Dorma TS93 PT User manual

TS93 PT/PTH
—
Surface applied door closer
Installation instructions:
Push side track mount with dead stop (PT)
Optional hold open (PTH)

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]
08279211 05/14 Reamstown, PA 17567 Fax: [phone] Subject to change without notice
TABLE OF CONTENTS
—
Technical specifications
Note
1. Drawing is not to scale.
2. Dimensions are in inches/[mm].
3. Left hand door is shown.
4. Caution: sex nuts are required for attachment of
components to unreinforced doors and to wood or
plastic faced composite type fire doors, unless an
alternative method is identified in the individual door
manufacturer's listings.
5. Template is for 4-1/2 x 4-1/2 butt hinges & 3/4" offset
pivots
6. Maximum door opening degree is 110°.
7. Minimum door with 26".
Templates
Closer overall
Technical specifications
Door templates 2
Size selection chart 2
Closer setup
Exploded parts list
Handing of the door 3
A. Installing the surface closer
Installing back plate & angle bracket
Installing the surface closer 4
B. Adjustments
Adjusting the closing speeds
Adjusting the spring force 6
Adjusting the optional hold open 7
C. Installing the closer cover
Installing the cover 7
Contents
NOTE: Refer to the included drawings for push side door closer, back plate mounting templating.
NOTE: Refer to the included drawings for push side track, angle bracket mounting (soffit mount) templating.
Size selection chart
8. Hold open range is from 55° to 105° with optional hold
open kit.
9. Use closer body style "G" for this installation.
10. Arrows on closer mounting plate point upward.
Door Width
Closer Interior/
Exterior
2'-6"
min.
3'-0"
max.
3'-6"
max.
4'-0"
max.
4'-6"
max.
5'-0"
max.
TS9315 Interior
Exterior
TS9356 Interior
Exterior
N/A N/A
N/A N/A
N/AN/AN/A
N/AN/A N/A

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]
08279211 05/14 Reamstown, PA 17567 Fax: [phone] Subject to change without notice
TS93 PT/PTH
—
3
Closer setup
Handing the door
Follow included template to properly prepare door and
frame for all accessories of the closer installation.
Know the swing of the door which is being installed prior
to installation.
Make sure door efficiently operates prior to installing
closer.
Hinge Hinge
Exterior side of door
Interior side of door
Left hand door (LH)
Left hand reverse
door (LHR)
Right hand reverse
door (RHR)
Right hand door (RH)
The surface closer is comprised of the following components.
1. Closer body: "G" body
2. Main arm
3. Track assembly
4. Pinion
5. Cover and end caps
6. Track cover
7. Closing/sweep speed adjustment
8. Latch speed adjustment
9. Backcheck adjustment
10. Delayed action adjustment
11. Angle bracket
Verify closer spring size prior to installation. See "Size
selection chart" on page 2.
1
4
5
3
9
10
1
5
5
26
78
G
11

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]
08279211 05/14 Reamstown, PA 17567 Fax: [phone] Subject to change without notice
TS93 PT/PTH
—
4
Reference template 08279212
NOTE: For use on regular mount applications on the push side
of the door.
1
Installing the back plate and angle bracket
A. Installing the surface closer
Tools recommended
Drill Bits
Metal: No. 21 & 10-32 Tap
Wood: 9/64"
2
Installing the surface closer
NOTE: Orient pinion (1) closest to hinge.
NOTE: Make sure arrows on
plate point upward.
3
3.1 Using an adjustable wrench (and looking up at the
bottom of the closer):
Left hand door - turn the bottom pinion counter-
clockwise 5°.
Right hand door - turn the bottom pinion clockwise 5°.
3.2 Attach the main arm (1) to the top pinion with an
M6x20 socket head cap screw (2) using an M5 hex key.
Be sure the main arm is parallel to the door during
application.
1
2
#0 Phillips screwdriver
#2 Phillips screwdriver
3/16" flat head screwdriver
M2.5 & M5 Hex key
2.1 Attach the closer body (2) to the plate using the four
screws provided with the plate itself.
1.1 Attach the angle bracket (1) to the bottom of the soffit
using the three [10-32 machine screws or #10 wood
screws] provided.
1.2 Attach the back plate (2) to the mounting surface using
the four screws [10-32 machine screws or #10 wood
screws] provided with the surface closer.
2
1
2
1
Toward the
hinge
Left hand door

