Dorma CS 80 MAGNEO Manual

CS 80 MAGNEO
Automatic sliding door operator
—
Installation and maintenance manual

2DORMA
Contents 02.2012 Page
1. Technical Data and Features 3
2. Greetings/Required Tools 4
3. Important Installation Instructions 5
4. Safety Instructions 6
5. Functional Characteristics 9
6. System Overview 11
7. Before Mounting 12
8. Installation Instructions for On-Wall Mounting 15
9. Installation Instructions for In-Wall Mounting 23
10. Connection Diagrams 29
11. Cable Channel 30
12. Connection of Closing Edge Protection 31
13. Commissioning 32
14. Operation Instructions 34
15. Daily Safety Checks 36
16. Troubleshooting Instructions 37
„Original documentation“
Read this manual carefully before starting the installation.
REMARK A remark will call your attention to important information that will facilitate
your work with the CS 80 MAGNEO.
ADVISE An advice will warn you that you could damage the CS 80 MAGNEO and
explain how to avoid this.
ATTENTION Here we will inform you of dangers that might cause damage to property
or injure or kill people.
Installation and Maintenance Manual
CS 80 MAGNEO
—

3DORMA
1.Technical data and features
Power supply: 115VAC ±10%; 50/60 Hz
Branch circuit protection (by others): 15 A
Cable type: 14 AWG (12 Max) [max. 3 x 1.5 mm2]
Power consumption without external accessories:
Stand-By-Mode: 5.6W
Automatic-Mode: max.60W
General information:
Temperaturerange: 0 - 104° F [0 - 40° C]
Operating noise of operator: max.55 dB (A)
Door panel height: max. 118” [max. 3000 mm]
Door panel weight: 44 lbs - 175 lbs [20 kg - 80 kg]
Weight of operator: max.passage width Operator length
without cover
Weight of operator
34.4” [875 mm] 68.9” [1750 mm] 18.9 lbs [8.6 kg]
39.4” [1000 mm] 78.7” [2000 mm] 20.7 lbs [9.4 kg]
44.3” [1125 mm] 88.6” [2250 mm] 22.4 lbs [10.2 kg]
FCC 15.105 (a)
NOTE:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Installation and Maintenance Manual
CS 80 MAGNEO
—

4DORMA
Dear customer,
We are pleased that a DORMA automatic sliding door has been chosen for this installation.
DORMA carefully designed, tested and built the door of high quality materials as it will provide
many years of service.
Now the door must be installed and adjusted properly to ensure its proper operation and safe
use.
To install and adjust the door for proper and safe operation, the installer must carefully read
this instruction book before proceeding, then follow the instructions exactly.
The door is designed to be installed only by trained and knowledgeable installers.
The installation technician should be experienced in the installation of the automatic entrance
product line.
After installation, the door must be adjusted to confirm with DORMA recommendations and all
code requirements. Be sure to carefully study the requirements in these instructions.
After installation and adjustment, the installer’s final responsibility is to properly instruct the
owner in the safe use of the door. He must also present the owner with the CS 80 MAGNEO
Owner’s Manual and carefully explain how to perform the daily safety check test.
Each step of the installation, adjustment and instructions are important for proper and safe use
of the door being installed. If there are any questions about any items contained in these
instructions, call the DORMA Technical Support Group for assistance.
Yours faithfully,
The DORMA-Team
Required tools:
• Tapemeasure
• Spiritlevel
• Pencil
• ElectricDrill
• MasonrydrillbitØ1/4”
• MetaldrillbitØ1/8”+Ø5/16”
• Socketwrench(10mm)
• Smallflatheadscrewdrivertoconnecttheterminalsonthecontrolunit.
• Phillipsscrewdriverforcountersunkscrewsofwallconnection.
• Allen(Hex)key,4mm
• Combinationwrench,wrenchsize10mmand13mm
• Long-nosedpliersforconnectiontoterminals.
• Adequatescrewsandwallachorsforthestructures,
in case they are not made of brickwork or concrete.
Additionally for DORMA MANET fixing:
• Allen(Hex)key,3mmand5mm
Installation and Maintenance Manual
CS 80 MAGNEO
—

