DT Research DT372 Assembly instructions

DT372
ENGLISH
Mobile POS Tablet
BASIC OPERATION GUIDE
DT372
ENGLISH 8
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2011, DT Research, Inc. All Rights Reserved.
DT Research is registered trademarks of DT Research, Inc.
INTRODUCTION
Thank you for acquiring the latest addion to DT Research’s line of mobile tablets—the
DT372. Featuring an IP54-rated, slim yet robust enclosure, the two-pound DT372 with
7”TFT display is powered by the Intel®Atom™ processor, offering opmal combinaons
of performance and power savings.
The DT372 is available with Windows®Embedded Standard 7, Windows®XP Embedded,
Windows®XP Pro for Embedded Systems, Windows®7 Pro or Linux operang systems.
Each soware operang system features web browser, client/server compung
soware, media player, accessories, and applicaons support.
PACKAGE CONTENTS
DT372 with Internal Baery Pack, Stylus and Bumpers•
AC-DC Power Adapter with Power Cord•
Basic Operaon Guide•
Major opons, depending on configuraon:
Desktop Charging Cradle with DC-in Power Jack and Ethernet/ USB Ports•
Handstrap•
* If your DT372 contains MSR, camera or scanner module, please refer to the POS module operaon guide for
detailed operaon.
BOG121611DT372ENG
SPECIFICATIONS
System
Processor Intel® Atom™ Z530, 1.6GHz
Memory (RAM) 2GB
Storage 2GB to 32GB Flash
Operang Systems
Microso® Windows® Embedded Standard 7,
Windows® 7 Professional, Windows® XP Embedded,
Windows® XP Pro for Embedded Systems, or Linux
Display 7”LED-backlight screen with resisve touch;
sunlight-readable opon
Display Resoluon 1024 x 600 (WSVGA)
Network Interface Wi-Fi 802.11a/b/g/n, Bluetooth 2.1 with EDR
Control Switch and Buons 1 power buon, 5 front buons and 1 trigger buon
Indicator 1 power/ baery status LED and 1 WLAN acve LED
Speaker/Microphone Built-in speaker; built-in internal microphone
Input/Output Ports 1 DC-in Jack; 1 USB 2.0 port;
1 Headphone-out Jack combined with microphone
Power
AC/DC Adapter Input: 100 – 240V AC; Output: 19V DC, 2.36A
Baery Pack Removable 7.4V, 3760mAh
Mechanical
Enclosure ABS + PC plascs
Stylus Non-electronic p
Protecve Grip Rubber
Dimensions (H x W x D) 7.4 x 9.3 x 1.6 in/ 190 x 237 x 41 mm
Weight 2.43 lbs/ 1.1 kg
Environmental
Water and Dust Resistance IP64 * IP64 rang may not be applicable for units with MSR or
Smart Card Reader module opons
Regulatory FCC Class B, CE, C-Tick, RoHS compliant
Temperature Operaon: -10°C - 50°C; Storage: -10°C - 60°C
Humidity 0% - 90% non-condensing
* Specificaons subject to change without noce.

DT372
ENGLISH 23ENGLISH
Buon Funcons (with Windows XP Operang System)
BUTTON ACTION
Programmable
Programmable, launch so(on-screen) keyboard (default)
Launch SAS (Secure Aenon Sequence)
Generate Ctrl+Alt+Del keys to invoke the security windows defined under Windows XP
Programmable,
Change display orientaon (portrait/ landscape) (default)
Programmable, system ulity menu (default)
Power on,
Push/release typically enters Standby mode, or Push/release exits Standby mode or
restarts device (soware dependent)
Push and hold (over 4 seconds) invokes hardware shutdown
Programmable,
As scanner trigger when equipped with the scanner module
The DT372 (with Windows XP Operang System)
Baery/Power LED
StylusWireless LED
Microphone
Buon ManagementWireless Network Sengs
Calibraon
Power/Baery LED Status:
Blue indicates the baery is 25% to 100% charged•
Blinking blue indicates the baery is charging•
Orange indicates that the baery is between 11% to 25%•
Blinking Orange indicates that the baery is below 10%•
Precauons
Always exercise care when operang and handling the DT372.
•
Do NOT apply excessive pressure to the display screen.
•
We recommend using the Stylus provided to keep the screen clean.
•
Avoid prolonged exposure of the display panel to any strong heat source. Wherever
•
possible, the DT372 should face away from direct light to reduce glare.
If the AC-DC power adapter is used to recharge or power the device, do NOT use any
•
AC-DC adapter other than the one provided with the device or acquired from the
manufacturer or its partners.
In the unlikely event that smoke, abnormal noise, or strange odor is present,
•
immediately power offthe DT372 and disconnect all power sources. Report the
problem to your device provider immediately.
Never aempt to disassemble the DT372, as this will void the warranty.
•
THE DT372
Basic Features
The DT372 wireless tablet integrates a bright and responsive touch display, 1 USB
port, and embedded networking elements such as wireless LAN, Bluetooth or oponal
3G. The primary device is complemented by a suite of accessories, including baery
expansion, docking cradles, and carrying cases, for a comprehensive user experience.
A DT372 typically integrates an 802.11a/b/g/n wireless LAN (WLAN) adapter that may
connect to other wireless devices or access points. If your DT372 does not come with
such a network adapter, please consult your device provider to establish the desired
network connecvity.
1
7
6
2
3
4
6
7
5
Input/ Output Ports
DC Power Input
USB Port
Headphone Jack
A
C
B
A
B
C
12345
Baery and Power Meter
Front View
Le
Right
Rear View