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]
08279211 05/14 Reamstown, PA 17567 Fax: [phone] Subject to change without notice
TS93 PT/PTH
—
5
4.1 Position the individual components inside the track
channel and screw down each fitting.
NOTE: For PTH ONLY - orient the hold open mechanism as
seen in the image above. Hold open mechanism and
hold open slide shoe must be installed with the arrows
pointing away from the hinges.
4.2 Attach the track channel (1) to the angle bracket (2)
through the end blocks with two flat head Phillips
screws (3).
5.1 Align the arm (1) with the slide shoe of the track channel. 5.2 Attach with one M8x15mm shoulder bolt (2) using an M5
hex key.
5
A. End block
B. Dead stop adjustable anchor
C. Cushion
D. Cushion protector
E. Hold open mechanism
F. Track channel
G. Slide shoe
H. Hold open slide shoe
2
2
1
3
1
Hinge
4
Part No.: TH KIT 93 ONLY
Closer is omitted in image for better
viewing of the track assembly.
Left hand door
Left hand door
Left hand door - No hold open
Left hand door - With hold open
Right hand door - No hold open
Right hand door - With hold open
DE
A BC
F
A
A
A
B
C
D
E
F
G
H
G
H
HINGE
HINGE
1

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]
08279211 05/14 Reamstown, PA 17567 Fax: [phone] Subject to change without notice
TS93 PT/PTH
—
6
1
B. Adjustments
Adjusting the closing speeds: sweep, latch or backcheck and delayed actions
Confirm closer spring size prior to making any closing
speed adjustments.
Do not back valves out beyond closer casting.
Door should close in 3 to 6 seconds from 90º.
Maximum opening angle is 110º.
1.1 Adjust the sweep speed (1) for the area from 70° - 0°
Increase sweep speed: Turn valve counter-clockwise
Decrease sweep speed: Turn valve clockwise.
1.2 Adjust the latch speed (2) for the area from 7° - 0°.
Increase latch speed: Turn valve counter-clockwise
1.3 Adjust the backcheck (3) for the area from 65° - 110°.
Increase resistance: Turn valve clockwise
Decrease resistance: Turn valve counter-clockwise.
1.4 Adjust the delayed action (4) for the area from
110° - 70°.
Increase delayed action: Turn valve clockwise
Decrease delayed action: Turn valve counter-clockwise
1 [Sweep] 2 [Latch]
3 [Backcheck]
Sweep
Latch
Backcheck
Delayed action
4 [Delayed action]
Adjusting the spring force
TS9315
NOTE: Supplied with a size 2 spring setting.
Barrier free openings: Take an opening force reading from the
pull on the door. If required, adjust the spring force to meet
the barrier-free requirement.
Decrease force: turn counter-clockwise 5 times (max)
Increase force: turn clockwise 12 times (max)
Depending on opening conditions, a door adjusted to meet
barrier-free forces may not have sufficient power to reliably
close and latch the door.
TS9356
NOTE: Supplied with a size 6 spring setting.
Increase force: turn clockwise 6 times (max)
TS9315
DOOR WIDTH FULL TURNS OF
SPRING ADJUSTER
CLOSER
SIZE
INT. EX T.
2'6" ----- 0 2
3' 2'6" +3 3
3'6" 3' +9 4
4' 3'6" +12 5
TS9356 4' 3'6" -4 5
4'6" 4' 0 6
CLOSER
TYPE
MAX DOOR
WEIGHT (LBS)
SPRING
SIZE
FULL TURNS OF
SPRING ADJUSTER
TS9315
100 2 0
125 3 +3
150 4 +9
200 5 +12
TS9356 200 5 -4
250 6 0
2
Increase
Decrease
Increase
Decrease
Increase
Decrease
Backcheck &
Delayed actions
Sweep & Latch
Speed
Do not close valves completely.

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]
08279211 05/14 Reamstown, PA 17567 Fax: [phone] Subject to change without notice
TS93 PT/PTH
—
7
1
1.1 Snap both end covers (1) into place.
1.2 Remove the un-needed tab (2), and snap the closer body
cover (3) into place.
C. Installing the closer covers
Installing the covers
1.3 Attach with a 4-40 Phillips pan head screw (4) .
1.4 Snap the track cover (5) into place.
Adjusting the optional hold open
3.1 Slide the hold open mechanism (1) to the desired
location inside the track, to hold the door open to the
desired degree.
NOTE: Refer to section A, step #4 for hold open mechanism
location dependent upon hand of door.
3.2 Using an M2.5 hex key, tighten the set screw (2) to
secure the hold open mechanism.
3.3 To adjust the force of the hold open force, engage the
hold open feature by opening the door and allowing the
hold open slide shoe (3) to slide over top of the hold open
mechanism and click into place.
3.4 Inside the M8x15mm hex screw (4) is a 2.5mm set
screw. To adjust the hold open force, use an M2.5 hex
key and turn the set screw:
Clockwise = increase force
Counter clockwise = decrease force
3
13
4
2
2.5mm set screw
(inside the M8x15 hex screw)
2
5
4
3
13
1

08279211 05/2014, Subject to change without notice
DORMA USA, INC.
DORMA DRIVE, DRAWER AC
REAMSTOWN, PA 17567
TOLL-FREE: 800-523-8483
FAX: [phone]
E-MAIL: [e-mail]
WWW.DORMA-USA.COM