DMP Electronics XTLN-WiFi User manual

INSTALLATION GUIDE
XTLN-WIFI PANEL

MODEL XTLN-WiFi
INSTALLATION GUIDE
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe
user’s authority to operate the equipment.
This device has been designed to operate with the integrated 1100 Series PCB antenna having a maximum
gain of 1.8 dB. Antennas having a gain greater than 1.8 dB are strictly prohibited for use with this device.
The required antenna impedance is 50 ohms.
If necessary, the installer should consult the dealer or an experienced radio/television technician
foradditionalsuggestions.Theinstallermayndthefollowingbooklet,preparedbytheFederal
Communications Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
ThisbookletisavailablefromtheU.S.GovernmentPrintingOfce,WashingtonD.C.20402
StockNo.004-000-00345-4
©2013DigitalMonitoringProducts,Inc.
InformationfurnishedbyDMPisbelievedtobeaccurateandreliable.
This information is subject to change without notice.

XTLN-WiFi Installation Guide Digital Monitoring Products
i
TABLE OF CONTENTS
Panel Specications
1.1 Power Supply .........................................1
1.2 Communication.......................................1
1.3 Keypads .................................................1
1.4 Number of Zones ....................................1
1.5 EnclosureSpecications ..........................1
Introduction
2.1 SystemCongurations.............................1
2.2 Caution Notes.........................................1
2.3 Compliance Instructions ..........................1
System Components
3.1 Accessory Devices...................................2
Installation
4.1 MountingLocationInformation ................3
4.2 MountingtheEnclosure...........................3
Primary Power Supply
5.1 DC Input ................................................3
Secondary Power Supply
6.1 Standby Battery......................................4
6.2 Replacement ..........................................4
6.3 Battery Supervision .................................4
LED Operation
7.1 BacklitLogo............................................5
On-Board WiFi Network
8.1 Description.............................................5
8.2 WiFiLEDs...............................................5
Reset Button
9.1 Description.............................................5
Programming Connection
10.1 ProgrammingConnection ........................5
On-Board 1100 Series Wireless
11.1 Wireless Antenna ....................................5
11.2 WirelessLEDOperation ...........................5
Keypads
12.1 MountingKeypads ..................................6
12.2 InstallationSpecications ........................6
12.3 Wireless Keypad Association ....................6
Wireless Zones
13.1 Description.............................................6
Wireless Key Fobs and Outputs
14.1 Description.............................................6
Flash Load Button
15.1 Description ............................................7
Listed Compliance Specications
16.1 Introduction ...........................................7
16.2 UseMarking ...........................................7
16.3 NFPA 72.................................................7
16.4 TypesOfService .....................................7
16.5 Bypass Reports.......................................7
16.6 Battery Standby......................................7

Digital Monitoring Products XTLN-WiFi Installation Guide
ii
TABLE OF CONTENTS
Household Burglar-Alarm System Units
ANSI/UL 1023
17.1 Bell Cutoff ..............................................7
17.2 Entry Delay ............................................7
17.3 Exit Delay...............................................7
17.4 Wireless External Contact ........................7
17.5 Wireless Supervision Time .......................7
17.6 Wireless Audible Annunciation .................8
17.7 Panel location .........................................8
17.8 Test Frequency .......................................8
Central Station Burglar Alarm Units
ANSI/UL 1610
18.1 Supervision ............................................8
18.2 Remote Disarm.......................................8
18.3 Central Station........................................8
Household Fire Warning System
ANSI/UL 985 NFPA 72 Specications
19.1 BellOutputDenition ..............................8
19.2 HouseholdSystem ..................................8
19.3 Wireless External Contact ........................8
19.4 Wireless Supervision Time .......................8
19.5 Test Frequency .......................................8
19.6 Wired Modules........................................8
Listings and Approvals.......................... 10

