Dormakaba ED100 User manual

ED100 / ED250
Low/Full Energy Swing Door Operators
(Fine cover)
Installation Instructions
DL4615-005 – 01-2020
| EN |

2ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Table of Contents
Table of contents 
 General information 
. General information 
 Product description 
. Product description 
. Handing of door 
 Safety information 
 ED / ED Product overview 
. ED / ED system 
. RH door configurations 
. LH door configurations 
. Double door configurations 
. Double egress door configurations 
. ED / ED operator 
. ED / ED operator component view 
. Axle extensions 
. Arm configurations 
. Push arm door stop - option 
. Optional full width cover kits DK 
 Accessory kits, axle extension kits 
. ED and ED configured for full
energy accessory kit 
. ED and ED low energy accessory
kit 
. Double door ED/ED operator
connection cables 
. Optional key switch panels 
 Operational mode overview 
. ED/ED door closer modes 
. Low energy product 
. Full energy product 
 Technical data 
. ED / ED Technical data 
. Operating specifications 
. Torque overview 
 User interface 
. Overview 
.  button keypad and display 
. Program switches 
. Operator status LEDs 
 System accessories 
. System accessory electrical connections 
. System accessories 
. ED / ED terminal board interfaces 
Table of contents
 ED/ED door signage 
. Full energy operator 
. Low energy operator 
. Door signage, full energy single swing
door 
. Door signage, low energy swing door 
. Door signage, full energy double door 
. Door signage, full energy double egress
door 
. Door signage, low energy double doors 
. Safety label, automatic swing doors 
. Safety label, low energy swing doors 
 Recommended tools and torque chart 
. Recommended tools 
. Standard tightening torque 
. Drill bits 
 ED / ED operator installation 
. Installation preparation 
. Installation templates, single door 
. Installation templates, double doors 
. Remove mounting plate from
ED / ED operator 
. Customer  Vac connection to
mounting plate terminal block 
. Mounting plate attachment to jamb or
wall 
. Connect customer  Vac to mounting
plate terminal block 
. Route accessory wiring to mounting plate 
. Remove protective film strips from
operator 
. Install ED / ED operator onto
mounting plate 
 Push arm installation 
. Push arm installation templates 
. Push arm installation 
. Set ED / ED operator spring
tension 
 Arm with track mount installation 
. Arm with track installation 
. Splined arm and track assemblies 
. Splined arm and track hardware 
. Slide shoe assembly 
. Install hardware into track 
. Fasten track assembly to door 
.7 Arm assembly 
.8 Arm assembly with CPD lever 
. Fasten arm to ED / ED operator 

3
ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Table of Contents
 Measure door width, reveal depth 
. Door width parameter Tb 
. Tb parameter values 
. Reveal depth parameter rd 
. rd parameter values 
 Braking circuit plug 
. Braking circuit plug position 
 Power fail closing speed 
. Set power fail closing speed 
 Parameters 
. Parameters 
 Single door first commissioning 
. First commissioning 
. Set configuration parameters 
. Full width cover option; set parameter PS,
program switch type 
. Perform learning cycle 
 Double door first commissioning 
. Separately commission active and
inactive doors 
. Set operator parameters for double door
operation 
. Connect communication cable between
operators 
 Set track bumper stop 
. Set track bumper stop position 
 Install push arm door stop 
. Install push arm door stop
(optional assembly) 
 Install door signage 
. Install door signage 
 Install cover, end caps and spindle
caps 
. Install cover and end caps 
. Install spindle caps 
 ANSI/BHMA standards 
. A. Power operated pedestrian doors 
. A. Low energy power operated
doors 
 Upgrade cards 
. Upgrade cards 
. Container module 
. Installing upgrade cards 
 Maintenance 
. Safety label, automatic swing doors 
. Safety label, low energy swing doors 
. ED / ED environment and cleaning 
. Yellow LED, service level 
. Pull arm maintenance 
. Arm fasteners – torque requirements 
. Push arm maintenance 
Appendix A - Driving parameters 
A. Driving parameters – detail 
Appendix B - Troubleshooting 
B. Information and error codes 
B. Red LED status codes 
B. Troubleshooting chart, "ln" codes 
B. Troubleshooting chart, "E" codes 
Appendix C - dormakaba handheld 
C. dormakaba handheld terminal 
C. dormakaba handheld; configuration
parameters 
C. dormakaba handheld; driving parameters 
C. dormakaba handheld; special functions
(Upgrade cards) ED / ED 
C. dormakaba handheld; diagnostics 
C. New dormakaba handheld; language
change to English 
C. dormakaba handheld; firmware update 
Appendix D - Full width cover options 
D. Full width cover installation instructions –
single door 
D. Full width cover installation instructions –
double door 
Appendix E - Wiring diagrams 
E. DX-C Key Switch Panel with RJ
connector 
E. DX-C Key Switch Panel 

4ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 1
.. Installation Instructions
This manual provides installation instructions for
ED / ED swing door operators used in single,
double door and double egress installations.
.. Manual storage
This document must be kept in a secure place, and
accessible for reference as required.
If the door system should be transferred to another
facility, insure that this document is transferred as well.
.. dormakaba.com website
Manuals are available for review, download, and printing
on the dormakaba.com/us website.
.. Dimensions
Unless otherwise specified, all dimensions are given in
both inches (“) and [mm].
.. Building codes and standards
ED / ED installation: observe applicable national
and local building codes.
 General information
. General information
.. Symbols used in these instructions.
WARNING
This symbol warns of hazards which could result
in personal injury or threat to health.
CAUTION
This symbol warns of a potentially unsafe
procedure or situation.
NOTICE
Draws attention to important information
presented in this document.
TIPS AND RECOMMENDATIONS
Clarifies instructions or other information
presented in this document.

5
ED100 / ED250 01-2020DL4615-005-
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 2
 Product description
.. Intended use.
The ED / ED are electromechanical operators
used exclusively for opening and closing interior or
exterior swing doors.
The ED or ED operator must be installed on an
interior building surface.
.. ED and ED operators.
... ED
• Supplied as a low energy operator.
(ANSI/BHMA A.).
• Configured as a full energy operator (ANSI/BHMA
A.) using parameter adjustment.
... ED
• Supplied as a low energy operator.
(ANSI/BHMA A.).
• Configured as a full energy operator (ANSI/BHMA
A.) using parameter adjustment.
.. Hardware as shipped, single swing door.
• ED / ED operator with attached mounting
base.
• Fine cover, end and spindle caps.
• Low energy or Full energy accessory installation kit
(Chapter ).
• Box containing push arm or arm with track kit
(Para. .).
.. Hardware as shipped, double swing door.
• () ED / ED operators each with attached
mounting base.
• () sets: Fine cover, end and spindle caps.
• () Low energy or Full energy accessory installation
kits (Chapter ).
• () push arm or arm with track kits (double egress,
one each) (Para. .).
Hinge Hinge
Exterior side of door
Interior side of door
Left hand door (LH)
Left hand reverse door (LHR) Right hand reverse door (RHR)
Right hand door (RH)
.. Handing of door.
. Product description
. Handing of door
Fig. 2.1.1 ED100 / ED250 operator

6ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 3
. Safety instructions.
This document contains important instructions for
installation of ED /ED swing door operators.
Review these instructions thoroughly prior to
installation, and follow them carefully during installation,
commissioning, troubleshooting and maintenance.
. Door signage requirements.
Proper signs and labels shall be applied and maintained on
the door controlled by the ED / ED swing door
operator.
• Reference Chapter , ED / ED Door Signage.
. Safety warnings.
WARNING
An incorrect installation may result in damage to
equipment or incorrect equipment operation.
WARNING
Hazard to mechanical processes by use of
control settings, elements, or procedures not
documented in this manual!
WARNING
Electric shock hazard!
By use of control elements, settings, or
procedures not documented in this manual!
WARNING
Work on electrical equipment and  Vac
wiring installation must be only be performed
by qualified personnel!
WARNING
Metallic doors must be grounded per national
and local codes!
 Safety information
WARNING
Hand pinch point and crushing hazards at door
closing edges!
WARNING
Crushing hazards at door closing edges!
. Residual hazards.
WARNING
After installation, hazards such as minor
crushing, impact with limited force, and risk to
unsupervised children may exist depending on
structural design of door area, type of door,
and any safeguards that have been
implemented.
WARNING
Hand pinch point and crushing hazards at arm
and track!
Fig. 3.1 Door closing edges
Fig. 3.3 Arm and track
Fig. 3.2 Push arm
Opposing
closing edge
Main
closing edge
Secondary
closing edge

