Dsc Maxsys pc4400 User manual

PC4400 v2.0 • Installation Guide

WARNING: This manual contains information on limitations

regarding product use and function and information on the

limitations as to liability of the manufacturer. The entire

manual should be carefully read.

firealarmresources.com

WARNING Please Read Carefully

Note to Installers

This warning contains vital information. As the only individual in contact with system users, it is your

responsibility to bring each item in this warning to the attention of the users of this system.

System Failures

This system has been carefully designed to be as effective as possible. There are circumstances, however,

involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm sys-

tem of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons.

Some but not all of these reasons may be:

■ Inadequate Installation

A security system must be installed properly in order to provide adequate protection. Every installation

should be evaluated by a security professional to ensure that all access points and areas are covered. Locks

and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings

and other building materials must be of sufficient strength and construction to provide the level of protection

expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire

and/or police department is highly recommended if this service is available.

■ Criminal Knowledge

This system contains security features which were known to be effective at the time of manufacture. It is

possible for persons with criminal intent to develop techniques which reduce the effectiveness of these fea-

tures. It is important that a security system be reviewed periodically to ensure that its features remain effec-

tive and that it be updated or replaced if it is found that it does not provide the protection expected.

■ Access by Intruders

Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by

moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent

the proper operation of the system.

■ Power Failure

Control units, intrusion detectors, smoke detectors and many other security devices require an adequate

power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail.

Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a

device operates only by AC power, any interruption, however brief, will render that device inoperative while

it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations

which may damage electronic equipment such as a security system. After a power interruption has occurred,

immediately conduct a complete system test to ensure that the system operates as intended.

■ Failure of Replaceable Batteries

This system’s wireless transmitters have been designed to provide several years of battery life under normal

conditions. The expected battery life is a function of the device environment, usage and type. Ambient con-

ditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the

expected battery life. While each transmitting device has a low battery monitor which identifies when the

batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance

will keep the system in good operating condition.

■ Compromise of Radio Frequency (Wireless Devices

Signals may not reach the receiver under all circumstances which could include metal objects placed on or

near the radio path or deliberate jamming or other inadvertent radio signal interference.

■ System Users

A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary

physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is

important that all system users be trained in the correct operation of the alarm system and that they know

how to respond when the system indicates an alarm.

■ Smoke Detectors

Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of rea-

sons, some of which follow. The smoke detectors may have been improperly installed or positioned. Smoke

may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the

other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the resi-

dence or building.

Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot

sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by

carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of

flammable materials, overloaded electrical circuits, children playing with matches or arson.

Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warn-

ing to allow all occupants to escape in time to avoid injury or death.

■ Motion Detectors

Motion detectors can only detect motion within the designated areas as shown in their respective installation

instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not

provide volumetric area protection. They have multiple beams of detection and motion can only be detected

in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceil-

ings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional

or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or

any other part of the detection system will impair its proper operation.

Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness

can be reduced when the ambient temperature rises near or above body temperature or if there are intentional

or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters,

radiators, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.

■ Warning Devices

Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if

there is an intervening wall or door. If warning devices are located on a different level of the residence or

premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may

be interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appli-

ances, or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired

person.

■ Telephone Lines

If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time.

Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may

be difficult to detect.

■ Insufficient Time

There may be circumstances when the system will operate as intended, yet the occupants will not be pro-

tected from the emergency due to their inability to respond to the warnings in a timely manner. If the system

is monitored, the response may not occur in time to protect the occupants or their belongings.

■ Component Failure

Although every effort has been made to make this system as reliable as possible, the system may fail to func-

tion as intended due to the failure of a component.

■ Inadequate Testing

Most problems that would prevent an alarm system from operating as intended can be found by regular test-

ing and maintenance. The complete system should be tested weekly and immediately after a break-in, an

attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or

outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating

devices and any other operational devices that are part of the system.

■ Security and Insurance

Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm sys-

tem also is not a substitute for property owners, renters, or other occupants to act prudently to prevent or

minimize the harmful effects of an emergency situation.

Limited Warranty

Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve

months from the date of purchase, the product shall be free of defects in materials and work-

manship under normal use. During the warranty period, Digital Security Controls Ltd. shall,

at its option, repair or replace any defective product upon return of the product to its factory, at

no charge for labour and materials. Any replacement and/or repaired parts are warranted for

the remainder of the original warranty or ninety (90) days, whichever is longer. The original

owner must promptly notify Digital Security Controls Ltd. in writing that there is defect in

material or workmanship, such written notice to be received in all events prior to expiration of

the warranty period.

International Warranty

The warranty for international customers is the same as for any customer within Canada and

the United States, with the exception that Digital Security Controls Ltd. shall not be responsi-

ble for any customs fees, taxes, or VAT that may be due.

Warranty Procedure

To obtain service under this warranty, please return the item(s) in question to the point of pur-

chase. All authorized distributors and dealers have a warranty program. Anyone returning

goods to Digital Security Controls Ltd. must first obtain an authorization number. Digital

Security Controls Ltd. will not accept any shipment whatsoever for which prior authorization

has not been obtained.