XTLN-WiFi Installation Guide Digital Monitoring Products
1
PANEL SPECIFICATIONS
Panel Specications
1.1 Power Supply
Input:   12VDC
StandbyBattery: 3.7VDCLithium
All circuits inherent power limited
1.2 Communication
Built-innetworkcommunicationtoDMPModelSCS-1RorSCS-VRReceivers.
1.3 Keypads
Youcanconnectupto4alphanumeric7800SeriesGraphicTouchscreenKeypadsor9000SeriesWireless
Keypads.
1.4 Number of Zones
• XTLN-WiFihas28wirelessinitiatingzonesnumbered1-28
• ZoneandOutputnumbers31to34and41to44cansupport1100SeriesKeyFobs,OutputModules,
or sirens
1.5 Enclosure Specications
TheXTLN-WiFipanelshipsinaplasticenclosurewithauser’sguideandprogrammingsheet.
Size Color
5.5”Wx3.75”Hx1”D White(W)
Introduction
2.1 System Congurations
The panel can be programmed to operate as any of the following system types:
• All/Perimetersystemthatprovidesoneperimeterareaandoneinteriorarea
• Home/Sleep/Awaysystemthatprovidesoneperimeter,oneinterior,andonebedroomarea.The
bedroom area provides for any protection devices the user wants disarmed during their sleeping hours
and armed in the Away mode.
• Sixareasystemthatprovidesareasofprotectionthatcanbeindependentlyarmedordisarmed.
2.2 Caution Notes
Throughoutthisguideyouwillseecautionnotescontaininginformationyouneedtoknowwheninstalling
thepanel.Thesecautionsareindicatedwithayieldsign.Wheneveryouseeacautionnote,makesureyou
completely read and understand its information. Failing to follow the caution note can cause damage to the
equipment or improper operation of one or more components in the system.
2.3 Compliance Instructions
ForapplicationsthatmustconformtoalocalauthoritiesinstallationstandardoraNationalRecognized
TestingLaboratorycerticatedsystem,pleaseseetheListedComplianceSpecicationssectionneartheend
of this guide for additional instructions.
INTRODUCTION

Digital Monitoring Products XTLN-WiFi Installation Guide
2
SYSTEM COMPONENTS
System Components
3.1 Accessory Devices
DMP Two-Way Wireless Devices
1100R Repeater Provides additional range for wireless devices.
1101UniversalTransmitter Provides both internal and external contacts that may be used at the same time to yield two
individualreportingzonesfromonewirelesstransmitter.
1102UniversalTransmitter Provides one external contact.
1103UniversalTransmitter Provides both and internal and external contacts that may be used at the same time to
yieldtwoindividualreportingzonesfromonewirelesstransmitter.RequiresEOLresistorfor
external contact.
1105UniversalTransmitter Provides both internal and external contacts that may be used at the same time to yield two
individualreportingzonesfromonewirelesstransmitter.
*1107MicroWindowTransmitter Provides a wireless window transmitter
*1114Four-ZoneExpander ProvidesfourwirelesszoneswithEOLresisters.
*1116RelayOutput Provides one Form C relay.
*1117LEDAnnunciator Provides a visual system status indicator.
*1119DoorSounder Provides a wireless sounder with integrated door contact
*1121PIRMotionDetector Provides motion detection with pet immunity.
1125PIRMotionDetector Providesmultiplelenscongurations,dualcoverageareaselection,andsensitivityadjustments.
*1126C/1126R/1126WPIRMotion
Detector
CeilingmountmotiondetectorwithpanelprogrammablesensitivityandDisarm/Disable
functionality.
1127C/1127WPIRMotion
Detector
WallmountmotiondetectorwithpanelprogrammablesensitivityandDisarm/Disable
functionality.
*1129GlassbreakDetector Detectstheshatteringofframedglassmountedinanoutsidewallandprovidesfull-pattern
coverage and false-alarm immunity.
*1131RecessedContact Provides concealed protection for doors, windows or other applications.
1135/*1135DBWirelessSirens Provides a wireless siren
*1139BillTrap Provides a silent alarm option for use in cash drawers.
1142BCTwo-buttonPanicBelt
Clip Transmitter
Provides portable two-button panic operation.
1142Two-buttonPanicTransmitter Provides permanently mounted under-the-counter two-button panic operation.
*1145-4(Four-Button)
*1145-2(Two-Button)
*1145-1(One-Button)
KeyFobtransmittersdesignedtoclipontoakeyringorlanyard.
1161ResidentialSmokeDetector Residentialsmokedetectorwithsounder.
1162ResidentialSmokeDetector Residentialsmoke/heatdetectorwithsounderandxedrate-of-riseheatdetector.
1183-135FHeatDetector Fixed temperature heat detector
1183-135RHeatDetector Fixed temperature and rate-of-rise heat detector
*1184CarbonMonoxideDetector CarbonMonoxidedetector.
Interface Module
*738ZZ-WaveInterfaceModule ProvidesconnectionforZ-Wavemodules.
Keypads
7800SeriesLCDkeypads Allowsyoutocontrolthepanelfromvariousremotelocations.Connectuptofour7872or
7873keypadstothekeypadbususingterminals7,8.9,and10.
9000SeriesLCDkeypads Allowsyoutocontrolthepanelfromvariousremotelocationsusing9000SeriesWireless
Keypads.
* These devices have not been investigated and shall not be used in listed installations

