Dormakaba ED100 User manual

ED100/ED250
Automatic swing door operators
Installation instructions
DL4614-010 – 11-2017
| EN |

2
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Table of Contents
Table of contents 
 General information 
 Product description 
 Safety information 
 ED/ED Product overview 
. ED/ED single swing door 
. ED/ED pair swing doors 
. Arm configurations 
. ED/ED operator component view 
 Accessory kits, axle extension kits 
. ED and ED configured for full energy
accessory kit 
. ED low energy accessory kit 
. Axle extension kits 
. Double door ED/ED operator
connection cables 
 Technical data 
. ED/ED Technical data 
. Operating specifications 
 Recommended tools and torque chart 
. Recommended tools 
. Standard tightening torque 
. Drill bits 
 Operational mode overview 
. ED/ED door closer modes 
. Low energy product 
 User interface 
. Overview 
.  button keypad and display 
. Program switch panel 
 System accessories 
 ED/ED door signage 
. Full energy operator 
. Low energy operator, ED 
. Door signage, full energy single swing door 
. Door signage, low energy single swing door 
. Door signage, full energy double swing
doors 
. Door signage, low energy double swing
doors 
. Safety label, automatic swing doors 
. Safety label, low energy swing doors 
 ED/ED arm configurations 
. Single swing door arm configurations 
. Double swing door arm configurations 
 Header installation 
. Installation preparation 
. Unpack header assembly 
. Remove operator from mounting plate 
. Single header installation 
. Install program switch panel in header 
. Double header installation 
Table of contents
. Pull arm installation template, butt hinge 
. Deep pull arm installation template, butt
hinge 
. Push arm installation template, butt hinge 
. Deep push arm installation template, butt
hinge 
. Center pivot door, surface applied header,
push arm template 
. Offset pivot door, surface applied header,
push arm template 
. Center hung door, SA header, CPD pull
arm as push template 
. Center hung door, surface applied header,
CPD pull arm template 
 ED/ED operator installation 
. Single header mounting plate installation 
. Double header mounting plate installation 
. Customer  Vac connection to
mounting plate terminal block 
. Double door header  Vac mounting
plate connection 
. Remove protective film strips from
operator 
. Install ED/ED operator on
mounting plate in header 
. Double header ED/ED operator
installation 
. Connect cables to ED/ED operator 
. Double header operator legend plate 
 Pull arm installation 
. Hardware 
. Track assembly 
. Install track and pull arm assembly 
 Push arm installation 
. Hardware 
. Assemble adjustment screw to connecting
rod. 
. Assemble drive arm to operator 
. Insert adjustment screw ball head into arm
socket 
. Fasten connecting rod shoe to door 
 Measure reveal depth, door width 
. Reveal depth parameter rd 
. Record reveal depth measurement,
rd value 
. rd parameter values 
. Door width parameter Tb 
. Record door width measurement, Tb value 
. Tb parameter values 
 Braking circuit plug 
. Braking circuit plug position 

