Dogtra PT10U User manual

1
PATHFINDER MINI
PT10U, PM10U
SMARTER WAY TO TRACK & TRAIN FOR SMALLER DOGS
Owner's Manual
Please read this manual thoroughly
before operating the Dogtra PATHFINDER MINI.

2
IMPORTANT SAFETY AND PRODUCT
INFORMATION
WARNING
Please read all safety and product information below before using your
Dogtra product. Failure to follow these safety instructions could result in
injury to you, your dog and others, or it could result in damage to your
Dogtra product or other property.
DOG SAFETY
Proper Use
Dogtra products should be used to train, educate, monitor, or track dogs. Each
dog may have a different tolerance for and reaction to Dogtra products. Closely
observe your dog when determining the right level of stimulation, receiver fit,
and other settings of your Dogtra product.
Training Methods
Dogtra products may be used with a variety of training methods that provide
clear and consistent messages to your dog.
Fit and Wear
Proper fit and wear of your Dogtra product is important for the comfort of
your dog as well as the functioning of your product. Dogtra receivers should
fit comfortably and not too tightly, so that the receiver stays in place and does
not move around your dog’s neck. Do not leave a receiver on your dog for an
extended time. Although each dog is different, Dogtra recommends that its
receivers be used a maximum of 4 to 6 hours at any one time on your dog. A
receiver that is used for overly long periods or that fits improperly may cause
skin irritation or sores on your dog’s neck. Regularly check the receiver's contact
area on your dog’s skin. If your dog exhibits skin irritation or sores, stop using
the Dogtra product and consult with a veterinarian.
UNAUTHORIZED USE
Dogtra products should be used only in a safe and responsible manner to train,
educate, monitor, or track dogs. Dogtra products are not intended for use in any
other manner; they are not intended for use with other animals or with humans;
and they are not intended for use in unsafe situations or environments that
could lead to death, injury, loss or damage.
BATTERY
Your Dogtra product contains batteries. Do not attempt to replace the battery
yourself. Contact Dogtra or your Dogtra retailer to replace your battery. Dispose
of batteries as provided by your local regulations. Do not disassemble, crush,
heat, or otherwise alter the battery as it may cause fire, explosion, injury and/or
property damage.

3
OWNER SAFETY
Handling and Repair
Dogtra products can be damaged or malfunction if dropped, especially on
hard surfaces, or otherwise improperly handled. Do not use a damaged or
malfunctioning product as it may cause injury or property damage. If your
product is damaged or malfunctions, contact Dogtra to obtain service before
using the product.
Electrical Product
Your Dogtra product contains electrical components and batteries. Do not use
or keep your product near heat or flammable sources. Such use or storage may
damage your product and/or cause fire, explosion, injury, or property damage.
Charging
Only charge your Dogtra product with its accompanying Dogtra charger. Do
not attempt to charge your product in any other manner or in temperatures
less than 32°F (0°C) or over 113°F (45°C) as it may cause fire, explosion, injury,
and/or property damage. If you notice damage to your product, its charger, or
battery, obtain service from Dogtra before charging the product. Do not use
more than one splitter cable with a single battery charger.
Medical Device Interference
Dogtra products contain electrical and magnetic components that emit low
level electromagnetic waves and radio frequencies. These electromagnetic
waves or radio frequencies may interfere with pacemakers, defibrillators, or
other medical devices. Consult your physician or medical device maker before
using your medical device with a Dogtra product. If you think that your Dogtra
product is interfering with your pacemaker, defibrillator, or other medical
device, stop using the Dogtra product.
Aggressive Dogs
Do not use Dogtra products with aggressive dogs as such dogs may react
adversely and cause injury to people or other dogs. Seek the assistance of a
dog-training specialist or veterinarian when dealing with aggressive dogs.
Children
Dogtra products are not toys. Adult supervision and close attention are
necessary when Dogtra products are used by or near children.

