DSC Envoy NT9005EU Operating instructions

NT9005 EU V1.0
32 ZONE SECURITY SYSTEM
Compatible with DLS2002 downloading software
Installation & Programming Guide
WARNING: This manual contains information on limitations regarding product use and function and
information on the limitations as to liability of the manufacturer. Read the entire manual carefully.
firealarmresources.com

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls
Ltd. could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interfer-ence in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful in-
terference to radio or television reception, which can be deter-mined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the follow-
ing measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How to Identify and
Resolve Radio/Television Interference Problems". This booklet is available from the U.S.
Government Printing Office, Wash-ington D.C. 20402, Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a
label that contains, among other information, the FCC registration number and ringer equiv-
alence number (REN) for this equipment. If requested, this number must be provided to the
Telephone Company.
FCC Registration Number: F53CAN-36358-AL-E
REN: 0.1B
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
A compliant telephone cord and modular plug is provided with this product. It is designed to
be connected to a compatible modular jack that is also compliant. See installation instructions
for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone
line. Excessive RENs on a telephone line may result in the devices not ringing in response to
an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To
be certain of the number of devices that may be connected to a line, as determined by the total
RENs, contact the local Telephone Company. For products approved after July 23, 2001, the
REN for this product is part of the product identifier that has the format
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point
(e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
Incidence of Harm
If the NT9005 equipment causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if ad-
vance notice is not practical, the Telephone Company will notify the customer as soon as pos-
sible. Also, you will be advised of your right to file a complaint with the FCC if you believe
it is necessary.
Changes in Telephone Company Equipment or Facilities The Telephone Company may make
changes in its facilities, equipment, operations or procedures that could affect the operation of
the equipment. If this happens the Telephone Company will provide advance notice in order
for you to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment NT9005 for repair or warranty information,
please contact the facility indicated below. If the equipment is causing harm to the telephone
network, the Telephone Company may request that you disconnect the equipment until the
problem is solved. This equipment is of a type that is not intended to be repaired by the end
user.
Simplex Time Recorder Co. 100 Simplex Drive, Westminster MA 01441-0001 USA, Tel:
[phone]
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility com-
mission, public service commission or corporation commission for information.
Alarm dialing equipment must be able to seize the telephone line and place a call in an emer-
gency situation. It must be able to do this even if other equipment (telephone, answering sys-
tem, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing
equipment must be connected to a properly installed RJ-31X jack that is electrically in series
with and ahead of all other equipment attached to the same telephone line. Proper installation
is depicted in the figure below. If you have any questions concerning these instructions, you
should consult your telephone company or a qualified installer about installing the RJ-31X
jack and alarm dialing equipment for you.
Telephone
Computer
Telephone
Telephone
Fax Machine
Alarm Dialing
Equipment
RJ-31X
Jack Unused
RJ-11 Jack
Telephone
Line
Network
Service
Provider's
Facilities
Customer Premises Equipment and Wiring
Unused
RJ-11 Jack
Network
Demarcation
Point Answering
System
firealarmresources.com

IMPORTANT:
1. This Manual shall be used in conjunction with the Installa-
tion Manual of the used Power Supply (NT9005 Trans-
former Kit - AC/AC Adaptor).
2. This equipment, Alarm Controller NT9005 shall be
installed and used within an environment that provides
the pollution degree max 2 and overvoltages category II
NON HAZARDOUS LOCATIONS, indoor only. The equip-
ment is FIXED and PERMANENTLY CONNECTED and is
designed to be installed by service persons only; [service
person is defined as a person having the appropriate tech-
nical training and experience necessary to be aware of
hazards to which that person may be exposed in perform-
ing a task and of measures to minimize the risks to that
person or other persons.].
3. The connection to the mains supply must be made as per
the rules and regulations of the local authorities: In the
UK as per BS6701. An appropriate disconnect device
must be provided as part of the building installation.
Where it is not possible to rely on the identification of the
NEUTRAL in the AC MAINS SUPPLY, the disconnecting
device must disconnect both poles simultaneously (LINE
and NEUTRAL). The device shall disconnect the supply
during servicing.
4. Equipment enclosure must besecured to the building
structure before operation.
5. Regarding the power supply it must be permanently con-
nected, fail safe, with double or reinforced insulation
between primary and secondary circuits. In EU countries it
must meet the applicable requirements of the Low Volt-
age Directive and protected as per the EN60950-1: 2001
Standard requirements. In all other countries, it must be
of an approved type acceptable to the local authorities.
6. Internal wiring must be routed in a manner that prevents:
• Excessive strain on wire and on terminal connections;
• Loosening of terminal; connections;
• Damage of conductor insulation.
7. Disposal of the used batteries shall be made according to
the waste recovery and recycling regulations applicable to
the intended market.
8. Disconnect the TELEPHONE CONNECTION before servic-
ing!
Table of Contents
Chapter 1: Description & Operation . . . . . 1
1-1 System Overview . . . . . . . . . . . . . . . . . . . . . 1
1-2 System Specifications . . . . . . . . . . . . . . . . . 2
1-3 Modules and Devices . . . . . . . . . . . . . . . . . . 3
1-4 NT9005 Label & Console . . . . . . . . . . . . . .4
1-5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 2: Installation . . . . . . . . . . . . . . . . 7
2-1 Installation Procedure. . . . . . . . . . . . . . . . . . 7
2-2 NT9005 Installation . . . . . . . . . . . . . . . . . . . 8
2-3 System Wiring . . . . . . . . . . . . . . . . . . . . . . . 9
2-4 Wireless Device Placement . . . . . . . . . . . .11
Chapter 3: Programming . . . . . . . . . . . . . 12
3-1 Programming Overview . . . . . . . . . . . . . . . 12
3-2 Conventions Used . . . . . . . . . . . . . . . . . . . 12
3-3 [*] Functions . . . . . . . . . . . . . . . . . . . . . . . 13
Chapter 4: Flash Programming . . . . . . . 18
Chapter 5: Advanced Programming . . . 20
5-1 Section Overview. . . . . . . . . . . . . . . . . . . . 20
Appendix A: Reporting Codes . . . . . . . . 47
Appendix B: Smoke Detector
Placement. . . . . . . . . . . . . . . . . . . . . . . . . 50
Appendix C: Door/Window Contacts. . . 51
Appendix D: WLS904P Wireless
Motion Detector . . . . . . . . . . . . . . . . . . . . 52
OPERATING instructions shall be made available to the USER.
firealarmresources.com

