Dräger Babylog VN500 Quick start guide

D-12377-2016
Disassembly/Assembly Muffler
Open the flap by lifting the lower
edge upwards.
Close the flap.
Pull the muffler as far it will go
to the left.
Push the muffler to the
right into the socket.
Remove the expiratory valve from
the fitting.
Turn the locking ring as far as
possible to the left.
Remove and empty the water
trap container.
Fit the muffler into the socket.
Remove the muffler from
the socket.
Remove the diaphragm.
91 03 108 | 17.03-2 | AW | LE | Subject to modifications | © 2016 Drägerwerk AG & Co. KGaA
Fit the water trap container.
Fit the diaphragm onto the edge
of the expiratory valve housing.
Turn the locking ring as
far as it will go to the right
until it clicks into place.
Turn the locking ring as far as
possible to the left and push the
expiratory valve into the fitting.
Dräger Babylog® VN500
Neonatal Expiratory Valve
and Neonatal Flow Sensor
Disassembly/Assembly and Reprocessing
Disassembly/Assembly Neonatal Expiratory Valve
The muffler is only attached to the Babylog® VN500. It is only available with
an 11 mm diameter port. The Babylog® VN500 is dedicated to neonatal and
pediatric patient population.
This guideline does not replace or amend the instructions for use for Infinity Acute Care System Workstation Neonatal Care.
The instructions for use and the hospital guidelines and policies always have to be observed.

D-12377-2016
Disassembly/Assembly Neonatal Flow Sensor
Remove the breathing hoses
from the neonatal flow sensor.
Fit the breathing hoses to
the neonatal flow sensor.
Disconnect plug of the flow
sensor cable from the
neonatal flow sensor.
Connect plug of the flow
sensor cable to the
neonatal flow sensor.
Fit the insert into
the flow sensor.
Gently press the knobs on
both sides while pulling the
insert out of the neonatal
flow sensor.
Dräger Babylog® VN500
and Neonatal Expiratory Valve
Reprocessing
Neonatal Flow Sensor
Disassembly/Assembly
Before manual cleaning
prepare cleaning solution. Before
and after immersion fit a syringe
containing 20 ml of solution to
the ejector channel. Inject and
extract the solution several times.
Reprocessing of Neonatal Expiratory Valve
This guideline does not replace or amend the instructions for use for Infinity Acute Care System Workstation Neonatal Care.
The instructions for use and the hospital guidelines and policies always have to be observed.

Prepare cleaning solution.
Immerse flow sensor housing
and sensor insert bubble-free
in the cleaning solution.
Ensure that the solution flushes
all surfaces and interior spaces.
At the beginning and end of the
entire reprocessing procedure
vigorously swirl both parts for at
least one minute.
... until no cleaning agent
residues can be recognized.
For disinfection, repeat step 1 to 4 with disinfection solution.
For disinfection, repeat step 2a to 2c with disinfection solution.
Sufficiently rinse the housing and
the insert in water (preferably
drinking-water quality) ...
* The Neonatal Flow Sensor is also working with Evita® V300 and Evita Infinity® V500.
Reprocessing of ISO 15 Neonatal Flow Sensor
and Y-piece Neonatal Flow Sensor*
D-12377-2016
At the beginning of immersion
(step 1 and 2) flush each opening
of the housing with cleaning
solution using a 20 mL syringe.
At the end of immersion flush
each opening of the housing
once more with cleaning solution
using a 20 mL syringe.
Clean the housings with a lint-free
brush: Insert the brush ten times
each vertically into both ports of
Y-piece and pull it out again and
insert it ten times each diagonally
into both angles of the opening
for the sensor insert and pull it
out again.
When using Y-piece Neonatal Flow Sensor please add the steps 2a-2c to the cleaning and disinfection immersion step
(step 1 and 2), always using the corresponding cleaning or disinfection solution.
Check parts for visible soiling or
damage. Check the sensor insert
for damage to the measuring
wires and their pegs. Thoroughly
shake out residual water.
Allow the flow sensor to air dry for
at least 30 minutes.
Final check and drying for
both Flow Sensors
!
!
2a 2b 2c
Dräger Babylog® VN500
and Dräger Neonatal Flow Sensor
Reprocessing instructions
Manual cleaning and disinfection
This guideline does not replace or amend the instructions for use for Infinity Acute Care System Workstation Neonatal Care.
The instructions for use and the hospital guidelines and policies always have to be observed.

Manual cleaning
and disinfection
Machine cleaning
and disinfection
Sterilization
Reprocessing instructions overview:
D-12377-2016
housing and sensor separately
housing and sensor separately
without sensor
without sensor
sensor and housing connected
sensor and housing connected
Machine cleaning and disinfection:
Securely position the product in the basket.
Ensure the following:
– All surfaces and interior spaces can be
fl ushed completely.
– The water can drain off freely.
Sterilization:
Check the product for visible damage and replace if necessary.
For semi critical products sterilization is possible but not necessary.
For further information please refer to Instruction for Use.
Manufacturer:
Drägerwerk AG & Co. KGaA
Moislinger Allee 53–55
23558 Lübeck, Germany
Dräger Babylog® VN500
and Neonatal Flow Sensor
Reprocessing instructions
Manual cleaning and disinfection
This guideline does not replace or amend the instructions for use for Infi nity Acute Care System
Workstation Neonatal Care.
The instructions for use and the hospital guidelines and policies always have to be observed.