dreambaby F820N User manual

INSTRUCTIONS
Retractable Gate
F820N (white)
F943N (black)
WARNING
WARNING– Incorrect installation can be
dangerous.
WARNING– Do not use the safety barrier if
any components are damaged or missing.
WARNING– The safety barrier must not be
fitted across windows.
WARNING– Never use this gate without
securely installed Locking Brackets and
Locking Hooks.
This safety barrier conforms to
EN1930:2011;
This safety gate is for domestic use only;
This safety gate has been designed for use
with children up to 24 months of age;
Never use with a child able to climb over or
dislodge/open the gate;
The surfaces that the gate is to be fixed to
must be suitable for the purpose and must
be structurally sound;
The clearance space between the Base of
Casing and the floor MUST NOT exceed
0.3cm (0.12in);
If the safety gate is used at the bottom of
stairs to prevent the child climbing up the
stairs, it must be placed at the front of the
lowest stair;
If the safety gate is used at the top of the
stairs to prevent child falling down the stairs,
it must not be placed on any stair below the
level of the top stair;
At the top of landing, position the gate
15cm (6in) away from the top step;
This safety gate has a manual close system;
This safety gate must NEVER be used as a
pool or pond barrier;
Never leave a child unattended.
This safety gate does not replace proper
adult supervision.
Patent No. 1/604,922
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY
AND KEEP FOR FUTURE REFERENCE
Read the entire instructions before assembling and installing this product.
If you sell or give away this product, make sure you give this instruction to the new owner.
INSTALLATION
Included
Pre-assembled
PARTS LIST
A
E
F
D
I
H
J
L
K
M
B
C
G
Optional
Spacer Sets
(sold separately)
See Accessories
Panel*
Optional
Spacer Sets
(sold separately)
See Accessories
Panel*
Have on hand a tape
measure. pencil. drill with
4mm (5/32 x1in) drill bit
and a Phillips head
screwdriver.
A Gate Panel
B Cover
C Upper Bracket (x2)
D Lower Bracket (x2)
E Upper Hook (x2)
F Lower Hook (x2)
G Locking Rod
H Screws 4x25mm (
5/32 x1in) (x16)
I Masonry/Brick Plugs (x16)
J Templates (x2)
K Base of Casing
L Top of Casing
M Release Button
Before you start
WARNING: This package contains small parts and sharp points in an
unassembled state. Keep out of reach of children. Adult assembly required.
This gate can cover
an area of up to
140cm (55in).
Includes 2 sets of mounting
brackets for convenient
'clip-on/clip-off' relocation
Optional
Accessories
(sold separately)
F821N Spacer Sets (white)
F944N Spacer Sets (black)
For use when gate is fitted to
Skirting boards / Baseboards
F895 Gate Adaptor Panel
To provide a flat surface
to install gate.
*
insi de
fram e
outs ide
fram e
E
F
2
1
c
D
F820N.F943N IM_p1-p4_BASEDv2_2016.02.26
B1 B2

Top view of gate Side view of gate
bracket
spacer
hook
spacer
skirting board
baseboard
INSTALLATION
INSTALLATION
1. Choose best location for gate
Ensure the surface you are mount the gate is structurally sound such as solid timber, brick or masonry. For plaster/gyprock surface, locate the timber
beam or stud behind and mount in this location (mounting on plaster/gyprock alone is not strong enough and not safe). Do not mount to glass.
1b. Opening direction of the gate can be changed to suit
wall wall
1a. Gate can be installed outside or inside door openings
MAX – 140cm/55in MAX – 130cm/51in
mounted
outside
opening
mounted
inside
opening
1c. If the gate is used at the bottom of the stairs
to prevent the child from climbing up the
stairs, it must be placed on the lowest stair.
1e. Make sure that the gate is mounted firmly and evenly in vertical position.
Bottom of stairs
1d. If the gate is to be used at the top of the stairs to
prevent the child from falling down the stairs, it
must not be placed on any stair below the level of
the top stair.
At the top of landing, position the gate 15cm (6in)
away from the top step.
Top of stairs
15cm
6in
1f. Skirting boards (baseboards)
If there is a skirting board (baseboard) to which the Retractable Gate is to be attached, build up the wall areas equivalent to
thickness of baseboard (skirting board) with Spacers F821N/F944N (sold separately).
1g. Adaptor Panel
To provide a flat surface to install gate.
For 1.25cm (1/2in) skirting or
baseboards use:
For 1.90cm (3/4in) skirting or
baseboards use:
A1
A1
B1
B1 B2
A2
+ +
To purchase accessories, contact Tee-Zed Products for your nearest retail outlet: [e-mail]
Accessories (sold separately)
F821N Spacer Set (white)
F944N Spacer Set (black)
A1 Bracket Spacer –
1.25cm (1/2in)
B1 Hook Spacer –
1.25cm (1/2in)
A1+A2 Bracket Spacer –
1.90cm (3/4in)
B1+B2 Hook Spacer –
1.90cm (3/4in)
F895 Gate Adaptor Panel
1.
2
B1
B2
wall