5DORMA
Important Installation Instructions
ALL INSTALLATIONS AND SERVICE SHOULD ONLY BE PERFORMED BY TRAINED OR AU-
THORIZED PERSONS
Warning - To reduce the risk of injury or death:
1. Carefully Read And Follow All Installation Instructions.
2. This unit should only be installed in a rough opening capable of providing proper structural
support.
3. Always disconnect the power supply before servicing.
4. To install and adjust the door for proper and safe operation, the installer must carefully
read this instruction book before proceeding, then follow the instructions exactly.
5. The door is designed to be installed only by trained and knowledgeable installers.
The installation technician should be experienced in the installation of automatic
entrances. They should know all local code requirements and be familiar with the
requirements of the current ANSI A156.10 & 156.19 Standards for Power Operated
Pedestrian Doors.
6. After installation, the door must be adjusted to conform with DORMA recommendations
and all code requirements. Carefully study the requirements in these instructions.
7. After installation and adjustment, the installers final responsibility is to properly
instruct the owner in the safe use of the door. He must also present the owner with this
manual.
8. Each step of the installation, adjustment and instructions are important for proper and safe
use of the door being installed. If there are any questions about any items contained in
these instructions, call the DORMA Technical Assistance Group for assistance.
9. Save these instructions for future reference.
Compliance with Safety Standards
Your door system was designed to the latest operating and safety standards. In order to ensure
the continued safe operation of your door, it is important that:
• Yourdoorsystembemaintainedincompliancewiththestandardsofthe
industry, BHMA/ANSI.
• Properdecalsandlabelsbeapplied,perBHMA/ANSIStandards,andmaintainedonyour
doors. If decals are removed, or cannot be read, request labels to be replaced when calling
for service.
Installation and Maintenance Manual
CS 80 MAGNEO
—

6DORMA
4. Safety Instructions
4.1 Specified standard operation
The CS 80 MAGNEO is only designed to open and close doors.
Do not allow children to play with the CS 80 MAGNEO or rigidly mounted adjustment
and/or control devices. Keep remote controls out of reach of children.
4.2 Product-specific characteristics
The CS 80 MAGNEO is intended for use on interior single-panel sliding doors.
The CS 80 MAGNEO is neither suitable for application in escape routes, nor on fire and
smoke doors nor on exterior doors.
4.3 Standards, laws, codes and regulations
CS 80 MAGNEO is a low energy product and complies with the kinetic force limitations of
theANSI156.19LowEnergyStandards.
The standard only covers swing doors at this point.
Danger spots at closing edges
Automatic doors might cause hazards
by crushing, shearing, hitting and
closing edges.
Systems with CS 80 MAGNEO offer the following benefits:
• Thesystemdoesnothavetobeequippedwithadditionalprotectionequipment
(not compulsory).
• Theapplicationofsafetysensorsattheclosingedgesasadditionalprotectionmeasure
is optional and lies in the discretion of the person performing the installation of the door
system under consideration of the result of the individual risk assessment.
Risk assessment on the part of the installer:
Special spatial conditions and certain user groups might make it sensible to equip the
applicationwithsafetysensorevenwhenthesystemisoperatedinLow-Energy-Mode.Whether
this is required or not has to be assessed with the aid of an individual risk assessment and must
be considered during the planning of the system and by the manufacturer, i.e. the party
performing the installation of the system. We would therefore ask you to have a look at our risk
assessment form, which is available on our homepage www.dorma-magneo.com and will help
you to perfom the risk assessment.
Special requirements regarding the protection of people in need of protection. In case the risk
assessment reveals that there is a health risk of injury when the door hits a user in an unaccep-
table way, additional protection via safety equipment (connection of safety sensors) is required.
This is especially necessary when people in need of protection (children, elderly people or
disabled people) use the door.
Main
closing edge
Secondary
closing edge
Installation and Maintenance Manual
CS 80 MAGNEO
—