Limited Warranty
Digital Security Controls warrants the original purchaser that for a period of
twelve months from the date of purchase, the product shall be free of defects
in materials and workmanship under normal use. During the warranty
period, Digital Security Controls shall, at its option, repair or replace any
defective product upon return of the product to its factory, at no charge for
labour and materials. Any replacement and/or repaired parts are warranted
for the remainder of the original warranty or ninety (90) days, whichever is
longer. The original purchaser must promptly notify Digital Security Con-
trols in writing that there is defect in material or workmanship, such written
notice to be received in all events prior to expiration of the warranty period.
There is absolutely no warranty on software and all software products are
sold as a user license under the terms of the software license agreement
included with the product. The Customer assumes all responsibility for the
proper selection, installation, operation and maintenance of any products
purchased from DSC. Custom products are only warranted to the extent
that they do not function upon delivery. In such cases, DSC can replace or
credit at its option.
International Warranty
The warranty for international customers is the same as for any customer
within Canada and the United States, with the exception that Digital
Security Controls shall not be responsible for any customs fees, taxes, or
VAT that may be due.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question
to the point of purchase. All authorized distributors and dealers have a
warranty program. Anyone returning goods to Digital Security Controls
must first obtain an authorization number. Digital Security Controls will
not accept any shipment whatsoever for which prior authorization has not
been obtained.
Conditions to Void Warranty
This warranty applies only to defects in parts and workmanship relating to
normal use. It does not cover:
• damage incurred in shipping or handling;
• damage caused by disaster such as fire, flood, wind, earthquake or
lightning;
• damage due to causes beyond the control of Digital Security Controls
such as excessive voltage, mechanical shock or water damage;
• damage caused by unauthorized attachment, alterations, modifications
or foreign objects;
• damage caused by peripherals (unless such peripherals were supplied
by Digital Security Controls);
• defects caused by failure to provide a suitable installation environment
for the products;
• damage caused by use of the products for purposes other than those
for which it was designed;
• damage from improper maintenance;
• damage arising out of any other abuse, mishandling or improper appli-
cation of the products.
Items Not Covered by Warranty
In addition to the items which void the Warranty, the following items shall
not be covered by Warranty: (i) freight cost to the repair centre; (ii) prod-
ucts which are not identified with DSC's product label and lot number or
serial number; (iii) products disassembled or repaired in such a manner as
to adversely affect performance or prevent adequate inspection or testing
to verify any warranty claim. Access cards or tags returned for replace-
ment under warranty will be credited or replaced at DSC's option. Prod-
ucts not covered by this warranty, or otherwise out of warranty due to age,
misuse, or damage shall be evaluated, and a repair estimate shall be pro-
vided. No repair work will be performed until a valid purchase order is
received from the Customer and a Return Merchandise Authorisation
number (RMA) is issued by DSC's Customer Service.
Digital Security Controls’s liability for failure to repair the product under
this warranty after a reasonable number of attempts will be limited to a
replacement of the product, as the exclusive remedy for breach of war-
ranty. Under no circumstances shall Digital Security Controls be liable for
any special, incidental, or consequential damages based upon breach of
warranty, breach of contract, negligence, strict liability, or any other legal
theory. Such damages include, but are not limited to, loss of profits, loss
of the product or any associated equipment, cost of capital, cost of substi-
tute or replacement equipment, facilities or services, down time, pur-
chaser’s time, the claims of third parties, including customers, and injury
to property. The laws of some jurisdictions limit or do not allow the dis-
claimer of consequential damages. If the laws of such a jurisdiction apply
to any claim by or against DSC, the limitations and disclaimers contained
here shall be to the greatest extent permitted by law. Some states do not
allow the exclusion or limitation of incidental or consequential damages,
so that the above may not apply to you.
Disclaimer of Warranties
This warranty contains the entire warranty and shall be in lieu of any and
all other warranties, whether expressed or implied (including all implied
warranties of merchantability or fitness for a particular purpose) and of all
other obligations or liabilities on the part of Digital Security Controls.
Digital Security Controls neither assumes responsibility for nor authorizes
any other person purporting to act on its behalf to modify or to change this
warranty, nor to assume for it any other warranty or liability concerning
this product.
This disclaimer of warranties and limited warranty are governed by the
laws of the province of Ontario, Canada.
WARNING: Digital Security Controls recommends that the entire sys-
tem be completely tested on a regular basis. However, despite frequent
testing, and due to, but not limited to, criminal tampering or electrical
disruption, it is possible for this product to fail to perform as expected.
Out of Warranty Repairs
Digital Security Controls will at its option repair or replace out-of-war-
ranty products which are returned to its factory according to the following
conditions. Anyone returning goods to Digital Security Controls must first
obtain an authorization number. Digital Security Controls will not accept
any shipment whatsoever for which prior authorization has not been
obtained.
Products which Digital Security Controls determines to be repairable will
be repaired and returned. A set fee which Digital Security Controls has
predetermined and which may be revised from time to time, will be
charged for each unit repaired.
Products which Digital Security Controls determines not to be repairable
will be replaced by the nearest equivalent product available at that time.
The current market price of the replacement product will be charged for
each replacement unit.
firealarmresources.com

1
Chapter 1: Description & Operation
1-1 System Overview
The NT9005 is a full-featured, wireless security system
designed for fast and easy installation. The system
may include any of the following components (refer
to figure 1, System Overview):
• NT9005 control unit.
• NT9204 Keybus interface/4 programmable outputs
• 32 wireless detectors (maximum).
• 16 wireless keys (maximum).
• Connection to a central monitoring station.
• DLS2002 (downloading software).
MLR2
WLS904P(L)-433
WS4916
DLS2002 (Downloading Software)
Via PC-Link or Modem
WS4939
LED
firealarmresources.com

Description & Operation
2
1-2 System Specifications
The NT9005 system supports up to 32 system users.
The system can be programmed using the keypad on
the NT9005 control unit, or using DLS2002 down-
loading software and a computer. If you program the
system from the NT9005 control unit, basic zone
enrollment and programming can be performed using
Flash Programming. See Chapter 4: Flash Program-
ming
Flexible Zone Configuration:
• 32 fully programmable zones
• 28 zone types, 8 programmable zone options
• Connect up to 2 hardwired zones
• Connect up to 2 main board PGM outputs
Access Codes:
• 38 access codes: 32 user codes, 1 master code, 2
supervisor codes, 2 duress codes, and 1 mainte-
nance code
EEPROM Memory:
• Will not lose programming or system status on
complete AC and battery failure
Power Requirements:
• Plug-in transformer = 9 VAC, 20 VA
• Battery = 6 volt, 3.5 Ah minimum, rechargeable
sealed lead acid (provides more than 24 Hrs
standby operation)
Digital Communicator Specifications:
• Supports SIA, Contact ID, Pager, 10 bps and 20 bps
formats, and Residential dial
• Split reporting of selected transmissions to each
telephone number
• 3 programmable telephone numbers
• 2 system account codes
• DTMF and pulse dialing
• DPDT line seizure
• Anti-jam detection
System Supervision Features
The NT9005 continuously monitors potential trouble
conditions including:
• Trouble by zone
• Telephone line trouble
• Low battery condition
• Loss of internal clock
• Tamper by zone
• Failure to communicate
False Alarm Prevention Features
• Audible exit delay
• Audible exit fault
• Urgency on entry delay
•Quickexit
• Swinger shutdown
• Recent closing transmission
• Communication delay
• Rotating keypress buffer
Additional Features
• Keypad-activated alarm output and communicator
test
• Keypad lockout
• 128-event buffer, time and date stamped
• Uploading/downloading capability
firealarmresources.com

