DMP Electronics 630F Installation guide

POWER
TROUBLE
ALARM
COMMAND
1234
5678
90
ABC DEF GHI JKL
MNOPQR STUVWX
YX
ENABLE
SILENCE
RESET
TEST
DRILL
Fire Command Center
INSTALLATION AND PROGRAMMING GUIDE
630F Remote Fire
Command Center

About the 630F ..................................................... 1
Four Function Keys.............................................................1
Status LEDs............................................................................1
Keyswitch................................................................................1
Install the 630F..................................................... 2
Mount the Backbox............................................................2
Mount and Wire the Membrane Backplate...............4
Mount the Trim Frame ......................................................4
Command Center operation ............................... 6
Command Center Operation..........................................6
Programming........................................................................6
Device Setup ........................................................................6
Device Number....................................................................6
Device Name ........................................................................7
Device Type ..........................................................................7
Stop..........................................................................................7
End-User Options ............................................... 10
Backlighting Brightness.................................................10
Internal Speaker Tone .....................................................10
Internal Volume Level ...................................................... 11
Model Number .................................................................... 11
Keypad Address................................................................. 11
Entering Alpha Characters.................................12
Entering Non-Alphanumeric Characters..........13
TABLE OF CONTENTS
Installer Options Menu........................................14
Access the User Menu.....................................................14
Programming Keypad Options.................................... 14
Keypad Options (KPD OPT)......................................... 14
Keypad Address ............................................................... 15
Keypad Mode .................................................................... 15
Default Keypad Message .............................................. 16
Arm Panic Keys ................................................................ 16
Stop ...................................................................................... 16
Access Keypad Diagnostics.......................................... 17
Keypad Diagnostics (KPD OPT) ................................. 17
Stop ...................................................................................... 17
Exit the Installer Options............................................... 18
Keypad Bus Wiring Specifications....................19
630F Specifications ...........................................20
Compatibility .......................................................21
Certifications....................................................... 22
California State Fire Marshal (CSFM)....................... 22
FCC Part 15......................................................................... 22
New York City (FDNY COA #6167)........................... 22
Underwriters Laboratory (UL Listed)...................... 22

POWER
TROUBLE
ALARM
COMMAND
1234
5678
90
ABC DEF GHI JKL
MNOPQR STUVWX
YX
ENABLE
SILENCE
RESET
TEST
DRILL
Fire Command Center
Figure 1: 630F Remote Fire Command Center

Digital Monitoring Products, Inc. | 630F Installation and Programming Guide 1
The 630F Remote Fire Command Center is a 20-key remote fire annunciator with a
32-character LCD display that can be either flush or surface mounted.
Four Function Keys
The 630F includes four function keys
allowing the user to easily silence, reset,
test, and fire drill XR150/XR550 Series
panels.
Status LEDs
The 630F provides three LEDs that indicate
system status.
Keyswitch
An added 630F feature is a keyswitch that
enables and disables the four function keys.
In order for the function keys to operate,
the factory-installed keyswitch must be
enabled. These functions and options can
also be accessed through the User Menu if
desired.
ABOUT THE 630F

2 630F Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 630F
Mount the Backbox
The 630F can either be surface mounted or flush mounted to the wall. The 630F is
comprised of three major parts: the backbox (standard or optional surface mount
635), the annunciator membrane backplate, and the trim frame. Refer to Figure 2 as
needed.
Flush Mount the Backbox
Use four 1” screws and the mounting holes on one side of the flush mount backbox
to attach the backbox to a stud. The backbox tab flush-mounts against the stud. See
Figure 2.
For post-sheetrock installation, the flush mount backbox should be mounted flush
against the sheetrock and then attached to the stud behind using the flush mounting
holes.
Surface Mount the Backbox
The optional 635 Low-Profile Backbox can be used for surface mount applications.
Use four 1” screws to attach the backbox to the wall and screw one screw in each of
the four surface mounting holes in the back of the box.
Note: The 4-hole pattern in the surface mount backbox also fits a 4” square
electrical box to allow mounting on an electrical box.
1

Digital Monitoring Products, Inc. | 630F Installation and Programming Guide 3
Slotted Screw Holes (4)
Use 3/8” Countersunk Phillips Screws
to Fasten to Backbox Screw Holes
Screw Holes (4)
Screw Holes (4)
Use 3/8” Black Phillips Screws
to Fasten to Backplate Screw Holes
Screw Holes (4)
Backbox
Stud
Membrane Backplate Trim Frame
Surface Mounting Holes (4)
Use to Surface Mount to Wall
Knockout
Tab
Flush Mounting Holes (4)
Use to Flush Mount to Stud
1. Mount the Backbox 2. Mount the Membrane Backplate 3. Mount the Trim Frame
Figure 2: Mounting Diagram

4 630F Installation and Programming Guide | Digital Monitoring Products, Inc.
Mount and Wire the Membrane Backplate
Refer to Figure 2 for locations of knockouts on backbox for running wires and screw
holes on backbox and backplate.
1. Connect a four conductor wire from the 630F backplate terminal strip to
panel terminals 7, 8, 9, and 10. See Figure 3.
2. Attach the annunciator membrane backplate (slotted screw holes) to the
backbox using the four supplied countersunk 3/8” Phillips screws.
3. Adjust the mounting plate to the right or left so the LCD display is level.
The four slotted screw holes in the mounting plate corners allow for this
adjustment.
2
Mount the Trim Frame
Attach the trim frame to the mounting plate using the four supplied 3/8” black
Phillips screws. See Figure 2.
3

Digital Monitoring Products, Inc. | 630F Installation and Programming Guide 5
Back of Membrane Backplate
4 Position
Terminal Strip
4-Pin
Header
Pre-wired
Keyswitch
Black to 10
Green to 9
Yellow to 8
Red to 7
Figure 3: Harness Wiring Diagram

6 630F Installation and Programming Guide | Digital Monitoring Products, Inc.
COMMAND CENTER OPERATION
Command Center Operation
• INTERNAL SPEAKER OPERATION—The speaker emits standard tones for key
presses and system alerts and distinct fire siren tones during an alarm.
• LCD BACKLIGHTING—lights to maximum brightness anytime a key is pressed or
the speaker sounds.
Programming
After completing each of the following steps, press CMD to advance to the next option.
Programming
Reset the panel and enter 6653 (PROG) at a keypad.
Device Setup
Go to DEVICE SETUP.
Device Number
At DEVICE NO, enter a device number.
For Keypad Bus connections, select a device number from 1-8
for XR150 panels or 1-16 for XR550 panels.
PROGRAMMER
DEVICE SETUP
DEVICE SETUP
DEVICE NO: -