DT Research 306Q Assembly instructions

Rugged Handheld Tablet
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2020, DT Research, Inc. All Rights Reserved. BOG112420 306Q ENG
INTRODUCTION
Thank you for acquiring the 306Q Rugged Handheld Tablet. The 306Q oers a
6” capacivetouch display, Qualcomm processor, and Android operang system
in a compact, rugged, and lightweight package. The 306Q enablesecient
point-of-service/sales applicaons, inventory management, and eld services.
The DT306 provides the precise features needed to streamline operaons and
improveproducvity, data accuracy, and service.
PACKAGE CONTENTS
• One 306Q
• One Baery Pack and Handstrap
• AC-DC Power Adapter
• Basic Operaon Guide
* The actual package contents may vary depending on the conguraon acquired.
306Q
Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against harmful interference in
a residenal installaon. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Cauon: Any changes or modicaons not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules.
Operaon is subject to the following two condions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operaon.
This device and its antenna(s) must not be co-located or operang in
conjuncon with any other antenna or transmier.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.

Button Functions
BUTTON ACTION
Power Buon
Baery Latch
Trigger Buon
Input/ Output Ports
USB Type-C Port
Data Capture Modules
Barcode Scanner (oponal)
Magnec Stripe Reader (oponal)
Camera
1
2
3
A
C
D
B
23
PRECAUTIONS
• Always exercise care when operang and handling the 306Q.
• Do not disassemble any poron of the 306Q, as this will void any product
warranty.
• Do not use any power adapter or charging cradle other than the one provided
with thetablet or acquired from the manufacturer or its partners.
• In the unlikely event that abnormal noise, strange odor, or smoke is present,
immediatelypower down the 306Q and disconnect all power sources. Please
report theproblem to your device provider immediately.
The 306Q
1
3
2
A
B
CD
OPERATION
Powering ON and OFF
To acvate the 306Q, push and quickly release the Power Buon. Thedisplay will come
on in a few seconds. To put the 306Q in Standby mode,push and quickly release the
Power Buon. To turn the 306Q o forextended storage, press the power buon and
then follow the steps on the screen.
NOTE:
The baery packs shipped with your tablet may be low in power - please usethe
AC-DC adapter with the 306Q when seng up for the rst meto fully charge
thebaery pack.
NOTE:
To conserve power, push and quick release the Power Buon to make thetablet
in standby mode while not in use. Pushing briey on the same buonwill wake
up the system.
BASIC MODULE OPERATION
3 steps to capture the data results from Keyboard Wedge:
1. Turn on module from the Keyboard Wedge App
2. Launch a note-related App
3. Capture the data and verify the result
Data Capture Module Operation Guide
If your 306Q comes with a Barcode Scanner, RFID Reader and/or MSR module(s),
youmay refer to the steps below to congure the sengs.
BARCODE SCANNER
Launch the scanner module, and adjust the parse data format :
1. Tap the Keyboard Wedge App , select SCAN tab,
and turn on the Scanner module
2. Key in Prex and Sux codes to adjust the parse data
format
3. Click OK
NOTE:
To ensure the system performance, turn on only the symbologies you aregoing to use.