4
PACKAGE CONTENTS ...........................................................................................
MAIN FEATURES ....................................................................................................
OVERVIEW ...............................................................................................................
UNDERSTANDING YOUR TRAINING SYSTEM
TURNING THE PATHFINDER MINI ON/OFF ..............................................
BUTTON FUNCTION ........................................................................................
CHARGING THE PATHFINDER MINI ............................................................
LED INDICATOR ...............................................................................................
INSTALLING THE PATHFINDER MINI APP .................................................
PAIRING ..............................................................................................................
ACQUIRING GPS SIGNAL ...............................................................................
WEB MANUAL DOWNLOAD .........................................................................
CHANGING THE CONTACT POINT LENGTH ...................................................
RECEIVER FITTING ................................................................................................
FINDING THE RIGHT STIMULATION .................................................................
REPLACING THE ANTENNA ................................................................................
MAXIMIZING THE DISTANCE ..............................................................................
ATTACHING THE BELT CLIP ................................................................................
USING THE TEST LIGHT ........................................................................................
APPLICATION
MAP TAB .............................................................................................................
DOG ICONS ........................................................................................................
DOG ALERTS .....................................................................................................
COMPASS TAB ..................................................................................................
E-COLLAR TAB .................................................................................................
DEVICE DETAILS ..............................................................................................
BASIC MAINTENANCE ..........................................................................................
TROUBLESHOOTING GUIDE ...............................................................................
FCC WARNING ........................................................................................................
WARRANTY AND REPAIR INFORMATION .....................................................
CONTENTS
5
6
7
9
10
11
12
13
14
15
16
17
18
19
20
21
21
22
23
24
25
26
27
30
31
32
33
34
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
3.
4.
5.
6.

5
PACKAGE CONTENTS
Test Light Contact Point
Extension Washer/
Adjustment Tool
GPS Connector
(PT10U)
Battery ChargerPATHFINDER MINI:
GPS Receiver
(PM10U)
Splitter Cable Owner’s Manual Belt Clip
Non-Stimulation
Contacts

6
MAIN FEATURES
2-Second GPS
Update Rate
Beacon &
Locate LED Light
Offline Maps
Precise and
Up-to-Date Maps
Geo-Fence Option4-Mile Range
Expandable to
21 Dogs
Fully Waterproof
Belt Clip
2.5-Hour Rapid
Charge Batteries
2s
21
Audible Tone
Enhanced
Contact Points TONE
Low-High Output in
1-100 Stimulation Levels
Nick/Constant
Stimulation
C
NH
4-Mile

7
OVERVIEW
PATHFINDER MINI
GPS Connector (PT10U)
Battery Charging
Receptacle
Power & Select
Button
Connect
Button
MURS Band
Antenna

8
PATHFINDER MINI
GPS Receiver (PM10U)
Battery Charging
Receptacle
Receiver Strap
GPS Antenna
MURS Band
Antenna
Black
Antenna
Casing
Contact
Points
Power
Button
Beacon &
Locate LED
Light
Mic. Sensor

9
UNDERSTANDING YOUR TRAINING SYSTEM
1. TURNING THE PATHFINDER MINI ON/OFF
GPS Connector (PT10U)
• To turn on the GPS connector, press
the blue Select button until the LED
turns on.
• To turn off the GPS connector, press
the blue Select button until the red
LED shows.
GPS Receiver (PM10U)
• To turn on the GPS receiver, press the
Power button until the LED turns on.
• To turn off the GPS receiver, press the
Power button until the LED turns red.
• A tone will play to indicate that the
GPS receiver is turning on or shutting
down.

10
2. BUTTON FUNCTION
GPS Connector (PT10U)
The Select button is used to turn the
connector on/off and select a device to
pair. While turned on, press the Select
button to Phone or Collar to pair the
connector to the respective device.
The Connect button is used to connect
the GPS connector to a smartphone
and GPS receiver.
Pairing: Use the Select button to set
the GPS connector to Collar to pair the
connector with the receiver. Set the
GPS connector to Phone to pair the
connector to a smartphone.
Press and hold down the Connect
button until the LED blinks rapidly.
The GPS connector will now be ready
for pairing.
GPS Receiver (PM10U)
Power On: To turn the GPS receiver on,
press the Power button until the green
LED turns on.
Power Off: To turn the GPS receiver off,
press the Power button until the LED
turns off.
Pairing: To place the GPS receiver into
pairing mode, begin with the device
turned off and hold down the Power
button until the LED blinks rapidly.
A melody will play when the GPS
receiver is in pairing mode.
* The GPS Collar pairing mode is used to pair the GPS receiver and the GPS
connector. The PATHFINDER MINI set comes with both parts paired to each
other.

