DURAVIT SensoWash Starck f User manual

SensoWash®Starck f
Mounting instructions Shower toilet unit
# 612000 01 1 00 1321
# 612000 01 2 00 0320
# 612001 01 1 00 1311
# 612001 01 2 00 0310

en
About the mounting instructions
These mounting instructions come as part of the Duravit
product and should be read carefully prior to installation.
Target readership and qualifications
The product and associated water connection should only be
installed by qualified plumbers. The electrical installation
should only be carried out by qualified electricians.
Explanation of the signal words and symbols
DANGER Indicates a hazardous situation
which, if not avoided, will result in
death or serious injury.
WARNING Indicates a hazardous situation
which, if not avoided, could result
in death or serious injury.
CAUTION Indicates a hazardous situation
which, if not avoided, could result
in minor or moderate injury.
NOTICE Is used to address practices not
related to physical injury.
Link to the Electrical Installation section
Link to the installation information in this section
Link to other instructions
Link to the Water Installation section
Inspection (e.g. for scratches)
Do not kink hose
Check for leaks and leak-tightness
Safety instructions
Risk of fatal electric shock!
> The product has to be correctly earthed. Do NOT operate the
product without proper grounding.
> Do NOT remove individual components.
> Connect the product only to the specified power supply.
> NEVER touch the power supply cable with wet hands.
> When working on electric components, disconnect the power
supply.
> If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
> Check rated power and choose cable cross section
accordingly.
Product and/or property damage
> Do NOT install the product in a room exposed to excessive
moisture. Ensure sufficient ventilation to avoid condensation
in electric components.
> Only use the parts in the installation kit to avoid
malfunctions.
> Do NOT use attachments not recommended by Duravit.
Freezing water
If the room temperature is too low, this can cause damage to
the product.
> Do NOT install the product in rooms where there is a danger
of frost. The room temperature must not be less than
4 °C (39 °F).
Condensation
Condensation may occur when moving from a cold location to a
warm location and can cause damage to the product.
> Leave the unit switched off for a few hours if it has been
moved from a cold location to a warm location.
Standards and regulations
The breach of local and country-specific regulations and
standards can cause damage to the product and/or property
damage.
> Local installation regulations, country-specific standards
and the Low Voltage Directives shall be observed at all times.
457361_Mounting_SeWa_Starckf_TW_RE/20.04.2

en
Mounting instructions
Please read the pre-installation information sheets prior to the
installation. These are available to download on the Internet at
www.pro.duravit.com.
An installation video of the Starck f wall-mounted WC is
available at www.duravit.com/mnt_sewa_starck_f.
Simply use this QR code
The installation of the Starck f One-piece water toilet differs
from the installation shown in the video (see installation
instructions One-piece water toilet).
2
Connecting the hose
> Use the hose stored from the installation of the wall-
mounted toilet.
4
+
21
Choosing and installing mounting clip
The delivery contains two mounting clips.
> Choose clip according to cable diameter.
9
-
10
Installing interface with actuator plate (optional)
> Install Interface Set for functional interface with
DuraSystem®actuator plate A2.
43
+
57
Testing
> Connect the power and water supply.
> Confirm that the product functions properly according
to the operating instructions.
51
Install anti-theft protection
> To fix the remote control permanently to the wall holder
go to step 53.
57361_Mounting_SeWa_Starckf_TW_RE/20.04.2 5

en
Pre-installation
> Install electrical connection according to the technical
drawing of the toilet.
DANGER Risk of fatal electric shock
> Disconnect electrical components from the power supply
before the installation.
> Check that all components are de-energised.
> Prevent the power supply line from being switched on
accidentally by third parties.
> Ensure that there is no damage to the power supply cable.
> Lay a permanent power supply line which must be on a
separate circuit:
> Observe the position of the electrical connection
> Leave at least 800 mm (31½ ") of feed cable exposed
> Install circuit breaker
> If the product itself does not have electrical leakage
protection function, it must be installed in circuit where
there is leakage protection device installed.
> Means for disconnection must be incorporated in the
fixed wiring in accordance with the wiring rules and
having a contact separation in all poles that provide full
disconnection under overvoltage category III conditions.
6
+
23
Connecting the cable
> Remove the insulation from the wires approximately
10mm (⅜ ").
> Connect the 3 wires to the terminal block. Observe the
L, N and PE conductors.
> Confirm that the grounding wire is 10 mm (⅜ ") longer
than the L and N wire.
Rated voltage
# 612... .. 2 .. .... 220 – 240 V 50 – 60 Hz
# 612... .. 1 .. .... 100 – 120 V 50 – 60 Hz
(Taiwan models)
Max. rated power 1080 W
Circuit breaker IN= 16 A
RCD IN= 30 mA
Protection degree IP X4
Protection class 1
Pre-installation
> Install water connection and water outlet according to the
technical drawring of the toilet.
WARNING Health risk and potential product
damage!
> Supply the product with tap water from the main water
system only.
> Do not connect any waste water, grey water, industrial water,
sea water or other untreated or semi-treated water.
NOTICE Product damage due to limescale build-up
In regions with hard water, limescale build-up can impair the
performance of the product.
> Check the water quality in your region. Duravit recommends
the installation of a water softener with water hardness
≥14°dH (2.5 mmol/l).
> Make sure to descale the product regularly. The app will
send an automatic reminder. Adjust the descaling settings
according to the water hardness in your region
(→ App: Menu – Care – Descaling).
> Only use descaling agents provided or approved by Duravit.
Water hardness Descaling cycle
soft <8.4° dH (1.5 mmol/l) every six months
moderate 8.4 – 14° dH (1.5 – 2.5 mmol/l) every six months
hard >14° dH (2.5 mmol/l) quarterly
Cold water DN15 (½ ")
Water pressure 0.07 – 0.75 MPa
(10 – 109 psi)
Water hardness max. 2.4 mmol/l (240 ppm)
657361_Mounting_SeWa_Starckf_TW_RE/20.04.2

57361_Mounting_SeWa_Starckf_TW_RE/20.04.2 31
# 612001 01 1 00 1311
# 612001 01 2 00 0310
# 612000 01 1 00 1321
# 612000 01 2 00 0320

L
NPE
1
2
– –
1
2
# WD5003 012 000 # WD5003 012 000
32 57361_Mounting_SeWa_Starckf_TW_RE/20.04.2
A B A
23
456
789
10 11 129
8
76
5
43
21
10 11
118 19 32

2x M4x16
1
2
1
2
1
2
1
2
57361_Mounting_SeWa_Starckf_TW_RE/20.04.2 33
13 14 15
16 17 18
19
18
171615
141312

12
1
248 mm
1 ¾“
–––– ++––
34 35 47 57 40 43 36 43 44 46 51 57
2x M4x16
57361_Mounting_SeWa_Starckf_TW_RE/20.04.2 35
13 14
19
22 23 24
33
3231
34 35 36

Ø 5 mm
Ø ¼”
2x S5 2x ST8x30
1
2
1
2
36 57361_Mounting_SeWa_Starckf_TW_RE/20.04.2
123
456
7
10 11 12464544
43
4241 40
393837

1
2
M2x8
43 mm
1 ¾“ Ø 5 mm
Ø ¼”
2x S5
2x ST4x20
57361_Mounting_SeWa_Starckf_TW_RE/20.04.2 37
13 14 15
16 17 18
19 20 21
22 23
555453
5251 50
494847
56 57