DogWatch GroundsKeeper User manual

The GroundsKeeper® is designed for small applications such as
driveway openings, gardens, patios, decks, and play sets - any
area you want to prevent your pet from entering.
Important Safeguards
•Please read the DogWatch Owner’s Guide before starting
installation and training.
•Keep the receiver collar and transmitter out of reach of children.
•Never adjust the transmitter while your pet is wearing the
receiver collar.
•Unplug the transmitter when the system is left unused for
extended periods.
•Mount the transmitter indoors or in a dry location.
Operating Instructions for the
DogWatch GroundsKeeper

Adjusting the Collar
Collar tightness is critical. All contact points must touch your dog’s
skin in order to receive a correction. A loose collar will also allow
the contact posts to rub back and forth on the skin, possibly causing
irritation. Use care as over-tightening the contact posts could cause
damage to the receiver.
We recommend that the receiver collar be removed each day to
allow your dog’s skin to gradually condition itself to the contact posts
and avoid potential skin irritation, possible infections and pressure
sores.
Installation
The boundary wire allows you to create a specific boundary area
within your yard (see Figures 1 and 2). The wire carries a harmless
radio signal which will activate the receiver your pet is wearing. Your
DogWatch dealer will help you plan and install your boundary areas.
Figures 1 and 2 how how a
garden or a driveway can be
made off bounds to your pet.
Transmitter
Figure 1
Figure 2
Cancelled
signal due
to twisted
wire
Boundary
area with
active signal
eld
Transmitter

Features
Ground Connection. The green ground wire from the power supply
is plugged into the transmitter at the location labeled “GND”. The
ground will only be eective if your outlet is properly grounded. If
you have any questions about a properly grounded outlet, consult
your electrician.
Wire Connections. In order for the system to work properly, the
boundary wire must form a continuous loop. Strip and connect
one end of the boundary wire to one of the terminal connections
labeled “WIRE”. After you create your boundary area, twist the two
wires together as you proceed from the boundary area back to the
transmitter. Twisting the two wires together eliminates the radio
signal in that section of the wire (see Figures 1 and 2). Now strip
and connect the other end of your wire to the other terminal. Any
break in the wire will cancel the signal field. If the boundary wire is
broken or the system is unplugged, the green lights(s) will go out
and an audible warning will sound.
Range. The transmitter emits a coded radio signal through up to 500
feet of boundary wire. You can adjust the distance that the signal
radiates o the boundary wire by turning the knob labeled “- +” with
a common screwdriver. To increase”+” the range, turn clockwise. To
to decrease “-” the range, turn counter clockwise. Always test the
signal field before allowing your pet near the avoidance area. Never
adjust the transmitter while your pet is wearing the receiver collar.
Indicator Lights and Break Alert. After your boundary wire and
power supply have been properly connected to the transmitter, the
green indicator light(s) on the front of the GroundsKeeper will go on.
The two additional lights will go on as you increase the range.
Power. Plug the power supply into the transmitter jack labeled PWR”.
Note: On the back of the transmitter Is a small switch. This switch
sets your transmitter to the correct broadcast frequency. Your dealer
will set this switch for your system. Do NOT change this setting. It is
for DEALER USE ONLY

Step-by-step Instructions
•Install the GroundsKeeper and boundary wire and make sure the
receiver collar is adjusted properly.
(See the receiver Operating Instructions for 'Setting The Receiver')
•Place boundary flags on the edge of the boundary area - the
zones in which the receiver collar picks up a radio signal. Boundary
flags serve as visual clues for your pet (see Figures 4 and 5).
•Attach a leash to your pet’s regular collar and play with him in
the safe zone for a few minutes. Holding the leash, walk to the
boundary area, shake a boundary flag in front of him, and firmly
say, “Watch out!” or “Careful!”
•Repeat the step above several times then allow him to walk just
past the boundary flags. As he passes the flags, he will receive
an audible warning and an electrical stimulation. Immediately call
out, “Watch out”, and use the leash to pull your pet back from the
avoidance zone. Return him to the safe zone and play with him
for a few minutes to reinforce the idea that there is a safe zone
where he can play.
•Again, allow your pet to approach a boundary flags. If he hears
the audible warning and retreats to the safe zone, reinforce the
behavior with praise and aection. If your pet fails to stop at the
audible warning and receives an electrical stimulation, say
“Watch out” and use the leash to pull him back to the safe zone
before he crosses completely into an avoidance zone.
•Your pet will quickly learn not to go near the boundary areas. Each
time you set up a new boundary area, be sure to retrain your pet.
Figure 4 Figure 5