7
ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 4
 ED / ED Product overview
. ED / ED system
Fig. 4.1.1 ED100 / ED250 hardware overview
1Mounting plate
2Spindle
3Spring tension
adjustment
44 button keypad
and 2 digit display
5Program switches
6Power switch
7Auxiliary wiring
interface terminals
8 Complete cover*
9Arm and track
assembly
10 Push arm
assembly
12
3
4
56
7
8
9
10

8ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 4
. RH door configurations
Fig. 4.3.1 RH push
Fig. 4.3.3 RH pull – track mount
Fig. 4.3.2 RH push, deep reveal
Fig. 4.3.4 RH pull, track mount, deep reveal
27” [686]
Standard width cover
0 - 8”
[0 203]
5 1/8”
[130]
2 3/4”
[70]
18”
[457]
REF
8 - 12”
[203 - 304]
5 1/8”
[130] 2 3/4”
[70]
REF
26”
[660]
2 3/4”
[70]
0 - 2 3/4”
[0 - 70]5 1/8”
[130]
2 3/4”
[70]
5 1/8”
[130]
0 - 1”
[0 - 25]

9
ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 4
. LH door configurations
Fig. 4.4.1 LH push Fig. 4.4.4 LH pull – Track mount installation –
Fig. 4.4.2 LH push, deep reveal
Fig. 4.4.3 LH push, deep reveal, full width cover
Fig. 4.3.5 RH pull as a push – track mount installation
Fig. 4.4.5 LH pull, deep reveal – track mount
Fig. 4.4.6 LH pull as a push

10 ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 4
. Double door configurations
Fig. 4.5.1 Push
Fig. 4.5.2 Pull - Track mount installation
Fig. 4.5.3 Push - deep reveal installation
Fig. 4.5.4 Pull -track mount deep reveal installation
5 1/8”
[130]
2 3/4”
[70]
0 - 2 3/4”
[0 - 70]
5 1/8”
[130]
2 3/4”
[70]
8 - 12”
[203 - 304]
5 1/8”
[130]
2 3/4”
[70]
REF
26”
[660]
0 - 8”
[0 203]
5 1/8”
[130]
2 3/4”
[70]
18”
[457]
Standard width cover
27” [686]
REF

11
ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 4
Fig. 4.5.5 Pull as push – track mount installation
0 - 2 3/4”
. Double egress door configurations
Fig. 4.6.1 LH double egress
Fig. 4.6.2 RH double egress
Standard width cover
27” [686] 0 - 8”
[0 - 203] 5 1/8”
[130]

12 ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 4
Fig. 4.5.1 ED100 / ED250 operator
2End cap, program
switches
3End cap, power
switch
11 Terminals for
accessory wiring
12 Bag containing
terminals and third
guide pin*
13 Guide pin
* Included with operator
Fig. 4.5.2 Accessory terminals, guide pin
. ED / ED operator
3
2
Fig. 4.5.4 ED900 operator end caps
Fig. 4.5.3 Standard width 27" cover
3
3SW standard
width cover
12
11
Fig. 4.5.5 Spindle cops
13
4
5
4Spindle cap
5Spindle cap

13
ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 4
1Power switch
2120 VAC terminals
3Housing unit
4Splined spindle
5Operator (motor,
gear, spring
6Spring tension
adjustment,
closing force
7Ground stud
84 button user
interface
9Information
display
10 Slot for internal
program switches
11 Potentiometer,
closing speed
adjustment
12 Terminal jumper
socket, push or pull
mounting
14 Slot for upgrade
cards
15 RJ45 socket, double
door operator
synchronization
16 Com 1 service
connector
17 Accessories terminal
board
18 Mounting plate
19 Customer ground
terminal
20 Guide pin
21 Ribbon cable
22 Ribbon cable socket
23 Upgrade card socket
24 Motor
25 Encoder socket and
cable
26 Motor socket and
cable
27 Control board
28 Program switches
Fig. 4.6.1 ED100/ED250 component view 1 Fig. 4.6.2 ED100/ED250 component view 2
. ED / ED operator component view
1
2
18
20
4
5
24
25
12
6
11
22
23
14
9
8
15
16
17
21
20
4
6
28
8
9
14
16
17
7
1