7DORMA
4.4 Limitation of liability
The CS 80 MAGNEO must only be used according to its specified standard operation.
DORMA will not accept any liability for damages resulting from unauthorized modifications,
unsafe, or improper installation or use of the CS 80 MAGNEO.
4.5 Documentation
Using control elements, making adjustments or performing procedures that are not
described herein might cause electric shocks, danger caused by electric voltage/current
and/or dangers due to mechanical incidents.
This documentation contains important information for the safe installation of the system.
Read these instructions thoroughly before you mount, install and use the CS 80 MAGNEO.
It is important for your personal safety to abide by the instructions mentioned in this
documentation. An incorrectly performed installation of the system might cause serious
injuries.
Please keep this documentation for later reference.
4.6 General information regarding the installation of the system
The CS 80 MAGNEO must be disconnected from power supply (de-energized) when per-
forming mounting or installation work. Remove the power plug, or, in case of permanent
power supply, switch off fuse.
• Securetheworkingareaagainstunauthorizedaccessofotherpeople.
Falling items or tools might cause injuries.
• Inanycase,thewayofmountingandthemountingequipment,likeforexamplescrews
and wall plugs, have to be adequate with regard to the structural conditions (concrete,
wood, plasterboard etc.)
• Assoonasyouhaveloosenthescrewsoftheendstop,boththeendstopandthecarrier
could fall out of the operator. Therefore you should always hold the operator straight.
• PayattentionthatnowaterorotherliquidsdroponorintotheCS80MAGNEO.
• NeverstickmetalobjectsinsidetheopeningsoftheCS80MAGNEO.Otherwiseyoucould
sustain an electric shock.
• NeverputyourhandinsidetheCS80MAGNEOinordertoavoidinjuries.
• Laythepowercordsothatnobodycantripoverthecableorunplugitbymistake.
• DonotoperatetheCS80MAGNEOwhenthepowercordisdamaged.
• Alwayspullattheplugandneveratthecablewhenunpluggingthepowersupply.
• Onlyoperatethemainsswitchattheheaderprofilewhilethedoorstandsstilloris
permanently open.
• Nopushbuttons/switches,picturesetc.mustbelocatedwithinthedoor‘smovementrange.
Baseboards have to be removed if required.
• Ifaswitchisusedforactivationofthedooritmustbelocatedsothatthedooroperation
can be observed by the person operating the switch.
• Followingthesuccessfulinstallationofthesystem,youhavetocheckthesettingsaswell
as the CS 80 MAGNEO and the safety devices for proper functioning.
• Theinstallationdescribedhereinisonlyanexample.Structuralorlocalconditions,avaible
tools or other conditions might suggest a different approach.
• Permanentwiringistobeemployedasrequiredbylocalcodes.
Installation and Maintenance Manual
CS 80 MAGNEO
—

8DORMA
4.7 Residual risks
Automatic doors might cause hazards by crushing, shearing, hitting and drawing-in.
Depending on the structural conditions, the door version and the safety equipment, residual
risks can not be excluded.
4.8 Waste Electrical and Electronic Equipment (WEEE) Directive
Within the European Union, this device must not be disposed of as
domestic waste. It has to be disposed of at as pecial facility so that it can
be recycled.
CS 80 MAGNEO - Awarded safety
Developed according to the latest safety standards:
+ Low-Energy-ModeinaccordancewithDINstandard
+ Tested Safety
+ -mark
+  -mark(UL325/CSA22.2)
+ -mark (Part 15.105(a))
Installation and Maintenance Manual
CS 80 MAGNEO
—