INSTALLATION
INSTALLATION
Mark position of wall Hooks and Brackets
4a 4b
Template 1 = Brackets (C, D).
Template 2 = Hooks (E, F).
• Locate the frame/stud and
overlay Bracket Template .
• Keep the Template vertical and
place the lower edge of Template
on the floor.
• Repeat step with Template on
other side of opening.
• Mark the position of the upper
and lower holes with a pencil.
Checked the
direction you
want the gate
to open / close.
Align the notch
on Top of
Casing (L) with
the arrow on
the Upper
Bracket (C) in
desired open /
close direction.
wall
outside
opening
1
2
wall
floor floor
wall
1
c
D
insid e
frame
outsi de
frame
E
F
2
E
1
c
D
inside
frame
outsi de
frame
E
F
2
inside
opening
E
F
wall
wall
floor floor
The clearance
space between the
Base of Casing
and the floor
MUST NOT exceed
0.3cm (0.12in).
0.3cm
(0.12in)
conceals
Latch
use line
on template 2
Top view of gate Side view of gate
tab
arrow
notch
mount gate
on brackets
click
4c
Align the lower
part of gate to
Lower Bracket
(D) and top of
gate to Upper
Bracket (C).
Push down gently
to click into
place.
4d
Slide Cover (B)
over Upper
Bracket (C)
until it covers
dismount Latch.
1
click
2
3
C C
C
D
B
C
L
notch
L
To mount gate
4.
use line
on template 2
wall
2.
Screw the upper and lower Brackets and Hooks (C, D, E, F) into wall or door frame using screws (H)
mounted
outside
opening
mounted
inside
opening
3.
E
F
C
D
E
F
C
D
The Cover locks
the gate in place.
It must be securely
installed at all times.
F
wall
wall
wall
wall
wall

CONTACT DETAILS
Tee-Zed acknowledges that its customers may be entitled to statutory consumer guarantees and does not seek
to exclude or limit them. These guarantees include that Tee-Zed’s products are of acceptable quality. This
Tee-Zed product is for the specific purpose detailed in the instructions and packaging and Tee-Zed considers use
outside of that purpose to be abnormal use. To the maximum extent permitted by law, Tee-Zed does not accept
any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other than in accordance with the supplied installation and
removal instructions; or
• arising under the law of tort or contract.
Made in Dongguan, China.
©2016 Tee-Zed Products Pty Ltd
Dreambaby
®
products by
www.dreambaby.com.au
www.dream-baby.co.nz
www.dreambaby.co.uk
www.youtube.com/dreambabytv
www.facebook.com/dreambabysafety
www.twitter.com/dreambabysafety
INSTALLATION
TO USE
INSTALLATION
TO REMOVE
Slide Cover (B) from Top of Casing (L).
Press dismount Latch on Upper Bracket (C)
and slide gate up.
The plastic parts are made of fibreglass-armed polyamide, Polypropylene and Polyester.
Plastic parts: Nylon & Polyoxymethylene (POM) materials.
Mesh fabric made of 40% polyester and 60% non-toxic PVC coating.
Other components are made of steel and aluminium.
The materials are used for their durability and resistance.
Spacers made of ABS (Acrylonitrile Butadiene Styrene).
COMPOSITION
• Gate must be fitted according to instructions, to ensure it works correctly.
• Regularly check gate to ensure it is fitted properly and securely. Adjust as required.
• Regularly check that brackets and hooks are securely in place.
• If gate is used outdoors, bring inside and keep out of rain, hail, snow or below freezing conditions.
• Do not use the safety gate if any components are damaged or missing.
• To clean, wipe surface with a damp cloth or sponge using mild detergent and warm water.
Never clean with abrasive, ammonia based bleach based or spirit type cleaners.
• Any additional and replacement parts should be obtained from Tee-Zed Products.
MAINTENANCE & CARE
4-1 4-2
*
conceals
latch
tab
notch
*
press
dismount
latch
*
reveal
latch
To close the gate:
Press Release Button and twist clock-wise, then pull the gate handle and
without stopping fit Locking Rod (G) into Lower and Upper Hooks (E, F).
To open gate:
Press Release Button and twist clock-wise then pull the gate handle out
from Lower and Upper Hooks (E, F).
NOTE: The noise you hear while the gate retracts is designed to alert you,
letting you know that the gate is being opened.
press
dismount
latch
E
F
B
C
C
L
L
4
For silent operation, hold Release Button down when retracting gate.
Tee-Zed Products Pty Ltd
PO Box 2022, Bondi Junction NSW 1355
Australia Tel: [phone]
[e-mail]
Tee-Zed Products (N.Z.) Ltd
PO Box 64013, Botany Town Centre, Auckland
New Zealand Tel: [phone]
[e-mail]
Tee-Zed Products Ltd
PO Box 29227, Dunfermline, KY12 2DN
United Kingdom Tel: [phone]
[e-mail]