11
3. CHARGING THE PATHFINDER MINI
Fully charge the PATHFINDER MINI GPS connector and GPS receiver before the
first use. The PATHFINDER MINI uses lithium polymer batteries.
• Only use official Dogtra chargers with the PATHFINDER MINI.
• Do not charge the PATHFINDER MINI near flammable substances.
• Fully charge the PATHFINDER MINI if storing for 1 month or longer.
When to Charge
• When the LED is red on the GPS connector or GPS receiver.
• When the PATHFINDER MINI app displays a low battery percentage for the
GPS connector or GPS receiver.
• When the LED on the transmitter or receiver will not come on.
• When the indicator light turns on momentarily, but will not stay on when the
Constant button is pressed.
How to Charge
1. Connect the charger to the GPS connector and GPS receiver using the splitter
cable.
2. Plug the charger into a 120-volt outlet.
3. When fully charged, detach the cables and plug the rubber caps over the
charging ports on the GPS connector and GPS receiver.
4. The GPS receiver turns off and cannot be used while charging. The GPS
connector functions while being charged. The LED will display red while
charging and green when the unit is fully charged. The GPS connector LED
will be green when turned on while charging. A depleted battery requires 2.5
hours to fully charge.

12
GPS Receiver (PM10U)
The LED on the GPS receiver blinks
while turned on, and the LED colors
represents the battery life: Green when
50-100% battery, Orange when 10-50%
battery, Red when 0-10% battery.
4. LED INDICATOR
GPS Connector (PT10U)
Power: The Power LED blinks every 2
seconds while turned on. The LED colors
represents the battery life: Green when
50-100% battery, Orange when 10-50%
battery, Red when 0-10% battery.
Phone: When turned on, press the
Select button to set the GPS connector
to Phone. When set to Phone, a green
LED will stay on. Hold down the
Connect button until the LED blinks
rapidly to place the GPS connector into
pairing mode.
Receiver: When turned on, press the Select button to set the GPS connector
to Collar. When set to Collar, a green LED will stay on. Hold down the Connect
button until the LED blinks rapidly to place the GPS connector into pairing mode.
Splitter Cable
Do not use more than one splitter cable with a single battery charger.

13
Compatible Phones
1) iOS: iOS 9.1 and above
iPhone 5 series and above
iPad Generation 3 and above
2) Android: Android 4.3 and above
Samsung Galaxy S4 and above, Note 2 and above, and LG G3
Downloading the App
Search for Dogtra PATHFINDER in the App Store or in Google Play.
5. INSTALLING THE PATHFINDER MINI APP
iOS App Store Android Google Play Store

14
6. PAIRING
Pairing a Smartphone to the GPS Connector
1) Launch the PATHFINDER app
2) Turn on the GPS connector
3) In the PATHFINDER app, navigate to Menu →Settings →Bluetooth Pairing
4) Set the GPS connector to pairing mode and click search in the app
• Once paired, launching the app when the GPS connector is on will
automatically connect the phone and connector together.
• The GPS connector should be within Bluetooth range (33 feet) of your phone
to operate.
• The GPS connector will reconnect with the phone when it is within range.
• Reinstalling the app will require pairing with the GPS connector.
• The PATHFINDER app may need to be restarted for compatibility issues.
Pairing Additional GPS Receivers
Pair the GPS connector and GPS receiver in close proximity to each other.
You can use the PATHFINDER app to check if the GPS receiver is properly
paired.
1) Turn the GPS connector on.
2) Check that the GPS receiver is turned off.
3) Use the Select button on the GPS connector to set the LED to Collar.
4) Hold down the connect button for 5 seconds until the LED blinks rapidly.
Release the button.
5) Hold down the Power button on the GPS receiver until the LED blinks rapidly
and emits three beeps to show it has coded.
6) The GPS connector and receiver will return to blinking in normal intervals
when pairing is complete.
PATHFINDER MINI GPS connector connects between your smartphone and
PATHFINDER MINI GPS receiver. These devices need to be paired for the
PATHFINDER MINI system to work properly.
Smartphone
Bluetooth
Max 33 Ft.
MURS Band
Max 4 Miles
PATHFINDER
GPS Connector (PT10U)
PATHFINDER MINI
GPS Receiver (PM10U)