9DORMA
5. Functional Characteristics
5.1 General information
The CS 80 MAGNEO is a single-panel
Low-Energy-Modeslidingdooroperatorfor
small and light interior doors with an
admissible weight from 44 lbs to 175 lbs per
door panel. The opening and closing speed
respectively depend on the weight of the door
panel and can be adjusted via a
potentiometer (infinitely variable).
5.2 Commissioning
During the first commisioning of the operator,
the installer has to perform a learning cycle
according to the commissioning instructions.
When the installer connects the system to the
power supply (plugs it in) the light indicator
at the operator will blink and the operator
has no function. The door can be opened and
closed manually. Following the learning cycle
the light indicator goes on and the operator is
ready for operation.
5.3 Energy Modes (Maximum Force Limited)
With the aid of a sealed switch (located inside
the operator), the system can be switched
fromLow-Energy-ModetoFull-Energy-Mode.
Low-Energy-Mode
The standard ANSI 156.19 states the energy
with which a swing door panel hits an obstac-
le must be limited. The CS 80 MAGNEO
operator moves the sliding panel at a low
speed corresponding to ANSI 156.19 energy.
The potentiometer (located inside the opera-
tor) can only be used to reduce this calcula-
ted speed.
Full-Energy-Mode
The forces are limited in this mode as well.
The speed is infinitely variable with the aid of
a potentiometer (located inside the operator).
Even though the door may open at a fast
speed. The closing cycle always remains in
Low-Energy-Mode
5.4 Operation modes
OFF: The operator is switched off.
You can move the door by
hand.
AUTOMATIC: When the system has been
activated via pushbutton,
radio remote control or
similar, the operator opens
the door and closes after
expiration of the adjusted
hold-open time.
PERMANENT The operator opens the door
OPEN: and holds it in “open“ posi-
tion until it receives an other
signal.
When the system is delivered, the
CS 80 MAGNEO is adjusted to AUTOMATIC
Mode.
An external program switch is required to
change the operation mode.
5.5 Functions in AUTOMATIC Mode
Push & Go
As soon as the door is moved manually into
opening direction by approximately 3/8”
[10 mm], the operator will automatically
move the door panel further in the desired
direction. The door closes automatically.
Permanent Open via double-click
A double-click on the push button (activate
the pushbutton twice in quick succession)
will open the door. When you double-click on
the button for a second time or move the door
panel by hand, the door will close.
Opening/closing via pushbutton
As soon as you push the button or move the
door manually the door will open. When you
push the button for a second time or move
the door panel by hand, the door will close.
Installation and Maintenance Manual
CS 80 MAGNEO
—

10 DORMA
Express-Function
The door can be moved manually in its
driving direction and there will be no extra
resistance. However, when the maximum
speed is exceeded, the driving resistance will
increase in line with the speed by which it is
exceeded. As soon as the user has released
the door panel, the operator will softly slow it
down to maximum speed. This function is
activated during all opening and closing
cycles.
5.6 Safety functions
StaticforcesinLow-Energy-Mode.
The system does not exceed a value of 15 lb
during opening and closing cycles.
Opening cycle
As soon as the door hits an obstacle during
an opening cycle, it will immediately stop and
remain in its position for 3 seconds. Then
the operator will try to continue the opening
cycle. If the door panel hits an obstacle three
time during an opening cycle, it will close.
Closing cycle
When the door panel hits an obstacle while
closing, it will immediately stop and perform
an opening cycle.
5.7 Safety sensors
You can install sensors to detect obstacles.
An automatic sensor test can be activated
or deactivated via the DIP switches located
inside the operator.
The door will stop immediately when the
sensor detects an obstacle during an opening
cycle and will continue the cycle as soon as
the obstacle has been removed. In case the
obstacle is not removed, the door will close on
completion of the adjusted hold-open time.
The door will stop immediately and reverse
when the sensor detects an obstacle during
the closing cycle. This function is not activa-
ted while the door is in closed position (then
the sensor is deactivated).
5.8 Power failure
In the event of a power failure, the door can
be opened and closed by hand.
However, in this case the operator does
not slow down (brake) the door panel, so
that the user has to move (hold) it all the
way by hand.
As soon as the voltage returns, the operator
will automatically perform a position initiali-
zation.
During this position initialization, it is
essential that the movement range of the
door is free of obstacles.
Installation and Maintenance Manual
CS 80 MAGNEO
—

