Dräger X-zone 5500 User manual

i
X-zone 5500 / 5800
Notes on approval
Edition 13 - August 2021 - 90 33 499
Marking
X-zone 5500
X-zone 5800
Serial No.1
Radio approval
Only for USA (X-zone 5500/5800):
Changes or modifications not expressly approved by the party respon-
sible for compliance could void the user's authority to operate the
equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including inter-
ference that may cause undesired operation.
This device complies with part 15 of the FCC Rules. Operation is sub-
ject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interfe-
rence to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is en-
couraged to try to correct the interference by one or more of the follo-
wing measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC responsible party:
Draeger Inc.
7256 S. Sam Houston W. Parkway
Suite 100
Houston, Tx 77085 USA
phone: [phone]
e-mail: [e-mail]
Only for Canada (X-zone 5500/5800):
CAN ICES-003(B) / NMB-003(B)
Only for Japan (X-zone 5500):
Japanese Radio Law Compliance.
This device is granted pursuant to the Japanese Radio Law ( 電波法 )
This device should not be modified (otherwise the granted designation
number will become invalid)
1 Serial Number key: The third letter of the serial number specifies
the manufacturing year: M = 2019, N = 2020, P = 2021, R = 2022,
S = 2023, T = 2024, U = 2025, W = 2026, X = 2027, Y = 2028,
Z = 2029, etc. (Letters G, I, O, Q are omitted)
Example: Serial Number ARMB-0001: the third letter is M, which
means that the unit was manufactured in 2019.
0 Ex ia IIC T3 X
PO Ex ia I X
TC RU C-DE.BH02.B.00025
Dräger Safety Type: AAC 0010
23560 Lübeck, Germany
I M1 Ex ia I Ma
II 1G Ex ia IIC T4 Ga
IECEx BVS 10.0038X
BVS 10 ATEX E 047X
&7D&
Ex ia IIC T3
Ex ia d IIC T4
Class I, Zone 0,
AEx ia IIC T3 Ga
Class I, Zone 1,
AEx ia d IIC T4 Gb
Charging voltage Um<= 30 V DC
C22.2 No. 152 for % LEL reading only with MQG 00xx or
MQG 001* or MQG 01*
WARNING:
Do not charge batteries in hazardous location;
CAUTION: Read and understand manual before use
AVERTISSEMENT:
Ne pas charger batteries dans des endroits dangereux;
ATTENTION:
Lire et comprendre manuel avant utilisation
CSA 11 2367399
0158
X-zone 5800
AAC 0300
XEXT1: Charging voltage Um <= 30V DC
XEXT3 - Entity parameter of supply inputs:
19
28
37
46
13,1 2,78 1,00 1,00
Circuit Pin (+) Pin (-) Ui / V I / A Pi / W Ci / nF Li / μH
1
2
3
4
Dräger Safety, 23560 Lübeck, Germany Made in Germany
10
0158
I M1, II 1G
Ex ia I Ma, Ex ia IIC T4 Ga
BVS 10 ATEX E 047X
IECEx BVS 10.0038X
-20°C Ta +50°C
WARNING: Do not charge batteries in hazardous location;
CAUTION: Read and understand manual before use
AVERTISSEMENT: Ne pas charger batteries dans des endroits dangereux;
ATTENTION: Lire et comprendre manuel avant utilisation
li (spark):
0,850
l (therm):
0,425
Ex ia IIC T4 Ga
Class I, Zone 0,
AEx ia IIC T4 Ga
Refer to Control Drawing SE23345.
11.2367399
Radio bands
Effective ra-
diated power
(ERP)
X-zone 5500
approved in
X-zone 5800
approved in
868 MHz <5 dBm EU, SG, MY EU
433 MHz RU
915 MHz US, CA, AU US, CA
920 MHz JP