15
The PATHFINDER MINI is meant for use in open outdoor areas. After pairing,
take the GPS receiver outdoors to acquire a GPS signal. Once the signal is
acquired, the GPS receiver icon will appear on the Map tab of the PATHFINDER
app.
Operating the PATHFINDER MINI near tall buildings and other steel structures
will reduce the range of the GPS signal. Not acquiring a GPS signal for prolonged
periods of time while outside may indicate issues with the unit.
7. ACQUIRING GPS SIGNAL

16
8. WEB MANUAL DOWNLAD
In the app, check the PATHFINDER MINI Web Manual at the bottom of the Menu
to see all the app features, such as:
• Map Features
• Marker
• History Record, File, Detail
• Device List Options
• Device Sharing & Receiving
• Map Management: Offline & Custom Map
• Geo-fence
• App Setting
From your computer, check out the manual at www.DogtraPATHFINDER.com
for a full version of the PATHFINDER MINI manual, Q&A, and more.

17
The Dogtra PATHFINDER MINI comes equipped with standard 5/8” contact
points that can be extended to 3/4” contact points, for use on dogs with longer
coats.
To increase the contact point length from 5/8” to 3/4”, follow the steps below.
1) Using the included adjustment tool with the side marked 5/8”, unscrew the
contact points counter-clockwise.
2) Place the contact point extension over the exposed threads, flat side down.
3) Place the contact points over the extensions and tighten the contact
points and extensions clockwise using the adjustment tool with the
side marked 3/4”.
Caution!
Tighten until firmly in place. Be careful not to over tighten.
To shorten the contact points back to the standard 5/8”, start with the
adjustment tool with the side marked 3/4”, remove the contact point
extensions, and tighten the contact points with the adjustment tool with the
side marked 5/8”.
CHANGING THE CONTACT POINT LENGTH

18
Proper Fit
The receiver should be fitted so that the medical grade stainless steel contact
points press firmly against the dog’s skin. You should be able to fit two fingers
underneath the collar strap. The best location is on either side of the dog’s
windpipe.
Improper Fit
A loose fit can allow the receiver to move around on the dog’s neck. When this
happens, the contact points may rub against the skin and cause irritation. If the
receiver is too loose, the contact will not be consistent and cause the corrections
to be inconsistent. Dogtra uses medical grade stainless steel contact points and
anti-microbial plastic to protect the dog’s skin.
Attention!
Leaving the receiver in the same location on the dog’s neck for an extended
period of time can cause skin irritation due to the sensitivity from the contact
points. If the dog is to wear the receiver for long periods, occasionally
reposition the receiver every few hours so that the contact points are moved
to a different location on the dog’s neck and remove the receiver after 8
hours of usage. Make sure you check for skin irritation each time you use the
unit.
RECEIVER FITTING

19
FINDING THE RIGHT STIMULATION
• Open the PATHFINDER app to the E-Collar tab and select your dog and
stimulation level.
• The stimulation levels are from 1 (lowest) to 100 (highest).
• Always start at the lowest level of stimulation and work your way up.
• The appropriate level can be found when your dog responds to the stimulation
with a mild reaction, such as a tensing of the neck muscles.
Note: Every dog has a different tolerance and reaction to the stimulation. Please
look at your dog’s reaction to find the right level of stimulation. The stimulation
level may vary depending on the situation and distractions. A distracted dog will
require a higher level of stimulation compared to when there is no distraction.

20
For the GPS Connector
1. Twist the antenna counter-clockwise to remove.
2. Place the new antenna on the bolt and turn clockwise to tighten the antenna.
REPLACING THE ANTENNA
Open the antenna enclosure by removing the 3 screws and the contact points.
Remove the screw holding the antenna in place to replace the antenna.
For the Receiver