DT Research DT363GL Assembly instructions

Rugged Handheld Tablet
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2021, DT Research, Inc. All Rights Reserved. BOG082321 DT363GL/ 363Q ENG LT
INTRODUCTION
Thank you for acquiring the DT363GL/ 363Q, part of DT Research’s line of Rugged
Tablets. Featuring a slim yet robust enclosure, the DT363GL/ 363Q with 6” TFT
display is powered by the Intel® Pentium® Silver quad-core or Qualcomm octa-core
processor, offering optimal combinations of performance and power savings. The
DT363GL/ 363Q is available with Microsoft® Windows® or Android operating system.
The software operating system features web browser, client/ server computing
software, media player, accessories, and applications support.
PACKAGE CONTENTS
• One DT363GL/ 363Q
• One Baery Pack
• AC-DC Power Adapter
• Basic Operaon Guide
* The actual package contents may vary depending on the conguraon acquired.
DT363GL/ 363Q
Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against harmful interference in
a residenal installaon. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Cauon: Any changes or modicaons not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules.
Operaon is subject to the following two condions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operaon.
This device and its antenna(s) must not be co-located or operang in
conjuncon with any other antenna or transmier.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.

Button Functions
BUTTON ACTION
Power Buon
Trigger Buons
Baery Latch
USB Type-C Port (power input)
SIM Card Reader (363Q)
SD Card Reader (363Q only)
Smart Card Reader (DT363GL only)
SIM Card Reader (DT363GL)
Speaker
Microphone
Barcode Scanner (oponal)
Front Camera (oponal)
Back Camera (oponal)
NFC/UHF RFID Reader (oponal)
1
2
3
C
D
E
B
A
2
PRECAUTIONS
• Always exercise care when operang and handling the DT363GL/ 363Q
• Do not disassemble any poron of the DT363GL/ 363Q, as this will void any
product warranty.
• Do not use any power adapter or charging cradle other than the one provided with
the tablet or acquired from the manufacturer or its partners.
• In the unlikely event that abnormal noise, strange odor, or smoke is present,
immediately power down the DT363GL/ 363Q and disconnect all power sources.
Please report the problem to your device provider immediately.
The DT363GL/ 363Q
A
B C
D IE J
G
K FH 1 32
F
G
H
I
J
K
Foldable
Antenna
3
OPERATION
Powering ON and OFF
To acvate DT363GL/ 363Q, push and quickly release the Power Buon. The display
will come on in a few seconds. To put the DT363GL/ 363Q in standby mode, push and
quickly release the Power Buon. To turn the DT363GL/ 363Q o for extended storage,
power o safely using any soware funcon that “shuts down computer” provided in
the soware operang system.
NOTE:
The baery packs shipped with your tablet may be low in power - please use
the AC-DC adapter with the DT363GL/ 363Q when seng up for the rst me to
fully charge the baery pack.
NOTE:
To conserve power, push and quick release the Power Buon to put the tablet in
standby mode while not in use. Pushing briey on the same buon will wake up
the system.
NOTE:
When the baery pack is charging, the blue-colored Baery LED should blink
slowly. If plugging in the AC-DC adapter does not trigger this blinking acvity
and the LED stays dark, the baery pack(s) may have been drained substanally.
Unplug/ replug the AC-DC adapter to the DT363GL/ 363Q a few mes to
acvate the charging process.
NOTE:
For DT363GL, avoid using the Power Buon (“hold 4+ seconds” feature) to turn
o the tablet—this form of hardware shutdown is intended to be a means of
recovery from lockups, and not as normal operaon.

5
UHF RFID Reader:
The oponal UHF RFID reader supports EPC Gen2V2 and ISO 18000-63 standard. To
develop an applicaon to use the UHF RFID reader, contact your device provider for a
UHF RFID reader API package.
Data Capture Module Operation Guide
If your DT363GL/ 363Q comes with a RFID Reader, refer to the steps below to congure
the sengs.
NOTE:
To ensure opmal system performance, turn on only the symbologies you are going
to use.
4
Start Up
If the power up (from Standby mode or otherwise) is successful, the appropriate
interface will be displayed aer a launch sequence of several seconds. The wireless
LAN connecon may take 10-15 seconds to be established.
Wireless Networking
Wireless LAN
The DT363GL/ 363Q is oen delivered with an embedded (user-inaccessible)
802.11ac LAN adapter equipped with a hidden custom antenna.
• Through the support of typical WLAN adapters, the DT363GL/ 363Q should be
able to detect all 802.11 access points in the vicinity for you to select the access
point of your choice for connecon.
• The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT363GL/ 363Q
and the access points have to match. The SSID is case-sensive and it is recom-
mended that you enable WEP/WPA/WPA2 encrypon (or advanced alternaves)
for secure access.
• When WEP/WPA/WPA2 is enabled, you may need to consult your network
administrator or your networking equipment literature to properly congure
associated sengs such as Authencaon mode, etc.
• Refer to the access point operang manuals for seng up the 802.11 access
points.
Bluetooth
The Bluetooth conguraon applicaon is enabled from the Windows System Tray
or from the Android Sengs APP. Follow the instrucons and opons provided
within the applicaon to congure and invoke Bluetooth connecvity with the
corresponding peripherals.

7
6
Installing the SIM Card on DT363Q
1. Make sure the tablet is completely powered o.
2. Open the top cover, then gently insert the SIM card into the appropriate slot.
3. Close the top cover.
Removing the SIM Card from the DT363GL/ 363Q
Gently push the SIM card in and quickly release. The card will parally eject and can
now be pulled out.
For More Support
Users can download the Tablet Modules Basic Operaon Guides from the DT Research
website.
If your DT363GL/ 363Q comes with a 4G LTE module, refer to the steps below to
install the SIM card.
Installing the SIM Card on DT363GL
1. Make sure the tablet is completely powered o.
2. Remove the two screws, remove the cover, then gently insert the SIM card.
3. Posion the cover over the card slot, aach both screws.