DT372
ENGLISH 45ENGLISH
OPERATION
Internal Baery
Warning!
The Internal baery pack should only be replaced by an authorized DT Research service
representave. Please contact your product and/or service provider for internal baery
replacement service.
Powering ON and OFF
To acvate the DT372, use the stylus to push and quickly release the Power Buon. The
display will come on in a few seconds. To put the DT372 in Standby mode, push and
quickly release the Power Buon. To turn the DT372 offfor extended storage, power off
the device safely using any soware funcon that “shuts down computer”provided in
the soware operang system.
NOTE: The baery packs shipped with your device may be low in power—please use
the AC-DC adapter with the DT372 when seng up the device for the first me to fully
charge the internal baery pack.
NOTE: When the baery pack(s) is (are) charging, the blue-colored Baery LED should
blink slowly. If plugging in the AC-DC adapter does not trigger this blinking acvity
and the LED stays dark, the baery pack(s) may have been drained substanally. Try
unplugging/ replugging the AC-DC adapter to the DT372 a few mes to acvate the
charging process.
NOTE: To conserve power, use (push and quick release) the Power Buon to put the
device in “Standby”mode while not in use. Pushing briefly on the same buon will wake
up the system within seconds.
NOTE: Avoid using the Power Buon (“hold 4+ seconds”feature) to turn offthe
device—this form of hardware shutdown is intended to be a means of recovery from
device lockups, and not as normal operaon.
Start Up
If the power up (from Standby or otherwise) is successful, the appropriate interface will
be displayed aer a launch sequence of several seconds. The wireless LAN connecon
may take 10-15 seconds to be established.
Configuring the DT372
The device may be configured using the ulies and methods dictated by the soware
operang system. The DT372 should be configurable for various properes such as user
profiles, network features, and several system elements.
Calibraon
The touch display for the DT372 is calibrated before shipping. In the event that the
calibraon has been modified or is unsasfactory, the respecve calibraon rounes
(e.g., PenMount (PM) for Windows XP) to calibrate the touch interface may be used.
Such applicaons are typically executed through touch input via Stylus or through mouse
click via a USB mouse.
Wireless Networking
Wireless LAN
The DT372 is oen delivered with an embedded (user-inaccessible) 802.11a/b/g/n
WLAN adapter equipped with a hidden custom antenna.
T
•hrough the support of typical WLAN adapters, the DT372 should be able to detect
all 802.11 access points in the vicinity for you to select the access point of your
choice for connecon.
T
•he SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT372 and the
access points have to match. The SSID is case-sensive and it is recommended
that you enable WEP/WPA/WPA2 encrypon (or advanced alternaves) for secure
access.
W
•hen WEP/WPA/WPA2 is enabled, you may need to consult your network admin-
istrator or your networking equipment literature to properly configure associated
sengs such as Authencaon mode, etc.
R
•efer to the access point operang manuals for seng up the 802.11 access points.
!

DT372
ENGLISH 67ENGLISH
Bluetooth
The DT372 features a built-in Bluetooth adapter that operates on the Microso
Windows Bluetooth protocol. The Bluetooth configuraon applicaon is invoked from
the System Tray or from the Control Panel for Windows XP. Follow the instrucons and
opons provided within the applicaon to configure and invoke Bluetooth connecvity
with the corresponding peripherals.
NOTE: Bluetooth devices or accessories that are not compable with the Microso
Windows Bluetooth protocol may not work with the DT372.
Buon Management
Where supported by soware, many of the hard buons on the DT372 are
programmable to perform a funcon of the user’s choice. The excepon is the Power
Buon and the SAS Buon. To acvate the buon re-assignment applicaon, invoke the
Buon Manager applicaon, e.g., in Windows XP Embedded .
Brightness Control
Where supported by device firmware and soware, a hard buon may be engaged to
manipulate the display brightness. Press the System Menu buon (Buon 7) on the front
of the DT372. The System screen will display a Brightness control secon with up and
down arrows that can be acvated with the stylus.
Baery and Power Management
The DT372 is equipped with an internal 3760mAh Li-Ion baery pack that is capable
of supporng approximately 3 - 4 hours of connuous operaon. The period between
baery recharges can be significantly lengthened by pung the device into Standby
mode through the Power Buon (see Buons Funcon Table) whenever the device is
not in use. Depending on the operang soware, the DT372 may also be configured to
enter various power-saving modes via the Power Buon or through med entry.
Desktop Cradle
The DT372 is complemented by an oponal Desktop Cradle for support, pass-through
charging, and connecon to a range of USB peripherals, including keyboard and mouse.
The Cradle offers the following interfaces: a DC-in port for the AC-DC adapter, an
Ethernet port, and USB ports. Always seat the DT372 securely onto the cradle. The cradle
must be powered by the AC-DC adapter for the Ethernet and USB ports to funcon. The
baery packs on the DT372 may be recharged by connecng the AC-DC adapter directly
to the DC-in port on the DT372 or through the DC-in port on the Desktop Cradle while
the DT372 is docked to the Cradle.
USING THE DT372
Memory & Storage configuraon
The DT372 is available with 2GB memory configuraon. Storage opons currently range
from 2GB to 32GB flash memory.
Peripherals Support
Through its USB ports, the DT372 supports a wide range of USB-based peripherals.
These peripherals are applicable for soware installaon, applicaons storage, data
storage, and system soware recovery and updates. The DT372 is also compable with
custom mountable cradle opons. These securable and mountable cradles provide an
interface to VESA mounts and arms, and to ports that may include USB, Ethernet and
pass-through power.