1-3 Modules and Devices
3
1-3 Modules and Devices
Refer to the relevant installation manuals for specifica-
tions, installation and operation of the following mod-
ules and devices.
NT9204 Power Supply/Output Module
Provides 4 programmable 1.0 Ampere outputs (PGMs).
Fully supervised for tamper, AC trouble, low battery, and
auxiliary supply trouble.
WLS904PL-433 Wireless Motion Detector
Four detection patterns selectable with interchange-
able lenses. High traffic shutdown and adjustable sen-
sitivity. This device is fully supervised for tamper,
device fault, and low battery.
WLS912/(L)-433 Wireless Glassbreak Detector
Detects float, plate, tempered, wired, and laminated
glass breakage up to a distance of 20ft (6 m). Do not
mount the detector closer than 3.3 ft/1m from the pro-
tected glass. Sensitivity can be adjusted for specific envi-
ronments and glass types. This device is fully supervised
for tamper, device fault, low battery, low sensitivity.
WLS925L-433 Wireless Universal Transmitter
Low profile wireless transmitter - Can be used for wire-
less door or window contact or terminal connection for
external contacts. This device is fully supervised for
tamper, device fault, low battery, open and closed.
WLS935L-433 Wireless Door/Window Transmitter
Can be used for wireless door or window contact with
a terminal connection for external contacts. This
device is powered by a lithium battery and is fully
supervised for tamper, device fault, low battery, open
and closed.
WS4916 Wireless Smoke Detector
This is a wireless photoelectric smoke detector with a
fixed temperature heat detector and an internal piezo-
electric alarm. This device is fully supervised for
tamper, device fault, low battery, low sensitivity.
WS4939-433 Wireless Key
Provides 4 programmable buttons for functions such
as Stay Arm, Away Arm, Disarm, Fire, Auxiliary and
Panic functions.
DLS2002 Downloading Software
Enables the installer to program or monitor the system
with a computer, modem and telephone line or locally
using a computer and PC-Link.
firealarmresources.com

Description & Operation
4
1-4 NT9005 Labels & Console
The NT9005 system comes with peel off instructions
which list the Flash Programming steps for quick
setup. Remove this label after installation. Refer to
Chapter 4: ‘Flash Programming’, if required.
The console consists of a fixed message LCD, 3 status
lights (Ready, Armed and Trouble), on-board buzzer,
12 digit keypad, 3 specialized priority keys (Fire, Auxil-
iary, and Panic), and 5 programmable function keys.
Refer to Figure 2, ‘LCD Display’ and Figure 3, ‘Con-
trols & Indicators’ for details.
1-5 Operation
In all operating modes, the system monitors zones for
device faults, tampers and low battery indications.
System standby battery voltage is monitored, under
load, at four minute intervals and telephone line volt-
age is monitored every 10 seconds. During an AC fail-
ure, battery voltage is monitored continuously.
The system continuously monitors the keypad for
access codes, function keys, priority keys and [*] pro-
gramming entry.
☞Detailed explanations of all programming
options and the defaults can be can be found
in Chapter 3:Programming sections [000] to
[999]
☞Refer to Figure 3 for an overview of function
keys and priority keys. Refer to Chapter 3:sec-
tion [000] for function key programming
options. Refer to Chapter 3: [*][6], Program-
ming and sections [006] – [008] for access
codes programming.
1-5.1 Start-up
• When power is first applied to the system the fol-
lowing will occur:
• All icons on the LCD will be displayed for two sec-
onds and the buzzer will sound five beeps.
• All zones will be bypassed for two minutes. This
will allow the devices on the system to settle with-
out causing false alarms. Zones unrestored after
two minutes will be detected as open.
• A 6 Hour DLS Window will be enabled. This will
permit a remote computer with downloading soft-
ware (DLS) and a modem to telephone the unit
and download programming. Refer to sections
[401]-[406].
•ATrouble will be generated indicating that the
time displayed is incorrect. The time must be set to
clear this fault. Refer to [*][6][1] in Chapter 3:[*]
Functions.
1-5.2 Operating Modes
The system operates in three modes: base mode
which includes all armed and disarmed states; User
programming mode; and Installer’s mode. There are
three disarmed states in base mode. In these states
only 24-Hr zones and fire zones are armed and moni-
tored. See ‘Zone Definitions’ sections [001] to [004] in
Chapter 5:Advanced Programming.
Ready to Arm - (Ready light is ON). Entering an
access code will arm the system. All [*] functions can
be accessed (see ‘[*] Functions’ in Chapter 3: Pro-
gramming).
Ready to Force Arm - (Ready light is ON), Entering
an access code will force arm the system. Open zones
will be bypassed and the ‘Bypass’ icon will be dis-
played. To make a zone force armable, zone attribute
[5] must be enabled in sections [101]-[132] in
Chapter 5:Advanced Programming or the zone
definition must have that attribute on by default. See
sections [101] to [132] in Chapter 5: Advanced
Programming. All [*] Functions can be accessed in
this mode.
Not Ready to Arm - (Ready Light OFF), Open zones
are not force armable. Zones must be closed (restored)
before the systrem can be armed. All [*] functions
excluding arming functions can be accessed.
firealarmresources.com