3
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Table of Contents
 Operator spring tension 
. Set operator spring tension 
 Power fail closing speed 
. Set power fail closing speed 
 Parameters 
. Parameters 
 Single door first commissioning 
. First commissioning 
. Set configuration parameters 
. Perform learning cycle 
 Double door first commissioning 
. Separately commission active and inactive
doors 
. Set operator parameters for double door
operation 
. Connect communication cable between
operators 
 Set pull arm end stop 
. Set pull arm end stop position 
 Install pull arm track cover 
. Install track cover, spacer blocks and end
caps 
 Install push arm door stop 
. Install push arm bumper stop (optional
assembly) 
 Install header cover 
. Install header cover. 
 Install door signage 
. Install door signage 
 ANSI/BHMA standards 
. A. Power operated pedestrian doors 
. A. Low energy power operated doors 
 Upgrade cards 
. Upgrade cards 
. Container module 
. Installing upgrade cards 
Appendix A, Sensor wiring diagrams 
A. BEA LZR wiring diagram, single door 
A. BEA LZR wire harnesses, single door 
A. BEA LZR hub learning cycle 
A. BEA LZR wiring diagram, double door 
A. BEA LZR wire harnesses, double door 
A. BEA LZR hub learning cycle 
A. Optex Elite T swing door mounted sensor
- single door 
A. Optex OC-C T wire harness, single door 
A. Optex OC-C T setup 
A. Optex Elite T swing door mounted sensor
- double doors 
A. Optex OC-C T wire harness, single door 
A. Optex OC-C T setup 
A. BEA Bodyguard-T with approach side
Superscan sensor 
A.. BEA Bodyguard-T wiring and
commissioning, one sensor 
A. BEA Bodyguard-T with swing and
approach side Superscan sensors 
A.. BEA Bodyguard-T wiring and
commissioning, two sensors 
A. BEA Bodyguard-T with approach side
Superscan sensor,
double door active door 
A.. BEA Bodyguard-T wiring and commissioning,
one sensor active door 
A. BEA approach side Superscan sensor,
double door inactive door 
A.. BEA Superscan wiring and commissioning,
one sensor inactive door 
A.. BEA Bodyguard-T with approach and
swing side Superscan sensors,
double door active door 
A.. BEA Bodyguard-T wiring and commissioning,
two sensors active door 
A.. BEA Bodyguard-T with approach and
swing side Superscan sensors,
double door inactive door 
A.. BEA Superscan wiring and commissioning,
two sensors inactive door 
A. Optex Premier T header mount sensor 
A.. Optex Premier T wiring and commissioning 
A. Optex OA-Edge T door mounted mounted
approach side sensor 
A.. Optex OA-EDGE T wiring and
commissioning, approach side sensor 
A. Optex OA-Edge T door mounted mounted
approach and swing side sensors 
A.. Optex OA-EDGE T wiring and commissioning,
approach, swing side sensors 
Appendix B: Header hole preparation 
B.. Header, no preparation 
B.. Single LH header 
B.. Single header cover bottom view 
B.. Single RH header 
B.. Double header 

4
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 1
. Installation instructions
This manual provides installation instructions for
ED/ED automatic swing door operators used in
single door and pair door installations.
. Manual storage
This document must be kept in a secure place, and
accessible for reference as required.
If the door system should be transferred to another
facility, insure that this document is transferred as well.
. Dorma.com website
Manuals are available for review, download, and printing
on the Dorma.com website.
. Symbols used in these instructions
WARNING
This symbol warns of hazards which could result
in personal injury or threat to health.
NOTICE
Draws attention to important information
presented in this document.
 General information
TIPS AND RECOMMENDATIONS
Clarifies instructions or other information
presented in this document.
. Dimensions
Unless otherwise specified, all dimensions are given in
inches (“).
. Building codes and standards
ED/ED installation: observe applicable national
and local building codes.
CAUTION
This symbol warns of a potentially unsafe
procedure or situation.

5
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 2
 Product description
. Intended use
The ED and ED are electromechanical operators
used exclusively for opening and closing interior or
exterior swing doors.
The ED or ED operator is installed in a surface
mount header at customer site. The header must be
installed on an interior building surface.
For double swing doors, both operators are installed in a
single header.
. Full and low energy operators
ED is supplied as a full energy operator.
ED is supplied as a full energy operator.
• ED can be configured as a low energy operator;
Reference Chapter , Parameter F.
WARNING
To reduce risk of injury to persons, use this
ED100/ED250 operator only with automatic
swing doors that the operator is designed for.
Reference Chapter 6, Technical data.
. Arm configurations
ED and ED are both suitable for installation using:
• ED push arm
• ED pull arm with track
• ED push arm with track [application specific]*
*Does not qualify for use on a smoke or fire-rated
door.
TIPS AND RECOMMENDATIONS
Insure operator is qualified for use at the
respective smoke or fire-rated door.
Door width Door weight
ED ED
Inches mm Pounds kg Pounds kg
 .    
 .    
 .  .  
 .  .  
   .  
     