14 ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 4
Fig. 4.8.3 Splined arm with CPD lever and
track assembly, LH
. Arm configurations
1Drive arm
2.1 Adjustment shaft
tube, 225 mm
2.2 Adjustment shaft,
225 mm
3Shoe
4Axle extension
5.1 Adjustment shaft
tube, 450 mm
5.2 Adjustment shaft,
450 mm
1Drive arm
2CPD lever
3 Track
Fig. 4.8.4 Splined arm with CPD lever and
track assembly, RH
Fig. 4.8.5 Splined arm and track assembly
1Drive arm
2CPD lever
3 Track
1
5.1 5.2
3
4
1
4
2.1
2.2
3
Fig. 4.8.1 Splined push arm assembly,
225 mm
Fig. 4.8.2 Splined push arm assembly,
500 mm
. Axle extensions
Fig. 4.7.1 [20 mm]
3/4"
Fig. 4.7.2 [30 mm]
1 1/8"
Fig. 4.7.3 [60 mm]
2 3/8""
760 mm axle
extension sleeve
25447400140
860 mm axle
extension
25447801140
9M8 -1.25 x 80
SHCS
120 mm axle
extension sleeve
25447200140
220 mm axle
extension
25447601140
3M8 -1.25 x 40
SHCS
430 mm axle
extension sleeve
25447300140
530 mm axle
extension
25447701140
6M8 -1.25 x 50
SHCS 10 90 mm axle
extension sleeve
25447500140
11 90 mm axle
extension
25447901140
12 M8 -1.25 x 110
SHCS
Fig. 4.7.4 [90 mm]
3 9/16"
4
5
6
7
8
9
10
11
12
1
3
2
1
2
3
1
3
1
2
3

15
ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 4
. Push arm door stop - option
Fig. 4.9.1 Door stop assembly
11/2" thick base
plate
DC4633-002
21/4" thick base
plate
DC4633-001
3Rubber bumper
DC4633-003
4Shoulder screw
DC4633-004
5Mounting screw kit
DC4633-005
5.1 1/4 x 1 1/4" Phillips
FHS, black oxide,
SS
5.2 No. 14 x 1 1/4"
Phillips FHS for
sheet metal, zinc
plated steel
Fig. 4.9.2 Mounting screw kit
5.2
5.1
1 or 2
(4) 5.1
3
4
. Optional full width cover kits DK
.. Full width cover kit, single door
DK-X
Fig. 4.10.1 Full width cover kit DK3401-05X
1Fine cover single
DC3459-01X
3End cap set
3.1 Program switch
end cap
3.2 Power switch end
cap
3.3 Spindle cap
3.4 Spindle cap
4Mounting plate
extension
DC3468-010
5Cover bracket
DC3481-010
8dormakaba logo
plate DD4613-010
11 Program switches
with cable
DX3482-010
15 Wire retainer
DX3493-010
1
5
15
11
8
3
3.1 3.2
3.3
3.4
4
See next page for double door full width
cover kit.