1-5 Operation
5
Figure 2 - LCD Display
1 7-segment Displays 1 and 2 – These two 7-segment
displays indicate the hour digits when the local clock is
active, and identify the zone when the OPEN or
ALARM icons are active. These two displays scroll one
zone per second from the lowest zone number to the
highest when scrolling through zones.
2:(Colon)– This icon is the hours/minutes divider when
the local clock is active.
3 7-segment Displays 3 and 4 – These two 7-segment
displays are the minute digits when the local clock is
active.
41to8– These icons are used to identify troubles to the
user. Enter [*][2] to view troubles. In Installer’s Program-
ming, they indicate hexadecimal, decimal, and 8-bit
toggle fields found in Flash and Advanced program-
ming.
5Memory– Indicates that there are alarms in memory.
6 Bypass – Indicates that there are zones automatically
or manually bypassed.
7Program– indicates that the system is in Installer’s Pro-
gramming, or the keypad is busy.
8Away– Indicates that the panel is armed in the Full Set
mode. It will turn on at the beginning of the Exit Delay.
9Fire– Indicates that there are fire alarms in memory.
10 Stay – Indicates that the panel is armed in the Part Set
mode. It will turn on at the beginning of the Exit Delay.
11 Chime – This icon turns on when [*][4] is pressed to
enable Door Chime on the system. It will turn off
when [*][4] is pressed again to disable Door Chime.
12 AM, PM – This icon indicates that the local clock is dis-
playing 12-Hr. time. These icons will not be on if the
system is programmed for 24-Hr. time.
13 ALARM – This icon is used with 7-segment displays 1
and 2 to indicate zones in alarm on the system. When
a zone is in alarm, the ALARM icon will turn on, and 7-
segment displays 1 and 2 will scroll through the zones
in alarm.
14 OPEN – This Icon is used with 7-segment displays 1
and 2 to indicate violated zones (not alarm) on the sys-
tem. When zones are opened, the OPEN icon will turn
on, and 7-segment displays 1 and 2 will scroll through
the violated zones.
Figure 3 - Controls & Indicators
15 Buzzer - The buzzer provides an audible indication of
alarm, trouble, programming and status of the system.
16 Status Indicators
Ready - Indicates that the system is ready to be
armed or programmed.
Armed - Indicates that the system is armed in Stay
or Away mode.
Trouble - Indicates that the system has a trouble.
17 Priority Keys - The function of priority keys can not be
modified apart from enabling or disabling the keys. The
keys must be held and pressed for 2 seconds to activate
the function. When activated, a reporting code is sent
to the central monitoring station.
18 Keypad - Digits (0-9) - are used to enter decimal
and hexadecimal data.
Keypad - Digit (*) is used to enter [*] Star functions.
All user and installer functions including Flash and
Advanced programming are entered using this key. See
Chapter 3:‘[*] Functions’. The [*] key also enables the
installer/user to toggle between decimal and hexadeci-
mal data entry. To enter hexadecimal ‘A’ through ‘F’,
Press [*][1 through [6]. When finished entering hexa-
decimal numbers, enter [*] again to return to decimal
mode. See Chapter 3:Programming.
Keypad - Digit (#) is the equivalent of the Escape key
on a computer. It enables the installer to escape from
or terminate the the current programming section.
19 Function Keys - may be customized to perform 21
different functions with 8 definable options for each
function. See section [000] for a detailed explanation
of these and other options available.
3
6
9
8
5
2
1
4
7
*
0#
Ready Trouble Armed
Stay
Aw ay
Chime
Interior
Exit
17
16
15
18
19
firealarmresources.com

Description & Operation
6
Stay Armed - (Ready light is OFF, Stay icon is ON,
Bypass icon is ON), This mode is activated by pressing
a function key programmed for Stay mode (default
key 1), or by arming the system by entering a valid
access code and not exiting the premises during the
delay period. If a function key programmed with No
Entry Arm is pressed or [*][9] is entered before
entering an access code there will be no entry delay. In
the ‘Stay Armed’ mode Stay/Away zones (zone defini-
tions 05 and 06) are bypassed and the remaining
zones are armed. In this mode [*][3], [*][5], [*][6] and
[*][8] functions can not be accessed.
Away Armed - (Ready light is OFF, Away icon is
ON),This mode is activated by pressing a function key
programmed for Away mode (default key 2), or by
arming the system by entering a valid access code and
exiting the premises during the delay period. If a func-
tion key programmed with No Entry Arm is pressed
or [*][9] is entered while the system is armed, No
Entry Delay will toggle. In the Away Armed mode
all zones are armed. Stay/Away zones (zone defini-
tions 05 and 06) will act as interior or delay zones
(zone definition 04 or 01). Zones may be bypassed in
this mode by entering [*][1]. In this mode [*][3], [*][5],
[*][6] and [*][8] functions can not be accessed.
[*] Functions - User functions enable the user to pro-
gram some aspects of the system. These functions are
accessed from the Ready mode and require a valid
access code. These functions include programming
access codes [*][5] and user functions [*][6]. See [*][5]
and [*][6] in ‘[*] Functions’, Chapter 3:Programming.
Installer functions ([*][8]) require the Installer’s
access code and allow Flash Programming and
Advanced programming. See Chapter 4: Flash
Programming and Chapter 5: Advanced program-
ming .
Zone Violations- When an armed zone is violated:
• The event is logged to the event buffer.
• The bell will sound (if enabled) for the duration of
Bell Timeout (BTO) or until a valid access code is
entered.
• An entry or exit delay may be initiated depending
on the zone type and if it has been enabled.
• One or more report codes will be sent to the cen-
tral station (if enabled).
If the system is disarmed while a zone is violated, the
Memory icon will be displayed. Re-arming the system
will clear the event from Alarm Memory. If an access
code is entered before the bell times out, it will be
silenced. If an access code is entered before the report
code transmission delay expires, the report code trans-
mission will be cancelled.
1-5.3 Access Codes
Duress Codes - Two duress codes can be pro-
grammed on the system. When a duress code is used
to perform any function the system will send a Duress
reporting code to the central station.
Master Code- The Master code can perform any key-
pad function and can be used to program all access
codes including master and supervisor codes.
Supervisor Codes- Supervisor codes can program
additional access codes. The attributes of the Supervi-
sor code are identical to that of the Master code by
default. These attributes can be changed in
[*][5][Mastercode][9] Attribute Programming.
Maintenance Code- The Maintenance code can only
be used to arm or disarm the system. This code can
not be used to bypass zones or perform any other
function. The Maintenance code is programmed in
Chapter 5: Advanced Programming.
Installer’s Code- The Installer’s code is used to set up
and program the system. The Installer’s code is 5555
by default but should be changed to prevent unau-
thorized access to programming.
firealarmresources.com

7
Chapter 2: Installation
2-1 Installation Procedure
Read the following procedure to familiarize yourself
with the necessary steps before installing the system.
1. Create a Layout - Draw a rough sketch of the
building and include all alarm detection devices,
modules and PGM output devices. Refer to the
following paragraphs for wiring requirements.
Keybus,Para 2-3.1
PGMs Para 2-3.2
Hardwired ZonesPara 2-3.3
Telephone Line Wiring.Para 2-3.4
Battery and AC Wiring. Para 2-3.5
Refer to paragraph 2-4 and the associated instal-
lation sheets for placement of wireless detectors.
Locate the control panel in a dry area, near an
unswitched AC source and telephone line. Avoid
areas that are a possible source of electrical noise
such as computers, televisions, appliances, HVAC
systems. Avoid areas with large metal surfaces
such as heating ducts.
☞Ensure that the control panel and other
modules will be installed in an area that
will be protected by the system.
2. Mount NT9204 Module - Mount NT9204 mod-
ule as indicated in the associated installation
manual. Mount hardwired and PGM output
devices as required.
3. Route Wiring - Route the telephone line, AC
power line, PGM wiring, hardwired zone wiring
or Keybus wiring to the NT9005 panel location.
4. Install NT9005 Back Cover- Route wiring
through the access holes provided and mount the
back cover. Refer to paragraph 2.2 ‘NT9005
Installation’.
5. Complete Wiring - Connect the telephone line,
AC power line, PGM wiring, hardwired zone wir-
ing or Keybus wiring to the back cover.
6. Power up Control Panel - Connect the backup
battery. Place the unit on mounting plate ensur-
ing that the header on the printed circuit board
aligns with the terminal block on the back plate.
☞The system will NOT power up if only the
battery is connected.
Ensure that the LCD display and buzzer are func-
tioning as described during the power up
sequence. See Start-up, paragragh 1-5.1.
7. Position and Enroll Wireless Detectors. This
can be performed in Flash Programming or sec-
tion [904] in Advanced Programming (placement
only). Refer to the Installation Sheets of wireless
devices to determine optimal placement. Mount
wireless devices after succesful placement. Refer
to appendices C, D and E.
8. Program the System. The system can be quickly
programmed for basic setup in Flash Program-
ming or custom programmed manually in
Advanced Programming or with DLS2002 (down-
loading software) using a remote or local com-
puter. See Chap. 3:Programming.
9. Test the System. Two system tests are available:
the user Walk Test available in [*][6][8] program-
ming or the installer Walk Test described in sec-
tion [901] in Advanced Programming.
☞In the User Walk Test report codes are not
sent to the central station.
firealarmresources.com