     
2.5.1 Maximum door weights based on door width
. Maximum door weights
• ED:  pounds [ kilograms]
• ED:  pounds [ kilograms]
Maximum weights are dependent on door width.
. Hardware as shipped
.. Single swing door
. Box containing surface mount header assembly for
one ED/ED operator. Included inside header:
• Accessory installation kit, either full energy or low
energy (Chapter ).
• Program switch panel (Chapter ).
• Box containing push arm or pull arm kit.
. Box containing ED or ED operator with
attached mounting base.
.. Double swing doors
. Box containing surface mount header assembly for
two ED/ED operators. Included inside header:
• Two accessory installation kits, either full energy or
low energy (Chapter ).
• Program switch panel (Chapter ).
• Two boxes, each containing a push arm or pull arm
kit.
• ED/ED operator connection cables
(Para. .).
. Two boxes, each containing an ED or ED
operator with attached mounting base.

6ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 3
. Safety instructions
This document contains important instructions for
installation of the ED/ED swing door operators.
Review these instructions thoroughly prior to
installation, and follow them carefully during installation,
commissioning, troubleshooting and maintenance.
. Door signage requirements, reference Chapter 
Proper signs and labels shall be applied and maintained on
the door controlled by the ED/ED automatic
swing door operator:
• Full power: ANSI/BHMA A.: Standard for
power operated doors.
• Low Power: ANSI/BHMA A.: Standard for
power assist and low energy power operated doors.
. Safety warnings
WARNING
Damage to equipment or incorrect equipment
operation may result from an incorrect installation.
WARNING
Hazard to mechanical processes by use of
control settings, elements, or procedures not
documented in this manual!
WARNING
Electric shock hazard!
By use of control elements, settings, or
procedures not documented in this manual!
WARNING
Work on electrical equipment and  VAC
wiring installation must be performed only by
qualified personnel!
WARNING
Metallic doors must be grounded per national
and local codes!
 Safety information
WARNING
Hand pinch point and crushing hazards at door
closing edges!
WARNING
Crushing hazards at door closing edges!
. Residual hazards
WARNING
After installation, hazards such as minor
crushing, impact with limited force, and risk to
unsupervised children may exist depending on
structural design of door area, type of door,
and any safeguards that have been
implemented.
WARNING
Hand pinch point and crushing hazards at arm
and track!
Fig. 3.2 Hazards at arm and track
Fig. 3.1 Door closing edges
Opposing
closing edge
Main
closing edge
Secondary
closing edge
Pull arm and track Push arm

7
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 4
13
8
1
10
 ED/ED Product overview
. ED/ED single swing door
Fig. 4.1.1 Header assembly with cover
1ED100/ED250
4" x 6" header
2Header cover
3Cover screws
4Program switch
panel mounting
surface
5Jamb brackets
64" x 6" header
track
7Hole for drive axle
8ED100/ED250
operator
9Hole for spring
tension
adjustment
Fig. 4.1.4 ED100/ED250 operator
1Program switch
panel DX4604
-01C, 3 ft. cable
-02C, 10 ft. cable
2Program switch,
3 position
3Exit only switch,
2 position
4Comm port for
Dorma USA, Inc
handheld
5RJ45 comm. cable
Fig. 4.1.7 Program switch panel
Fig. 4.1.3 Header with operator
Fig. 4.1.2 Header without operator
1
6
55
1
2
334
79
1
8
1 ED100/ED250
header
8ED100/ED250
operator
10 Push arm
11 Terminals for
accessory wiring
12 Bag containing
terminals and third
guide pin*
13 Mounting plate
* Included with operator
Fig. 4.1.5 Header with push arm
1
1.1
1.2
1.2
12
Fig. 4.1.6 Accessory terminals, guide pin
11
5
5
Fig. 4.1.8 RJ45 communication cable

8ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 4
. ED/ED pair swing doors
. Arm configurations
Fig. 4.2.3 Double header with operators
Fig. 4.2.2 Double header without operators
2
33
3
4
55
1
77
Fig. 4.2.1 Double header
1Double header
2Header cover
3Cover screws
4Program switch
panel
5Hole for drive axle
6Header track
7Hole for spring
tension
adjustment 66
Fig. 4.2.4 Double header with push arms
1
88
1Double header
8Push arm
9Pull arm with track
Fig. 4.2.5 Double header with pull arms
1
99
.. Arm configurations
• Push arm
• Deep push arm
• Pull arm with track
• CPD pull arm with track
• CPD push arm with track
[application specific]*
*Does not qualify for use on a smoke or
fire-rated door.
TIPS AND RECOMMENDATIONS
Reference Chapter 12 for arm
configuration detail.