XTLN-WiFi Installation Guide Digital Monitoring Products
3
INSTALLATION
Installation
4.1 Mounting Location Information
A location should be selected that is centrally located between the 1100 Series transmitters used in the
installation.InstalltheXTLN-WiFiawayfrommetalobjects.MountingtheXTLN-WiFionornearmetal
surfacesimpairsperformance.Whenselectingthepropermountinglocationofatransmitter,refertothe
LEDSurveyOperationsectionofthespecicinstallationguideforthetransmitterbeinginstalled.
4.2 Mounting the Enclosure
TheenclosurefortheXTLN-WiFipanelmustbemountedusingtheprovided#6screwsinthefourmounting
holesshowninFigure2.Mounttheenclosureinasecure,dryplaceawayfrommetalobjectstoprotect
thepanelfromdamageduetotamperingortheelements.Mountthepanelaminimumof4feetfromany
wireless transmitters or repeaters. It is not necessary to remove the PCB when installing the enclosure.
Mounting Hole Locations
WiFi Network
Module
Figure 1: Mounting Hole Locations
Primary Power Supply
5.1 DC Input
MounttheXTLN-WiFipanelnearawalloutletfortheModel372-500plug-inDCpowersupply.Inaddition
topoweringthepanel,theDCplug-inpowersupplyalsochargestheback-upbattery.The372-500mustbe
locatedwithin100feetofthepanelusing22AWGwire.Usethefollowingstepstoconnecttheplug-inpower
supply:
OBSERVE POLARITY
1.Using22AWGwire,connectthepanelPWR(J2)rstterminal(+)tothepositiveterminalonthe
power supply.
2.ConnectthepanelPWR(J2)secondterminal(-)tothenegativeterminalonthepowersupply.
3.Plugthepowersupplyintoa120VoltAC,60Hzdedicatedoutletnotcontrolledbyaswitch.
Wire Exits for DC
Power Supply
+
Model 372-500
DC Plug-in
Power
Supply
Use 22 AWG for
Power Supply connection
_
J2
Figure 2: DC Power Supply Connection

Digital Monitoring Products XTLN-WiFi Installation Guide
4
INSTALLATION
Secondary Power Supply
6.1 Standby Battery
TheXTLN-WiFirechargeablebatteryisusedtoprovidebackupbatterypowerwhenDCpowerisnot
available.ThebatteryisintendedforbackuppoweronlyandnottooperatetheXTLN-WiFipanelonadaily
basis.Ifthebatteryislow,ornotpluggedintotheJ7batteryconnector,alowbatteryconditionisindicated
bytheXTLN-WiFipanel.
Note:IfremovingtheXTLN-WiFipanelfromservice,disconnectthebackupbatteryfromtheXTLN-WiFiJ7
connector.
6.2 Replacement
UsethefollowingstepstoreplacetheXTLN-WiFistandbybattery.DMPrecommendsreplacingthebattery
every3yearsundernormaluse.
1. Unplugthebatteryconnector(J7)fromtheXTLN-WiFipanel.
2. Ifinstalled,removethescrewfromthePCB.
3. LoosenthetopPCBsnaps.
4. LeanthepanelPCBforwardandliftoutfromthebottomPCBsnaps.
5. Remove and properly dispose of the used battery.
 Caution:Riskofre,explosion,andburns.Donotdisassemble,heatabove212°F(100°C),
or incinerate. Properly dispose of used batteries.
6. PlacethenewbatteryintotheXTLN-WiFihousingbasewiththebatterywiresdirectedtowardthe
bottomrightcorner.SeeFigure4.
7. SettheXTLN-WiFiPCBintothebottomsnapsandpressintothetopsnapstosecureinplace.
8. Plugthebatteryintothepanelconnector(J7).
6.3 Battery Supervision
ThepanelteststhebatteryonceeveryhourwhenDCpowerispresent.Thistestoccurs15minutespast
eachhourandlastsforveseconds.Aloadisplacedonthebatteryandifthebatteryvoltageislow,alow
batteryisdetected.IfDCpowerhasfailed,alowbatteryisdetectedanytimethebatteryvoltagefalls
below3.7V.
PCB Screw Location
Top PCB Snaps
Bottom PCB Snaps Battery
connector
3.7V
Rechargeable
Battery
Figure 4: Standby Battery ReplacementFigure 3: PCB Screw Location