Installation
8
2-2 NT9005 Installation
The NT9005 back cover comes attached to the back
of the NT9005 control unit. The back cover acts as a
mounting plate for the unit and provides terminals for
connecting all wiring except the PC-Link connector to
the NT9005.
2-2.1 Back Cover Removal:
Figure 3.
1. Place the unit face down on a surface that will
not scratch or mar the front cover.
2. Remove the two screws (if required) securing the
back cover to the unit (located at the bottom of
unit). Retain the screws for reasssembly.
3. Press the tabs above the screw holes (Figure 3).
CAUTION:Resistance may be encountered
when removing the back cover. Remove the
back cover carefully from the unit to avoid
damage to the internal antennas
4. Lift the back cover clear of the unit.
5. Unhook the backplate from the top of the
NT9005.
2-2.2 Mounting the Back Cover
Locate the control panel in a dry area, near an AC source
and telephone line. Avoid areas that are a possible
source of electrical noise such as computers, televisions,
appliances, HVAC systems. Avoid areas with large metal
surfaces such as heating ducts.
The unit can be mounted on an electrical junction box
or directly to the wall. Refer to Figure 4 and para-
graphs 2-3.1 through 2-3.5 for wiring details.
Junction Box Mount
Route wiring from the junction box through the rect-
angular access hole (1) located directly above the ter-
minal block.
1. Secure the wiring to the appropriate terminals (2)
using a flat blade screwdriver.
2. Mount the unit on the junction box using the
screw holes (3) provided.
Figure 4. - Backplate of Unit
Wall Mount
CAUTION:Do NOT use the access hole located
at the top of the back cover (5) for wiring.
AC power routed close to the antennas or
microprocessor may cause interference with
the unit.
1. Route wiring through the access holes (1, 4) pro-
vided.
2. Continue through the wire guide (6) and exit
through the two square access holes (7) located
below the terminal block.
3. Re-enter the wiring through the rectangular
access hole (1) and secure to terminal block as
indicated above.
4. Position the back cover on the wall in the desired
location, and mark the screw locations (8, 3).
5. Using wall anchors for all screw locations, secure
the back cover to the wall.
firealarmresources.com

2-3 System Wiring
9
2-2.3 Mounting the Control Unit
1. Position the unit on the mounting tabs located at
the top of the back cover. Refer to Figure 5.
WARNING: Ensure that AC Power is OFF when mount-
ing the unit to the back panel. If the header terminals
are inserted into the incorrect terminals on the termi-
nal block, permanent damage to the unit may result.
2. Ensure that the two antennas are not obstructed,
bent or repositioned, the tamper switch spring fits
through the access hole to make contact with the
wall and that the header pins on the printed circuit
board are inserted into the correct terminals.
3. Slide tabs on bottom of unit into the slots of the
back cover.
4. Secure unit in place with the two screws provided.
2-3 System Wiring
The R, B, Y1, G2 terminals located on the inside of the
back cover, can be configured as a Keybus, or 2 hard-
wired zones or 2 PGMs (programmable outputs), or 1
PGM and 1 hardwired zone . If configured as a Keybus
or hardwired zone, wire devices using 22 AWG
stranded wire; maximum wire run distance must not
exceed 1000 ft. (305 m.).
Ratings: 9 VAC / 20 VA / 50/60 Hz.
2-3.1 Keybus Wiring
The Keybus is used to communicate to other modules on
the system. In this configuration the ‘R’ terminal is
+6VDC, the B terminal is ground, Y1 terminal is the
CLOCK and the G2 terminal is the DATA. If the system is
configured for Keybus then Keybus Enabled (section
[018] option 1) must be ON. Hardwired zones 1 and 2,
and PGMs 1 and 2 will not be available. If an NT9204
module is connected to the system (via the Keybus) then
PGMs 11, 12, 13 and 14 will be available. Enter [00] in
section [030] when an NT9204 is used.
☞The Keybus can not drive any module other
than the NT9204 directly. To connect to
LINKS2x50, an NT9204 module must be con-
nected to the Keybus.
Figure 5
Example of Keybus Wiring
Module A is wired correctly
(within 1000’/305m of the panel)
Module B is wired correctly
(within 1000’/305m of the panel)
Module C is NOT wired correctly
(greater than 1000’/305m from the
panel)
firealarmresources.com

Installation
10
2-3.2 Programmable Output Wiring
Programmable outputs (PGMs) are available directly
from the system panel or from the NT9204 module.
When activated, the output will switch to ground.
PGM outputs can be programmed in any of the
options listed in section [009] and can be customized
using up to 8 attributes, see section [141].
☞PGMs 3 through 10 are not supported at this
time.
PGMs 1, 2 - PGM 1 and 2 can sink 50 mA. This out-
put can drive an LED indicator or small buzzer directly.
Connect Y1 (PGM 1) or G2 (PGM 2) to the negative (-
) terminal of the device and connect the positive ter-
minal of the device to the R terminal. If current greater
than 50 mA, or voltage greater than 6 VDC is required
for an application then a relay must be used.
PGM 1 and PGM 2 - are programmed in section
[009], output attributes are programmed in section
[141] and [142].
PGMs 11, 12, 13, 14 - The NT9204 provides 4 high
current (1.0 Amp) programmable outputs that sink
outputs to a 12 VDC supply. These PGMs are pro-
grammed in section [011]; output attributes are pro-
grammed in sections [151] – [154].
2-3.3 Hardwired Zones
Two hardwired zones are available in three configura-
tions. Only one configuration can be selected for both
zones, and each must be wired according to the
selected configuration. The Y1 terminal is Zone 1 and
the G2 terminal is Zone 2. The B Terminal is common
for both zones. All wiring is connected between the
appropriate zone terminal and ‘B’ (common). To
enable this option, section [018] option 1 must be OFF
(default).
☞The default setup is for single EOL resistors.
These zones can be assigned to any zone number
through Flash Programming or Advanced Program-
ming (section [030]). Zone loop response time is pro-
grammed in section [ 031] (default = 500 ms).
☞Entering [00] in section [030] will configure
the associated terminal as a PGM output. To
configure the terminal as a zone, [01]-[32]
must be entered.
Enroll the Y1 terminal as 200001 and the G2 terminal
as 200002 (Flash Programming only). Hardwired
zones can be wired in any of the configurations indi-
cated below:
NC Loops with no EOL Resistor- This is the sim-
plest method of wiring hardwired zones. One or more
normally closed (NC) contact devices may be wired in
series between the Y1 terminal (Zone 1) and the B ter-
minal and/or the G2 terminal (Zone 2) and the B ter-
minal as required. No End-of-Line (EOL) resistor is
required.
☞Normally Open (NO) devices can NOT be used
in this configuration.
In this configuration there is no supervision or tamper
detection of zones. An open condition will sound an
alarm; a short circuit condition will not be indicated.
To program the system for this configuration, enter
Advanced Programming (See Chapter 3) and set sec-
tion [013] option [1] to ON.
Single End-of-Line (EOL) Resistors - In this configu-
ration normally closed (NC) devices as well as normally
open (NO) devices can be wired to the system. NC
devices are wired in series with a 5600 Ωresistor. NO
devices are wired in parallel with a 5600 Ωresistor.
Multiple devices can be wired in a series/parallel con-
figuration on a single zone as indicated below. The
number of devices that can be wired on a single zone
is limited by the wire run distance which must not
exceed 1000 ft. (305 m.).
firealarmresources.com