9
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 4
2
3
18
20
4
5
24
21
22
6
12
11
9
8
16
15
14
23
25
26
27
17
1Power switchl
2120 VAC terminals
3Housing unit
4Drive axle
connection
5Operator (motor,
gear, spring
6Spring tension
adjustment,
closing force
84 button user
interface
9Information
display
10 Slot for internal
program switches
11 Potentiometer,
closing speed
adjustment
12 Terminal jumper
socket, push or pull
mounting
14 Slot for upgrade
cards
15 RJ45 socket, double
door operator
synchronization
16 Com 1 service
connector
17 Accessories terminal
board
18 Mounting plate
19 Customer ground
terminal
20 Guide pin
21 Ribbon cable
22 Ribbon cable socket
23 Upgrade card socket
24 Motor
25 Encoder socket and
cable
26 Motor socket and
cable
27 Control board
Fig. 4.3.1 ED100/ED250 component view 1 Fig. 4.3.2 ED100/ED250 component view 2
1
19
2
4
5
6
17
8
9
14
15
16
18
20
3
21
23
27
. ED/ED operator component view

10 ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 5
8.1
8.2
 Accessory kits, axle extension kits
. ED and ED configured for full energy accessory kit
Fig. 5.1.1 Decal kit, low energy
Fig. 5.1.3 Header mounting screw pack Fig. 5.1.4 Push arm screw kit
Fig. 5.1.5 Pull arm screw kit
1Decal, Automatic
Caution door (both
sides)
2Decal, Activate
Switch to Operate
3Decal, Push to
Operate
4Decal, Pull to
Operate
5Decal, AAADM
safety Information
label, low energy
6Decal, Do Not Enter
6Decal, Auto Door
with Arrow (label
opposite side)
7Decal, AAADM
safety Information
label, full energy
8Header mounting
screw pack
DK4608-010
8.1 #12 x 2.5 RHWSP
8.2 1/4-20 x 1.5 PHSLFP
9Push arm screw kit
DK2719-010
9.1 10-24 x 1 1/2" barrel
nut
9.2 10-24 x 1" PPHMS
10 Pull arm screw kit
DK2719-020
10.1 10-24 x 1 1/2" barrel
nut
10.2 10-24 x 1 1/4" FHSCS
11 1/4-20 x 1" FHMSP
12 1 1/2" hole plug
13 3/8" [10 mm] hole
plug
14 Communication
cable DX4607 for
program switch
panel
15 Program switch
panel DX4604
Manuals not shown
16 Installation manual
17 Service manual
18 Owner's manual
Fig. 5.1.7 Mounting base screw kit
1
2
3
4
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
shouldopen at a slow
smooth pace (4 or more
seconds), andstop withou
t
impact.
2
. Door must remainfullyopen
for a minimum of 5 seconds
before beginning toclose.
3
. Door shouldclose at a slow,
smooth pace (4or more
seconds), and stop without
impact.
4
. Inspect the floor area.It
shouldbe clean with no
loose parts that might cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signageshouldbe present
and the hardwareshould
be in good condition.
6
. Have door inspected byan
AAADM certified inspector
at least annually.
AAADM
American Association of Automatic
Door Manufacturers
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
5
DD0739-020
SAFETY INFORMATION
Automatic Swinging Doors
1
. Walk toward the door at a
normal pace. The door
shouldopen when you ar
e
about 4 feet fromthe door.
2
. Stand motionless on
threshold for at least 10
seconds. The door shoul
d
not close.
3
. Move clear ofthe area. Th
e
door should remainopenfor
at least 1.5 seconds and
shouldclose slowly and
smoothly.
4
. Repeat steps1 through 3
from other direction if door
is used for two way traffic.
5
. Inspect the floor area.It
should be clean with no
loose partsthat might caus
e
user to trip or fall. Keep
traffic path clear.
6
. Inspect door's overall
condition. The appropriat
e
signage shouldbe present.
7
. Have door inspected bya
n
AAADM certified inspecto
r
at least annually.
AAADM
American Association o f Automatic
Door Manufacture rs
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.10 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-2496
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
6
6
7
Fig. 5.1.2 Decals, full energy
12
13
Fig. 5.1.6 Hole plug kit
14
Fig. 5.1.9 Communication cable
15
Fig. 5.1.8 Program switch panel
10.1 10.2
11
9.1
9.2