(;
4$
4%
4&
*HQHUDO7ROHUDQFH

46 
4) 
2FFXUV
0RGLILFDWLRQ7H[W
6HFWLRQIRU$$&DGGHG
UHYLVLRQVNLSSHGGXHWRWHFKQLFDOLVVXHV
&KHFNHG E\
$SSURYHGE\
3DJH
 
7LWOH
'RFXPHQW1XPEHU 5HYLVLRQ
&6$&RQWURO'UDZLQJ$$&[[$$&
6(  
$33529$/
Schutzvermerk ISO 16016 beachten.
Use of this document / contents is forbidden
without expressed written authority. All rights reserved.
Dräger
Notes
1.
Selected “Ex i”-Equipment shall have intrinsically safe outputs for
Ex ia IIC T4 Ga
Class I, Zone 1, AEx ia IIC T4 Ga
2.
Caution: Use connection XEXT1 either for charging (pin 4,5) outside the hazardous area or the
RS485 port (pin 1,2,3). Using XEXT1 for both applications at the same time is not permitted.
3.
Caution: Use connection XEXT2 either for the relay output (pin 4, 5, 6
) or the RS485 port (pin 1,2,3).
Using XEXT2 for both applications at the same time is not permitted.
4.
Warning: Live maintainance is not permitted in Zone 0 areas.
5.
Warning: Substitution of components may impair intrinsic safety.
6.
Cable Parameters:
If cable parameters are unknown, use the following parameters:
Cable Capacitance: Cc= Ccable = 60 pF/ft (200 pF/m)
Cable inductance: Lc= Lcable = 200 nH/ft (660 nH/m)
„Ex i“ - Equipment:
Uo <= 8.01 V
Io <= 0.105 A
Po <= 0.21 W
Co <= 350 nF
Lo <= 250 uH
RS485-A
RS485-B
XEXT1
Ex i Equipment
Uimax
8.01 V
>=
8.01
V
Iimax
0.105 A
>=
0.105
A
Pimax
0.21 W
>=
0.21 W
Ci
250 nF
+C
c
<=
350
nF
Li
100 uH
+L
c
<=
250
uH
Shielding optional
„Ex i“ - Equipment:
Uo <= 8.01 V
Io <= 0.105 A
Po <= 0.21 W
Co <= 350 nF
Lo <= 250 uH
RS485-A
RS485-B
Shielding optional
XEXT
2
Ex i Equipment
Uimax
8.01 V
>=
8.01
V
Iimax
0.105 A
>=
0.105
A
Pimax
0.21 W
>=
0.21 W
Ci
250 nF
+Cc<=
350
nF
Li
100 uH
+Lc <=
250
uH
2 (3)
2 (3)
Thomas Treptow
2020-12-08T11:07:20
Andreas Suerig
2020-12-08T11:58:01
Title
Document Number - Revision
Page
&6$&RQWURO'UDZLQJ$$&[[$$&
6(  
 
$33529$/
Schutzvermerk ISO 16016 beachten.
Use of this document / contents is forbidden
without expressed written authority. All rights reserved.
Dräger
AAC 00xx and AAC 03**
can be connected with non-
intrinsically safe quipment
(e.g. a PC RS485 interface)
via Z
-barriers:
Notes
1. XEXT1 and/or XEXT2 can be used
for connection of non-
intrinsically
safe equipment via Z-
barriers. As
an example the circuit diagram
shows a connetion to XEXT2.
2.
Series connection of the types
Pepperl+Fuchs Z757 with Pep-
perl+Fuchs Z966H
(BAS 01 ATEX
7005 and IECEx S06.0012 xx) is
permitted as shown.
3.
Barrier must be installed as in
struc-
ted by the manu
facturer’s control
drawing.
4.
Caution
: Use connection XEXT1
either for charging (pin 4,5)
outside
the hazardous area
or the RS485
port (pin 1, 2,
3). Using XEXT1 for
both applications at the
same time
is not permitted.
5.
Caution
: Use connection XEXT2
either for the relay output (pin 4, 5,
6) or the RS485 port (pin 1, 2,
3).
Using XEXT2 for both applications
at the same time is not permitted.
6.
Warning: Substitution of compo
-
nents may impair i
ntrinsic safety.
7.
Cable Parameters:
Use Belden
3107A, 2 x 2 AWG22. Maximum
length = 25 m = 82 ft between
AAC 00xx and the Z-barriers.
Connection of „Ex i“-Equipment in Hazardous Areas

