DOM Unitecnic 1250 User manual

Unitecnic 1250
Instruction manual

2
UNITECNIC 1250 - INSTRUCTION MANUAL
Kit Content
The content
Accessories
■ External case
(With keypad)
■ External flange
■ 2 columns + 2 rings
■ 1 red tumbler
■ 1 blue tumbler
■ Code tumbler
(Red and Blue)
■ Elongate square
for thick door
Warranty: 24 months
■ Do not paint the cases.
■ Before using the door,
test all the functions of
the code lock, open door.
■ The warranty expires
in case of breach of
the mentioned rules,
improper modification
of the code lock, in case
of mechanical damage
to the code lock by the
customer, or if the lock
was obviously opened
and thus the seal broke.
■ 1 Spindle square 7mm
■ Internal case
■ Internal flange
■ set of cover EA70
■ 2 sets of 4 fixing screws
■ Panic device
adaptation kit
■ Set of cover for cylinders
■ Tweezer for
code tumblers
■ Operating manual
■ Drilling template

3
UNITECNIC 1250 - INSTRUCTION MANUAL
Characteristics
Technical features
Applications Indoor or outdoor installation
Theoretical Locking Combinations 500000
Combinations From 4 to 6 patterns
Lock Handing Reversible
Material Zamak
Handle fonctions Free access mode from the keypad
Always Free Exit Yes
Standard Finish Painted Silver
Minimum Door Thickness (mm) 35
Maximum Door Thickness (mm) 48
Assembly Information Can be combined with panic bars and Fercomatic
locks thanks to adaptation kits
Accessories Included Set of covers for European cylinders, interaxis
70mm, 2 Replacement code tumblers, Code
tumblers manipulation pliers, Adjustable Spindle
Square 7 mm, Installation Instruction, Code change
instructions, Drilling Template

4
UNITECNIC 1250 - INSTRUCTION MANUAL
Code change and free access
Internal side of the external case
1. Remove carefully the plate.
(Be careful not to lose any springs)
2. Code change.
■ Carry out this operation by
continiously pressing the “C” button.
3. Extract the concerned tumbers,
then insert them to the chosen
locations. (Using the tweezer
supplied as an accessory)
■ The opening code is determined by
the red tumblers.
■ Insert the blue tumblers on the
remaining locations.
.
Red tumbler
(code)
White tumbler
(Free access)
Blue tumbler
(neutral)
Unscrew the
4 red screws
2The reset “C” tumbler
doesn’t move.
1To be removed if
this option is not
required. (Leave the
slot empty) Do not
move the tumbler.
Do not put another
tumbler in this slot.
2
1
Be careful with the direction of the
tumblers. A tumbler inserted upside
down can damage the mechanism.
Keys prevent a wrong assembly.

5
UNITECNIC 1250 - INSTRUCTION MANUAL
Only the red screws can be unscrewed.
Any other internal disassembly is
prohibited. (cancellation of warranty)
!Attention
4. Number of terms change.
(Be careful not to lose any springs)
■ It is possible to reduce the number of
terms in a combination by replacing
one of the red tumblers with a blue
tumblers provided.
■ It is possible to increase the number
of terms in a combination by
replacing one of the blue tumblers
by a red tumblers provided.
5. Close the mecanism
■ Push to the max, the tumblers into
their housing, then replace the plate.
6. Carry out several tests
■ Enter the new code.
Always proceded by “C”.
So it is possible to turn the handle.
In case of non-operation.
Check that only the red tumblers
are pushed when entering the code
on the keypad: They are visible
through the holes in the spring plate.
(The order of the terms of the code
doesn’t matter).
Replace the
4 red screws

6
UNITECNIC 1250 - INSTRUCTION MANUAL
Handling change
By default, the code lock is configured in the
right hand
External case
■ Remove the internal screw of the han-
dle, releasing the handle cover.
■ Remove the 2 screws that connect the
handle to the lock.
(Seen from outside, the code lock is on the le on the door)
■ Li the handle o and reverse it to le
hand.
■ Replace all screws securely.
■ Repeat the same for the internal case

7
UNITECNIC 1250 - INSTRUCTION MANUAL
Spindle adaptation
Adapt the length of the special spindle ac-
cording to the thickness of the door,
by breaking o one or both ends.
From 50 mm to 55 mm (Leave as is)
From 43 mm to 50 mm (Break one side)
From 35 mm to 43 mm (Break both sides)
It is imperative to use 2 pliers to break
the flat spindle; Position them as close
as possible to the break mark.
!Attention

8
UNITECNIC 1250 - INSTRUCTION MANUAL
Drilling scheme
Advice
■ Mark the holes on both
sides of the door, to avoid
symmetry problems
during assembly.
■ Drill on one side at the
half door thickness.
Then drill entirely
through the other side
by making the holes
meet.
This method also prevents
splintering of the wood.
In the case of a door already
equipped, remove the
handles, rosettes, etc.
Check that the lock’s backset
is at least 45mm. If not,
replace it, favoring a 50mm
backset.
If the door is not already fitted
with one, install a mortice
lock, backset at 50 mm min.
Using tape, place the drilling
template on the door. The
spindle serves as a reference.
Mark the 4 holes and drill.
(12mm drill bit)
Door edge
Leave in place the spindle

9
UNITECNIC 1250 - INSTRUCTION MANUAL
Code lock mounting
Installation of the spindle in the follower
Assemble the front side
■ Dierent layout depending
on the door’s handling
If necessary:
change the combination and/
or modify the free passage
option beforehand.
(See page 4 and 5)
16mm screw
flat head
Threaded hole
Male / female spacer
Keypad side view
smooth hole
Cylinder’s cover
Ring

10
UNITECNIC 1250 - INSTRUCTION MANUAL
Code lock mounting
■ 50 mm for door
from 30 to 40mm
■ 60 mm for door
from 40 to 50mm
■ 30 mm for door
from 35 to 43mm
■ 40 mm for door
from 44 to 55mm
Screws:
Flat head screw:
2
3
4
5
6
7
6
Interior side Outside side
Screw 20mm
Cylinder cover
Unscrew slightly the cylinder screw
For the flap version only
■ Push the button.
■ Slide the flap upwards until it clicks.
■ To hide the keyboard again, slide the
flap down until it clicks.