Conditions to Void Warranty

This warranty applies only to defects in parts and workmanship relating to normal use. It does

not cover:

• damage incurred in shipping or handling;

• damage caused by disaster such as fire, flood, wind, earthquake or lightning;

• damage due to causes beyond the control of Digital Security Controls Ltd. such as excessive

voltage, mechanical shock or water damage;

• damage caused by unauthorized attachment, alterations, modifications or foreign objects;

• damage caused by peripherals (unless such peripherals were supplied by Digital Security

Controls Ltd.);

• defects caused by failure to provide a suitable installation environment for the products;

• damage caused by use of the products for purposes other than those for which it was

designed;

• damage from improper maintenance;

• damage arising out of any other abuse, mishandling or improper application of the products.

Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty

after a reasonable number of attempts will be limited to a replacement of the product, as the

exclusive remedy for breach of warranty. Under no circumstances shall Digital Security Con-

trols Ltd. be liable for any special, incidental, or consequential damages based upon breach of

warranty, breach of contract, negligence, strict liability, or any other legal theory. Such dam-

ages include, but are not limited to, loss of profits, loss of the product or any associated equip-

ment, cost of capital, cost of substitute or replacement equipment, facilities or services, down

time, purchaser’s time, the claims of third parties, including customers, and injury to property.

Disclaimer of Warranties

This warranty contains the entire warranty and shall be in lieu of any and all other war-

ranties, whether expressed or implied (including all implied warranties of merchantabil-

ity or fitness for a particular purpose) And of all other obligations or liabilities on the

part of Digital Security Controls Ltd. Digital Security Controls Ltd. neither assumes

responsibility for nor authorizes any other person purporting to act on its behalf to

modify or to change this warranty, nor to assume for it any other warranty or liability

concerning this product.

This disclaimer of warranties and limited warranty are governed by the laws of the

province of Ontario, Canada.

WARNING: Digital Security Controls Ltd. recommends that the entire system be completely

tested on a regular basis. However, despite frequent testing, and due to, but not limited to,

criminal tampering or electrical disruption, it is possible for this product to fail to perform as

expected.

Installer’s Lockout

Any products returned to DSC which have the Installer’s Lockout option enabled and exhibit

no other problems will be subject to a service charge.

Out of Warranty Repairs

Digital Security Controls Ltd. will at its option repair or replace out-of-warranty products

which are returned to its factory according to the following conditions. Anyone returning

goods to Digital Security Controls Ltd. must first obtain an authorization number. Digital

Security Controls Ltd. will not accept any shipment whatsoever for which prior authorization

has not been obtained.

Products which Digital Security Controls Ltd. determines to be repairable will be repaired and

returned. A set fee which Digital Security Controls Ltd. has predetermined and which may be

revised from time to time, will be charged for each unit repaired.

Products which Digital Security Controls Ltd. determines not to be repairable will be replaced

by the nearest equivalent product available at that time. The current market price of the

replacement product will be charged for each replacement unit.

firealarmresources.com

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

PC4400 connected to a serial printer . . . . . . . . .1

PC4400 connected to a DVAC network . . . . . .1

3. Installing the PC4400 . . . . . . . . . . . . . . . . . . . . . .1

3.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . .1

3.2 Mounting the Cabinet . . . . . . . . . . . . . . .1

3.3 Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

3.4 PC4400 Hookup Diagram . . . . . . . . . . . .2

3.5 Applying Power . . . . . . . . . . . . . . . . . . . .2

4. Enrolling the Module. . . . . . . . . . . . . . . . . . . . . .3

5. Programming the Module. . . . . . . . . . . . . . . . . .3

5.1 Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . .3

5.2 DVAC Options . . . . . . . . . . . . . . . . . . . . .3

5.3 DVAC Identifiers . . . . . . . . . . . . . . . . . . .3

5.4 Default DVAC . . . . . . . . . . . . . . . . . . . . . .6

5.5 Trouble Conditions. . . . . . . . . . . . . . . . . .6

Programming Worksheets . . . . . . . . . . . . . . . 7

Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

DVAC Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Default DVAC Programming . . . . . . . . . . . . . . . . . 7

DVAC Identifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Zone X Alarm/Restore. . . . . . . . . . . . . . . . . . . . . . . . . .8

DVAC Identifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Zone X Trouble/Restore . . . . . . . . . . . . . . . . . . . . . . . .9

Zone X Fault/Restore. . . . . . . . . . . . . . . . . . . . . . . . . .10

Module Tamper/Restore. . . . . . . . . . . . . . . . . . . . . . .11

Priority Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Openings and Closings by User . . . . . . . . . . . . . . . . .12

Miscellaneous Openings and Closings . . . . . . . . . . .13

Partition Openings and Closings . . . . . . . . . . . . . . . .13

System Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . .13

PC4204 Troubles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Fire Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Wireless – Low Batter. . . . . . . . . . . . . . . . . . . . . . . . . .14

Wireless – Low Battery. . . . . . . . . . . . . . . . . . . . . . . . .14

Police Code (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

DVAC Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

DVAC Identifiers . . . . . . . . . . . . . . . . . . . . . . 15

Function Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Alarm Function Bytes . . . . . . . . . . . . . . . . . . . .15

Trouble Function Bytes . . . . . . . . . . . . . . . . . . .15

Bypass Function Bytes . . . . . . . . . . . . . . . . . . . .16

Supervisory Function Bytes . . . . . . . . . . . . . . .16

Opening and Closing Function Bytes . . . . . . .16

Miscellaneous Function Bytes . . . . . . . . . . . . .17

7E/FE : Specific Message Function Byte. . . . .17

firealarmresources.com

1. Introduction

Table of Contents