Burglar-Alarm Units
ANSI/UL 1610 AND ANSI/UL 1076
24.1 Opening/Closing Reports....................................................... 25
24.2 Closing Wait......................................................................... 25
24.3 Entry Delay.......................................................................... 25
24.4 Exit Delay ............................................................................ 25
24.5 Proprietary Dialer ................................................................. 25
24.6 DACT Central Station ............................................................ 25
24.7 Bell Cuto............................................................................ 25
24.8 Standard or Encrypted Line Security ...................................... 25
24.9 Wireless Audible Annunciation Option .................................... 25
24.10 CELL Only, Standard or Encrypted Line Security...................... 25
24.11 NET with CELL as Alternate Primary and Dialer Backup,
Standard or Encrypted Line Security ...................................... 26
24.12 NET with CELL as Backup and Adaptive Primary, Standard
or Encrypted Line Security .................................................... 26
Holdup Alarm Units
ANSI/UL 636
25.1 ANSI/UL 1610 Required ........................................................ 27
25.2 1100X/1100XH Wireless Receiver........................................... 27
25.3 Wireless Supervision Time..................................................... 27
25.4 LED Display.......................................................................... 27
25.5 Jamming Detection............................................................... 27
25.6 Local Alarm.......................................................................... 27
25.7 Message to Transmit............................................................. 27
25.8 Wireless Audible Annunciation Option .................................... 27
Digital Burglar Alarm Communicator System Units
ANSI/UL 1635
26.1 System Trouble Display ......................................................... 27
26.2 Digital Dialer Telephone Number............................................ 27
26.3 Test Time............................................................................. 27
26.4 Closing Wait......................................................................... 27
Police Station Connected and Local Burglar Alarm Units
ANSI/UL 365
27.1 System Trouble Display ......................................................... 27
27.2 Entry Delay.......................................................................... 27
27.3 Exit Delay ............................................................................ 27
27.4 Bell ..................................................................................... 28
27.5 Bell Cuto............................................................................ 28
27.6 Automatic Bell Test ............................................................... 28
27.7 Standard or Encrypted Line Security ...................................... 28
27.8 Wireless Audible Annunciation Option .................................... 28
27.9 Model 463C, CELL Only, Standard or Encrypted Line Security... 28
27.10 Model 463C, NET with CELL as Alternate Primary and
Dialer Backup, Standard or Encrypted Line Security ................ 29
27.11 Model 463C, NET with CELL as Backup and Adaptive Primary,
Standard or Encrypted Line Security ...................................... 29
Police Station Connected and Local Burglar Alarm Units
ANSI/UL 609
28.1 Mercantile............................................................................ 30
28.2 Entry Delay.......................................................................... 30
28.3 Exit Delay ............................................................................ 30
28.4 Mercantile Safe and Vault...................................................... 30
28.5 Bell ..................................................................................... 30
28.6 Bank Safe and Vault (XR500N/XR500E only)........................... 30
28.7 Wireless Audible Annunciation Option .................................... 30
Access Control System Units
ANSI/UL 294
29.1 Panel Designation................................................................. 31
29.2 Tamper Protection ................................................................ 31
29.3 Transformer ......................................................................... 31
29.4 Compatible Devices .............................................................. 31

Digital Monitoring Products XR500 Series Installation Guide
iv
TABLE OF CONTENTS
Universal Fire Alarm Specications
