Dräger Savina Supplement

© Drägerwerk AG & Co. KGaA, 2019
© Drägerwerk AG & Co. KGaA, 2019
March 2020, Lübeck
Savina –
Short guide

© Drägerwerk AG & Co. KGaA, 2019
Savina –Short guide
3
This Savina short guide is intended for informational purposes only. It is not
a replacement or substitute for the Instructions for Use.
The completion of this guide does not relieve you from reading and
understanding the current versions of the instructions for use associated
with the relevant device.
It is also not a replacement for mandatory instructions or training courses.

© Drägerwerk AG & Co. KGaA, 2019© Drägerwerk AG & Co. KGaA, 2019
Savina –
System overview
4
01

© Drägerwerk AG & Co. KGaA, 2019
Savina –System overview
Front connections
5
Screen Keys for ventilation parameters
(with a display of the current values)
Red LED:
−flashes for alarms with high
priority
Yellow LED:
−Flashes for alarms with medium
priority
−Lights up for alarms with low
priority
Audio paused 2 min. key
Alarm Reset key
Lock key
LED indicating the power supply
Standby key
Rotary knob
Keys for ventilation modesConfig. key
Values key
Alarms key
Settings key
Curves key
Key for switching the
screen brightness
between bright/dark
Insp. hold key
O2Suction key
Nebul. key
Trigger LED

© Drägerwerk AG & Co. KGaA, 2019
Savina –System overview
Rear
6
Filter cover
HPO port for O2
compressed gas hose O2
COM port (serial RS232 port)
Fuse
Connection for external battery or
DC on-board power supply
Connection for power cable,
mains power fuse
Power switch for switching On or Off
LPO port for connecting
a low-pressure oxygen source,
e.g., an O2 concentrator

© Drägerwerk AG & Co. KGaA, 2019© Drägerwerk AG & Co. KGaA, 2019
Savina –
Operating concept
7
02

© Drägerwerk AG & Co. KGaA, 2019
Savina –Operating concept
Control and display unit
8
Control and display unit
1. The Rotary knob is used to select, set and confirm parameters.
2. Keys to adjust ventilation mode:
−press the corresponding key,
−press the rotary knob to confirm, the yellow LED in the key
lights up
3. Setting ventilation parameters:
−press the corresponding key, the yellow LED in the key lights up
−to make the setting, turn the rotary knob to the right or left
−press the rotary knob to confirm, the setting is accepted, the
yellow LED in the key turns off
3
1
22
3
Activating a function
Press the corresponding key. If there is one, the yellow LED in the key lights up.
Deactivating a function
Press the corresponding key again. The yellow LED in the key turns off.

© Drägerwerk AG & Co. KGaA, 2019
Savina –Operating concept
Control and display unit
9
Keys for additional functions
1. Audio paused 2 min.:suppresses the audible alarm for 2 minutes
2. Alarm Reset: resets or acknowledges an alarm message
3. Lock: key for locking and unlocking ventilation parameters
4. Standby: activates standby mode or starts the therapy
5. Curves: displays the main screen; switches between waveform
displays
6. Changes between bright and dark screen background
7. Insp. hold.: starts manual inspiration
8. O2Suction: starts or terminates the suction maneuver
9. Nebul.: switches the medication nebulizer on or off
1
4
2
3
5
6
7
8
9

© Drägerwerk AG & Co. KGaA, 2019
Savina –Operating concept
Control and display unit
10
Structure of the dialog windows
1. Active ventilation mode
2. Alarm message field
3. Depending on the dialog window:
waveforms, settings, alarm limits, measured values
4. Numerical display of measured values on the main screen
5. Message field for information and instructions
1
4
2
3
5
Dashed line:
Alarm limit Paw
Dotted line:
Pressure limitation activated, set value Pmax