XTLN-WiFi Installation Guide Digital Monitoring Products
5
INSTALLATION
LED Operation
7.1 Backlit Logo
ThebacklitlogoindicatesthePowerandArmedstatusofthepanel.Dependingontheoperation,theLED
displaysinRedorGreenaslistedinthetable.
Color and Activity Operation
GreenSteady PanelDisarmed,PrimaryPowerOK,BatteryOK
GreenBlinking PanelDisarmed,PrimaryPowerOK,BatteryFault
NoLight PanelDisarmed,PrimaryPowerFault,BatteryOK
Red Steady PanelArmed,PrimaryPowerOK,BatteryOK
Red/GreenAlternate PanelArmed,PrimaryPowerOK,BatteryFault
RedBlinking PanelArmed,PrimaryPowerFault,BatteryOK
On-Board WiFi Network
8.1 Description
TheXTLN-WiFiconnectsdirectlytoaWiFinetworkforencryptedTCPcommunicationusingaWireless-B/G
connection.TheXTLN-WiFiuseswireless802.11b/gWiFitechnology,whichcantravel125ft.indoorsandcan
reachoutto460ft.outdoorswithaclearlineofsight.
Note:RangeforWiFicommunicationhasnotbeeninvestigatedbyUL.
8.2 WiFi LEDs
ThetwoWiFiLEDs,locatedinthecenterofthecircuitboard,indicatenetworkoperation.TheleftWiFi-1
LEDisagreenlightthatissolidwhenthenetworkisconnectedandblinksonandoffwhenthereisno
networkconnectivity.TherightWiFi-2LEDisayellowlightandblinkswhenmessagesarebeingreceivedor
transmitted.
Reset Button
9.1 Description
Theresetbutton(S1)islocatedontherightsideofthecircuitboardandisusedtoresettheXTLN-WiFi
microprocessor. To reset the panel prior to reprogramming, press the reset button without powering down
thesystem.Afterresettingthepanel,beginprogrammingwithin30minutes.Ifyouwaitlongerthan30
minutes, you must reset the panel again.
Programming Connection
10.1 Programming Connection
Alocking4-pinheader(PROG)isprovidedtoconnectakeypadwhenusingaDMPModel330Programming
Cable.ThisprovidesaquickandeasyconnectionforprogrammingtheXTLN-WiFipanel.Afterprogramming
iscomplete,removethekeypad.
On-Board 1100 Series Wireless
11.1 Wireless Antenna
TheXTLN-WiFiWirelessAntennaisintegratedintothecircuitboard.TheXTLN-WiFibuilt-inwirelessreceiver
operateswithDMP1100Seriestransmitters.Seesection3.1foralistofaccessorydevices.
11.2 Wireless LED Operation
Green (TX):ThegreenLEDasheseverytimethereceivertransmits(32timespersecond).Ifthepanel
isreset,orthepanelispoweredoff,thegreenLEDisoff.Undernormaloperation,thegreenLEDashes
constantly with no interruption or change.
Yellow (RX):TheyellowLEDasheseverytimetheXTLN-WiFireceivesamessagefromaprogrammed
wirelesstransmitter.Whenamessageissentbyatransmitter,typicallybypressingorreleasingthetamper
switch,theyellowLEDshouldashindicatingthattheXTLN-WiFireceivedamessagefromthetransmitter.
IftheLEDneverashes,thetransmitterisnotgettingthroughtotheXTLN-WiFi.Thiscouldbebecause
ofamisprogrammedserialnumberorthetransmitteristoofaraway.Undernormaloperation,theyellow
LEDashesateverytripofeverywirelesstransmitterandwhenthetransmittersperformtheirperiodic
check-in.ItisnotunusualforthisLEDtostayoffformanyminutesatatimewhennotransmittersare
communicating.