30.1 Introduction......................................................................... 31
30.2 Wiring ................................................................................. 31
30.3 Transformer ......................................................................... 31
30.4 End-of-Line Resistor.............................................................. 31
30.5 System Trouble Display ......................................................... 31
30.6 Fire Display.......................................................................... 31
30.7 Police Station Phone Number................................................. 32
30.8 System Maintenance............................................................. 32
30.9 Audible Alarm....................................................................... 32
30.10 Fire Zone Programming......................................................... 32
30.11 Class A Style D Zones ........................................................... 32
30.12 Listed Receivers ................................................................... 32
30.13 Standby Batteries ................................................................. 32
Control Units for Fire-Protective Signaling Systems
ANSI/UL 864, NFPA 72
31.1 Power Supply ....................................................................... 33
31.2 Zone Restoral Reports........................................................... 33
31.3 Power Fail Delay................................................................... 33
31.4 Sprinkler Supervisory ............................................................ 33
31.5 DACT Systems...................................................................... 33
31.6 Local Protective Signaling Systems......................................... 33
31.7 Remote Station Protective Signaling Systems.......................... 34
31.8 Fire Protective Signaling Systems using
Internet/Intranet/Cell Networks............................................. 34
31.9 Combination Systems ........................................................... 34
31.10 Remote Annunciators............................................................ 34
31.11 Notication Appliances.......................................................... 35
31.12 Cross Zoning ........................................................................ 35
31.13 Ground Fault ........................................................................ 35
31.14 Wireless Testing ................................................................... 35
31.15 Wireless Supervision............................................................. 35
Household Fire Warning System Units
ANSI/UL 985, NFPA 72
32.1 Bell Output Denition............................................................ 35
32.2 Audible Devices.................................................................... 35
32.3 Auxiliary Circuits................................................................... 35
32.4 Bell Cuto............................................................................ 35
32.5 Detect Wireless Jamming ...................................................... 35
32.6 Wireless Supervision Time..................................................... 35
32.7 Wireless Fire Verication ....................................................... 35
California State Fire Marshal Specications
33.1 Bell Output Denition............................................................ 35
New York City (FDNY) Specications
34.1 Introduction......................................................................... 36
34.2 Network and Cellular Communication, Primary and Secondary . 36
34.3 Digital Dialer Primary and Network Secondary Communication. 36
34.3.1 Communication Programming................................................ 36
34.4 Wiring ................................................................................. 36
34.5 Additional Requirements ....................................................... 36
False Alarm Reduction Programmable Options *
35.1 Shipping Defaults and Recommended Programming
for ANSI/SIA CP-01-2010 ...................................................... 37
False Alarm Reduction Programmable Options (continued)
35.2 Call Waiting.......................................................................... 38
35.3 Occupied Premise................................................................. 38
35.4 Entry Delay.......................................................................... 38
35.5 Minimum Installation Requirements ....................................... 38
Wiring Diagrams
36.1 866 with NAC Extender ......................................................... 39
36.2 866 Class B Style W using Single Notication Appliance........... 40