Training
Understanding “avoidance training” and following the rules during
training will ensure that you and your pet get the most from your
system.
•Your pet does not intuitively know that he or she is not welcome
in all areas of your yard.
•Be aware that pets are sensitive to your attitude and mood. Stay
“upbeat” during a training session and he will be more receptive
to the training.
•Reward and reinforce good pet behavior.
•The system relies on “avoidance training” techniques. Your
yard is divided into safety and avoidance zones (see Figure 3).
If your pet advances toward an avoidance zone, he will receive an
audible warning. If your dog continues to move toward the
boundary wire after hearing the warning beeps, he will receive a
correction. Through training, your pet will learn to stay away from
areas that he associates with the audible warning.
•Do not comfort your pet after he receives a correction, as you will
be reinforcing anxiety.
•Even though you consider your pet a friend, eective training
depends on you being the leader and your pet being the follower.
•Be consistent! Do not break the training rules, even on special
occasions when you are tempted to allow your pet into a boundary
area “just this once”. Make sure all family members follow the rules.
Figure 3
Boundary Wire Avoidance
Zone
Safe Zone

Batteries
For replacement batteries and collars, contact your authorized
DogWatch Dealer, visit our website at www.dogwatch.com or call
Customer Service at 800-793-3436, Eastern Standard Time.
IMPORTANT: The use of batteries other than those authorized
by DogWatch Inc. can cause erratic operation of the receiver
or could cause permanent damage. The use of unauthorized
batteries will void the warranty on the receiver.
Warranty
DogWatch Inc., subject to the terms and conditions set forth
hereunder, hereby warrants that it will repair or replace, at its
own discretion, without charge for parts or labor, the Product or
any part thereof which is found by DogWatch Inc. to be defective
by reason of improper workmanship and/or materials for a
period of two (2) years from the original date of sale hereunder.
Warranty claims may be subject to Dealer service charges and/or
manufacturer shipping and handling charges.
As a condition to this warranty, Customer must (a) mail the
warranty card provided with the product to DogWatch Inc., 10
Michigan Drive, Natick, MA 01760, [phone], within seven
(7) days after purchase hereunder, (b) notify DogWatch Inc. within
two (2) years after the purchase hereunder of a claimed defect,
and (c) mail product back, insurance and postage prepaid to the
authorized DogWatch Dealer or DogWatch Inc.
EXCEPT FOR THE EXPRESS WARRANTY STATED ABOVE, DOGWATCH
INC. DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
DOGWATCH INC.’S SOLE LIABILITY UNDER THIS WARRANTY SHALL
BE TO REPAIR OR REPLACE, AT ITS OPTION, ANY PRODUCT OR PART
WHICH DOGWATCH INC. DETERMINES TO BE DEFECTIVE. IN NO
EVENT WILL DOGWATCH INC. BE LIABLE FOR ANY SPECIAL, INDIRECT
OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE PURCHASE
OR USE OF THE PRODUCT. IN NO EVENT SHALL DOGWATCH INC.’S
LIABILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT.

Troubleshooting
RECEIVER
•Check to see if the transmitter is “on”.
•Take the receiver o the dog and check the receiver by placing
the test light on the contact posts and holding the receiver next
to the transmitter or boundary wire.
•Ensure that the contact points on the receiver collar actually
touch your pet’s skin; tighten the collar as required.
•Replace the battery if necessary.
•Be sure the battery is inserted correctly.
TRANSMITTER
•Check to see If the power is “on” and that there is a green light.
•Make sure that the power supply transformer is securely
plugged into the wall outlet and that both the power supply
plug and the boundary wire are connected to the transmitter.
•Adjust the Range “+/ - “. You may have too narrow a range,
allowing your pet too close to the boundary area before
receiving a warning.
•Never adjust the transmitter while your pet is wearing the
receiver collar.
BOUNDARY WIRE
•Check to see if the transmitter is “on.
•If you have a broken boundary wire the green loop light will go
out and an audible warning will sound.

This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
DogWatch products are lead-free and compliant with the
Reduction of Hazardous Substances (RoHS) initiative.
©2018 DogWatch Inc. All rights reserved. 295052 Rev. C 12-18
10 Michigan Drive •Natick, MA 01760 •800-793-3436
www.dogwatch.com