11DORMA
Driving direction open
Optional Power Cord
CS 80 MAGNEO
Control unit and connection
terminals for external accessories
8
7
6
5
4
3
2
1
ON
DIP switch LED
light indicator
Potentiometer
hold-open time
Connection terminals for
external accessories
Mains switch
Energy mode switch
(Full-Energy/Low-Energy)
(located below the seal)
Potentiometer
speed adjustment
Reset button
Start
learning cycle
To reduce the risk of electric shock, this
equipment has a grounding type plug that
has a third (GROUNDING) pin.This plug
will only fit into a grounding type outlet.
If the plug does not fit into the outlet,
contact a qualified electrician to intall the
proper outlet.
DO NOT CHANGE THE PLUG IN ANY
WAY.
6. System Overview
Control unit and connection terminals for external accessories
Installation and Maintenance Manual
CS 80 MAGNEO
—

12 DORMA
7. Before Mounting
Basic requirements:
Work on electrical equipment may only be perfomed by properly qualified personnel
(electricians)
• Thefloorhastobelevel
• Glassdoorpanelshavetobemadeofsafetyglass.
• Theconnectioncablesforexternalaccessories(programswitchetc.)mustbelocatedinthe
close range of the operator before starting the installation of the system. (See Page 12)
• WithIn-Wallmounting,thewallmustnotbeclosedbeforethesystemhasbeenmounted.
When the system is installed with permanent power supply (the cable comes directly out of
the wall), ensure that the power supply line is dead (de-energized) during installation.
The power supply line must have the apropriate fuse protection in compliance with
electrical codes. Use only copper conductors for permanent connection, or use DORMA’S
optional power cord (refer to “For optional power cord connection” below for more details).
Opening direction:
The connections of the operator are always located on the side where the door is when it is
in the closed position.
Therefore the operator is symmetrical and can be turned the way your equire it. This installation
instructions show the system with connection on the right side. For left hand, just reverse the
orientation of the operator.
Please note:
In case you require additional accessories, please contact your local dealer. If you have tech-
nical questions or require help during the installation of the system, please contact our hotline
under the following number:
Please call the following number in case
of technical problems or further questions: 1-877-367-6211
For optional power cord connection
Use only DORMA’S DX3310-010 18” [457 mm].
(Nema5-15compatible).ULlistedpowercord.
The flexible power cord should not be routed
through doorways, window openings, walls,
ceilings, floor, or the like. The cord should also
not be, attached or secured to the building
structure; the cord cannot be concealed behind
walls and the like. Make sure the power cord
does not become entrapped in any moving parts
of the operator, door, or system.
For in-wall mounting:
When installing the socket, please remember that
you should be able to reach it by hand. (Max 14” away)
max. 14"
CS 80 MAGNEO
Installation and Maintenance Manual
CS 80 MAGNEO
—

13DORMA
1.
2.
4.
1.
5.
2.
1.
2.
2.4"
(60 mm)
2.4"
(60 mm)
10" min
(min. 250 mm)
In order to facilitate the cabling inside the
operator, all cables should have a length of
at least 10”.
For on-wall mounting
If you want all connection cables that are
coming out of the wall not to be seen after the
installation (only possible with permanent power
supply), they have to come out of the wall within
an area of 2.4” x 2.4” on the side where the
connections of the operator are located.
Installation with permanent power supply: When
the system is installed with permanent power
supply, the internal power supply socket has to
be removed.
Proceed as follows:
Loosenthescrewsattheendstopandmovethe
end stop to the center of the system.
Do not remove or screw down the end stop.
Then loosen the screw in the cover of the power
supply housing and remove the cover (on the
side where the connections are located).
Keep the cover and the screw in a safe
place as you will require it later.
Installation and Maintenance Manual
CS 80 MAGNEO
—