16 ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapters 4 and 5
 Accessory kits, axle extension kits
. ED and ED configured for full energy accessory kit
Fig. 5.1.1 Decal kit, low energy
Fig. 5.1.2 Mounting plate screw pack Fig. 5.1.4 Push arm screw kit
Fig. 5.1.5 Arm with track screw kit
Fig. 5.1.3 Decals, full energy
10.1 10.2
9.1
9.2
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
should openat a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Doormust remain fullyopen
for a minimum of 5 seconds
beforebeginningto close.
3
. Doorshould close at a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose parts that mightcause
user to trip or fall. Keep
trafficpath clear.
5
. Inspect door‘s overall
condition. The appropriate
signage should bepresent
and the hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association o f Automatic
Door Manufacturer s
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
1
3
4
2
8
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-010
PUSH
TO OPERATE
1 DD0586-010
2DD0758-010
3DD0762-010
4DD0762-020
6Side 2, DD0739-010
6.1 Side 1, DD0739-010
7Safety Information
label, full energy
8Safety Information
label, low energy
9Side 1, DD0756-010
9.1 Side 2, DD0756-010
71/4-20 x 1" FH
machine screw
8No. 14 x 1" FH wood
screw
9Push arm screw kit
DK2719-010
9.1 10-24 x 1 1/2" barrel
nut
9.2 10-24 x 1" PPHMS
10 Pull arm screw kit
DK2719-020
10.1 10-24 x 1 1/2" barrel
nut
10.2 10-24 x 1 1/4" FHSC
Manuals not shown
18 Owner's manual
SAFETY INFORMATION
Automatic Swinging Doors
1
. Walktowardthe doorat a
normalpace. The door
should open when you ar
e
about 4 feetfrom thedoor.
2
. Standmotionlesson
threshold for at least 10
seconds. Thedoor shoul
d
not close.
3
. Moveclearofthe area.Th
e
doorshouldremainopenfor
atleast 1.5secondsand
shouldclose slowly and
smoothly.
4
. Repeat steps1through3
fromotherdirectionif door
isused fortwo waytraffic.
5
. Inspectthe floorarea.It
shouldbe cleanwith no
loose partsthatmightcaus
e
user totrip or fall.Keep
traffic pathclear.
6
. Inspectdoor's overall
condition. Theappropriat
e
signageshouldbepresent.
7
. Havedoorinspectedby a
n
AAADMcertified inspecto
r
at leastannually.
AAADM
American Association of Automatic
Door Manufacturers
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.10 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-2496
DONOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way.Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’smanual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
6
6.1
7
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
AUTOMATIC
DOOR
9CAUTION
DOOR
AUTOMATIC
DD0756-010
dormakaba
9.1
AUTOMATIC
DOOR
AUTOMATIC
DOOR
9.1
9CAUTION
DOOR
AUTOMATIC
DD0756-010
dormakaba
(12) 8
(12) 7
1
2
2
13 4
8
9
7
6
14
Fig. 4.10.2 Full width cover kit DK3401-07X
.. Full width cover kit, double door
DK-X.
1 Cover, pair
2End cap set
4Mounting plate
connectors
6Mounting plate,
pair
7dormakaba logo
8M6 x 10 mm SHS
with washer
9M6 x 10 mm PFHS
13 Program switch
14 Wire retainer

17
ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 5
. ED and ED low energy accessory kit
Fig. 5.2.1 Decal kit, low energy Fig. 5.2.4 Push arm screw kit
Fig. 5.2.5 Arm with track screw kit
1 DD0586-010
2DD0758-010
3DD0762-010
4DD0762-020
5Safety Information
label, low energy
9Push arm screw kit
DK2719-010
9.1 10-24 x 1 1/2" barrel
nut
9.2 10-24 x 1" PPHMS
(Phillips pan head
machine screw)
10 Pull arm screw kit
DK2719-020
10.1 10-24 x 1 1/2" barrel
nut
10.2 10-24 x 1 1/4" FHSCS
(flat head socket
screw)
71/4-20 x 1 " FH
machine screw
8No. 14 x 1 "FH wood
screw
14 Communication
cable DX4607 for
program switch
panel
Manuals not shown.
18 Owner's manual
14
Fig. 5.2.6 Communication cable
10.1 10.2
9.1
9.2
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
should openat a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Doormust remain fullyopen
for a minimum of 5 seconds
beforebeginningto close.
3
. Doorshould close at a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose parts that mightcause
user to trip or fall. Keep
trafficpath clear.
5
. Inspect door‘s overall
condition. The appropriate
signage should bepresent
and the hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association o f Automatic
Door Manufacturer s
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
1
3
4
2
8
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-010
PUSH
TO OPERATE
Fig. 5.2.2 Mounting plate screw pack
(12) 8
(12) 7
14
15
Fig. 5.1.6 Program switch panel
Reference Para. . for optional key switch panels.
Fig. 5.1.7 Communication cable
15 Program switch
panel DX4604
14 Communication
cable DX4607 for
program switch
panel

18 ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 5
. Double door ED/ED operator connection cables
1Communication
cable
DX3485-010,
250 mm, 9 7./8"
DX3485-020,
1030 mm, 40 1/2"
DX3485-030,
2030 mm, 80"
2RJ45 plug
3 115 VAC power cable
DX3484-010,
69" long
DX3484-020,
95" long
DX3484-030,
134" long
Fig. 5.3.1 Communication cable
1
2
2
3
Fig. 5.3.2 115 VAC power cable
2
3
2Key switch panel,
RJ45, DX4604-21C
3Key switch panel
DX4604-11C
Fig. 5.4.1 Key switch panels
Wiring diagrams:
Reference Appendix E
. Optional key switch panels