Title
Document Number - Revision
Page
&6$&RQWURO'UDZLQJ$$&[[$$&
6(

$33529$/

Schutzvermerk ISO 16016 beachten.
Use of this document / contents is forbidden
without expressed written authority. All rights reserved.
Dräger
Wiring diagram for
connecting
non-i
ntrinsically
safe quipment to AAC 00xx
or AAC 03**
Notes
1. XEXT1 and/or
XEXT2 can be used
for connection of non-
intrinsically
safe equipment via Z-
barriers. As
an example the wiring diagram
shows a connetion to XEXT2.
2. Series switching of the types
Pepperl+Fuchs Z757 with Pep-
perl+Fuchs Z966H
(BAS 01 ATEX
7005 and IECEx S06.0012 xx) is
permitted as shown in the following
diagrams.
3. Barrier must be installed as in-
structted by the manufacturer’s
control drawing.
4. Caution
: Use connection XEXT1
either for charging (pin 4,5)
outside
the hazardous area or the
RS485
port (pin 1, 2,
3). Using XEXT1 for
both applications at the same time
is not permitted.
5. Caution
: Use connection XEXT2
either for the relay output (pin 4, 5,
6) or the RS485 port (pin 1, 2,
3).
Using XEXT2 for both applications
at the
same time is not permitted.
6. Warning: Substitution of compo
-
nents may impair intrinsic safety.
7. Cable Parameters:
Use Belden
3107A, 2 x 2 AWG22. Maximum
length = 25 m = 82 ft between
AAC 00xx and the Z-barriers.
Title
Document Number - Revision
Page
&6$&RQWURO'UDZLQJ$$&[[$$&
6(  
 
$33529$/
Schutzvermerk ISO 16016 beachten.
Use of this document / contents is forbidden
without expressed written authority. All rights reserved.
Dräger
„Ex i“ – Power Supply
(4 infallibly segregated circuits)
Uo-1, Uo-2, Uo-3, Uo-4 <= 13.10 V
Io
(spark)-1, Io (spark)-2, Io (spark)-3, Io (spark)-4 <= 0.850
A
I (therm)-1, I (therm)-2, I (therm)-3, I (therm)-4 <= 0.425 A
Po-1, Po-2, Po-3, Po-4 <= 2.78 W
Co-1, Co-2, Co-3, Co-4 <= 1 nF
Lo-1, Lo-2, Lo-3, Lo-4, <= 1 uH
Notes
1.
Caution: Only connect
galvanically isolated, intrinsically safe electric
circuits of protection type Ex ia IIC with linear output characteristics
that meet the safety parameters of AAC 03**.
All of the 4 circuits must be infallibly isolated from each other.
2.
Caution: Operation
with an intrinsically safe power supply to XEXT3
is only permitted without simultaneous inductive charg-ing, or
simultaneous power charging via the XEXT1 connection.
3.
Warning: Live maintainance is not permitted in Zone 0 areas.
4.
Warning: Substitution of components may impair intrinsic safety.
5.
Cable Parameters:
If cable parameters are unknown, use the following parameters:
Cable Capacitance: Cc= Ccable = 60 pF/ft (200 pF/m)
Cable inductance: Lc= Lcable = 200 nH/ft (660 nH/m)
The cable must maintain infallible segregation of the 4 circuits.
Supply of AAC 03** in Hazardous Areas
XEXT
3
for
each
circuit
Ex i Power
Supply
Uimax
13
.10
V
>=
Uo
Iimax
0.
850
A
>=
Io
Pimax
2
.78
W
>=
Po
Ci
1
nF
+C
c
<=
Co
Li
1
uH
+L
c
<=
Lo
Hazardous Area Safe Area
4 x 2
Use only connector CNLINKO
LP
-20-J09PE-01-
22 or equivalent
Manufacturer:
Shenzen Linko Electric Co. Ltd.
3rd Floor, Building A,
Pengzhou Industrial Park
Fuyuan 1st Road, Fuyong Town,
Baoan District SZ.China

90 33 499 - EB 4638.505 Dräger Safety AG & Co. KGaA
© Dräger Safety AG & Co. KGaA Revalstraße 1 Tel [phone]
Edition 13 - August 2021 (Edition 01 - April 2014) 23560 Lübeck, Germany Fax [phone]
Subject to alteration www.draeger.com