2-4 Wireless Device Placement
11
In this configuration the system should always see
5600 Ωwhen the zone is not violated. If the zone
becomes open or short the system will go into alarm.
There is no supervision or tamper detection of zones.
To program the system for this configuration, enter
Advanced Programming (see section 5) and set sec-
tion [013] option. [1] to OFF and option [2] to OFF.
Double End of Line (DEOL) Resistors - In this con-
figuration one NC (normally closed) contact device
may be wired for each zone between the Y1 terminal
(zone 1) and the B terminal and/or the G2 terminal
(zone 2) and the B terminal, as indicated below.
☞Normally Open devices or multiple devices
can NOT be used in this configuration
In this configuration the system should see 5600 Ωin
the normal state. If the zone becomes open, the sys-
tem interprets this as a tamper. If the zone becomes
short circuited the system will interpret this as a fault.
If the system sees 11,200 Ωthe system will interpret
this as a zone violation and will go into alarm.To pro-
gram the system for this configuration, set section
[013] option [1] to OFF and option [2] to ON (see
Chapter 5: Advanced Programming).
☞The hardwired zones of this product are
intended to be used with contacts or key-
switches. No power is available to power
motion or smoke detectors
2-3.4 Telephone Line
If a telephone line is required for central station commu-
nication or downloading, connect the RJ-31X telephone
line to the terminals indicated in the figure below.
2-3.5 Battery and AC Power.
☞Do NOT apply power until all wiring is com-
pleted.
☞The unit will not power up from the battery,
AC power must be connected.
1. Insert the two AC leads from the 9 VAC trans-
former into the terminal block on the back cover
and secure with a flat bladed screwdriver.
2. Connect the Red battery lead to the positive bat-
tery terminal and connect the Black battery lead
to the negative battery terminal.
3. Mount the control unit. See paragraph 2-2.3
2-4 Wireless Device Placement
Refer to the appendices in the back of the manual for
general guidelines on the placement of smoke detectors,
motion detectors and wireless contact transmitters. Refer
to the associated installation sheet for details.
☞Perform a Module Placement Test to verify
that the device is within range of the NT9005
before permanently mounting any wireless
device.
RJ-31x Telephone Connection
firealarmresources.com

12
Chapter 3: Programming
3-1 Programming Overview
There are three methods of programming the
NT9005: Flash Programming, Advanced Program-
ming, and downloading with DLS2002 Software.
[*] Functions
All operational functions and programming methods
are accessible through [*] functions. These functions
are accessed by pressing the [*] key and [0-9] keys to
select the function when the green Ready indicator is
on. These functions are listed below. See Paragraph
3-3, [*] Functions.
Flash Programming
Flash programming provides a quick method of pro-
gramming for installations that use the defaults pro-
vided, or as the basic setup before customizing other
options in Advanced Programming. The options that
can be programmed in Flash Programming are listed
below. See Chapter 4: Flash Programming:
Advanced Programming
Advanced Programming enables the installer to cus-
tom design all aspects of the system. See Chapter 5:
Advanced Programming.
DLS Software Programming
DLS software enables the installer to download/upload
programming using DLS software. Downloading can be
performed remotely with a computer, modem and tele-
phone land line, or locally using PC-Link.
3-2 Conventions Used
The symbols and conventions used in this section are
indicated below.
3-2.1 Programming Decimal Data
Some programming sections require decimal (0-9)
entries, such as zone defintions and system times.
Ensure that all entry data is recorded in the space pro-
vided before programming each section.
Most sections require a specific number of digits. Once
all digits have been entered the panel will automatically
exit the section and return to the previous menu.
[*][0] Quick Arm (while disarmed)
Quick Exit (while armed)
[*][1] Zone Bypassing (while disarmed)
Activating Bypassed Zones (while armed)
[*][2] Trouble
[*][3] Alarm Memory
[*][4] Door Chime ON/OFF
[*][5] Programming Access Codes
[*][6] User Function
[*][7] PGM Output Control
[*][8] Flash/Advanced Programming
[*][9] Arming without Entry Delay
1Serial Number Enrollment
2 Central Station Telephone Number
3 Central Station Account Code
4 Module Placement
 FLASH Indicates this function is available in
Flash Programming
[
[*] Function Indicates that this function can be
programmed in [*] functions
☞Indicates important notes
[*] Indicates that the keys enclosed in the
brackets are to be pressed
✓Indicates this is an option which can be
toggled ON or OFF. The checkmark indi-
cates that this option is the default.
I___I___I Indicates that decimal or hexadecimal
data entry is required
firealarmresources.com

