domi LGFP1581 User manual

Use bolts to secure the frame to the ground to against the strong wind.
！

Pole Beam
Corner Roof BarBeam
Roof Bar
Corner Roof Solidifying Bar
Corner Roof Bar Connector
Corner Roof Solidifying Bar
Corner Roof Solidifying Bar Corner Roof Solidifying Bar
Finishing Bar Finishing Bar
Finishing Bar Finishing Bar
Finishing Bar Solidfying Bar
1

Solidfying Bar Roof Panel
Roof PanelRoof Panel
Roof Panel Roof Panel
Roof PanelRoof Panel
Plastic Bar Base Joint Cover
Joint Cover Union Bar Corner
Solidifying Bar
Corner
Solidifying Bar
Inside Roof
Connector Outside Roof Connector J-Hook Bracket
Bracket Hook
BracketBracket
2

Joint Cover
Bracket Bracket Joint Cover
Corner Cover Spacer Finishing
End
Solid Sidewall Mosquito
Sidewall Mesh
Finishing
End
3

4
(1) Attach 2 Part #B1 to
Part #A with 4 Bolts #8.
(2) Attach 2 Part #B2 to
Part #A with 4 Bolts #6.
(3) Attach Part #B to
Part #A with 3 Bolts #8.
(4) Repeat the above procedures to assemble the other three Part #A.

(5) Repeat the above procedures to assemble
the other three sides.
32
5
(1) Insert Part #X into Part #C1.
(3) Insert the other side of
Part #C2 into Part #C1
and secure with 4 Bolts #8.
(2) Insert one side of
Part #C2 into Part #C
and secure with 4 Bolts #8.
(4) Secure Part #X with 2 Bolts #3.
X4

(1) Connect Part #C and #C1 to Part #A
with 4 Bolts #4 and 4 Bolts #5 (From Outside).
6
Please don’t tighten all the bolts.
(2) Repeat the above procedures to assemble
the other three sides.

CC1 CC1
(1) Connect Part #C and #C1 to Part #A
with 4 Bolts #8. (From Inside)
7Please don’t tighten all the bolts.
(2) Repeat the above procedures to assemble
the other three sides.

C1
C1
8Please don’t tighten all the bolts.
(2) Repeat the above procedures to assemble
the other three sides.
(1) Affix Part #R and #R1 to the frame with 8 Bolts #8.

9Tighten all the bolts.
(3) Repeat the above procedures to assemble the other three sides.
(1) Cover the corner with Part #X1
and secure with 2 Bolts #2.
(2) Put Part #X2 on the protruding
place and secure with 2 Bolts #3.

Assemble the 4 Corner Roof Bars:
10
8

(1) Please have a freestanding ladder ready
at the center of the gazebo.
(2) Place 4 Part #E1 on Part #S; secure with
8 Bolts #8 (from bottom to top).
ATTENTION: You can also finish this step
on the ground and then lift 4 Corner Roof Bar
and Inside Roof Connector to the top together.
(Need 2 people and 2 ladders)
(3) Place 4 Part #E on 4 Part #A; secure with 8 Bolts #8.
11
U

C
C1
(1) Place Part #E2 on Part #S;
secure with 2 Bolts #8( from bottom to top).
(2) Connect Part #E2 and the Assembled Beam (C&C1)
with Part #U1. Secure with 3 Bolts #8.
(3) Repeat the above procedures to assemble the other three side.
12

(1)Attach Part #U2 to Part #F/F1/F2/F3 with Bolt #6.
(2)Repeat the above procedures to assemble the other 3 pieces.
13

(1) Insert Part #F2 and Part #F3 into Corner Roof Bar Part #E;
secure with 2 Bolts #6.
(2) Insert Part #F and Part #F1 into Corner Roof Bar Part #E;
secure with 2 Bolts #6.
(3) Connect Part #F/F1/F2/F3 and the Assembled Beam
with Part #U2; secure with Bolt #8.
(4) Repeat the above procedures to assemble the other three sides.
F1/F3 F/F2
F/F2 F1/F3
14
W1

(2) Attach Part #K and Part #K1
with Part #W3 and 2 Bolts #8.
(3) Connect Part #K (K1) and
Part #F2 (F3) with Bolt #9.
(4) Repeat the above procedures to assemble the other three sides.
K/K1
F2/F3
15
12
(1)Insert Part #W3 to Part #K1 and secure with Bolt #8.
w
1
F2 E2 F3 F2 E2 F3
X4
2x

(1) Insert Part #W2 into
Part #K1 and Part #K.
(2) Secure them to Part #E
with 3 Bolts #8.
(3) Repeat the above procedures to assemble the other three sides.
16

Secure Part #T to Part #Z2, Part #S and Part #S1.
ATTENTION: The holes of Part #Z2, Part #S and Part #S1
need to be aligned, on the same vertical line.
17
(From bottom to top)
Mesh

Insert Part #Q1 into the hole that
around the edge of Part #Z2.
18
Mesh