11
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 5
8.1
8.2
. ED low energy accessory kit
Fig. 5.2.1 Decal kit, low energy
Fig. 5.2.4 Header mounting screw pack
Fig. 5.2.2 Push arm screw kit
Fig. 5.2.3 Pull arm screw kit
1Decal, Automatic
Caution door (both
sides)
2Decal, Activate
Switch to Operate
3Decal, Push to
Operate
4Decal, Pull to
Operate
5Decal, AAADM
safety Information
label, low energy
8Header mounting
screw pack
DK4608-010
8.1 #12 x 2.5 RHWSP
(round head wood
screw, Phillips)
8.2 1/4-20 x 1.5 PHSLFP
(pan head self
tapping, Phillips)
9Push arm screw kit
DK2719-010
9.1 10-24 x 1 1/2" barrel
nut
9.2 10-24 x 1" PPHMS
(Phillips pan head
machine screw)
10 Pull arm screw kit
DK2719-020
10.1 10-24 x 1 1/2" barrel
nut
10.2 10-24 x 1 1/4" FHSCS
(flat head socket
screw)
11 1/4-20 x 1" FHMSP
(flat head machine
screw, Phillips)
12 1 1/2" hole plug
13 3/8" [10 mm] hole
plug
14 Communication
cable DX4607 for
program switch
panel
15 Program switch
panel DX4604
Manuals not shown.
16 Installation manual
17 Service manual
18 Owner's manual
Fig. 5.2.5 Mounting base screw kit
1
2
3
4
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
shouldopen at a slow
smooth pace (4 or more
seconds), andstop withou
t
impact.
2
. Door must remainfullyopen
for a minimum of 5 seconds
before beginning toclose.
3
. Door shouldclose at a slow,
smooth pace (4or more
seconds), and stop without
impact.
4
. Inspect the floor area.It
shouldbe clean with no
loose parts that might cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signageshouldbe present
and the hardwareshould
be in good condition.
6
. Have door inspected byan
AAADM certified inspector
at least annually.
AAADM
American Association of Automatic
Door Manufacturers
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
5
12
13
Fig. 5.2.7 Hole plug kit
14
Fig. 5.2.6 Communication cable
15
Fig. 5.2.8 Program switch panel
10.1 10.2
11
9.1
9.2

12 ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 5
. Axle extension kits
Fig. 5.4.1 90 mm
5.2
5.3
Fig. 5.4.2 20 mm Fig. 5.4.3 30 mm Fig. 5.4.4 60 mm
5.4
5.5
1Flat washer
2Conical spring
3O-ring
4M8 SHCS
5.2 20 mm (13/16")
extension
5.3 30 mm (1 3/16")
extension
5.4 60 mm (2 3/8")
extension
5.5 90 mm (3 9/16")
extension

13
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 5
. Double door ED/ED operator connection cables
1Communication
cable
DX3485-010,
250 mm, 9 7./8"
DX3485-020,
1030 mm, 40 1/2"
DX3485-030,
2030 mm, 80"
2RJ45 plug
3 115 VAC power cable
DX3484-010,
69" long
DX3484-020,
95" long
DX3484-030,
134" long
Fig. 5.5.1 Communication cable
1
2
2
3
Fig. 5.5.2 115 VAC power cable