14 DORMA
1.
1.
3.
2.
Carefully open the cover of the control unit
housing by levering it out with the tip of a flat
head screwdriver
Loosenthescrewsoftheconnectionterminals
and remove the internal Schuko-type
shockproof socket.
Then close the cover of the control unit housing.
Move the end stop to the end of the channel and
screw it down.
The end stop must overlap.
Installation and Maintenance Manual
CS 80 MAGNEO
—

15DORMA
Mounting procedure
If there is a door frame, you have
to shim the angle brackets with
the shim plate (optional).
1. Auxiliary lines for positioning pur-
poses. See bottom of this page.
2.a Installation without shim plate.
See Page 16 and 17.
2.b Installation with shim plate.
See Page 18.
3. Further installation.
See Page 19 - 22.
Positioning Guide
For the installation without
shim plate mark the center of
the passage on the wall.
For the installation with shim
plate mark the center of the
passage on the wall. Please
have a look at the table for the
required dimension M for your
operator.Lcorrespondstothe
operator length.
Now mark the reference line.
Always mark the reference
line on the side of the main
closing edge.
34.4“ [875] 39.4” [1000] 44.3” [1125]
L68.9“ [1750] 78.7“ [2000] 88.6“ [2250]
M17.2“ [437.5] 19.7“ [500] 22.1“ [562.5]
In case the door panel
shall not be positioned in
the center of the passage,
the bracket or shim plate
has to be shifted by the
desired dimension.
==
Reference
line
Main closing edge
M
**Dimensions marked (=) are equal.**
Glass door panels with
MANET single-point fixings
Door panel information
Secondary closing edge
Main closing edge
8. Installation instructions for on-wall mounting
41.33" or other dimension
1050 mm or other dimension
Edge grinded glass
=C=
CENTERED
2.5" [63 mm]
2.2" [55 mm]
Glass width
Drill hole for
recessed door grip
(optional)
at least 2.76"
at least 70 mm
Operator lengthC
68.9" [1750] 22.7" [575]
78.7" [2000] 27.6" [700]
88.6" [2250] 32.5" [825]
„Closed“ side
Ø 1.03" [Ø 26) hole
C‘Sink Ø 1.26" [Ø 32] X 90°
Glass height = H - 5" [12 mm]
90°
90°
Ø 1.97" [Ø 57) hole
C‘Sink Ø 2.05" [Ø 52] X 90°
max.
.31"
8 mm
Angle
floor guide rail compl.
.250"
6 mm
Finished floor
2.5"
62 mm
at least .2"
at least 5 mm
Installation type
On-wall-mounting
Installation and Maintenance Manual
CS 80 MAGNEO
—

16 DORMA
L
C
CENTERED
X
.250"
6 mm
==
Passage width (PW)
Projection
max. 2.5"
max. 65 mm
Projection
Reference
line
Side with
connections
“Closed” position
• The“closed“positionisalwayslocated
on the side where the connections are.
• DimensionL(Lengthofoperatorand
fixing bracket) is measured without end
caps.
Take dimension X from floor level; then po-
sition and mark the upper edge of the fixing
bracket onto the wall.
Dimension X has to be measured at the
highest point of the floor within the mo-
vement range of the door system.
The distance between the bottom edge
of the door panel and the floor should
amount to .250” [6 mm], however, it
must not exceed .3125” [8 mm].
**Dimensions marked (=) are equal.**
34.4“ [875] 39.4” [1000] 44.3” [1125]
PW 31.9“ [810] 36.8“ [935] 41.7“ [1060]
L68.9“ [1750] 78.7“ [2000] 88.6“ [2250]
C22.6“ [575] 27.6“ [700] 32.5“ [825]
When using Wooden door panel:
X=doorpanelheight+3”[78mm]
When using Glass clamping rail:
X=doorpanelheight+4-1/2”[114
mm]
When using DORMA MANET
single-point fixings:
X=doorpanelheight+2.9”[74mm]
Dimension X has to be measured
at the highest point of the floor
within the movement range of the
door system.
Installation and Maintenance Manual
CS 80 MAGNEO
—

