Draper Cinefold User manual

Assembly Instructions
Cinefold Portable Projection Screen by Draper
Frame
Hinges and
hinge locks
Handy Crank Viewing
Surface
KE Adjustme
nt
Knob
2" Min.
44" Max.
A
nti-sway stabilizers
optional with HD legs
Standard T-Leg
Frame
Snaps
Handy Crank Viewing
Surface
Bottom row of snap
studs to accept skir
t
Standard T-Leg
Heavy duty legs optional
Frame/Screen Assembly
➀Open carrying case and remove pouch containing screen
surface, and three aluminum assemblies. The largest
package is the frame. Unwrap and unfold it completely in
one direction only, locking all hinges. Frame should lie with
snaps facing up.
➁Remove surface from its envelope. With male snaps at bot-
tom, snap surface to frame. For easier surface attachment,
start in one corner, then work your way around the frame.
Make sure snaps are secure.
Please note: For steps 3-5, screen should remain on floor or
table, with surface facing up. Carefully lift screen from floor or
table to complete each step.
➂Lock corner braces.
➃Unfold leg assemblies and lock hinges. Check that ad-
justment knob is in the hole desired (upper for vertical
screen position, lower for keystone elimination). DO NOT
unfold feet at this time.
➄Attach legs to back side of vertical frame sections, as indi-
cated by the color coded markings, using Handy Cranks.
For standard screen height, match colored tapes exactly.
Height is adjustable in 6" increments.
➅Raise Cinefold to a vertical position and unfold feet. Tighten adjustment
knobs to maintain legs at desired angle. If your screen includes Heavy-
Duty Legs, unfold and lock the extensions on the backs of the feet, hinge
up to the backs of the leg, and attach with Handy Crank.
➆If Anti-Sway stabilizers are supplied with your screen, refer to illustration
and attach with Handy Cranks.
A Note About Surfaces
➀Always fold with snaps face-to-face. Do not permit screen fabric
to contact border material or snaps when folded. Store in pouch
provided.
➁Take care at all times not to permit Cinefold viewing surface
to contact any dusty or dirty area, nor any varnished or painted
object.
➂When necessary, clean Cinefold viewing surface with mild
soap and water. USE NO SOLVENTS! Surface must be com-
pletely dry before folding.
Caution
➀Read instructions through completely before proceeding; retain for future
reference.
➁Handle viewing surface with care; do not allow it to come in contact with
sharp or dirty objects.
➂Use Handy Cranks provided; failure to do so may lead to screen damage.
➃Make sure screen is level.
➄Do not write on viewing surface.
Copyright © 2007 Draper Inc. Form Cinefold_Inst07 Printed in U.S.A.
®
Caution: Beware
of pinch points.
Caution: Make sure all hinges and joints are locked
before raising screen to standing position.
Caution: Make sure screen is
placed on level surface.

Assembly Instructions
Truss-Style Cinefold Portable Projection Screen by Draper
Truss Assembly
➀Remove pouch containing viewing surface from case and set aside.
Remove all aluminum assemblies.
➁Unfold all folded aluminum assemblies completely, noting labels and
color-coded marks. Lock all hinges. Position Stage Right and Stage Left
sections in appropriate positions with snaps facing up. Top and Bottom
sections should be set with snaps facing down.
➂To increase frame rigidity, hinges on top and bottom frame sections have
rivnuts marked with red and green. Insert a Handy Crank through the
threadless rivnut (red) and tighten into the threaded rivnut (green).
➃Apply small sections marked “Stiffener Bars” to back of Bottom frame
section, using eight Handy Cranks each. Failure to use all Handy Cranks
may result in damage to screen frame. Turn Bottom frame section over so
snaps face up.
➄If your screen frame is less than 25' wide, repeat step 4 for Top frame sec-
tion. Frames 25' wide and over are equipped with a special full-width Stiff-
ener for the top frame section. To attach it, place Stiffener flat with green
rivnuts face down. Place top frame section on top of and at right angles
to Stiffener, over the green rivnuts. Insert and tighten standard Handy
Cranks. Install 45° angle braces to the Top frame section and Stiffener with
Dress-Up Kit Assembly
PLEASE NOTE: All components are labeled and color coded to
facilitate assembly.
A. Valance Bar attaches to frame with simple bayonet-style mounting.
B. Draper Bars mount to Valance Bar, bayonet-style.
C. Optional adjustable Skirt Bar is secured to frame at desired level with
positive-locking plunger mechanism. If Skirt Bar is not used, Skirt may
be snapped to bottom of viewing surface.
D. Valance, Drapes, and Skirt snap onto Mounting Bars.
Drapery
Bar
Valance Bar
Drapery
Bar
Adjustable Skirt Bar
Rigid
Tr u s s
Frame
Anti-Sway
Stabilizers
Heavy-Duty
Legs
Frame & Legs
Assemble with
Handy Cranks
Handy Crank
Caution
➀Read instructions through completely before proceeding; retain for
future reference.
➁Handle viewing surface with care; do not allow it to come in contact with
sharp or dirty objects.
➂Use Handy Cranks provided; failure to do so may lead to screen dam-
age.
➃Make sure screen is level.
➄Do not write on viewing surface.
short Handy Cranks. Turn Top frame so snaps face up.
➅Join Top and Bottom to Stage Right and Stage Left, using two Handy
Cranks on each of the four corners. Match numbers on white labels, and
keep in mind that no Handy Crank should protrude outside screen frame.
➆Remove surface from pouch. With the row of male snaps at bottom, posi-
tion screen surface over frame. Snap each of the four corners, then snap
across bottom, up sides, and across top.
➇Attach feet to inner side of legs with Handy Cranks, matching color-coded
markings. Attach legs to Stage Right and Stage Left with Handy Cranks,
matching colored tapes.
➈Raise screen to a vertical position. Add Heavy-Duty Legs and Anti-Sway
Stabilizers with Handy Cranks in the positions indicated below.
Copyright © 2008 Draper Inc. Form Cinefold_Inst08 Printed in U.S.A.
®
Caution: Beware of
pinch points.
Caution: Make sure all hinges and joints are locked
before raising screen to standing position.
Caution: Make
sure screen is
placed on level
surface.