14 ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 6
 Technical data
Maximum wire size
Connector plug
screw size
 AWG
/”
Door
status
X
,,
Sr parameter
Door closed
Door open
Door closed, locked
Com, N.O., N.C.
contacts
.. Integrated functions
Hold open time:
Automatic opening dd parameter  to  s
NIght / bank dn parameter  to  s
Manual opening do parameter  to  s
Door blocking
behavior hd parameter Automatic, manual
door modes
Electric strike
delayed opening for
locking mechanism
Ud parameter  to  s
Locking
device
feedback
X
,  Motor lock
Wind load control,
maximum Fo, Fc parameters . lb f
 N
Voltage independent
braking circuit Chapter  Adjustable with
potentiometer
LED status indicators
Service manual
Green
Red
Yellow
 VDC power
Error codes
Service interval
Program and Exit
Only switches Chapter  Auto, Close, Open
Exit only; Off, On
User interface Chapter   button keypad,
 digit display
Slot for Dorma
upgrade cards Chapter  Extension of
range of functions
Interface update
Service manual Firmware update
TMP, temperature
management program
Service manual
Overload protection
IDC, initial drive control Driving phase optimization
Cycle counter CC parameter  to ,,
Power assist function hA, hF, hS
parameters
Drive support for
manual opening of
door
Push & go function PG parameter Auto opening of
door at ° open
. ED/ED Technical data
.. Required operating conditions
Ambient temperature  to  °F
Suitable for dry
rooms only
Relative air humidity:
% maximum, non-condensing
Power supply  VAC ±%, / Hz
. A maximum
Branch circuit
protection (provided
by others)
 A maximum,
dedicated branch circuit
Protection class NEMA 
Power wiring:
black, white, bare
copper (ground)
 AWG
Operating noise Maximum  db(A)
.. General specifications
Operator dimensions
(W x H x D)  /" x  / x  /"
Operator weight . lb
Internal power
supply available for
external customers
 VDC ± %, . A
Maximum door
opening angle  to ° depending on installation type
.. Inputs
Maximum wire size
Connector plug
screw size
 AWG
/”
Activation
inputs X* Interior, exterior N. O. contact
Safety
sensors X Swing, approach
sides
Night-bank
(intercom
system)
X
,
a
- VDC/
VAC +%
Night-bank
(key switch)
X
,  d parameter Configure for N.O.
or N.C. contact
Deactivation
of drive
function
X
, a d parameter Configure for N.O.
or N.C. contact
.. Outputs
TIPS AND RECOMMENDATIONS
• *X:terminal board numbers, reference
Chapter , System accessories.
• Parameters, reference Chapter .

15
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 6
Maximum power
consumption  watt
Automatic closing
torque,
lbf ft, Note 
Minimum
.
Maximum
.
Manual closing
torque, lbf ft, Note 
Minimum
.
Maximum
.
Maximum door
weight
 lb at a maximum door width of "
 lb at a maximum door width of "
Door width Minimum
 /"
Maximum
"
Door width for fire
protection  /" to ”
Maximum opening
speed, °/s 
Maximum closing
speed, °/s 
Axle extensions
[ mm] /"
[ mm]  /"
[ mm]  /"
[ mm]  /"
Reveal depth for pull
arm with track  /"
Maximum reveal
depth for pull arm
with CPD lever and
track
 /"
Reveal depth for
standard push arm  to  /"
Reveal depth for deep
push arm " minimum to  /"
Note 
Full energy / low energy
• F.E.: ED configured for full energy
• L.E.: ED configured for low energy
Note 
Speeds automatically limited depending on door
weight, set during learn cycle.
Note 
In push version of slide channel with track
installation type, forces are reduced by
approximately %.
Maximum power
consumption  watt
Automatic closing
torque,
lbf-ft, Note 
Minimum
.
Maximum
F.E. .
L.E. 
Manual closing
torque, lbf- ft, Note 
Minimum
.
Maximum
.
Maximum door
weight  lb at a maximum door width of "
Door width Minimum
 /"
Maximum
"
Maximum opening
speed, °/s, Note 
F.E. 
L.E. 
Maximum closing
speed, °/s, Note 
F.E. 
L.E. 
Axle extensions
[ mm] /"
[ mm]  /"
[ mm]  /"
Reveal depth for pull
arm with track  /"
Maximum reveal
depth for pull arm
with CPD lever and
track
 /"
Reveal depth for
standard push arm  to  /"
Reveal depth for deep
push arm " minimum to  /"
. Operating specifications
.. ED .. ED