13
If the [#] key is pressed, only the data entered will be
changed. All programming data remaining will be left
unchanged. For example, when programming tele-
phone numbers, press the [#] key after the number is
entered, to exit the programming section. This will
avoid entering all 32 digits.
3-2.2 Programming Hexadecimal Data
Hexadecimal or ‘hex’ digits are often required for a
programming section, such as telephone numbers
and reporting codes. To enter a hexadecimal number
press the [*] key followed by digits [1] through [6].
Digit [1] corresponds to hex A, digit [2] corresponds to
hex B, etc. The system will remain in the hexadecimal
programming mode until [*] is pressed. This will termi-
nate the hexadecimal mode, returning the system to
decimal mode.
For example to enter: ‘123A4BC5’
Enter: [1][2][3][*][1][*][4][*][2][3][*][5]
3-2-3 Programming Toggle Options
Many programming options are either toggled on or
off. These options are indicated by the check box ‘’
symbol. A check box with a check mark beside it ‘✓’
indicates that this is the default state. To toggle an
option on or off, press the digit corresponding to the
option number.
3-3 [*] Functions
All [*] function programming and operation are
detailed in the following sections.
[*] Functions
All programming of features, function keys, and priority keys
(Fire, Panic and Auxiliary keys) is accomplished through the [*]
functions. The default settings for the function keys, priorty
keys and the display can be found in Advanced Programming,
section [000]. To review the default settings for these features
refer to Advanced Programming sections [000] - [999]. The
complete list of [*] programming commands is detailed below.
To enter [*] functions [*][3], [*][5], [*][6], [*][8], [*][9]
begin from Ready mode.
Functions [*][0], [*][1], [*][2], [*][4]and[*][7] can be
entered when the system is armed or disarmed (Ready).
In Ready mode, the time will be displayed and:
The Ready light (grn) will be Steady ON
The Armed light (red) will be OFF
The Trouble light (amber) can be Steady ON or OFF
If there are alarms in memory the Memory icon will be
displayed.
If in a programming mode or other state press [#] to return to
Ready mode.
Press [*] Keypad will Beep
Display will Blank
Grn light will turn Off
Amber light will turn Off
Press [0] to [9] as required.
☞If a key is not pressed within 30 seconds the system
will return to Ready mode.
Press [#] at any time to return to ‘Ready Mode’
[*][0] Quick Arm/Quick Exit
When Disarmed - Entering [*][0] will arm the system when
the ‘Quick Arm’ feature is enabled (default ON).Quick arm
may be used as a convenience for regular users or when the
system will be armed by individuals unauthorized to disarm the
system. See section [015] option [4].
When Armed - Entering [*][0] when the system is armed will
allow the user 2 minutes to exit the premises through any
delay zone without altering the status of the system if the
Quick Exit feature is enabled (default ON) (section [015]
option 3). After [*][0] is entered, only one delay zone may be
tripped. If the delay zone is left unrestored at the end of the 2
minutes, it will begin the entry delay sequence. Any additional
activity on any other active zone will cause that zone to begin
its alarm or entry delay sequence. Quick Exit is not designed to
extend the standard Exit delay.
firealarmresources.com

Programming
14
[*][1] ZONE BYPASSING
When Disarmed - A bypassed zone will not cause an alarm. If
a zone is bypassed the panel can be armed (Ready light will be
on) even if the zone is open. Use zone bypass when access is
needed to part of the protected area. Damaged wiring or con-
tacts on a zone can be temporarily bypassed until repairs can
be made so that the panel can be armed.To bypass zones,
enter [*][1] (an access code may be required in order to gain
access if enabled by the installer).
Then enter the two digit zone number. While in this menu the
first two digits of the clock display will scroll through all zones
currently bypassed. Individual bypassed zones are not shown
while armed.
Bypass Recall – When [99] is entered on a keypad, the last
group of zones that were bypassed are recalled.
Clearing Bypasses – When [00] is entered on the keypad, all
bypassed zones are cleared. This includes zones that were
recalled as a Bypass group, or manually bypassed.
Bypass Groups – When in the [*][1] menu, manually bypass
the desired zones. When the desired zones are bypassed,
press [95] to store them in Group One, or press [96] to store
them in Group Two. These groups may be recalled by enter-
ing [91] for Group One or [92] for Group Two.
Activating Auto Bypassed Stay/Away Zones - When the
system is armed in the Stay mode by arming and not exiting
through a Delay zone during the exit delay or by pressing a
function key programmed for Stay Arm or Arming Without
Entry Delay [*][9], the zones programmed as Stay/Away
zones are automatically bypassed. This [*][1] command is used
to remove the automatic bypass from these zones to fully arm
the system. Once this command is executed, all Stay/Away
zones will follow the programmed Exit Delay time, and when
the Exit Delay expires, the panel will log Armed in Away
Mode. If the panel is armed in Away mode, pressing [*][1] will
cause the Stay/Away zones to become re-bypassed, thus log-
ging Armed in Stay Mode. If function keys require the enter-
ing of an access code, a valid access code must be entered to
toggle between arming modes. The access code used to per-
form this function will be logged with “User Log User XX”.
☞If armed with the Away function key it is not possible
to toggle to Stay mode.
[*][2] Trouble Announcements
The panel continuously monitors a number of possible trouble
conditions. If one of these conditions occurs, the keypad Trou-
ble indicator will light and the audible indication will sound
(two short beeps every 10 seconds), except for an AC failure.
When the [#] key is pressed the audible indication will stop but
the trouble is not cleared. Trouble conditions are logged to the
event buffer and can also be transmitted to the monitoring
station. Pressing [*][2] will cause the system to light icons 1-8
to indicate the trouble conditions listed below. Troubles 1, 5, 6
and 7 can be expanded for more details by pressing the corre-
sponding [1][5][6] or [7] key. Press [#] to return to the Ready
mode. There is no Trouble memory. The event buffer can be
used by DLS to perform this function.
☞Troubles can be viewed when the system is armed or
disarmed. option 3 in section [013] must be ON.
1Service Required
1. Low Battery - Standby battery voltage is mea-
sured under load every 4 minutes and during System
Test.
2. Future Use
3. General System Trouble
Any peripheral module trouble will be indicated and
communicated with a General Trouble but logged to
the event buffer with a detailed description.
* NT9204 Supply Trouble (excessive current draw or
short on Aux+)
* NT9204 Output Fault (no load on output 01. Strap
1k ohm resistor from 01 to Aux+ if not used)
* RF Jam verified (other signals are broadcasting on
433 MHz band)
4. General System Tamper - Any peripheral mod-
ule tamper or unit tamper will display and communi-
cate a General System Tamper. The details of this
event will be logged to the event buffer.
5. General System Supervisory - If the system
loses Supervisory signals from a peripheral module, a
General Supervisory trouble will be displayed and
communicated. The details of this event will be
logged to the event buffer.
6. RF Jam- Indicates a jamming signal has been
detected for more than 30 seconds.
7. NT9204 Low Battery - The NT9204 module has
a low battery condition.
8. NT9204 AC Fail - The NT9204 module has
detected an AC power failure. This Trouble will ini-
tiate the trouble beeps after the AC fail transmission
delay if Trouble #2 is NOT present.
firealarmresources.com

