DNP ID+ User manual
ID+
ID photo solution
Installation and Quick Start Guide
Exclusively for DNP ID600 printer
and dedicated ID600 media
Mars 2019
ID+ solution Installation and Quick Start Guide v.1.0
2
Version 1.0
ID+ solution Installation and Quick Start Guide v.1.0
3
Warning Chapter 1
To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.
To avoid electrical shock, do not open the ID+ Tablet and ID600 Printer covers. Refer servicing to qualified
staff only.
THIS EQUIPMENT MUST BE EARTHED.
To disconnect the main power, unplug the AC IN connector.
Read before use
Review the user guide before using system. Go to http://www.dnpphoto.eu/en/
For each device contained in this system, see “Important Safety Instructions” in the corresponding user guides
or start-up guides.
Use a proper power cord for your local power supply.
Tablet
1. Use the original Power Brick and Cord provided in the tablet box / Appliance Connector / Plug with earthing-
contacts that conforms to the safety regulations of each country if applicable.
Printer
2. Use the Power Cord (3-core mains lead) / Appliance Connector / Plug conforming to the proper ratings
(Voltage, Ampere).
EU compliance statements
This system is compliant with Class A of EN55032. This system is not intended for residential area. In a residential
area this system may cause radio interference.
The symbol means that according to local laws and regulations your product and/or its battery shall
be disposed of separately from household waste. When this product reaches its end of life, take it to
a collection point designated by local authorities. For details, contact to your dealer.
About ID+ Tablet
Do not attempt to replace the battery yourself –you may damage the battery, which could cause overheating,
fire and injury. The lithium-ion battery in your device should be serviced or recycled by authorized service
provider, and must be recycled or disposed of separately from household waste. Dispose of batteries according
to your local environmental laws and guidelines. For details, contact to your dealer.
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Hereby, PiPO TECHNOLOGY CO., LTD. declares that the radio equipment type PiPO W1 pro is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.dnpphoto.eu/en/support-and-downloads/declaration-conformity
Frequency band in which the radio equipment operates: 2402-2480Hz (BLE), 2412-2472Hz (Wi-Fi).
Maximum radio-frequency power transmitted in the frequency band in which the radio equipment operates:
- 3.1 dBm (BLE), 10.62 dBm (Wi-Fi).
The manufacturer of this product is PiPO TECHNOLOGY CO., LTD. Area C, 3F, Warehouse Building, Bao Yun Da
Logistics Center, Xi Xiang Avenue, Bao an District, Shenzhen, China.
The importer for RE directive and RoHS is DNP PHOTO IMAGING EUROPE SAS, ZI PARIS NORD II, 22 AVENUE DES
NATIONS, PARC SILIC –VILLEPINTE, 95948 ROISSY, CDG CEDEX, FRANCE.
ID+ solution Installation and Quick Start Guide v.1.0
4
Installation Chapter 2
Box content
The box contents:
ID+ Tablet
Keyboard
Digital pen + AAAA 1.5v battery
USB cable
AC adapter
OTG cable
Make sure all power supply cables (Printer and Tablet) are connected. Now, please connect the tablet to the
printer with the USB cable provided in the printer box.
Installation:
ID+ solution Installation and Quick Start Guide v.1.0
5
Quick Start Chapter 3
Note : Please note that the screen can be disconnected from the keyboard and used as a tablet.
Starting ID+ solution
1) Switch on the ID600 printer.
2) Load ID600 media into the printer (please refer to ID600 Start-up Guide).
3) Switch on the ID+ tablet (Switch ON button is on the top left side).
After a few minutes the ID+ Software will automatically start running.
Note:
If the ID600 Printer is not connected, the software will display a message
informing that the printer is disconnected.
You can still proceed the order (start the process until the Print Page). Your order will be saved
automatically in “Pending orders”.
When the printer is connected to the system, a green icon will appear automatically on the top right
of the screen within a few seconds and indicate the remaining prints. Then, you can resume your
order and print.
ID+ solution Installation and Quick Start Guide v.1.0
6
Make an ID photo order
This is the Workflow of creating and printing an ID photo.
1) Select New ID
2) Select where images are located.
3) Select the source.
ID+ solution Installation and Quick Start Guide v.1.0
7
4) Take the photo and validate.
5) Choose the country and the type of document. Select Biometric for automatic process or Manual for
manual editing.
6) You get the biometric results. If necessary, you can edit manually the picture, by clicking on edit
photo.
ID+ solution Installation and Quick Start Guide v.1.0
8
7) Select the options.
Note : Please note that the “send by email”, “save ID to USB” and “ANTS” are deactivated by
default. You can activate these options via the admin settings.
ANTS option is only for France (process specific to French regulations).
8) Insert Customer name.
9) Press “finish” to finish the order.
ID+ solution Installation and Quick Start Guide v.1.0
9
Shutdown the ID+ solution
1) Enter into Main Panel by touching in sequence the lower left and right corners of the monitor.
2) Click on Computer shutdown button
3) Wait until ID+ tablet automatically switches OFF
4) Switch off the ID600 printer.
5) Disconnect power cables.
Table of contents
Other DNP Printer manuals