16 ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 7
 Recommended tools and torque chart
1
5
Fig. 7.1.1 Recommended tools
. Recommended tools
1T-handle hex key, 5
mm
2Hex keys, 2.5 mm,
3 mm, 6 mm
3Screwdriver, flat
blade
4Door pressure
gauge, 0 to 35 ft - lbf
5Screwdriver, Phillips,
#2, #3
6Torque wrench,
3 to 50 ft lb min.
6.1 Metric hex key
sockets
7Open end wrench,
13 mm
8Screwdriver, flat
blade, M2 (1/16 to
3/32")
2
4
7
Fastener size ft lb
M .
M 
M 
M 
M 
. Standard tightening torque
.. Standard tightening torque
3
Fastener Drill bit size
# wood screw Hardwood
/"
Softwood
/"
# wood screw Hardwood
/"
Softwood
/"
# wood screw Hardwood
/"
Softwood
/"
/ - metal self
tapping screw /"
- barrel nut /"
. Drill bits
.. Drill bit sizes for fasteners Fig. 7.3.1 Drill bit
8
6
6.1

17
ED100/ED250 11-2017DL46143-010
dormakaba ED100/ED250 Installation instructions Chapter 8
 Operational mode overview
. ED/ED door closer modes
.. Automatic mode
Door closer mode parameter hd=.
Designed for automatic access following pulse
generation by a motion detector or pushbutton.
.. Manual mode
Door closer mode parameter hd=.
Designed for doors primarily accessed manually.
.. Power assist
• Available only in door closer mode (hd=), manual
opening. Drive support is automatically adjusted to
operator size.
• Parameter hA sets door activation angle for power
assist function. Once angle reached, drive support
provides easier manual opening of the door.
• Parameter hF, power assist function. Parameter
values greater than  provides additional opening
force.
• Parameter hS, power assist function support for
door in closed position.
. Low energy product
.. ANSI/BHMA .
ED operator is configured to meet requirements of a
low energy application per ANSI/BHMA A., U.S.
Standard for Power Assist and Low Energy Power
Operated Doors.
ED operator can be configured for full energy
operation using a full energy upgrade card.
.. Low energy power operated door
A door with a power mechanism that opens the door
upon receipt of a knowing act activating signal, does
not generate more kinetic energy than specified in
ANSI 156.19, and is closed by a power mechanism or by
other means.
Required system safety, as a low energy application, is
achieved utilizing the following design factors:
• Reduced dynamic door panel contact forces
• Reduced static door panel contact forces
• Low driving speeds
• Force limitation
TIPS AND RECOMMENDATIONS
Parameter descriptions can be found in Chapter
21; Parameters and in ED100/ED250 Service
Manual, Chapter 15.

18 ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 9
 User interface
. Overview
Fig. 9.1.1 Operator keypad and display
12 digit display
24 button keypad
.. Operator user interfaces
.  button keypad and  digit display.
•  button keypad; to select, input and
adjust door parameter values.
•  digit display; parameter values, error
and information codes.
> 3s Reset
< 3s Quit
> 3s
PRG
< 3s LEARN
Fact-Setup
> 3s
> 8s
2
5
Fig. 9.2.1 Door hinge side on right
22 digit display
5Button legend
> 3s Reset
< 3s Quit
LEARN
< 3s
> 3s
Fact-Setup
PRG
> 3s
> 8s
6
2
Fig. 9.2.2 Door hinge side on left
.  button keypad and display
Right button
. Access parameter menu,
press button >  seconds.
. Edit selected parameter.
. Save changed value.
Left button
. Cancel parameter edit
process.
. Exit parameter menu,
press button <  s.
Both buttons
together
. Acknowledge errors,
press both buttons <  s.
. Reset, press both
buttons >  s.
Up button
. Scroll through parameters
and error messages.
. Increase parameter value.
Down button
. Scroll through parameters
and error messages.
. Reduce parameter value.
. Opening pulse, press
button <  s.
. Learning cycle, press
button >  s.
. Reset with factory setting,
press button >  s (program
switches off).
. Identify operator
orientation for display
22 digit display
6Button legend
rotated 180°
12
..  button keypad
 button legend is orientated so buttons
have same function and position regardless
of operator orientation. Button legend can
be removed and rotated.
..  button keypad functions