36.3 866 Class B Style W Multiple Notication Appliance Circuit....... 41
36.4 866 Class B Style W Dual Notication Appliance Circuits .......... 42
36.5 865 Class B Style W using Single Notication Appliance........... 43
36.6 865 Class B Style W Multiple Notication Appliance Circuit....... 44
36.7 865 Class B Style W Dual Notication Appliance Circuits .......... 45

XR500 Series Installation Guide Digital Monitoring Products
v
TABLE OF CONTENTS
36.8 865 Class A Style X using Single Notication Appliance............ 46
36.9 867 Class B Style W using Single Notication Appliance........... 47
36.10 867 Class B Style W Multiple Notication Appliance Circuit....... 48
36.11 867 Class B Style W Multiple Notication Appliance Circuits ..... 49
36.12 Panel Slave Communicator for FACP using 630F Annunciator ... 50
36.13 Panel Slave Communicator for FACP using Outputs ................. 51
36.14 Dual Style D Zone Module Installation.................................... 52
36.15 Derived Channel Installation Using Bosch D8122 .................... 53
36.16 Rothenbuhler 5110 High Security Bell Wiring..................... 54
36.17 LX-Bus™ Module Connection ................................................. 55
36.18 Model 860 Relay Module Connection ...................................... 56
36.19 Powered Burglary Devices ..................................................... 56
36.20 System Sensor 2-Wire Smoke Detectors................................. 57
36.21 System Sensor i4 Series Smoke and CO Detectors
Using A Single COSMOD2W Module ....................................... 58
36.22 System Sensor i4 Series Smoke and CO Detectors
Using Multiple COSMOD2W Modules ...................................... 59
Revisions to This Document
Certications
Export Control

This page intentionally left blank

XR500 Series Installation Guide Digital Monitoring Products
1
INTRODUCTION
Product Specications Summary
1.1 Power Supply
Transformer Input: Model 327, plug-in — Primary input: 120 VAC, 60 Hz, Secondary output: 16.5 VAC 50 VA
Model 322/323, wire-in — Primary input: 120 VAC, 60 Hz, Secondary output: 16 VAC 56 VA
Model 324/324P, wire-in — Primary input: 120 VAC, 60 Hz, Secondary output: 16 VAC 100 VA
Standby Battery: 12 Vdc, 1.0 Amps Max. charging current
Models 364, 365, 366, 368, or 369
Replace every 3 to 5 years
Auxiliary: 12 Vdc output at 1.5 Amp Max*
12 Vdc output at 325mA used with two Model 364 batteries in the Model 341 enclosure
Bell Output: 12 Vdc at 1.5 Amp Max*
All circuits are inherent Power Limited except the red battery wire and AC terminal.
* For Commercial Burglary and Fire installations, see the Compliance Instructions section. See section 5.3 J12
3-Pin Header for Transformer Types for panel output 2 Amp or 3 Amp current limitations.
1.2 Communication
• Built-in network communication to DMP Model SCS-1R or SCS-VR Receivers (XR500N/XR500E only)
• Built-in encrypted communication to DMP Model SCS-1R Receivers (XR500E only)
• Built-in dialer communication to DMP Model SCS-1R Receivers
• Optional cellular communication to DMP Model SCS-1R or SCS-VR Receivers
• Built-in Contact ID communication to DMP Model SCS-1R Receivers
• Optional 893A Dual Phone Line Module with phone line supervision
• Can operate as a local panel
1.3 Panel Zones
Eight 1k Ohm EOL burglary zones (zones 1 to 8)
Two 3.3k Ohm EOL powered zone with reset (zones 9 and 10)
1.4 Keypad Bus
You can connect up to a total of 16 of the following supervised keypads and expansion modules to the keypad bus:
• Alphanumeric keypads • Four- and/or single-zone expansion modules
• Single-zone detectors • Access control modules
• Wireless Keypads (maximum of 4)
1.5 LX-Bus™
You can connect the following devices to the LX-Bus™ provided on the panel or by the DMP 481, 462N, 462P, 463C
464-263C and 464-263H Interface Cards up to the maximum number of LX-Bus™ addresses. See Accessory Devices in
section 3.4.
• Sixteen-, eight-, four- and/or single-zone expansion modules • Graphic annunciator modules
• Model 521LX or 521LXT Smoke Detectors with CleanMe • Relay output expansion modules
• Model 2W-BLX or 2WT-BLX Smoke Detectors
1.6 Outputs
The XR500 Series provide two Single Pole, Double Throw (SPDT) relay outputs which require the installation of two
Model 305 relays, each rated 1 Amp at 30 Vdc resistive (power limited sources only). A Model 431 Output Harness is
required to use these outputs.
The XR500 Series panels also provide four open collector outputs rated for 50mA each. The open collector outputs
provide ground connection for a positive voltage source. A Model 300 Output Harness is required to use these
outputs.
1.7 Enclosure Specications
The XR500 Series panels are shipped in an enclosure with a transformer, End-of-Line resistors, battery leads, user’s
guide, and programming sheets.