19
ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 6
 Operational mode overview
. ED/ED door closer modes
.. Automatic mode
Door closer mode parameter hd=.
Designed for automatic access following pulse
generation by a motion detector or pushbutton.
.. Manual mode
Door closer mode parameter hd=.
Designed for doors primarily accessed manually.
.. Power assist
• Available only in door closer mode (hd=), manual
opening. Drive support is automatically adjusted to
operator size.
• Parameter hA sets door activation angle for power
assist function. Once angle reached, drive support
provides easier manual opening of the door.
• Parameter hF, power assist function. Parameter
values greater than  provides additional opening
force.
• Parameter hS, power assist function support for
door in closed position.
. Low energy product
.. ANSI/BHMA .
ANSI/BHMA A., U.S. Standard for Power Assist
and Low Energy Power Operated Doors.
... ED and ED
ED and ED operators are configured to meet
requirements of a low energy application (factory
default).
.. Low energy power operated door.
A door with a power mechanism that opens the door
upon receipt of a knowing act activating signal, does
not generate more kinetic energy than specified in
ANSI 156.19, and is closed by a power mechanism or by
other means.
Required system safety, as a low energy application, is
achieved utilizing the following design factors:
• Reduced dynamic door panel contact forces
• Reduced static door panel contact forces
• Low driving speeds
• Force limitation
TIPS AND RECOMMENDATIONS
Parameter descriptions can be found in
Appendix A; Parameter detail.
. Full energy product
.. ANSI/BHMA .
ANSI/BHMA A., U.S. Standard for Power
Operated Pedestrian Doors.
... ED and ED
ED and ED operators can be configured for full
energy application by parameter adjustment.

20 ED100 / ED250 01-2020DL4615-005
dormakaba ED100 / ED250 Installation Instructions – Fine cover Chapter 7
 Technical data
Maximum wire size
Connector plug
screw size
 AWG
/”
Door
status
X
,,
Sr parameter
Door closed
Door open
Door closed, locked
Com, N.O., N.C.
contacts
.. Integrated functions
Hold open time
Automatic opening dd parameter  to  s
Optional  -  s.
Hold open time
NIght / bank dn parameter  to  s
Hold open time
Manual opening do parameter  to  s
Door blocking
behavior hd parameter Automatic, manual
door modes
Electric strike
delayed opening for
locking mechanism
Ud parameter  to  s
Locking
device
feedback
X
,  Motor lock
Wind load control,
maximum Fo, Fc parameters . lb f
 N
Voltage independent
braking circuit Chapter  Adjustable with
potentiometer
LED status indicators
Chapter 
Green
Red
Yellow
 Vdc power
Error codes
Service interval
Program and Exit
Only switches Chapter  Auto, Close, Open
Exit only; Off, On
User interface Chapter   button keypad,
 digit display
Slot for upgrade
cards Extension of functional range.
Firmware update Appendix C Firmware update
TMP, temperature
management program Overload protection
IDC, initial drive control Driving phase optimization
Cycle counter CC parameter  to ,,
Power assist function hA, hF, hS
parameters
Drive support for
manual opening of
door
Push & go function PG parameter Auto opening of
door at ° open
. ED / ED Technical data
.. Required operating conditions
Ambient temperature  to  °F [- to  C]
Suitable for dry
rooms only
Relative air humidity:
% maximum, non-condensing
Power supply  Vac ±%, / Hz
. A maximum
Branch circuit
protection (provided
by others)
 A maximum,
dedicated branch circuit
Protection class NEMA  [IP]
Power wiring:
black, white, bare
copper (ground)
 AWG
maximum
Operating noise Maximum  db(A)
.. General specifications
Operator dimensions
(W x H x D)
" x  / x  /" [ x  x  mm]
" cover standard
Operator weight . lb [ kg]
Internal power
supply available for
accessories
 Vdc ± %, . A
Maximum door
opening angle  to ° depending on installation type
.. Inputs
Maximum wire size
Connector plug
screw size
 AWG
/”
Activation
inputs X* Interior, exterior N. O. contact
Safety
sensors X Swing, approach
sides
Night-bank
(intercom
system)
X
,
a
- Vdc/Vac +%
Night-bank
(key switch)
X
,  d parameter Configure for N.O.
or N.C. contact
Deactivation
of drive
function
X
, a d parameter Configure for N.O.
or N.C. contact
.. Outputs
TIPS AND RECOMMENDATIONS
• *X:terminal board numbers, reference
Chapter , System accessories.
• Parameters, reference Chapter .