19
ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 9
. Program switch panel
Fig. 9.3.1 Program switch panel
1Program switch
panel
2Program switch,
3 position
3Exit Only switch,
2 position
4Comm port for
Dorma USA, Inc.
handheld
9.4 Operator status LEDs
Fig. 9.4.1 Operator status LEDs
.. Operator status LEDs
Header cover must be opened to view LEDs.
. Red LED
Blinking codes are used to indicate "ln__"
information (system status or operating
conditions) or certain error codes "E__".
. Yellow LED
Maintenance interval indicator. When
illuminated, an indication the operator
system has to be serviced.
. Green LED
• On, internal  VDC power is On.
• Off, internal  VDC power is Off.
TIPS AND RECOMMENDATIONS
Details on LED status codes and
maintenance intervals can be
found in ED100/ED250 service
manual, Chapter 16, troubleshooting
chart.
1Red LED
2Yellow LED
3Green LED
4Power switch
.. Program switch control modes
• Auto, door opens automatically when one of the
activators is actuated or triggered and closes on
expiration of adjustable hold open time with no
activators or actuators triggered.
• Close, door closes automatically, or remains closed
until program switch position changed.
• Open, door opens automatically and remains open
until program switch position changed.
.. Exit only switch modes
• Off, Interior and exterior activation sensors both
active.
• On, exterior activation sensor disabled when door
fully closed. Only interior activation sensor will enable
door opening.
3 B A 1 57 57a 1 42 3 1 41 3 1 15 17 3 1 11 13 3
4a 4 1 6 3 1 3 35 3 33 34 32 31 30 99 98 97
43 3 64 63 62 1G 3
X1
X6 X9 X7
X3
X8 X10 X4 X1
3
2
4
1
1
1.1
1.2
1.2

20 ED100/ED250 11-2017DL4614-010
dormakaba ED100/ED250 Installation instructions Chapter 10
1
8 x 18 AWG 8 x 0.8 mm2 2 x 18 AWG 2 x 0.8 mm2 2 x 18 AWG 2 x 0.8 mm2
2 x 18 AWG 2 x 0.8 mm2
4 x 18 AWG 4 x 0.8 mm2 2 x 18 AWG 2 x 0.8 mm2
2 x 18 AWG 2 x 0.8 mm2
2 x 18 AWG
2 x 0.8 mm2
3 x 12 AWG
3 x 4.0 mm2115 VAC power
2
4563
7
8
9
 System accessories
. System accessory electrical connections
Fig. 10.1.1 Electrical connections, single door
.. Overview
ED/ED operators are normally used
with system accessories available from
Dorma USA, Inc. or other manufacturers.
.. Accessory electrical installation
Electrical interfaces from system
accessories used with operator must be
planned for. This includes routing of wiring
from accessories to operator.
.. System accessories, other
manufacturers
Dorma USA, Inc. cannot guarantee
compatibility for other manufacturer's
accessories. If any of these accessories are
used despite this caution, the operator's full
range of functions may be unavailable, or
the accessories may not work properly.
WARNING
Damage to operator or to
connected device is also possible!
.. Power for accessories
 VDC, . A ( watts) is available from
the operator for external consumers. This
supply has overcurrent protection. If
additional power is required, an external
power supply must be used.
.. Miscellaneous accessories
. Door status display, red, green.
10.2 System accessories
1External program
switch, mechanical
2External program
switch, electronic
3Key switch
4Pushbutton, night /
bank
5Pushbutton, interior
6Pushbutton, exterior
7Door locking device
8Manual release
switch
9ED100/ED250
header
.. Activators
Typical activators:
. Motion detectors
. Infrared safety sensors
. Pushbuttons, key switches
. Radio systems
. Smoke detectors
. Access control systems
. Telephone systems
. Intercoms
TIPS AND RECOMMENDATIONS
Refer to Paragraph 6, Technical
data for electrical interface
requirements.
.. Locking devices
Typical locking devices:
. Electric strike plates
. Electromagnetic locks
. Electric locks
To insure that operator and locking device
work safely when connected together,
locking device must comply with following:
. Operating voltage, power supply from
operator,  VDC, ± %.
. Operating voltage, external power
supply,  V DC/AC maximum.
. Locking device relay contact, maximum
load,  A.
. Electric strike plate duty factor, %
minimum.
. Motor lock duty factor, %.