Enclosure
Model
Size Color(s) Construction (Cold Rolled
Steel)
350 17.5”W x 13.5”H x 3.5”D Gray (G) or Red (R) 18-Gauge
350A 17.5”W x 13.5”H x 3.75”D Gray (G) 18-Gauge with 16-Gauge door
341 12.75”W x 6.55”H x 3.15”D Gray (G) 20-Gauge
352X 14.5”W x 32.0”H x 4.0”D Gray (G) 16-Gauge

Digital Monitoring Products XR500 Series Installation Guide
2
INTRODUCTION
Panel Features
2.1 Description
The DMP XR500 Series panel is a versatile 12 Vdc, combined access control, burglary, and re communicator panel
with battery backup. The XR500 Series provides eight on-board burglary zones and two on-board 12 Vdc Class B
powered zones. The powered zones have a reset capability to provide for 2-wire smoke detectors, relays, or other
latching devices. The XR500 Series can communicate to DMP SCS-1R or SCS-VR Receivers using digital dialer, cellular,
network, or Contact ID communication.
2.2 Zone Expansion
Up to 574 additional zones are available on the XR500 Series using DMP LCD keypad remote zone capability and zone
expansion modules. The panel keypad data bus supports up to sixteen supervised device addresses with each address
supporting up to four programmable expansion zones.
Up to 500 zones are available using the on board LX-Bus, Model 461 Interface Adaptor with 481, 462N, 462P, 463C,
464-263C and 464-263H Interface Cards, and any combination of single, four, eight, or 16-zone expansion modules
and single-zone LX-Bus™ detectors.
Note: Do not use shielded wire for LX-Bus or Keypad Bus circuits.
2.3 Output Expansion
In addition to the two SPDT relays and four programmable open collector outputs on the XR500 Series, you can also
connect up to 25 programmable Model 716 Output Expansion Modules to each LX-Bus. These modules can provide an
additional 500 programmable SPDT relays.
The XR500 Series provides 100 Output Schedules for programming the 716 to perform a variety of annunciation and
control functions. Also assign the 716 outputs to any panel Output Options such as Fire Alarm, Communication Fail,
or Phone Trouble Outputs. Refer to the 716 Installation Guide (LT-0183).
The LX-Bus™ also supports the Model 717 Graphic Annunciator Module. Each 717 module supplies 20 switched ground
outputs that follow the state of their assigned zones.
Note: The 717 supports the rst eight Keypad Bus addresses. To follow Keypad Bus addresses nine through 16, install
multiple 716 modules. Refer to the 717 Installation Guide (LT-0235) and 716 Installation Guide (LT-0183).
2.4 Central Station Communication
You can program the XR500 Series panel for reporting to DMP SCS-1R or SCS-VR Receivers using digital dialer, cellular,
network, or Contact ID communication. The XR500 Series connects at the premises to a standard RJ31X or RJ38X
telephone jack. Use the DMP 893A Dual Phone Line Module when connecting the XR500 Series panel to two separate
phone lines in re or burglary applications.
2.5 Encrypted Communications (XR500N/XR500E only)
An XR500E panel communicates using AES encryption. If you currently have an XR500N panel installed, you may
contact DMP Customer Service with the panel serial number. The serial number(s) should be sent in writing via
e-mail or fax. A separate feature key is sent for each panel to activate encrypted communications using the Feature
Upgrade process. Encrypted communication cannot be enabled on a standard XR500 panel. For more information on
the Feature Upgrade process see the XR500 Series Programming Guide (LT-0679).
2.6 Caution Notes
Throughout this guide you will see caution notes containing information you need to know when installing the panel.
These cautions are indicated with a yield sign. Whenever you see a caution note, make sure you completely read
and understand its information. Failing to follow the caution note can cause damage to the equipment or improper
operation of one or more components in the system. See the example shown below.
Always ground the panel before applying power to any devices: The XR500 Series must be properly
grounded before connecting any devices or applying power to the panel. Proper grounding protects against
Electrostatic Discharge (ESD) that can damage system components.
2.7 Compliance Instructions
For applications that must conform to a local authorities installation standard or a National Recognized Testing
Laboratory certicated system, please see the Wiring Diagrams for Notication Appliances and the Listed Compliance
Specications section near the end of this guide for additional instructions.