3-3 [*] Functions
15
2AC Failure - There is no audible annunciation on AC
power failure. The system Trouble light will come
ON, but the audible indication will not sound until
there is a low battery condition. Transmission delay
can be programmed for 000 to 255 minutes. If the
AC fails, the battery will be continuously checked
until the panel shuts down.
3TLM Trouble (Telephone Line Monitoring) - The
telephone line voltage is measured every 10 seconds.
If the voltage drops below 3 volts for the number of
consecutive checks programmed in section [370]
plus 2 additional checks, a Telephone Line Trouble is
generated. If TLM is enabled, it must perform at
least 3 checks (settings of 000 and 001 in section
[370] will result in 3 checks, setting of 002 will result
in 4 checks, setting of 003 will result in 5 checks,
etc). The actual display of the TLM trouble can be
delayed in Installer’s Programming.
4FTC (Failure to Communicate) - If the digital com-
municator is unsuccessful in communicating with
any of the programmed telephone numbers, a fail-
ure to communicate trouble will be generated. If a
later attempt to communicate is successful, the
panel can also transmit the FTC reporting code and
all previous unsuccessful events.
☞A Telephone #1 FTC will only occur after Telephone
#3 has had an FTC as well, if programmed in section
[303] and [380] option [5]
5Zone Fault - If any zone on the system is in the Fault
state, this trouble will be generated.
For hardwired zones using double-end-of-line super-
vision, this is the shorted state; for RF sensors, this is
a loss of Supervisory signals. If [5] is pressed in the
Trouble mode, the keypad will now display all of the
zones in trouble.
☞This trouble will be generated and displayed in the
armed state if a Fire trouble is present. It will also
restart the Trouble beeps. If any zone enters this
trouble state (short), the keypad buzzers will sound
trouble beeps to annunciate the condition.
6Zone Tamper - This trouble is used with DEOL Zone
Supervision or on any RF zone.
If any zone is in the Tamper state (hardwired or RF),
this trouble will be generated. Zones excluded from
this are Fire and zones not supporting the DEOL con-
figuration (e.g., keyswitch). If [6] is pressed in the
Trouble mode, the keypad will now display all of the
tampered zones. If any zone enters this Tamper state
(open), the keypad buzzer will sound trouble beeps
to annunciate the condition.
7Device Low Battery - If an RF Device reports a Low
Battery signal to the panel, this trouble will be gener-
ated.
1
2
3
4
Press [*][2][7] ; keypad beeps 2 times, scrolls
zones 1-32.
Press [7] again; keypad beeps 3 times,[Future
use]
Press [7] again, keypad beeps 4 times,to scroll
wireless keys 1-16.
Press [7] again, keypad beeps 2 times,to
return to zones 1-32. (Step 1)
8 Loss of System Time - When the panel is powered
up, the internal time of day clock must be set to the
correct time. This trouble is cleared when an
attempt is made to reset the internal time of day
clock.
[*][3] Alarm Memory
IF an alarm is in memory when the system is disarmed the
Memory icon will be turned ON. Press [*] then [3] to enter
the alarm memory mode. The Memory light will flash and
any alarm caused during the last armed period will be scrolled.
Press [#] to return to the Ready mode.
☞Arming the system will clear memory. When dis-
armed there is no memory of previous armed states.
The event buffer can be used to achieve this function
by uploading to a computer with DLS2002 software.
[*][4] Door Chime ON/OFF
When Armed or Disarmed the Door Chime feature is
used to sound a tone from the keypad whenever a zone
programmed as a Chime type is violated or restored.
When the Door Chime feature is turned ON, the keypad
will beep several times whenever a Chime zone is acti-
vated. To turn the feature on or off, enter [*][4]. If the
feature is being turned ON, the keypad will beep 3 times
and the keypad will display the Chime icon. If the feature
is being turned OFF, the keypad will sound a single long
tone and the keypad Chime icon will turn OFF.
firealarmresources.com

Programming
16
[*][5] Programming Access Codes
Enter [*][5][Master Code][01-32,33,34,40,41,42] to pro-
gram access codes.
Enter [*][5][Master Code][01-32,33,34,41,42][*] to delete
an access code. The code will be immediately erased and the
panel will return to access code programming.
User Codes (Access Codes 01 & 32)
User access codes are intended to be unique for
each user. This allows the system to identify the user
(by logging to the event buffer) when the system is
armed, disarmed etc.
☞
Duress Codes (Access Codes 33 & 34)
Duress codes 33 and 34 are standard user codes that
will transmit the Duress reporting code (if pro-
grammed) whenever the code is entered to perform
any function on the system.
Duress codes are not valid when entering [*][5],
[*][6] or [*][8] sections.
Master Code (Access Code 40)
The Master Code can only be changed by the Master
User or the Installer. If the Master Code is not
changeable, (section [015] option 6) is enabled;
then only the Installer can change this code.
Supervisor Codes (Access Codes 41 & 42)
These codes can only be programmed by the Master
Code. These codes are always valid when entering
the [*][5] User Code Programming section. How-
ever, these codes can only program access codes
which have equal or lesser attributes. Once pro-
grammed, the Supervisor Codes receive the
attributes of the Master Code. These attributes can
then be edited.
The default attributes of a new code will be the
attributes of the code used to enter [*][5] program-
ming. The Master Code has attributes 1, 3, 4 ON.
Enter [*][5][Master Code][9] [01-32,33,34,41,42]
to edit access codes attributes.
1 Arming, disarming, alarm reset allowed.
2 Future use.
3 Zone bypassing allowed.
4-6 Future use.
7 Bell Squawk on arming/disarming.
8 Future use.
☞Attribute 7 enables an access code to generate an
arming/disarming bell squawk on entry of the code.
[*][6] USER Functions
Enter: [*][6][Supervisor Code or Master Code][1-8] for
functions listed below.
1Time and Date - The default setting for time and
date is AM/PM Time; for 24-Hr time set section
[000][6] option 2 to OFF. Time must be entered in
24-Hr Time regardless of format. The format for time
and date is:
[*][6][Supervisor Code][1][HH][MM][mm][dd]
[yy]
HH = hours (00-23)
mm = month (01-12)
yy = year (00-99)
MM = minutes (00-59)
dd = day (01-31)
E.g., to set time and date to:
March 15, 2001, 6:15 PM enter:
[*][6][Supervisor Code][1][18][15][03][15][01]
To set time only enter:
[*][6][Supervisor Code][1][1800][#]
2Auto-arm Enable/Disable - Enter [*][6][2] to
enable (three beeps indicate that auto-arm is
enabled) or disable (one long beep indicates that
auto-arm is enabled).
3Auto-arm Schedule - Enter [*][6][3] followed by
[1-7] (Sunday-Saturday) to change the auto-arm
time for each day of the week. An icon will display
the current day. When the day you wish to change
has been selected, enter the auto-arm time in 24-hr.
format (e.g., hh:mm, 18:45 = 6:45 PM). The system
will return you to the day selection menu. Enter the
day you wish to select or enter [#] to exit auto-arm
programming.
4System Test - The system siren output, keypad dis-
play, lights, communicator and standby battery are
tested. The siren and all display icons will turn ON
for two seconds.
5Enable DLS - When this command is executed , the
system will open a window where calls from the
downloading computer will be detected by the sys-
tem. This window may be set to 1 Hour or Six Hours
(default).See section [702] option 7.
6User Call-up (default ON) -When this command is
executed , the system will make one attempt to call
the downloading computer. The downloading com-
puter must be waiting for the system to call for
downloading to occur. This must be enabled in sec-
tion [400] option 2.
7Not Used
firealarmresources.com