DT Research DT398 SERIES User manual

www.dtresearch.com
Mobile POS Tablet
Barcode Scanner
Buon Management
The default scanner trigger buon is on the right side.
To assign the Scanner Trigger buon, follow the steps
below.
1. Start Buon Manager by clicking on in the
system tray.
2. Select an available unused buon marked with the
icon .
3. Click on to go to the second screen of Buon
Manager.
4. Click on the icon to assign the Scanner Trigger to the unused buon.
5. Click OK to apply conguraon sengs and close the window.
Installaon
The Barcode Scanner is preinstalled as an opon for the DT398 series.
www.dtresearch.com Scanner 1/2
Barcode Scanner
Trigger Buon
DT398 SERIES OPERATION GUIDE
To Connect Barcode Scanner Module
To connect the Barcode Scanner, you can use the Keyboard Wedge. Tap on the icon in the
task bar, a menu displays as shown in the picture below. Select Connect Scanner.
Scanner connected

www.dtresearch.com
To Test Barcode Scanner Module
Click 1. Start | All Programs | Accessories | NotePad to run the Notepad.
Scan one of the several supported barcodes. 2.
The output will appear in the Notepad screen.
Verify the captured data.3.
The Default Port Parameters for Barcode Scanner Module
Port COM3
Baud Rate 115200
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
Note: Please refer to Hyper Terminal Sengs to conrm or change the port parameters.
SPECIFICATIONS
Scanning
Performance
Scan rate 60fps auto adapve
Scan angle Tilt: 360°/ Pitch: ±45°/ Skew: ±65°
Opcal resoluon CMOS 844 X 640 pixels
Print contrast down to 20%
Note: Specicaons are subject to change without noce.
Linear Imager Compliance and Precauon
This product complies with the following standards for laser and LED safety.
IEC 60825-1 Class2 LASER Product
Scanner 2/2
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2015, DT Research, Inc. All Rights Reserved.

www.dtresearch.com
Mobile POS Tablet
CMOS Camera
Installaon
The CMOS Camera is preinstalled as an opon for the series.
Buon Management
To assign Camera Trigger buon, follow the steps below.
1. Start Buon Manager by clicking on in the system tray.
2. Select an available unused buon marked with the icon .
3. Click on to go to the second screen of Buon
Manager.
4. Click on the icon to assign the Camera Trigger to the
unused buon.
5. Click OK to apply conguraon sengs and close the window.
Camera 1/2
DT398 SERIES OPERATION GUIDE
Camera
Camera
To Test CMOS Camera Module
To test the CMOS Camera, launch DTSMCap Ulity from Start | All Programs | Ulies.
Select File | Set Capture File to assign the locaon of the captured les.
Click Opons | Preview to
preview the capture screen.
Click Devices to select your
camera device.
Take a picture from Snap | Go
Capture the Video from
Capture | Start Capture to
start and Stop Capture to
end it.
You also can trigger from the
assigned buon, then edit
the captured les
4
4
4
4
4

www.dtresearch.com
SPECIFICATIONS
Front Camera
Sensor 1/5” CMOS sensor
Resoluon Sll Image support up to 1600(H) x 1200(V) pixels
Automac Image Control
Automac Exposure Control
Automac White Balance Control
Automac Gain Control
Focusing Type Auto focus @ 10cm
Back Camera
Sensor 1/4” CMOS sensor
Resoluon Sll image support up to 2592(H) x 1944(V) pixels
Automac Image Control
Automac Exposure Control
Automac White Balance Control
Automac Gain Control
Focusing Type Auto focus @ 10cm
Note: Specicaons are subject to change without noce.
Camera 2/2
∞
~
∞
~
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2015, DT Research, Inc. All Rights Reserved.

www.dtresearch.com
Mobile POS Tablet
RFID Reader
Installaon
The RFID reader is preinstalled as an opon
for the DT398 series.
The Default Port Parameter for RFID Module
Port COM4
Baud Rate 9600
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
RFID Reader
RFID
DT398 SERIES OPERATION GUIDE
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2015, DT Research, Inc. All Rights Reserved.
To Test RFID Reader Module
Click 1. Start | All Programs | Accessories | NotePad to run the Notepad.
Place an RFID tag or RFID card within range of the RFID 2.
Reader. (see reading range in specicaons). The output
will appear in the Notepad screen.
Verify the captured data.3.
SPECIFICATIONS
Frequency 13.56MHz ±7 KHz
Reading Range Within 30mm
HF RFID Reader ISO 15693,1443A(B), 18000-3 mode-1
To Connect RFID Reader Module
To connect the RFID, you can use the Keyboard Wedge. Tap on the icon in the task bar, a
menu displays as shown in the picture below. Select Connect RFID.
RFID connected