17DORMA
Center line
Before drilling any holes, make sure
there are no cables and/or pipes in the way.
Position the fixing bracket onto the center line.
Ensure that the bottom vertex of the triangle is
located exactly on the center line.
Aling the fixing bracket so that it is level.
Fix the bracket with screws
(one screw respectively per one oblong hole on
each side).
Use adequate wall plugs and screws depen-
ding on the prevailing structure
when fixing the bracket.
The supplied screws and wall plugs are
suitable for concrete and brickwork.
Recheck the fixing bracket for exact
positioning.
Drill the further holes through the drill holes in
the fixing bracket and fix the bracket with at
least 12 screws.
In case of uneven walls you have to shim the
bracket so that it does not bend.
Use the enclosed distance plates in different
sizes for this purpose.
Installation and Maintenance Manual
CS 80 MAGNEO
—

18 DORMA
Reference line
Mounting with shim plate
Position the shim plate at the reference line.
Calculate the dimension from the floor to the
upper edge of the shim plate as follows:
Doorpanelheight+3.1”[78mm]
When using DORMA MANET single-point fixings:
Doorpanelheight+2.9”[74mm]
Align the shim plate so that it is level and mark
the drill holes.
Before drilling any holes, make sure
there are no cables and/or pipes in the way.
Drill the marked holes and fix the shim plate.
Use adequate wall plugs and screws with
respect to the prevailing structure.
The supplied screws and wall plugs are
suitable for concrete and brickwork.
The load-bearing capacity of the fixing bra-
cket must amount to at least 528 lbs.
In case the frame is thicker than .375” you
have to underlay the shim plate with the
enclosed distance plates so that it is flush
with the door frame.
Use 12 screws to fix the bracket to the shim
plate.
Installation and Maintenance Manual
CS 80 MAGNEO
—

19DORMA
L1
N35 mm
6 mm
6 mm
150 mm
L1
N
6x
4.
2.
3.
1.
1.
3.
2.
5.
4.
1. Adhere 3 pieces of felt equally onto the
bracket.
2. The openings of the door panel
suspension have to point to the front
3. Wenn using MANET fixings, the door
panel suspensions have to be
unscrewed.
4. Fix the operator below the bracket with
6 hexagon screws (lock screws) (8 Nm).
You will have to move the carrier in order to
reach all 6 holes.
Connection of 120 V permanent power supply.
Working on electrical equipment may only
be performed by properly qualified staff
(electricians). Before starting with the
installation, make sure that the power
supply lines are dead (disconnected).
Loosentheendstopandmoveittothecenterof
the system (see page 13, picture in the middle).
Cut the leads to length, dismantle them and
connectL1andNtotheconnectionterminalsof
the power supply.
When connecting to conduit, use the included
conduit cover, mounting plate and phillips
screws
Step:
1. Attach plate to operator with (2) screws.
2. Route the wires and connect to the
operator.
3. Fold the conduit cover as shown.
4. Hook conduit cover to the plate.
5. Secure conduit cover onto the plate with
remaining screw.
Leveroutthecoveratthecontrolunithousing
with the aid of a screwdriver.
Laythegroundinglinethroughthehousingof
the operator as shown in the picture and connect
it to the grounding terminal (PE).
The grounding (PE) has to be connected in
any case.
Connect all external accessories but the safety
sensors. Please refer to the instructions for the
cable channel on page 30.
Installation and Maintenance Manual
CS 80 MAGNEO
—

20 DORMA
.3125" max.
[max. 8 mm]
1.
2.
3.
Close the cover of the control unit housing.
Fix and screw down the cover of the power
supply housing.
Move the end stop to the end of the channel and
screw it down thoroughly (see page14, picture at
the bottom).
Insert the panel into the door panel suspension
as indicated in the picture, align it so that it is
parallel to the wall and screw it down.
When using MANET fixings, please consider the
instructions enclosed with the MANET fixings.
The distance between door panel and wall
must not exceed .3125”.
Installation and Maintenance Manual
CS 80 MAGNEO
—