DSE DSE9701 User manual

D E E P S E A E L E C T R O N I C S
D S E 9 7 0 1 & D S E 9 7 0 2 B A T T E R Y C H A R G E R
I N S T A L L A T I O N I N S T R U C T I O N S
053-170
ISSUE 1
DANGER OF DEATH : LIVE PARTS exist ithin the Battery Charger
enclosure. The enclosure cover must not be removed.
Installation
The DSE9701 (24V 5A) & DSE9702 (12V 5A) battery charger are de igned to be mounted
vertically within a control panel, on the panel DIN rail utili ing the integral mount or on a cha i
utili ing the mounting hole . For dimen ion and mounting detail , ee overleaf.
DSE battery charger are fit-and-forget. They are permanently connected to the upply and the
load, with no requirement to di able the charger during time of heavy load ( uch a engine
cranking) or when in parallel with a charging alternator.
Battery Suitability
The charger i factory et by DSE to uit Lead Acid batterie but can be adju ted at the time of
ordering to uit other battery type .
Care mu t be taken to en ure the batterie connected to the charger are of the correct
‘technology’ to uit the etting of the charger.
Indications
The Battery Charger feature an LED indicator( ) to how the battery charger Status.
(Refer to DSE publication: 057-085 DSE9xxx Serie Operator Manual for further information)
Boost Mode
Boo t mode i operated by connecting the BOOST terminal together for in tance with an
external witch or timer circuit. Thi will rai e the battery charger floating voltage by 0.8V DC.
Typical Wiring Diagram
NOTE : This document is intended as a ‘quick start’ guide only. For full
operating instructions and specifications, refer to DSE publication: 057-085
DSE9xxx Series Operator Manual.
Connection Type Screw Terminal,
Ri ing Clamp,
No Internal Spring
Min Cable Size 0.5mm² (AWG 20)
Max Cable Size 2.5mm² (AWG 14)
DSE9701 AC Fu e
(230 V AC Supply)
2.0 A Anti-Surge
DSE9701 AC Fu e
(110 V AC Supply)
3.5 A Anti-Surge
DSE9702 AC Fu e
(230 V AC Supply)
1.0 A Anti-Surge
DSE9702 AC Fu e
(110 V AC Supply)
2.0 A Anti-Surge

Dimensions and Mounting
Overall Size for DIN Rail Mounting 47.5 mm x 152.8 mm x 111.2 mm
(1.9” x 6.0” x 4.4”)
Overall Size for Cha i Mounting 47.5 mm x 133.0 mm x 111.2 mm
(1.9” x 5.2” x 4.4”)
Weight 0.4 kg
Mounting Type DIN Rail or Cha i Mounting
DIN Rail Type EN 50022 35 mm Type Only
Mounting Hole
(DIN Rail Clip Pu hed Outward to
Reveal Mounting Hole )
Suitable for M4
Mounting Hole Centre 140.8 mm
(5.5”)
Input Voltage (Nominal) 110 V - 277 V
Input Voltage (Ab olute Range) 90 V - 305 V
Charge Failure Relay Rating 3 A DC Re i tive, 30 V Maximum
Operating Temperature -30 °C to 55 °C
(-22 °F to 131 °F)
Over Temperature Protection Above 70 ºC (158 ºF) the maximum output current i
limited to protect the device. Thi limiting increa e
linearly a temperature increa e until at 100 ºC
(212 ºF), the maximum output current i limited to 1
A DC.
Cha i Mounting DIN rail Mounting Dimen ion
Dimen ion in mm unle otherwi e pecified
Deep Sea Electronics Plc.
Tel:[phone]
Fax: [phone]
Email: ale @deep eaplc.com
Web: www.deep eaplc.com
Deep Sea Electronics Inc.
Phone: [phone]
Fax: [phone]
Email: ale @deep eau a.com
Web: www.deep eau a.com