Digital Monitoring Products XTLN-WiFi Installation Guide
6
INSTALLATION
Keypads
12.1 Mounting Keypads
DMPkeypadshaveremovablecoversthatallowthebasetobemountedonawall,deskstandorotherat
surface using the screw holes provided on each corner.
12.2 Installation Specications
Severalfactorsdeterminetheperformancecharacteristicsofthekeypadbus:thelengthofwireused,the
numberofdevicesconnected,andthevoltageateachdevice.Whenplanningakeypadbusinstallation,
keepinmindthefollowingfourspecications:
1. DMPrecommendsusing18or22-gaugeunshieldedwireforallkeypadcircuits.Donotusetwisted
pairorshieldedwireforkeypadbusdatacircuits.
2. Onkeypadbuscircuits,tomaintainauxiliarypowerintegritywhenusing22-gaugewiredonot
exceed500feet.Whenusing18-gaugewiredonotexceed1,000feet.Toincreasethewirelength
or to add devices, install an additional power supply.
 Note:Eachpanelallowsaspecicnumberofsupervisedkeypads.Addadditionalkeypadsinthe
unsupervisedmode.Refertothepanelinstallationguideforthespecicnumberofsupervised
keypadsallowed.
3. Maximumdistanceforanyonebuscircuit(lengthofwire)is2,500feetregardlessofthewire
gauge. This distance can be in the form of one long wire run or multiple branches with all wiring
totalingnomorethan2,500feet.Aswiredistancefromthepanelincreases,DCvoltageonthe
wire decreases.
4. Maximumvoltagedropbetweenthepanel(orauxiliarypowersupply)andanydeviceis2.0VDC.If
the voltage at any device is less than the required level, add an auxiliary power supply at the end
ofthecircuit.Whenvoltageistoolow,thedevicescannotoperateproperly.
Foradditionalinformationrefertothe710InstallationSheet(LT-0310)andortheLX-Bus/KeypadBusWiring
ApplicationNote(LT-2031).
12.3 Wireless Keypad Association
EnableWirelessKeypadAssociationoperationonboththekeypadandpanel.
Toenableassociationoperationinthekeypad,accesstheInstallerOptionsMenu(3577(INST)CMD).The
keypadlogoLEDsturnoffuntilassociationissuccessful.
Toenableassociationoperationinthepanel,presstheXTLN-WiFiRESETbutton3timeswithin12seconds
allowing3secondsbetweeneachpressoftheresetbutton.Wheninkeypadassociation,theXTLN-WiFiRed
andGreenlogoLEDsturnonsteady.
For60secondsthepanellistensforwirelesskeypadsthatareintheInstallerOptionsMenu(3577CMD)and
havenotbeenprogrammed,orassociatedintoanotherpanel.Thosekeypadsareassignedtotherstopen
devicepositionautomaticallybasedupontheorderinwhichtheyaredetected.ThekeypadlogoturnsGreen
to indicate it has been associated with the panel.
Wireless Zones
13.1 Description
XTLN-WiFipanelsprovide28wirelesszonesnumbered1to28.Adefaultzonename,zonetype,andarea
assignmentaredescribedintheXTLN-WiFiProgrammingGuide(LT-1237)andcanbechangedinZone
Information programming as needed. The defaults are provided as a programming convenience to help
reduce installation time.
Wireless Key Fobs and Outputs
14.1 Description
XTLN-WiFipanelsprovide8wirelesskeyfoboroutputaddressesnumbered31to34and41to44.Adefault
name is provided as a programming convenience to help reduce installation time. The default names are
describedintheXTLN-WiFiProgrammingGuide(LT-1237)andcanbechangedinOutputInformationorZone
Information programming as needed.

XTLN-WiFi Installation Guide Digital Monitoring Products
7
INSTALLATION
Flash Load Button
15.1 Description
TheXTLN-WiFipanelsoftwarecanbeupdatedviathepanel’sprogramming(PROG)header.Toupdatethe
panel with a new software version, complete the following steps at the protected premise:
1. ConnectaDMP399CablefromtheProgrammingHeadertotheserialportofyourPCoperating
RemoteLinkandcontainingtheXTLN-WiFiRemoteUpdatele.
2. StartRemoteLinkandcreateoropentheXTLN-WiFicontrolpanelaccountthatmatchesthepanel
to be updated.
3. SettheConnectionInformationTypetoDirectwithabaudrateof38400andchoosethe
appropriateCOMport.
4. SelectPanel>RemoteUpdate,thenselectthecorrectRUlefortheXTLN-WiFipanel.
5. PressandholdtheLOADbutton(S2),thenpressandreleasetheRESETbutton.
6. ReleasetheLOADbuttonandclick<Update>inRemoteLink.
7. Afterthesoftwareupdateiscompleted,removethe399cableandpresstheRESETbuttonto
resume normal panel operation.
Listed Compliance Specications
16.1 Introduction
Theprogrammingandinstallationspecicationscontainedinthissectionmustbecompletedwheninstalling
theXTLN-WiFiinaccordancewithanyoftheANSI/ULorSIAburglarystandards.Additionalspecicationsmay
be required by a particular standard.
16.2 Use Marking
CommercialCentralStation,HouseholdBurglarandFireControlUnit.
16.3 NFPA 72
ThisequipmentshouldbeinstalledinaccordancewithChapter11oftheNationalFireAlarmCode,ANSI/
NFPA72-2002,(NationalFireProtectionAssociation,BatterymarchPark,Quincy,MA02269).Printed
information describing proper installation, operation, testing, maintenance, evacuation planning, and repair
serviceistobeprovidedwiththisequipment.Warning:Owner’sinstructionnotice,nottoberemovedby
anyone except occupant.
16.4 Types Of Service
SuitableforCentralStation.SuitableforHouseholdFireandHouseholdBurglary.Testweekly.
16.5 Bypass Reports
ThebypassreportsmustbeprogrammedasYESforalllistedburglaryapplications.
16.6 Battery Standby
TheXTLN-WiFiisshippedwithabatteryfor24hourbatterystandbyoperation.
Household Burglar-Alarm System Units
ANSI/UL 1023
17.1 Bell Cutoff
Thebellcutofftimecannotbelessthan4minutes.
17.2 Entry Delay
Themaximumentrydelayusedmustnotbemorethan45seconds.
17.3 Exit Delay
The maximum exit delay used must not be more than 60 seconds.
17.4 Wireless External Contact
Whenused,theExternalContactof1101,1102,or1105transmittersmustbeprogrammedNormallyClosed.
17.5 Wireless Supervision Time
TheZoneInformationSupervisionTimecannotbesetto0(zero).

Digital Monitoring Products XTLN-WiFi Installation Guide
8
INSTALLATION
17.6 Wireless Audible Annunciation
TheWirelessAudibleoptionmustbeselectedasDAYforresidentialapplications.
17.7 Panel location
Mountpanelinsideprotectedarea.
17.8 Test Frequency
TheTestFrequencyoptionmustbeprogrammedtosendareportatleastonceevery30days.
Central Station Burglar Alarm Units
ANSI/UL 1610
18.1 Supervision
CommercialBurglaryisprovidedwhentheCellCheck-inandFailTimetimeissetto3minutes.
Note:TheSecureComWirelesstextplanselectedforthepanelshouldmatchorexceedtheprogrammed
MonthlyLimitoradditionalcellularchargesmayapply.
18.2 Remote Disarm
REMOTEDISARMmustbeprogrammedasNO.
18.3 Central Station
MESSAGETOTRANSMITprogrammingforzonesmustnotbesettoLOCAL(L).
Household Fire Warning System
ANSI/UL 985 NFPA 72 Specications
19.1 Bell Output Denition
ThewirelesssirenoftheXTLN-WiFipanelmustbeprogrammedtooperatesteadyonburglaryalarmsand
temporalonrealarms.SeetheXTLN-WiFiProgrammingGuide(LT-1237).
19.2 Household System
An alarm sounding device must be installed indoors so that it is clearly heard in all sleeping areas.
19.3 Wireless External Contact
Whenused,theExternalContactof1101,1102,or1105mustbeprogrammedNormallyClosed.Seethe
XTLN-WiFiProgrammingGuide.
19.4 Wireless Supervision Time
TheZoneInformationSupervisionTimemustbe3minutesforredevices.SeetheXTLN-WiFiProgramming
Guide.
19.5 Test Frequency
TheTestFrequencyoptionmustbeprogrammedtosendareportatleastonceevery30days.
19.6 Wired Modules
ModulesthatconnecttothePROGheader,suchasthe738Z,mustnotbeusedsincethebatterystandby
timewillbereducedbelowthe24hourminimum.

Thispageintentionallyleftblank

LT-1236 1.01 © 2013 Digital Monitoring Products, Inc.
800-641-4282
www.dmp.com
Designed,Engineeredand
AssembledintheUSA
INTRUSION•FIRE•ACCESS•NETWORKS
2500NorthPartnershipBoulevard
Springfield,Missouri65803-8877
13225
Listings and Approvals
ANSI/SIACP-2010FalseAlarmReduction
FCCWiFiModuleApprovals
FCCID:XM5-SM2144SMT
IndustryCanada:8516A-SM2144SMT
FCCWirelessApprovals
FCCPart15ID:CCKPC0117
IndustryCanada:5251A-PC0117
UnderwritersLaboratories(UL)Listed
 ANSI/UL985 HouseholdFireWarning
 ANSI/UL1023 HouseholdBurglar
 ANSI/UL1610 CentralStationBurglar